user guide - Replay XD

user guide - Replay XD
USER GUIDE
A
B
5V/1A OUT
C
D
Replay XD RePower 4400 mAh Battery Pack
(A) Mini USB 8-pin connector
DC 5V Input
(B) 2.5mm threaded DC jack
DC 5V 1A Output
(C) 4 Status LED’s, Charging and Power Level
(D) Power On/Off
O R I E N TAT I O N
A
B
5V/1A OUT
C
D
1. Make sure the Power (D) is off.
2. Plug a Replay XD1080 Mini USB-8 pin cable into
the RePower 4400 5V IN USB port (A).
3. Plug the opposite end into a Replay XD power
adapter, car charger, or a PC/Mac USB 2.0 port.
4. The status LED’s will illuminate one by one (C) to
tell you it’s charging.
5. The status LED’s (C) will illuminate all 4 LED’s
when the battery is full and charging is complete.
Note: The Mini USB port is for charging only. Do not
power on during charging.
CH A R G I N G
A
B
5V/1A OUT
C
D
1. Insert the male 2.5mm threaded DC jack from one
of the Replay XD DC HW Battery kits into the DC
5V 1A Output port (B) and gently screw it on and
tighten lightly.
2. Make sure the other side of the HW Battery kit is
securely attached to your camera.
3. Press the Power button (D) to turn on the RePower
4400 battery pack, the 4 status LED’s (C) will
illuminate and provide power to your camera.
O P E R AT I O N
A
B
5V/1A OUT
C
D
1. When the RePower 4400 is powered on,
the 4 status LED’s (C) will illuminate.
4 LED’s - FULL 100% Charge
3 LED’s - 66% Charge or less
2 LED’s - 33% Charge or less
1 LED - 10% Charge or less
P O W E R S TAT U S
Replay XD RePower 4400 mAh Battery Pack
OUTPUT POWER:
BATTERY TYPE:
CHARGE VOLTAGE:
CHARGE CURRENT:
CHARGE INPUT:
DC OUTPUT:
CONTROL KEY:
LED INDICATOR:
DC 5V / 1A
Li-ion cell 18650-4400 mAh x 2
5V
1A
Mini USB 8-pin connector
2.5mm threaded DC jack
Power Button
Power LED
Battery Level LED
DIMENSIONS: 24 mm Dia. (0.94 in)
97.5 mm Length (3.8 in)
22.9 mm Mounting Dia. (0.90 in)
WEIGHT: 76 grams (2.6 oz)
S P ECI FI C AT I O N S
IMPORTANT SAFETY AND HANDLING INFORMATION
WARNING: Failure to follow these safety instructions could result in fire,
electric shock, or other injury or damage to the Replay XD RePower 4400
battery or other property.
Handling
The Replay XD RePower 4400 battery contains sensitive components. Do not
drop, disassemble, open, crush, bend, deform, puncture, shred, microwave,
incinerate, paint, or insert foreign objects into the Replay XD RePower 4400
battery. Do not use the Replay XD RePower 4400 battery if it has been
damaged—for example, if Replay XD RePower 4400 battery is cracked,
punctured, or damaged by water.
Avoiding Wet Locations
Do not use the Replay XD RePower 4400 battery in rain, or near wash
basins or other wet locations. Take care not to spill any food or liquid on the
Replay XD RePower 4400 battery. In case the Replay XD RePower 4400
battery gets wet, turn off and unplug from camera before cleaning, and
allow it to dry thoroughly before using again. Do not attempt to dry the
Replay XD RePower 4400 battery with an external heat source, such as a
microwave oven or hair dryer. Damage to the Replay XD RePower 4400
battery caused by contact with liquid is not covered under the warranty.
Using Connectors and Ports
Never force a connector into a port. Check for obstructions on the port. If
the connector and port don’t join with reasonable ease, they probably don’t
match. Make sure that the connector matches the port and that you have
positioned the connector correctly in relation to the port.
This symbol on the product or in the instructions means that
your electrical and electronic equipment should be disposed
at the end of its life separately from your household waste.
There are separate collection systems for recycling in your
country. For more information, please contact the local
authority or your retailer where you purchased the product.
S A FE T Y & U S AG E
STABLE IMAGING SOLUTIONS, LLC. LIMITED WARRANTY
WHAT THE WARRANTY COVERS
Stable Imaging Solutions, LLC. (SIS) warrants for 180 days from the
date of purchase of product it will be free from defects in material and
workmanship.
WHAT IT DOES NOT COVER
This warranty does not cover damage due to:
• Accidents of any kind
• Exposure to pressure, extreme temperatures (outside of -20ºC to
45ºC), and submersion in water. This product is not water resistant
or waterproof, it is shock resistant but not shock proof, and its
performance can be hindered in extreme temperatures.
• Installation and operation contrary to the instructions which come with
the product, including misuse ,abuse, and negligence.
• Cosmetic damage.
• Modification of or to any part of the product.
This warranty does not cover any product for which the factory applied
serial number has been altered or removed or any damage due to improper
maintenance. This warranty is valid in any countries SIS sells the product or is
legally represented. SIS reserves the right to determine if the product is within
the guidelines of this warranty. SIS, at its sole discretion may service, repair,
or replace this product after determining the cause of failure. For Returns:
Original sales receipt must be produced for any warranty service, and a Return
Merchandise Authorization (RMA) number must be obtained from customer
service at 1-805-480-9800 prior to returning product. Products will not be
accepted without an RMA.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, SIS SHALL NOT
BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND CAUSED BY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ON THIS PRODUCT.
WA R R A N T Y
STABLE IMAGING SOLUTIONS, LLC. DISCLAIMER
All purchasers, users, and any or all parties involved or engaging in the use of Stable
Imaging Solutions, LLC. (“SIS”) products agree to the following:
• SIS does not promote or endorse careless and or dangerous actions when
using its products.
• SIS is not liable for any use or misuse of SIS products in applications other
than those for which it was designed.
• SIS does not take any responsibility in relation to the use of our products or
any video captured that may be considered illegal.
• SIS is not responsible for any illegal actions taken while recording, attempting to record, or editing video that was captured with our products.
• SIS products primary purpose is for recording legal action sports or any
other activities as seen by all Local, State, Federal, and Country laws.
• SIS camera accessories, including mounts, lanyards and other accessory
items are provided as attachment options and are sold as is. They must be
used with extreme caution and care when the camera is mounted to a helmet, person, or any kind of property during any activity in the event that it
comes loose or stays put in which it could cause harm, injury, or death.
• SIS is indemnified from consequential or indirect loss, damage, injury, or
death resulting from the use of SIS products.
• All trademarks and registered trademarks mentioned herein are recognized
as the property of their respective holders.
Replay XD®, Replay XD RePower 4400 is a product of Stable Imaging Solutions,
LLC. in California.
www.Replayxd.com
©2012 Stable Imaging Solutions, LLC., Replay XD® All rights reserved.
D I S CL A I M E R
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Radio and TV Interference This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the
specifications in Part 15 of FCC rules. These specifications are designed
to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The supplied interface cable must be used with the equipment in order to
comply with the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
Canadian ICES-003 Statement
This Class B digital apparatus complies with Canadian ICES-003.
RoHS
This device complies with European Union’s ROHS directive 2002/95/EC
and similar regulations that may be adopted by other European countries
for European Sales.
CE Certified
CO M P L I A N CE
Replay XD a fine brand of Stable Imaging Solutions, LLC.
Sales & Technical Support:
Phone: 1-805-480-9800
Sales: [email protected]
Support: [email protected]
Office & Administration:
Monday–Friday, 8am–5pm (PST)
Corporate Address:
Stable Imaging Solutions, LLC.
3709 Old Conejo Road
Newbury Park, CA 91320
REV. 2012.4.1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement