Manual
402
Contents
EC DECLARATION OF CONFORMITY FOR MACHINES ....................................................................................
p. 2
WARNINGS FOR THE INSTALLER .......................................................................................................................
p. 2
1.
DESCRIPTION AND TECHNICAL SPECIFICATIONS ....................................................................................
p. 3
1.1.
DIMENSIONS ................................................................................................................................
p. 3
2.
ELECTRIC DEVICES (standard system) ....................................................................................................
p. 3
3.
INSTALLING THE AUTOMATED SYSTEM ......................................................................................................
p. 4
3.1.
PRELIMINARY CHECKS ................................................................................................................
p. 4
3.2.
INSTALLATION DIMENSIONS ........................................................................................................
p. 4
3.2.1. GENERAL RULES FOR DETERMINING THE INSTALLATION DIMENSIONS ............................
p. 4
INSTALLATION OF THE OPERATORS .............................................................................................
p. 4
START-UP ....................................................................................................................................................
p. 6
4.1.
ADJUSTING THE ANTI-CRUSHING SYSTEM ..................................................................................
p. 6
5.
FINAL OPERATIONS ...................................................................................................................................
p. 7
6.
AUTOMATED SYSTEM TEST .........................................................................................................................
p. 7
7.
MANUAL OPERATION ...............................................................................................................................
p. 7
8.
RESTORING NORMAL OPERATION MODE ................................................................................................
p. 7
9.
MAINTENANCE ..........................................................................................................................................
p. 7
10. REPAIRS .....................................................................................................................................................
p. 7
11. TROUBLE SHOOTING .................................................................................................................................
p. 8
3.3.
4.
Read this instruction manual to the letter before you begin to install the product.
Symbol
highlights notes that are important for people’s safety and for the good condition of the automated system.
Symbol
draws your attention to the notes about the product’s characteristics or operation.
FAAC S.p.A.
Via Benini, 1
40069 Zola Predosa (BO) - ITALIA
Tel.: 051/61724 - Fax: 051/758518
www.faac.it
732143 Rev.A.
1
EC DECLARATION OF CONFORMITY FOR MACHINES
(DIRECTIVE 98/37/EC)
Manufacturer:
FAAC S.p.A.
Address:
Via Benini, 1 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that:
402 mod. operator,
• is built to be integrated into a machine or to be assembled with other machinery to create a machine under the
provisions of Directive 98/37/EC;
• conforms to the essential safety requirements of the following EEC directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
and also declares that it is prohibited to put into service the machinery until the machine in which it will be
integrated or of which it will become a component has been identified and declared as conforming to the
conditions of Directive 98/37/EC.
Bologna, 01 January 2005
The Managing Director
A. Bassi
WARNINGS FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
13) Make sure that a differential switch with threshold of 0.03 A is fitted
upstream of the system.
1) ATTENTION! To ensure the safety of people, it is important that you read
all the following instructions. Incorrect installation or incorrect use of
the product could cause serious harm to people.
14) Make sure that the earthing system is perfectly constructed, and
connect metal parts of the means of the closure to it.
2) Carefully read the instructions before beginning to install the product.
15) The safety devices (EN 12978 standard) protect any danger areas
against mechanical movement Risks, such as crushing, dragging,
and shearing.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach
of children as such materials are potential sources of danger.
4) Store these instructions for future reference.
16) Use of at least one indicator-light (e.g. FAACLIGHT ) is recommended
for every system, as well as a warning sign adequately secured to the
frame structure, in addition to the devices mentioned at point “15”.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could
compromise the good condition/operation of the product and/or be a
source of danger.
17) FAAC declines all liability as concerns safety and efficient operation
of the automated system, if system components not produced by
FAAC are used.
6) FAAC declines all liability caused by improper use or use other than that
for which the automated system was intended.
18) For maintenance, strictly use original parts by FAAC.
7) Do not install the equipment in an explosive atmosphere: the presence
of inflammable gas or fumes is a serious danger to safety.
19) Do not in any way modify the components of the automated system.
8) The mechanical parts must conform to the provisions of Standards EN
12604 and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal
regulations.
20) The installer shall supply all information concerning manual operation
of the system in case of an emergency, and shall hand over to the
user the warnings handbook supplied with the product.
9) FAAC is not responsible for failure to observe Good Technique in the
construction of the closing elements to be motorised, or for any
deformation that may occur during use.
22) Keep remote controls or other pulse generators away from children,
to prevent the automated system from being activated involuntarily.
10) The installation must conform to Standards EN 12453 and EN 12445.
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal
regulations.
24) The user must not attempt any kind of repair or direct action whatever
and contact qualified personnel only.
21) Do not allow children or adults to stay near the product while it is
operating.
23) Transit through the leaves is allowed only when the gate is fully open.
25) Maintenance: check at least every 6 months the efficiency of the
system, particularly the efficiency of the safety devices (including,
where foreseen, the operator thrust force) and of the release devices.
11) Before attempting any job on the system, cut out electrical power .
12) The mains power supply of the automated system must be fitted with an
all-pole switch with contact opening distance of 3mm or greater. Use
of a 6A thermal breaker with all-pole circuit break is recommended.
26) Anything not expressly specified in these instructions is not permitted.
2
402 AUTOMATION SYSTEM
These instructions apply to the following models:
1.1.
DIMENSIONS
402 CBC - 402 SBS
The FAAC 402 automated system for swing leaf gates consists of
an enbloc composed of an electric pump and a hydraulic piston
which transmits drive to the leaf.
The model with a hydraulic locking does not require installation of
electric locks, as it guarantees mechanical locking of the leaf when
the motor is not operating.
The model without a hydraulic locking, requires the installation of
electric locks to ensure the leaf is mechanically locked.
Fig. 2
The 402 automated systems were designed and built to automate
swing leaf gates. Do not use for any other purpose.
1.
DESCRIPTION AND TECHNICAL SPECIFICATIONS
OPERATOR TYPE
CBC
A
B
C
OVERALL DIMENSIONS
DISTANCE BETWEEN ATTACHMENTS
EFFECTIVE STROKE
SBS
959 mm. 959 mm.
664 mm. 664 mm.
240 mm.
40 mm.
2.
ELECTRIC DEVICES (standard system)
Fig. 3
Electric motor
Hydraulic piston
Cylinder
By-pass valves
Gerotor pump
Front attachment
Housing
Rear attachment
Fig. 1
Tab. 1: Technical specifications of “402 Operator”
MODEL
Power supply voltage
402 CBC
402 SBS
230 Vac(+6%-10%) 50 (6o) Hz
Rod extension speed
1.3 cm/s
Pump flow rate
1 l/min
0.75 l/min
1 cm/s
Traction and thrust force
0-500 daN
0-690 daN
Operators mod. 402
(provide a connector block for each operator)
Photocells
Electronic control unit
Key operated push-button T 10
Radio receiver
Flashing light
Electric lock (if necessary)
Operating ambient
temperature
-40°C - +55°C
Absorbed power
220 W
Absorbed current
1A
Motor rotation speed
1400 rpm
Motor winding temperature
120°C
Weight
6.5 kg
Type of oil
Use frequency
2)
FAAC HP OIL
Protection class
Single leaf max length
1)
IP 55
1,80 m
3,00 m
55 (cycles/hour)
3
To lay the electrical cables, use adequate rigid
and/or flexible pipes.
Always separate the connection cables of the
low voltage accessories from the 230 V power
cables. Use separate sheaths to avoid any type
of interference.
3.
3.2.1.
INSTALLING THE AUTOMATED SYSTEM
3.1.
PRELIMINARY CHECKS
If the dimensions indicated in table A or B cannot be executed,
the following must be considered in order to determine different
measurements:
- to obtain 90° opening of the leaf: a + b = c.
To ensure a correctly operating automated system, the structure
of the existing gate or gate to be built must satisfy the following
requirements:
•
Max length of leaves according to the dimensions of Table
1 on page 3.
•
•
A strong and rigid leaf structure.
Smooth, uniform leaves movement, without any irregular friction
during the entire travel;
• Existing hinges in good condition.
• Travel limit mechanical stops must be provided.
We advise you to carry out the metalwork jobs before installing
the automated system.
The condition of the structure directly influences the reliability and
safety of the automated system.
3.2.
GENERAL RULES FOR DETERMINING THE
INSTALLATION DIMENSIONS
-
to obtain over 90° opening of the leaf: a + b < c.
-
lower a and b dimensions will result in higher speeds. We advise
you to observe the current legal regulations;
-
limit the difference of the a and b dimensions to within 40 mm:
higher differences will considerably vary speed during the
opening and closing motion;
-
for reasons of operator dimensions, the minimum Z dimension
is 50 mm (Fig. 4);
-
if the pilaster dimensions or the position of the hinge (dimension
d) do not make it possible to contain dimension a to the
required size, a niche must be made in the pilaster as shown in
Fig. 5;
-
dimension a must always be larger than dimension E.
INSTALLATION DIMENSIONS
Fig. 4
dimensions in mm
(1) Length of dimension “a” - 50 mm.
(2) Length of dimension “b” + 100 mm.
3.3.
Table A: Recommended dimensions for standard operators
Opening
angle
90°
110°
a
(mm)
120
100
b
(mm)
120
100
c(*)
(mm)
240
240
1)
d(**)
(mm)
70
50
(*) Rod effective stroke (**) maximum dimension
c = The effective rod stroke is shorter than the maximum stroke, in
order to prevent the rod from reaching its stop point
internally, during the opening and closing stages.
4
Fig. 5
INSTALLATION OF THE OPERATORS
Fasten the rear attachment on the pilaster, following the
indications in Table A. Modify, if necessary, the length of the
supplied attachment.
Attention: To avoid compromising good operator
functionality, we recommend you to respect the indicated
dimensions.
• For iron pilasters, accurately weld the rear attachment
(ref., Fig. 6) directly on the pilaster.
• For masonry pilasters, select one of the following solutions:
A) appropriately lay a walling-in plate and then
accurately weld the rear attachment.
B) secure, with screws and expansion plugs, the rear
attachment plate (ref. a, Fig.6) to the pilaster and
then accurately weld the rear attachment to the
plate as shown in Fig. 6.
2)
Secure the operator to the rear attachment with the
supplied screws (Fig. 6), taking care to position the operator
with the BY-PASS screws facing up and the consequent
RELEASE screw facing the ground.
3)
Release the operator (see chapter 7).
4)
Fully remove the rod to its stop point and make it recede
by about 5 mm (Fig.7).
5)
Relock the operator (see chapter 8).
Fig. 8
Fig. 6
10)
Definitively weld the front attachment on the leaf.
To do this, temporarily release the operator from the front
attachment to prevent welding waste from damaging it
(Fig.10).
A)
B)
We advise you to grease all the securing pins of
the attachments.
If welding is impossible, the plates of the front and
rear attachments are designed to be secured with
screws if necessary.
Fig. 7
Fig. 9
6)
Fit the front attachment onto the rod (Fig. 8)
7)
Close the gate leaf and, keeping the operator perfectly
horizontal, find the position of the front attachment (Fig. 9)
on the leaf.
8)
Fig. 10
Provisionally fix the front attachment on the leaf with two
weld spots, protecting the rod against any welding waste.
If the gate structure does not permit the
attachment to be firmly fastened, take action on
the structure, creating a solid support base.
9)
Release the operator and manually check if the gate is
free to open completely stopping on the travel limit
mechanical stops and if leaf movement is good and
friction- free.
5
Fig. 11
11)
Prepare the protective housing and fit it on the operator
as shown in Fig. 11.
A) Insert the two anti-vibration spacers onto the front
flange.
B) Introduce the housing, pressing it firmly on the rear cover
.
C) Secure the housing with the self-tapping screw .
D) Fit the front cover on the housing and fasten it with
FIX plug .
12)
Fit the electric cable bend guard (ref., Fig. 11A).
13)
Re-lock the operator and make the electrical connections
of the selected electronic control unit following the relevant
instructions.
4.
Fig. 11A
START-UP
- Connect the power cable of the operator (Fig.11A).
- Fasten the screws (ref. , Fig. 11A).
4.1.
To adjust the torque limiters, consult Standards EN 12453 and EN
12445 for EU member countries and current legal regulations in
the other countries.
ADJUSTING THE ANTI-CRUSHING SYSTEM
The 402 automated system has an anti-crushing safety device
which limits the operator's force if an obstacle is encountered while
the gate is moving.
To adjust the intervention threshold of the anti-crushing system,
turn the By-Pass screws on the flange (FIG.12).
- the red screw controls closing movement torque.
- the green screw controls opening movement torque.
To increase torque, turn the screws clockwise.
To reduce torque, turn the screws anti-clockwise.
When you have finished adjusting, apply the label with the FAAC
logo, using the self tapping screws (FIG.12).
Fig. 12
6
5. FINAL OPERATIONS
Fig. 15
Finish the installation operations as follows:
- Remove the breather screw (Fig.13, ref. )
Fig. 13
LOCK
6.
AUTOMATED SYSTEM TEST
9.
When you have finished installing, apply the danger signal sticker
on the side of the operator so that it is clearly visible (Fig.14).
Run an accurate functional check of the automated system and
of all the accessories connected to it, especially the safety devices.
Hand the “User’s Guide” to the Client, explain correct operation
and use of the operator, and indicate the potentially dangerous
areas of the automated system.
UNLOCK
MAINTENANCE
Run a functional check of the system at least every 6 months, with
special attention to the efficiency of the safety and release devices
(Including the thrust force of the operator), and to perfect
operation of the gate hinges.
Also, periodically check quantity of oil inside the tank.
Oil level check instructions:
- Cut power to the system.
- Release the operator from the front and rear attachments.
- Position the operator vertically, with the rear flange high up.
- Remove the oil filling plug.
- Insert a screwdriver until it comes into contact with the electric
motor as shown in Fig. 16.
- Remove the screwdriver and check oil level as shown in Fig. 16.
USE ONLY FAAC HP FLUID OIL
Periodically check correct adjustment of the anti-crushing safety
device (BY-PASS) and the efficiency of the release system to allow
manual operation (see relevant paragraph).
The safety devices installed on the system must be checked every
6 months.
Fig. 16
Fig. 14
7.
MANUAL OPERATION
If the gate has to be moved manually due to a power cut or fault
of the automated system, use the release device as follows:
- Insert the triangular key on the release screw located in the lower
part of the flange (Fig.15).
- Turn the release key anti-clockwise for about two turns.
- Open or close the leaf manually.
8.
RESTORING NORMAL OPERATION MODE
To prevent an involuntary pulse from activating the operator during
the manoeuvre, cut power to the system before re-locking the
operator.
- To re-lock the operator, turn the key clockwise until it stops (Fig.
15).
- Lastly, remove the key and restore the power supply to the system.
10. REPAIRS
For any repairs, contact FAAC’s authorised Repair Centres.
7
11. TROUBLESHOOTING
The following table will help you identify and solve some particular conditions.
CONDITION
A
Gate not moving.
B
Gate moving slowly.
C
Gate moving jogwise.
D The operator is losing oil from the breather screw.
E
The leaves stop at slow-down.
F
Gate speed not constant.
SUGGESTION
-
Check if mains power is supplied.
Make sure that the operator is not unlocked. (chapter 8.).
Check the adjustment of the anti-crushing system (paragraph 4.1).
Check oil level inside the tank. (chapter 9 - Fig. 16).
Check the connection and operation of the thrust capacitor.
Check the efficiency of the electronic control unit.
- Check the adjustment of the anti-crushing system (paragraph 4.1).
- Make sure that you have removed the breather screw (chapter 5).
- Run some complete gate opening and closing cycles, in order to release any
air inside the piston.
- An initial, minimum oil leak is normal. A larger leak may occur if the operator is
not fitted in a perfectly horizontal plane. If the oil leak does not stop soon, we
advise you to visit an authorised repair centre.
- Check the adjustment of the anti-crushing system (paragraph 4.1).
- Incorrect installation dimensions (paragraph 3.2).
Notes
8
FAAC402
Attuatore
SERIAL NUMBER
______________________________________________________________
______________________________________________________________
_________________________________________________________________________________________________________________________
______________________________________________________________
________________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
Indication of residual risks and of foreseeable improper use
Other device
Other device
Flashing lamp
Radio control
Control device 2
Control device 1
Pair of photocells 2
Pair of photocells 1
Safety device 2
Safety device 1
MODEL
PART
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
7
8
9
10
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
Description of job
6
Date
_____________________________________________
_____________________________________________
_____________________________________________
5
4
3
2
1
No.
MAINTENANCE REGISTER
Installation technician________________________________________________
Customer___________________________________________________________________
Type of system ________________________________________________________
Serial number_________________________________________________________
Installation date______________________Activation________________________
System configuration
9
19
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Customer
Technician
Signatures
USER’S GUIDE
AUTOMATED SYSTEM 402
Read the instructions carefully before using the product and store
them for future use
The other models, without a hydraulic locking always require one
or more electric locks to ensure the leaf is mechanically locked.
Leaves of up to 3 mt can be automated depending on the
selected model.
The functioning of the operators is controlled by an electronic
control unit, housed in an enclosure with adequate degree of
protection against atmosphere agents.
The leaves are normally closed.
When the electronic control unit receives an opening command
from the radio control or any other pulse generator, it activates
the hydraulic appliance which rotates the leaves until they reach
the opening position to allow access.
If automatic mode was set, the leaves close automatically after
selected pause time has elapsed.
If the semi-automatic mode was set, a second pulse must be sent
to close the leaf again.
A stop pulse (if supplied) always stops movement.
For details on the behaviour of the automated system in different
function logics, consult the installer.
Automated systems include safety devices (photocells) that
prevent the leaves from moving when there is an obstacle in the
area they protect.
The 402 automated system is supplied standard with a hydraulic
anti-crush protection safety device (BY-PASS) which limits the
torque transmitted to the leaves.
The warning-light indicates the current leaf movement.
GENERAL SAFETY REGULATIONS
If correctly installed and used, the 402 automated system ensures
a high degree of safety.
Some simple rules on behaviour can prevent accidental trouble:
- Do not pass between the leaves when they are moving. Wait
for the leaves to open fully before passing through them.
- Do not, on any account stay in between the leaves.
- Do not stand near the automated system, and do not allow
children, persons or things to do so, especially when it is
operating.
- Keep remote controls or other pulse generators away from
children, to prevent the automated system from being
activated involuntarily.
- Do not allow children to play with the automated system.
- Do not willingly obstruct leaves movement.
- Prevent any branches or shrubs from interfering with leaves
movement.
- Keep indicator-lights efficient and easy to see.
- Do not attempt to activate the leaves by hand unless you have
released them.
- In the event of malfunctions, release the leaves to allow access
and wait for qualified technical personnel to do the necessary
work.
- When you have set manual operation mode, cut power to the
system before restoring normal operation.
- Do not in any way modify the components of the automated
system.
- Do not attempt any kind of repair of direct action whatever
and contact qualified personnel only.
- At least every six months: arrange a check by qualified
personnel of the automated system, safety devices and earth
connection.
MANUAL OPERATION
If the gate has to be moved manually due to a power cut or fault
of the automated system, use the release device as follows:
- Insert the triangular key on the release screw located in the lower
part of the flange (Fig.1).
- Turn the release key anti-clockwise for about two turns.
- Open or close the leaf manually.
DESCRIPTION
These instructions apply to the following models:
402 CBC - 402 SBS.
RESTORING NORMAL OPERATION MODE
The FAAC 402 automated system for swing leaf gates consists of a
hydraulic enbloc composed of an electric pump and a hydraulic
piston which transmits drive to the leaf.
The models with a hydraulic locking do not require installation of
an electric lock, as they guarantee mechanical locking of the leaf
when the motor is not operating.
To prevent an involuntary pulse from activating the operator during
the manoeuvre, cut power to the system before re-locking the
operator.
- To re-lock the operator, turn the key clockwise until it stops (Fig.
1).
- Release the operator from the front and rear attachments.
OPEN
UNLOCK
LOCK
Fig. 1
10
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi
ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per
qualsiasi altra esigenza di carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present manual are not binding. FAAC reserves the right, whilst
leaving the main features of the equipments unaltered, to undertake any modifications it holds necessary for either
technical or commercial reasons, at any time and without revising the present publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. FAAC se réserve le droit d’apporter à
tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. FAAC behält sich das Recht
vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezug auf die
Neufassung der vorliegenden Anleitungen, technisch bzw. konstruktiv/kommerziell bedingte Verbesserungen vorzunehmen.
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. FAAC se reserva el derecho,
dejando inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que considere oportunas para el perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.
De beschrijvingen in deze handleiding zijn niet bindend. FAAC behoudt zich het recht voor op elk willekeurig moment de
veranderingen aan te brengen die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke
andere productie- of commerciële eisen, waarbij de fundamentele eigenschappen van de apparaat gehandhaafd
blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.
FAAC S.p.A.
Via Benini, 1
40069 Zola Predosa (BO) - ITALIA
Tel. 0039.051.61724 - Fax. 0039.051.758518
www.faacgroup.com
732143 - Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising