- IDEC USA

- IDEC USA
Automation & Sensing
OI Touchscreens
Selection Guide........................................... 166
PS6R Standard Series................................. 167
Part Numbers................................................. 167
Specifications................................................. 168
Dimensions.................................................... 170
PLCs
PS5R-V Series............................................. 174
Part Numbers................................................. 174
Specifications................................................. 175
Dimensions.................................................... 178
Automation Software
PS5R Slim Line Series................................. 182
Part Numbers................................................. 183
Specifications................................................. 184
Dimensions and Terminal Markings.............. 186
PS5R Standard Series................................. 188
Part Numbers................................................. 188
Specifications................................................. 189
Dimensions.................................................... 192
Power
Supplies
Power Supplies
PS3X Series................................................. 193
Part Numbers................................................. 193
Specifications................................................. 194
Dimensions.................................................... 196
Safety Precautions......................................... 198
Sensors
Communication
www.IDEC.com/powersupply
Barriers
Table of Contents
LED Lighting - Pg. 1
Automation & Sensing - Pg. 21
Safety - Pg. 281
Switching & Controls - Pg. 483
Index - Pg. 1039
Power Supplies
OI Touchscreens
Selection Guide
Selection Guide
Series
PS6R
PS5R-V
PS5R Slim Line
PS5R
PS3X
PS3L
167
174
182
188
193
Visit www.IDEC.com/
powersupply
PLCs
Appearance
Page
Automation Software
Housing
Metal
Power Supplies
Metal
Direct or DIN Rail mount
Panel or bracket mount
DIN Rail
Wattage Range
120W to 480W
7.5W to 240W
10W to 240W
7.5W to 480W
15W to 100W
10W to 300W
Input Voltage
100 to 240 V A,
110 to 350V DC
85 to 264V AC,
100 to 370V DC
85 to 264 V AC,
100-370 V DC (100-350V
DC, 120W & 240W)
85 to 264V AC,
105 to 370V DC
85 to 264V AC,
120 to 375V DC
85 to 264V AC,
105 to 370V DC
5V DC
2A
1.5A, 2.0A
2.0A
1.5A, 2.5A
3A, 5A, 12A, 16A
2A, 3A, 6A
12V DC
1A
0.6A, 1.3A, 2.5A
1.2A, 2.5A
0.6A, 1.2A, 2.5A
1.3A, 2.1A, 4.2A, 6A, 8.5A
0.90A, 1.4A, 2.5A, 4.3A,
8.5A, 13A
24VDC
5A, 10A, 20A
0.3A, 0.65A, 1.3A,
2.5A, 3.75A, 5.0A,
10.0A
0.65A, 1.3A, 2.5A, 3.75A,
5A, 10A
0.30A, 0.60A, 1.3A, 2.1A,
3.1A, 4.2A, 5A, 10A, 20A
0.63A, 1.1A, 2.2A, 3.2A,
4.5A
0.50A, 0.70A, 1.3A,
2.2A, 4.5A, 6.5A, 12.5A
up to 77%
69%
69%
77%
70-75%
up to 85%
75%, 78%
73% to 75%
81% to 82%
74% to 80%
up to 90%
80% to 84%
75% to 91%
82% to 84%
78% to 82%
Output
Current
Ratings
Typical
Efficiency
12V DC
up to 93%
24V DC
DIN Rail or surface mount
+/-10% (+/- 5% for
90W)
Voltage Adjustments
+/-10%
Ripple Voltage
1.5%peak to peak
max (including noise)
-
Overvoltage
Protection (input)
120%
-
Overcurrent
Protection (output)
105 to 120% (auto
reset)
Operating Temperature
-10˚ to +70°C (14° to
140°F)
Termination
105% minimum (101%
for 90W), auto reset
-25°C to +75°C
+/-10% (V.ADJ control on front)
2% peak to peak max (including noise)
120% or more, auto reset
105% min shutdown
120% typical
-10° to +70°C (14° to 140°F)
M3.5 phillip/slotted, spring loaded, captive (fingersafe)
ANSI/ISA-12.12.01-2011 Listed
File#E234997
ANSI/ISA-12.12.01-2011 Listed
File#E234997
–
160mV maximum
115% typical
120% typical
-10° to +85°C
-10° to +60°C (14° to
140°F)
105% minimum (Zener or
auto reset)
M3 or M3.5
UL508 Listed
File #E177168
Communication
Metal
Mounting
5V DC
Sensors
Plastic
DIN Rail or surface
mount; 6 direction
IEC Style screw
terminals (fingersafe)
UL508 Listed
File #E177168
ANSI/ISA-12.12.01-2011 Listed
File#E234997
Cert No.
BL980213332392
Approvals
Barriers
(SEMI F47 120W &
240W only)
166 www.IDEC.com
1705151126
Power Supplies
PS6R Series
OI Touchscreens
PS6R Series Switching Power Supplies
Expandable and space-saving switching power supplies. High efficiency reduces operation costs.
PLCs
• 93% efficiency
• Plug-in output modules for additional output voltages
• Plug-in branch terminal module for additional terminals
• Power Range: 120W, 240W, 480W
• Input voltage: 100 to 240V AC
(voltage range: 85 to 264V AC/110 to 350V DC)
• Up to 70ºC (158ºF) operating temperature
• DC low LED indicator and output contact
• The terminals are captive spring-up screws. Ring or fork
terminals can be used.
• Finger-safe construction prevents electric shocks.
• Panel mount bracket and side-mount panel mounting
bracket. Can be attached to a DIN rail or directly to a panel
surface.
• RoHS compliant
• UL listed for Class 1, Division 2 Hazardous Locations
• Meets SEMI F47 Sag Immunity
• ABS Certified for maritime use
Applicable Standards
Mark
UL508
CSA C22.2 No. 107.1
C
US
LISTED
Automation Software
60mm
37mm
85mm
File No. or Organization
UL/c-UL Listed
File No. E177168
TÜV SÜD
EN60950-1
EN50178
EN61204-3
Power Supplies
EU Low Voltage Directive
EMCD
Part Numbers
PS6R
Output
Capacity*
Accessories
Part No.
PS6R-F24
240W
PS6R-G24
480W
PS6R-J24
Output
Current
5A
85 to 264V AC
21.6 to 26.4V
Item
Output Voltage Expansion
Module Note 1
10A
20A
*Output voltage × output current = output capacity
Part No.
Note
PS9Z-6RM1
Output: +5V, 2A, 10W
PS9Z-6RM2
Output: +12V, 1A, 12W
PS9Z-6RM3
Output: +5V, 1A/-5V, 1A, 10W
PS9Z-6RM4
Output: +15V, 0.4A/-15V, 0.4A, 12W
PS9Z-6RM5
Output: +5V, 1A/+12V, 0.5A, 11W
PS9Z-6RM6
Output: +12V, 0.5A/-12V, 0.5A, 12W
PS9Z-6RS1
Additional screw terminals for wiring:
2 + terminals / 2 - terminals
Sensors
120W
Input Voltage
Output
Voltage
Branch Terminal Module Note 2
PS9Z-6R1F
DIN Rail End Clip
BNL6
PS9Z-6R2F
BNDN1000
Communication
Panel Mounting Bracket
Side-mount Panel Mounting
Bracket
DIN Rail
Supplied with M3 × 6 countersunk
mounting screws
1,000mm
1. When using an output voltage expansion module, reduce 1A from the output current of PS6R.
2. When using a branch terminal module, the total voltage/current of PS6R and the branch terminal
module should not exceed the rated current/voltage of PS6R
Barriers
120W shown with Branch Terminal module attached.
1705151126
800-262-IDEC (4332) • USA & Canada
167
Power Supplies
OI Touchscreens
PS6R Series
Specifications
PS6R
Part No.
PS6R-F24
Input Voltage
Frequency
100V AC
230V AC
100V AC
Inrush
Current
230V AC
120V AC
Leakage
Current
230V AC
100V AC
Efficiency
(Typical)
230V AC
Power Factor 100V AC
(Typical)
230V AC
Rated Voltage/Current
Adjustable Voltage Range
Output Holding Time
Start Time
Rise Time
Output
Automation Software
PLCs
Input
Input Current
Total Fluctuation
Regulation
Dielectric Supplementary
Strength
Functions
Power Supplies
Sensors
PS6R-J24
±5% max.
Input Fluctuation
Load Fluctuation
Temperature Change
Ripple (including noise)
Communication
PS6R-G24
100 to 240V AC
(Voltage range: 85 to 264V AC/110 to 350V DC) (Load ≤ 80% at 85 to 100V AC, 110 to 140V DC) Note 1
50/60Hz
1.4A typ
2.7A typ
5.5A typ.
0.7A typ
1.2A typ
2.3A typ.
9A max. (Ta=25ºC, 100V AC cold start)
20A max. (Ta=25ºC, 230V AC cold start)
0.5mA max.
1mA max.
90%
90%
91%
90%
91%
93%
0.99
0.99
0.98
0.96
0.97
0.97
24V/5A
24V/10A
24V/20A
±10%
20ms min. (at rated input and output)
800ms max. (at rated input and output)
200ms max. (at rated input and output)
0.4% max.
0.6% max.
0.05%/oC max. (–10 to +60ºC)
1% p-p max. (0 to +60ºC)
1.5% p-p max. (–10 to 0ºC)
Overcurrent Protection
105 to 120% (auto reset) (output current when voltage drops by 5%)
Overvoltage Protection
Output off at 120% Note 2
Operation Indicator
LED (green)
Voltage Low Indication
LED (amber)
Between input and output terminals
Between input and ground terminals
Between output and ground terminals
3000V AC, 1 minute
2000V AC, 1 minute
500V AC, 1 minute
100MΩ
min.
500V
DC
megger
(between
input
and output terminals/between input and ground terminals)
Insulation Resistance
(at room temperature and normal humidity)
Operating Temperature
–10 to +70ºC (no freezing) Note 3
Operating Humidity
20 to 90% RH (no condensation)
Storage Temperature
–25 to +75ºC (no freezing)
Storage Humidity
20 to 90% RH (no condensation)
10 to 55 Hz, amplitude 0.375 mm (0.187mm using PS9Z-6R1F)
Vibration Resistance
2 hours each in 3 axes, 6 directions
Shock Resistance
300 m/s2 (150 m/s2 when using a PS9Z-6R1F panel mounting bracket)
EMI
EN61204-3 (Class B)
EMC
EMS
EN61204-3 (industrial)
Degree of Protection
IP20 (IEC 60529)
Weight (approx.)
630g
960g
1400g
Terminal Screw
M3.5 (See last page for wire sizes)
1. DC input voltage is not subjected to safety standards.
3. See the output derating curves.
2. One minute after the output has been turned off, turn on the input again.
Easily Expandable
Branch Terminal Module
Output Voltage
Expansion Module
Two terminals can be added.
No wiring is required, reducing
installation space.
Barriers
In addition to the standard 24V
output, additional 5, 12, and 15V
outputs can be added.
168 www.IDEC.com
1705151126
Power Supplies
PS6R Series
Accessories (For use with PS6R)
PS9Z-6RM1
Input Voltage
Output Capacity
10W max.
12W max.
5V/2A
12V/1A
Rated Voltage/Current
Supplementary
Functions
PS9Z-6RM4
24V DC
10W max.
12W max.
±5V 2A
±15V 0.4A
11W max.
5V/1A,
12V/0.5A
100mV max.
150mV max.
PS9Z-6RS1
12W max.
—
±12V 0.5A
24V/10A max. Note 1
—
—
—
0.05%/max. (–10 to +60°C)
100mV max., 150mV max.
Overcurrent Protection
105% (auto reset)
Overvoltage Protection
Output off at 120%
—
Shock Resistance
EMI
EMS
Power Supplies
Safety Standards
Degree of Protection
Weight (approx.)
Terminal Screw
Automation Software
–10 to +70°C (no freezing) Note 2
20 to 90%RH (no condensation)
–25 to +75°C (no freezing)
20 to 90% RH (no condensation)
10 to 55 Hz, amplitude 0.375 mm, 2 hours each in 3 axes, 6 directions (in combination with PS6R-J24)
300 m/s2 (150 m/s2 when using a PS9Z-6R1F panel mounting bracket),
3 shocks each in 6 axes (in combination with PS6R-J24)
EN61204-3 (Class B) (in combination with PS6R-24)
—
EN61204-3 (industrial) (in combination with PS6R-24)
UL508 (Listing), CSA C22.2 No.107.1, IEC/EN60950-1, EN50178 (in combination with PS6R-24)
IP20 (IEC 60529)
90g
30g
M3.5 (See last page for wire sizes.)
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Vibration Resistance
EMC
Branch Terminal Module
PS9Z-6RM5 PS9Z-6RM6
Not available
±5% max.
200 ms max. (at rated input and output)
0.5% max.
1.0% max.
Regulation
Output
PS9Z-6RM3
PLCs
Adjustable Voltage Range
Voltage Accuracy
Start Time
Input Fluctuation
Load Fluctuation
Temperature
Change
Ripple (including
noise)
PS9Z-6RM2
OI Touchscreens
Output Voltage Expansion Module
Part No.
1. Ensure that the current does not exceed the rated current of the PS6R.
2. See the output derating curves.
96
Operates without derating
at 0 to 60ºC
94
PS6R-J24
Competitor A
Competitor B
Efficiency (%)
92
Operates at –10 to 70ºC
90
88
86
84
82
0
10
20
30
40
50
60
70
80
Operating Temperature (°C)
50
100
150
200
250
Communication
100
90
80
70
60
50
40
30
20
10
0
–10
Energy-saving 93% Efficiency (480W)
Sensors
Output Current (%)
Wide Operating Termperature Range
300
Input Voltage (V AC)
Easy Maintenance - LED Indicator
Status
Normal
Overload or Input
Voltage Low*
Output
short-circuit
Output
OFF
DC ON
(green LED)
Barriers
DC Low
(amber LED)
*The LEDs turn on when the input voltage drops.
1705151126
800-262-IDEC (4332) • USA & Canada
169
Power Supplies
Dimensions (mm)
PS6R-G24
PS6R-F24
PS6R-J24
125
4
125
A A
4
10-M3.5
Terminal Screws
A A
125
4
9.3
A A
9.3
8 - M3.5
Terminal Screws
6 - M3.5
Terminal Screws
PS9Z-6R1F Panel Mounting Bracket
A
44.9
35.3
125
A
130.6
145
28
28
39
Panel cut-out
(Front view)
PS9Z-6R2F (Side-mount Panel Mounting Bracket)
When a PS9Z-6R2F is installed on PS6R
4-M4 or ø4-4.5 holes
56
(Side view)
4-M4 or 4-ø4.5 holes
C
B
D
148.6
138.5
148.6
56
When using a PS9Z-6RM*
Output Voltage Expansion Module
Panel cut-out
(Front view)
(Side view)
Mounting Screws
(M3 × 6 countersunk screw)
When using a PS9Z-6RS1
Branch Terminal Module
Dimension Table
Mounting
Screws
170 107.2
Mounting
Screws
27.8
9.6
A
B
C
D
E
PS6R-F24
–
39.3
29.5
29.5
58
PS6R-G24
10.5
62.3
29.5
31
81
PS6R-J24
23
87.3
29.5
31
106
34.4
53
59
59
Barriers
9.3
Communication
56
70
11.8
Sensors
138.5
11.8
Power Supplies
10
135
135
145
Automation Software
A = 9.5
When a PS9Z-6R1F is installed on PS6R
4-M4 or ø4-4.5 holes
28
3.8
A A A A A A
85
A = 9.5
4.5
60
106.5
35.3
125
106.5
3.8
A A A A
10
3.8
A = 9.5
4.5
37
4.5
PLCs
35.3
125
106.5
44.9
44.9
9.3
OI Touchscreens
PS6R Series
21
33.4
www.IDEC.com
E
1705151126
Power Supplies
PS6R Series
OI Touchscreens
Operating Instructions
ø3.6 min.(reference)
Applicable Crimp Terminal
The PS6R should be placed in a proper enclosure. It is designed to be
used with general electrical equipment and industrial electric devices.
6.6 max.
4 max.
Operation Notes
1. Output interruption may indicate blown fuses. Contact IDEC.
2. The PS6R contains an internal fuse for AC input. When using DC input,
install an external fuse or DC input. To avoid blown fuses, select a fuse in
consideration of the rated current of the internal fuse.
Rated Current of Internal Fuses
Internal Fuse Rated Current
PS6R-F24
4A
PS6R-G24
6.3A
PS6R-J24
10A
•Recommended tightening torque of the input and output terminals is 0.8N·m.
•The output voltage can be adjusted within ±10% of the rated output voltage
by using the V.ADJ control. Note that overvoltage protection may work when
increasing the output voltage.
•When large shocks or heavy vibrations on the PS6R are expected, the use of
DIN rail or PS9Z-6R2F side-mount panel mounting bracket is recommended.
Series Operation
The following series operation is allowed. Connect Schottky barrier diodes as
shown below. Output voltage expansion modules cannot be connected in series.
L
N
-- Avoid overload and short-circuit for a long period of time,
otherwise internal elements may be damaged.
-- DC input operation is not subjected to safety standards.
L
N
+V
–V
L
N
+V
–V
Load
L
N
L
N
+V
–V
L
N
+V
–V
Load
Load
Automation Software
Installation Notes
(b)
(a)
•The PS6R can be installed in the direction shown below only.
Select a Schottky diode in consideration of the rated current. The diode’s reverse
voltage must be higher than the PS6R’s output voltage.
Parallel Operation
Parallel operation is possible to increase the output capacity. Output voltage
expansion modules cannot be connected in series.
Up
L
N
When using PS9Z-6R1F
Panel Mounting Bracket
When using PS9Z-6R2F
Side-mount Panel Mounting
Bracket
Terminal Wire Size/No. of Wire
Input
PS6R-F24 Output
PS6R-G24
DC OK
Output
Input
Wire Type
18-14 AWG, 1-wire
18-14 AWG, 1-wire, (18 AWG - 7A,
16 AWG - 10A, 14 AWG - 15A)
22-14 AWG, 1-wire (stripped wire
length: 6 to 7mm)
18-14 AWG, 1-wire
12 AWG, 1-wire
PS9Z-6R0 Output
22-14 AWG, 1-wire (stripped wire
length: 6 to 7mm)
18-14 AWG, 1-wire (18 AWG - 7A,
16 AWG -10A, 14 AWG - 15A)
+V
–V
When increasing the capacity, observe the following.
1. Maintain the operating temperature below 40ºC.
2. Output cannot be connected directly in parallel operation. Connect a diode to
the output of each PS6R.
3. Output terminal voltage of both power supplies must be the same. Also,
maintain the voltage difference between the power supplies below 30mV.
4. Use load lines of the same diameter and length.
5. Set the output voltage higher for the amount of diode forward voltage drop.
6. Turn on the inputs at the same time.
7. Select a diode in consideration of:
Diode’s reverse voltage must be higher than the PS6R’s output voltage.
Diode’s current must be three times the PS6R’s output current. Provide a heat
sink for heat dissipation.
7.0 (0.8)
Communication
PS6R-J24 Output
L
N
Load
Copper
Solid/Stranded
18-14 AWG, 2-wire
Use the same size wire for each
terminal (18 AWG - 7A,
16 AWG - 10A, 14 AWG - 15A)
DC OK
Output
Torque,
in-ibs (N∙m)
+V
–V
Sensors
•Do not close the top and bottom openings of the PS6R to allow for heat radiation by convection.
•Maintain a minimum of 20mm clearance around the PS6R, except for the top
and bottom openings.
•When derating of the output does not work, provide forced air-cooling.
•Make sure to wire the ground terminal correctly.
•For wiring, use wires with heat resistance of 60ºC or higher.
Use copper wire of the following sizes. Wires of the following sizes must be
used to comply with UL508, CSA C22.2 No. 107.1.
L
N
Power Supplies
Vertical
Model
PLCs
Part No.
5.5 min.
Copper
Solid/Stranded
Use with UL-listed ring/
fork crimp terminal.
Copper
Solid/Stranded
—
7.0 (0.8)
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
171
Power Supplies
OI Touchscreens
PS6R Series
PS9Z-6RM3/M4/M6
Output Voltage Expansion Module
PS6R-6RM1/M2/M3
Output Voltage Expansion Module
PS6R-6RS1
Branch Terminal Module
PLCs
PS6R-J24
(PS6R-6RM5 shown)
PS6R-24/PS9Z-6RS1
Name
Voltage range: 85 to 264V AC/110 to 350V DC
Ground Terminal
Be sure to connect this terminal to a proper ground.
+V, –V
DC Output Terminals
+V: Positive output terminal
–V: Negative output terminal
VR.ADJ
Output Voltage Adjustment
Allows adjustment within ±10%. Turning clockwise increases the output voltage.
DC ON
Operation Indicator (green)
Lights on when the output voltage is on.
DC LOW
Output Low Indicator (Amber)
Lights on when the output voltage drops approximately 80% of the rated value.
DC OK
DC OK Output
Lights on when the output voltage is more than 80% of the rated value.
NPN transistor output (50V DC max., 50 mA max.)
Name
Description
+5V, +12V, +15V
DC Output Terminal
+5V side, +12V side, +15V side
-5V, -12V, -15V
DC Output Terminal
-5V side, -12V side, -15V side
COM
DC Output Terminal
0V side (wired internally to –V of PR6R-J24)
Characteristics
Operating Temperature vs.
Output Current (Derating Curves)
Overcurrent Protection Characteristics Overcurrent Protection
Characteristics PS9Z-6RM*
PS6R-24
Output Current vs. Input Voltage
(Derating Curves) (Ta=25ºC)
0
10 20 30 40 50
Operating Temperature (ºC)
60
Input Voltage(V)
264
350
120%
95%
F24
Output Voltage (%)
100
90
80
70
60
50
40
30
20
10
0
70 (ACV) 85 100
(DCV) 110 140
105%
100
Output Current (%)
100
90
80
70
60
50
40
30
20
10
0
–10
24
G24
J24
Pulse Current
(Approx. 30A rms, 40A peak)
0
0
Input Current (%)
100
Operating Temperature approved by Safety Standards
UL508, CSA C22.2 No.
107. 1
EN60950-1, EN50178
PS6R-F24
60ºC
60ºC
PS6R-G24
60ºC
60ºC
PS6R-J24
55ºC
60ºC
PS9Z-6R
55ºC
60ºC
Part No.
Barriers
Description
Input Terminal
PS9Z-6RM
Marking
Output Current (%)
Communication
Sensors
Power Supplies
Automation Software
Marking
L, N
172 www.IDEC.com
1705151126
Power Supplies
PS6R Series
PS6R-J24
PS6R-6RM1/M2/M3
Output Voltage Expansion Module
PS9Z-6RM3/M4/M6
Output Voltage Expansion Module
OI Touchscreens
Parts Description
PS6R-6RS1
Branch Terminal Module
PLCs
(PS6R-6RM5 shown)
Automation Software
PS6R-24/PS9Z-6RS1
Name
Description
L, N
Input Terminal
Voltage range: 85 to 264V AC/110 to 350V DC
Ground Terminal
Be sure to connect this terminal to a proper ground.
+V, –V
DC Output Terminals
+V: Positive output terminal
–V: Negative output terminal
VR.ADJ
Output Voltage Adjustment
Allows adjustment within ±10%. Turning clockwise increases the output voltage.
DC ON
Operation Indicator (green)
Lights on when the output voltage is on.
DC LOW
Output Low Indicator (Amber)
Lights on when the output voltage drops approximately 80% of the rated value.
DC OK
DC OK Output
Lights on when the output voltage is more than 80% of the rated value.
NPN transistor output (50V DC max., 50 mA max.)
Power Supplies
Marking
PS9Z-6RM
Marking
Name
Description
+5V, +12V, +15V
DC Output Terminal
+5V side, +12V side, +15V side
-5V, -12V, -15V
DC Output Terminal
-5V side, -12V side, -15V side
COM
DC Output Terminal
0V side (wired internally to –V of PR6R-J24)
105%
100
0
10 20 30 40 50
Operating Temperature (ºC)
60
70
Input Voltage(V)
Operating Temperature approved by Safety Standards
UL508, CSA C22.2 No. 107. 1
EN60950-1, EN50178
PS6R-F24
60ºC
60ºC
PS6R-G24
60ºC
60ºC
PS6R-J24
55ºC
60ºC
PS9Z-6R
55ºC
60ºC
24
G24
J24
Pulse Current
(Approx. 30A rms, 40A peak)
0
0
800-262-IDEC (4332) • USA & Canada
Input Current (%)
100
Barriers
1705151126
Part No.
264
350
120%
95%
F24
Output Voltage (%)
100
90
80
70
60
50
40
30
20
10
0
(ACV) 85 100
(DCV) 110 140
Overcurrent Protection Characteristics PS6R-24 Overcurrent Protection Characteristics
PS9Z-6RM*
Output Current (%)
100
90
80
70
60
50
40
30
20
10
0
–10
Output Current vs. Input Voltage
(Derating Curves) (Ta=25ºC)
Communication
Output Current (%)
Operating Temperature vs.
Output Current (Derating Curves)
Sensors
Characteristics
173
Power Supplies
PS5R-V Series
OI Touchscreens
PS5R-V Series
Switching Power Supplies
DIN-rail mount switching power supplies with global approvals for
both industrial and hazardous locations
Key Features
PLCs
• Compact size preserves panel space
• Slim size (width):
22.5mm (10W/15W/30W)
36mm (60W/90W)
45mm (7.5W)
46mm (120W)
60mm (240W)
• Universal Voltage Input:
85-264V AC/100-370V DC
• Wide operating temperature range
• Spring-up terminals accept ring & fork terminals
• Approved for use in Class I Division 2 hazardous locations
• Can be installed in 6 directions
• 7.5W ~ 90W meet NEC Class 2 output ratings
• Overcurrent protection with auto-reset
• Meets SEMI F47 Sag Immunity (208V AC input)
• RoHS compliant
• Five-year factory warranty
Power Supplies
Automation Software
Standards Compliance
Applicable Standards
UL/c-UL Listed
File No. E467154, E177168
TÜV SÜD ²
EN60950-1
EN50178
EN61204-3
EN50581
EU Low Voltage Directive,
EMC Directive
RoHS Directive
—
SEMI F47
EPRI
Note 1: PS5R-VA/VB/VC/VD/VE only
Note 2: EN60950-1, EN50178 only
Part Numbers
7.5W
Sensors
File No. or Organization
UL508
UL13101
ANSI/ISA 12.12.01
CSA C22.2 No.107.1
CSA C22.2 No.213
CSA C22.2 No.2231
Output Capacity
 10W
 15W
Part Number
Output Voltage
Output Current
PS5R-VA05
5V
1.5A
PS5R-VA12
12V
0.6A
PS5R-VA24
24V
0.3A
PS5R-VB05
 5V
 2.0A
PS5R-VB12
12V
 1.3A
24V
0.65A
PS5R-VB24
PS5R-VC12
Input Voltage
100 to 240V AC
(Voltage range: 85 to 264V AC /
100 to 370V DC)
12V
 2.5A
PS5R-VC24
24V
 1.3A
 60W
PS5R-VD24
24V
 2.5A
 30W
Communication
Mark
90W
PS5R-VE24
24V
 3.75A
120W
PS5R-VF24
24V
 5.0A
240W
PS5R-VG24
24V
10.0A
Part Number Structure
PS5R - V  
Output Capacity
Output Voltage
Barriers
A: 7.5W
05: 5V3
B: 10W/15W
12: 12V4
C: 30W
24: 24V
D: 60W
E: 90W
Note 3: PS5R-VA/VB only
F: 120W
Note 4: PS5R-VA/VB/VC only
G: 240W
Use only for interpreting part numbers.
Do not use for developing part numbers.
174 www.IDEC.com
1705151126
Power Supplies
PS5R-V Series
Specifications
100 to 240V AC
(Voltage range: 85 to 264V AC/100 to 370V DC) (Load ≤ 80% at 100-105V DC)
Frequency
Input
Input Current (Typ.)
Inrush Current (Typ.)
(Ta=25°C, cold start)
Leakage Current
Efficiency (Typ.)
(at rated output)2
50/60 Hz
100V AC
5V: 0.20A 12V, 24V: 0.18A
230V AC
5V: 0.12A 12V, 24V: 0.10A
100V AC
15A
230V AC
120V AC
230V AC
36A
100V AC
5V: 74%, 12V: 79%, 24V: 80%
41A
30A
0.96
5V/1.5A, 12V/0.6A, 24V/0.3A
5V/2.0A3, 12V/1.3A, 24V/0.65A
12V/2.5A, 24V/1.3A
24V/2.5A
24V/3.75A
24V/5A
24V/10A
12V: 13ms, 24V: 15ms
13ms
±5%
20ms
12V:  110ms 24V:  110ms
105ms
230V AC
45ms
285ms
Temperature Change
Ripple
(including noise)
Operation Indicator
Between input and ground terminals
600ms max.
±10%
30ms
30ms
800ms max.
33ms
40ms
700ms max.
800ms max.
0.05%/°C max.
(-25 to +55°C )
0.05%/°C max.
(-25 to +50°C)
200ms max.
5V, 12V:  200ms max. 24V:  250ms max.
0.4% max.
5V:  2.5% max. 12V, 24V:  1.0% max.
0.04%/°C max. (-10 to
12V:  0.05%/°C max. (-10 to +50°C)
0.05%/°C max.
0.05%/°C max. (-10 to +65°C )
+65°C )
24V:  0.05%/°C max. (-10 to +55°C)
(-10 to +55°C )
5V: 8% p-p max. (-25 to -10°C)
  5V:  8% p-p max. (-25 to -10°C)
12V:  6% p-p max. (-25 to -10°C)
12V: 6% p-p max. (-25 to -10°C)
12V:  6% p-p max. (-25 to -10°C)
24V:  4% p-p max. (-25 to -10°C)
24V: 4% p-p max. (-25 to -10°C)
24V:  4% p-p max. (-25 to -10°C)
5V: 5% p-p max. (-10 to +0°C)
  5V:  5% p-p max. (-10 to +0°C) 12V:  2.5% p-p max. (-10 to +0°C)
12V: 2.5% p-p max. (-10 to +0°C) 12V:  2.5% p-p max. (-10 to +0°C) 24V:  1.5% p-p max. (-10 to +0°C)
24V: 1.5% p-p max. (-10 to +0°C) 24V:  1.5% p-p max. (-10 to +0°C)
5V: 2.5% p-p max. (0 to +65°C)
  5V:  2.5% p-p max. (0 to +65°C)
1% p-p max. (0 to
12V:  1.5% p-p max. (0 to +50°C)
12V: 1.5% p-p max. (0 to +65°C)
12V:  1.5% p-p max. (0 to +65°C)
24V:  1% p-p max. (0 to +55°C)
+55°C)
24V: 1% p-p max. (0 to +65°C)
24V:  1% p-p max. (0 to +65°C)
105% min. (auto reset)
LED (green)
3,000V AC, 1 minute
2,000V AC, 1 minute
1.0% max.
0.05%/°C max.
(-10 to +50°C )
4% p-p max. (-25 to -10°C)
1.5% p-p max. (-10 to +0°C)
1% p-p max. (0 to
+50°C)
101% min. (auto reset)
1% p-p max. (0 to +55°C)
1% p-p max. (0 to
+50°C)
105% min. (auto reset)
Power Supplies
Between input and output terminals
±10%
5V: 53ms, 12V: 34ms, 24V: 36ms
 5V: 330ms 12V: 215ms
24V: 230ms
500ms max.
89%
90%
88%
89%
Automation Software
Input Fluctuation
Load Fluctuation
Output
14A
45A
0.99
0.92
5V, 12V: 200ms max
24V: 250ms max
Regulation
1.2A
18A
0.86
Overcurrent Protection
Dielectric
Strength
2.7A
0.7A
86%
86%
—
—
Rise Time (at rated input and output)
500V AC, 1 minute
Between output and ground terminals
Between input and output terminals:  100MΩ min. (500V DC megger) Between input and ground terminals:  100MΩ min. (500V DC megger)
-25 to +75°C
-25 to +70°C
-25 to +65°C
20 to 90% RH (no condensation)
-25 to +75°C
20 to 90% RH (no condensation)
Insulation Resistance
Operating Temperature4 (No freezing)
Operating Humidity
Storage Temperature (No freezing)
Storage Humidity
10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes
(when used with BNL6 end clips)
Vibration Resistance
Expected Life5
EMI
EMS
Safety Standards
Other Standard
Degree of Protection
75H × 45W × 70D
130g
10 to 55Hz, amplitude 0.33mm, 2 hours each in 3 axes
(when used with BNL6 end clips)
10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes
(when used with BNL8 end clips)
10 to 55Hz, amplitude 0.21mm, 2
hours each in 3 axes
(when used with BNL6 end clips)
10 to 55Hz, amplitude 0.375mm, 2
hours each in 3 axes (when used with
BNL8 end clips)
10 to 55 Hz, amplitude
0.375mm, 2 hours each
in 3 axes
(when used with part no.
BNL6 mounting clips)
300 m/s2 (30G), 3 times each in 6 directions
8 years minimum (at the rated input, 50% load, operating temperature +40°C, standard mounting direction)
EN61204-3 (Class B)
EN61204-3 (industrial)
UL508 (Listing), UL1310 Class 2, ANSI/ISA-12.12.01
UL508 (Listing) ANSI/ISA-12.12.01
CSA C22.2 No. 107.1, 213, 223 EN60950-1, EN50178
CSA C22.2 No. 107.1, 213
EN60950-1, EN50178
SEMI F47 (at 208V AC input only)
IP20 (EN60529)
90H × 22.5W × 95D
95H × 36W × 108D
115H × 46W × 121D
125H × 60W × 125D
140g
150g
260g
310g
470g
960g
M3.5
Sensors
Shock Resistance
Communication
Terminal Screw
1.4A
0.6A
12V: 83%, 24V: 85%
12V: 85%, 24V: 87%
—
—
500ms max.
Weight (approx.)
1.1A
0.8A
0.5mA max.
1.0mA max.
Start Time (at rated input and output)
Dimensions (mm)
1.3A
0.3A
5V: 77%, 12V: 82%, 24V: 84%
5V:   73%, 12V:  80%, 24V:  81%
—
—
Adjustable Voltage Range
Output Holding Time 100V AC
EMC
0.7A
230V AC 5V: 73%, 12V: 77%, 24V: 76%
—
100V AC
—
230V AC
Rated Voltage/Current
(Typ.) (at rated output)
 5V:     0.25A
12V, 24V:  0.35A
 5V:     0.14A
12V, 24V:  0.19A
PLCs
Power Factor (Typ.)
OI Touchscreens
Rated Input Voltage
(Single-phase two-wire)1
*At normal temperature and humidity unless otherwise specified.
Note 1: DC input voltage is not subject to safety standards. When using on DC input, connect a fuse to the input terminal for DC input protection.
Note 2: Under stable state.
Note 3: PS5R-VB05 (5V DC/2.0A) is 10W (Up to 3.0A at Ta = 0 to 40°C. Not subject to safety standards above 2.0A.)
Note 4: See the output derating curves.
Note 5: Calculation of the expected life is based on the actual life of the aluminum electrolytic capacitor. The expected life depends on operating conditions.
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
175
Power Supplies
Characteristics
Operating Temperature vs. Output Current (Derating Curves)
Conditions: Natural air cooling (Operating temperature is the temperature around the switching power supply.)
PS5R-VA05, -VA12, -VA24
PS5R-VB05, -VB12, -VB24
Mounting A,E
90
90
Output Current (%)
80
70
60
50
40
Mounting B, C, D, F
30
20
10
0
-30 -20 -10
0
10
20
30
40
50
60
Operating Temperature (˚C)
10
0
-30 -20 -10
50
30
Mounting D, E, F
20
10
0
-30 -20 -10
0
10
20
30
40
50
60
70
Operating Temperature (˚C)
30
40
50
60
70
80
40
30
20
Mounting B, C, D, E, F
10
0
-30 -20 -10
0
10
20
30
40
50
60
70
100
80
40
Mounting A
Mounting F
10
0
-30 -20 -10
0
10
20
30
40
50
60
70
Mounting A
90
50
20
50
Operating Temperature (˚C)
Mounting B, C, D
60
30
60
PS5R-VE24
Input Voltage:
85-100V AC
70
Input Voltage:
85-100V AC
70
80
Mounting E
70
60
50
40
Mounting
B, C, D, F
30
20
10
0
-30 -20 -10
80
Operating Temperature (˚C)
0
10
20
30
40
50
60
Operating Temperature (˚C)
70
80
PS5R-VG24
100
Mounting A
100
Mounting C, E
90
90
80
Mounting E
80
70
Mounting B, D
60
50
40
Mounting A
Mounting F
10
0
-30 -20 -10
0
10
20
30
40
50
60
70
Operating Temperature (˚C)
80
70
50
40
20
10
0
-30 -20 -10
0
10
20
30
40
50
60
90
80
80
Output Current (%)
100
70
60
50
40
30
20
10
70
80
AC
DC
60
50
40
30
20
10
0
(ACV) 85 100
(DCV)100 105
264
370
70
PS5R-VA05, -VA12, -VA24, -VG24
90
Input Voltage (V)
Mounting
C, D, F
30
100
0
(ACV) 85 100
(DCV) 100 140
Mounting B
60
Operating Temperature (˚C)
Input Voltage vs. Output Current (Derating Curves) Ta=25°C
PS5R-VB05, -VB12, -VB24, -VC12, -VC24, -VD24,
-VE24, -VF24
Output Current (%)
20
Mounting E
80
80
PS5R-VF24
20
10
90
Mounting C
40
30
0
100
Output Current (%)
Output Current (%)
60
Output Current (%)
Automation Software
20
Operating Temperature (˚C)
Input Voltage:
85-100V AC
70
Mounting B, C, D, E, F
PS5R-VD24
90
Sensors
40
Mounting A, B
80
80
50
30
Mounting A
90
60
80
PS5R-VC24
100
Power Supplies
70
100
Input Voltage:
85-100V AC
70
Output Current (%)
PLCs
Output Current (%)
80
PS5R-VC12
Mounting A
100
Output Current (%)
100
Output Current (%)
OI Touchscreens
PS5R-V Series
Input voltage (V)
264
370
PS5R-VA/VB/VC/VD/VF
100
PS5R-VG24
100
95
Output Current (%)
176 100
105 and over
Output Voltage (%)
Output Voltage (%)
Intermittent Operation
100
95
0
-30 0
Barriers
PS5R-VE24
Output Voltage (%)
Communication
Overcurrent Protection Characteristics
Intermittent Operation
0
Intermittent Operation
0
0
Output Current (%)
100
101 and over
www.IDEC.com
0
Output Current (%)
100
105 and over
1705151126
Power Supplies
PS5R-V Series
Operating Temperature Approved by Safety Standards
OI Touchscreens
UL508, CSA C22.2 No.107.1, ANSI/ISA12.12.01, EN60950-1, EN50178
Part Number
Mounting B
Mounting C
Mounting D
Mounting E
Mounting F
PS5R-A05, -VB12, -VB24
65
60
60
60
65
60
PS5R-VB05, -VB12, -VB24
65
60
60
60
60
60
PS5R-VC12
50
45
45
45
45
45
PS5R-VC24
55
55
50
45
45
45
PS5R-VD24
55
40
40
40
45
35
PS5R-VE24
50
40
40
40
45
40
PS5R-VF24
55
40
45
40
45
35
PS5R-VG24
50
35
30
30
45
30
PLCs
Mounting A
Mounting Style
Mounting B
(Upright)
Mounting A
(Vertical, standard)
Mounting C
(Right side up)
Mounting E
(Upside down)
Mounting D
(Left side up)
Automation Software
Up
Mounting F
(Downward)
Front Panel
PS5R-VA
PS5R-VB/VC PS5R-VD/
VE/VF
L
N
Marking
Name
Description
L, N
AC Input Terminal
Voltage range: 85 to 264V AC/100 to 370V DC
Ground Terminal
Be sure to connect this terminal to a proper
ground.
INPUT 50/60Hz
+V, -V
DC Output Terminals
+V: Positive output terminal
-V: Negative output terminal
DC ON
VR.ADJ
Output Voltage Adjustment
Allows adjustment within ±10%. (VE = ±5%)
Turning clockwise increases the output voltage.
Turning counterclockwise decreases the output
voltage.
DC ON
Operation Indicator (green)
Illuminates when the output voltage is on.
100 -240 VAC
ON
VR.
ADJ
VR .
ADJ
Power Supplies
INP U T
PS5R-VG
OUTPUT
Sensors
-V
+V
O U TP U T
Accessories
Panel Mounting Bracket2
Applicable Switching Power Supply
PS5R-VG
Remarks
—
For side mounting
PS9Z-5R1C
—
PS9Z-5R1E
—
PS9Z-6R1F
—
PS9Z-6R2F
For side mounting
Communication
PS5R-VB
PS5R-VC
PS5R-VD
PS5R-VE
PS5R-VF
Part Number
PS9Z-5R1B
PS9Z-5R2B
Note 2: Used when installing on a panel directly, PS5R-VA model does not require panel mounting bracket.
DIN Rail (35mm-wide)
1000mm
BNDN1000
Aluminum
End Clip
Barriers
Part Number
BNL6
BNL8
1705151126
800-262-IDEC (4332) • USA & Canada
177
Power Supplies
Dimensions (mm)
PS5R-VA
PS5R-VA
PS5R-VB/VC
5-M3.5
Screw Terminal
27.3
61.6
4.4
5
7.35
3.8
9.5
22.5
PS5R-VD/VE
3.8
PS5R-VF
108
8.5
5-M3.5
Screw Terminal
11.5 11.5
5-M3.5
Screw Terminal
121
35.3
115
4.5
98
95
35.3
44.9
24.9
8
10 10
79
Automation Software
90
19.9
35.3
75
PLCs
26
35
38.5
45
20
36
3.8
4.5
Power Supplies
95
12.2 8.2
6
35.3
70
6-M3.5
Screw Terminal
62.5
60
OI Touchscreens
PS5R-V Series
23
46
PS5R-VG
8-M3.5
Screw Terminal 9.5 9.5
MTBF*
5.5
1 25
9 .3
PS5R-VA:
1,150,000H minimum
PS5R-VB: 900,000H minimum
44 .9
Sensors
PS5R-VC: 650,000H minimum
35 .3
12 5
PS5R-VD: 450,000H minimum
10 6 .5
3.8
PS5R-VE: 380,000H minimum
MIL-HDBK-217FN2
(GB, 30°C)
PS5R-VF: 350,000H minimum
60
3 .8
4 .5
9.5 9.5 9.5 9.5
*MTBF stands for Mean Time Between Failure, which is calculated according to
statistical device failures, and indicates reliability of a device. It is the statistical
representation of the likelihood of the unit to fail and does not necessarily represent the expected life of a product.
Barriers
Communication
PS5R-VG: 290,000H minimum
* 3-Phase
178 www.IDEC.com
1705151126
Power Supplies
When installed on switching power supply
OI Touchscreens
PS9Z-5R1B
13.6
Panel Mounting Bracket
PS5R-V Series
12
24.7
12
PS9Z-5R2B Side-mount
16.4
Mounting hole layout
when installing on
a panel directly
Front View
96.7
Side View
10.0
120
112
112
2-M4 or 2- ø 4.5 holes
2-M4 or 2- ø 4.5 holes
28.8
5.5
102
10.0
110
102.0
PLCs
Mounting hole layout
when installing on
a panel directly
44
62.9
Side View
10.2
109.8
105
115
105
2-M4 or 2- ø 4.5 holes
Automation Software
PS9Z-5R1C
Front View
26
26
38
PS9Z-5R1E
9.9
Mounting hole layout
when installing on
a panel directly
Front View
Side View
125
10.2
122.8
Power Supplies
135
125
2-M4 or 2- ø 4.5 holes
10.5
4-M4 or 4- ø 4.5 holes
130.6
10.5
145
135
145
135
Sensors
28
Side View
10
PS9Z-6R1F
Front View
9.9
36
36
48
Mounting hole layout
when installing on
a panel directly
Mounting hole layout
when installing on
a panel directly
28
PS9Z-6R2F Side-mount
Side View
Front View
4-M4 or 4- ø 4.5 holes
29.5
62.3
31
138.6
148.6
138.6
11.8
56
Communication
28
39
56
11.8
56
70
Side View
1705151126
Barriers
Mounting hole
layout for side
mounting
800-262-IDEC (4332) • USA & Canada
Back View
Mounting Screws
(4 -M3×6 countersunk screws)
179
Power Supplies
Power Supplies
Automation Software
PLCs
OI Touchscreens
PS5R-V Series
Mounting on DIN Rails
Safety Precautions
The PS5R-V should be placed in a proper enclosure. It is designed to be used with
general electrical equipment and industrial electric devices
• Do not use switching power supplies with electric equipment whose malfunction or
inadvertent operation may damage the human body or life directly.
• Make sure that the input voltage and output current do not exceed the ratings.
If the input voltage and output current exceed the ratings, electric shock, fire, or
malfunction may occur.
• Do not touch the terminals of the switching power supply while input voltage is
applied, otherwise electric shock may occur.
• Provide the final product with protection against malfunction or damage that may be
caused by malfunction of the switching power supply.
• Operating temperatures should not exceed the ratings. Be sure to note the derating
characteristics. If the operating temperature exceeds the ratings, electric shock, fire,
or malfunction may occur.
• Blown fuses indicate that the internal circuits are damaged. Contact IDEC for
repair. Do not just replace the fuse and reoperate, otherwise electric shock, fire, or
malfunction may occur.
• Do not use the switching power supplies to charge rechargeable batteries.
• Do not overload or short-circuit the switching power supply for a long period of time,
otherwise the internal elements may be damaged.
• Do not disassemble, repair, or modify the power supplies, otherwise the high voltage
internal part may cause electric shock, fire, or malfunction.
• The fuse inside the PS5R-V switching power supply is for AC input. Use an external
fuse for DC input.
1. Use a 35mm-wide DIN rail.
2.Place the PS5R-V on the DIN rail as shown with input terminal side up (➀),
and press the PS5R-V towards the DIN rail (➁). Make sure that the PS5R-V is
installed firmly.
3. Use BNL6 end clips to ensure power supplies do not slide off the end of the
DIN rail. Use of BNL8 end clips is recommended when excessive vibration or
shock is anticipated.
Removal
• Insert a flat screwdriver into the slot in the clamp, and pull out until it clicks (➀). The
lock mechanism is released and the PS5R-V can be removed (➁). When mounting the
PS5R-V again, push in the latch first.
Mounting
Removal
Clamp
Installing a Panel Mounting Bracket
Panel Mounting Bracket (PS9Z-5R1, PS9Z-6R1F)
Tab

Power
Supply

Notes for installation
 Install the tab on the panel
mounting bracket into the slot
on the power supply.

 Install the brackets as shown
on the left.
 Ensure that the panel mounting
bracket is locked by the latch.
Sensors
LOCK
10mm minimum
• When the derating voltage may exceed the recommended value, provide forced
air-cooling.
• Make sure to wire the ground terminal correctly.
• For wiring, use wires of heat resistance of 60oC or higher (PS5R-VB: 80oC or higher).
Use copper wire of the following sizes, according to the rated current.
Communication
UNLOCK
Latch

Terminal
Wire Size (allowable current)
Input
AWG 18 to 14
Output
AWG18 to 14 (AWG18: 7A, AWG16: 10A,
AWG14: 15A)
Panel Mounting Bracket (PS9Z-5R2B)

UNLOCK

Copper Solid/Stranded
Power
Supply
Latch
Cross-Sectional are AWG18: 0.82mm2, AWG16: 1.31mm2, AWG14: 2.0mm2
 Push in the latch to LOCK
position.
5.5 min.

• Recommended tightening torque of the input and output terminals is 1.0 to
1.3Nm (0.8N·m for UL).
180  Insert the tab on the panel
mounting bracket into the slot
on the power supply.

ø3.6min.
6.6 max.
4 max.
 Pull out the latch to
UNLOCK position.
LOCK
Tab
Wire Type
Applicable crimp terminal (reference)
Barriers
 Push in the latch to LOCK
position.
LOCK
Operating Instructions
• Do not close the top or bottom openings of the PS5R-V to allow for heat radiation by
convection.
• When mounting multiple PS5R-V switching power supplies side by side, maintain a
minimum of 10 mm clearance. Observe the derating curves in consideration of the
ambient temperature.
Slot
www.IDEC.com
 Ensure that the panel mounting
bracket is locked by the latch.
LOCK
1705151126
Power Supplies
Installing PS9Z-6R2F Side-mount Panel Mounting Bracket
Rust and Scratches on Metal parts
Bonded metal parts are used for the PS5R-V. Rust on the edge and scratches on the
surfaces may be developed depending on the storage condition, but the performance of
the PS5R-V is not affected.
OI Touchscreens
Install the bracket on the switching power supply using four M3 × 6 countersunk screws
supplied with the bracket. Recommended tightening torque is 0.5 to 0.6N.m (should be
in the center positions)
PS5R-V Series
Panel Mounting Bracket (PS9Z-5R1, PS9Z-6R1F)
Tab

Slot
 Push in the latch to LOCK
position.
Noise
LOCK
Power
Supply

Small acoustic noise inside the PS5R-V may be heard depending on the input voltage
and load, but the performance of the PS5R-V is not affected.
UNLOCK
Latch
 Install the tab on the panel
mounting bracket into the slot
on the power supply.

Series Operation
 Install the brackets as shown
on the left.

Series operation is allowed. Connect Schottky barrier diodes D as shown below. Select
a Schottky diode in consideration of the rated current. The diode’s reverse voltage must
be higher than the PS5R-V’s output voltage.
 Ensure that the panel mounting
bracket is locked by the latch.
LOCK
Tab
 Pull out the latch to
UNLOCK position.

LOCK
L
L
+V
UNLOCK
N
N
–V
Load
L
N
+V
–V
Load
L
L
+V
N
N
–V
L
N
+V
–V

Power
Supply
Latch
Load
 Insert the tab on the panel
mounting bracket into the slot
on the power supply.

Adjustment of Output Voltage
 Push in the latch to LOCK
position.
The output voltage can be adjusted within ±10% (VE: ±5%) of the rated output voltage
by using the VR.ADJ control on the front. Turning the VR.ADJ clockwise increases the
output voltage. Turning the VR.ADJ counterclockwise decreases the output voltage.

PLCs
Panel Mounting Bracket (PS9Z-5R2B)
(b)
(a)
 Ensure that the panel mounting
bracket is locked by the latch.
LOCK
The output voltage drops automatically when an overcurrent flows due to an overload or
short circuit. Normal voltage is auto­matically restored when the load returns to normal
conditions.
Insulation/Dielectric Test
When performing an insulation/dielectric test, short-circuit the input (between L and N)
and output (between +V and -V). Do not apply or interrupt the voltage quickly, otherwise
surge voltages may be generated and the PS5R-V may be damaged.
• Output interruption may indicate blown fuses. Contact IDEC.
• The PS5R-V switching power supply contains an internal fuse for AC input. When
using DC input, install an exter­nal fuse. To avoid blown fuses, select a fuse in
consideration of the rated current of the internal fuse.
Parallel Operation
Parallel operation is not possible to increase the output capacity,
because the internal elements and load may be damaged.
Backup Operation
Backup operation is a connection method of two switching power supplies in parallel
for emergency. Normally one switching power supply has a sufficient output. If one
switching power supply fails, another one operates to continue the output. Make sure
that the sum of power
consumption by load and diode is not greater than the rated wattage (rated voltage ×
rated
current) of one switching power supply.
D
AC
Rated Current of Internal Fuses
Part Number
IN
Load
OUT
−
D
IN
Internal FuseRated Current
2A
PS5R-VD/VE/VF
4A
OUT
−
Select a diode in consideration of:
Diode’s current must be more than double the PS5R-V’s output current. Take heat dissipation into consideration.
Sensors
PS5R-VB/VC
PS5R-VG
Power Supplies
Notes for Operation
Automation Software
Overcurrent Protection
6.3A
• Avoid overload and short-circuit for a long period of time, oth­erwise the internal
elements may be damaged.
• DC input operation is not subject to safety standards.
Warranty
Scope
1705151126
800-262-IDEC (4332) • USA & Canada
Barriers
IDEC agrees to repair or replace the PS5R-V switching power supply if the product has
been
operated under the following conditions. The maximum value of output capacity is
within the range shown in “Operating Temperature vs.
Output Current on page 3.
1. Average operating temperature (ambient temperature of switching power supply)
is 40°C maximum.
2. The load is 80% maximum.
3. Input voltage is the rated input voltage.
4. Standard mounting style
IDEC shall not be liable for other damages including consequential, contingent or
incidental
damages. Warranty does not apply if the PS5R-V switching power supply was subject
to:
1. Inappropriate handling, or operation beyond specifications.
2. Modification or repair by other than IDEC.
3. Failure caused by other than the PS5R-V switching power supply.
4. Failure caused by natural disasters.
Communication
IDEC warranties the PS5R-V switching power supply for a period of five years from the
date of shipment.
181
Power Supplies
Automation Software
PLCs
OI Touchscreens
PS5R Slim Line Series
PS5R Slim Line Series
Switching Power Supplies
Key features:
• Lightweight and compact in size
• Wide power range: 10W-240W
• Universal input:
10W to 90W: 85-264V AC/100-370V DC
120W and 240W: 85-264V AC/100-350V DC
• Power Factor Correction for 60W to 240W
(EN61000-3-2)
• Meets SEMI F47 Sag Immunity (120W & 240W only)
• UL Listed for Class 1, Div. 2 Hazardous Locations
• Overcurrent protection, auto-reset
• Overvoltage protection, shut down
• Spring-up screw terminal type, IP20
• DIN rail or panel surface mount
• Approvals:
CE Marked
ANSI/ISA-12.12.01-2011 (Hazardous locations)
TÜVEN50178:1997
c-UL, UL508
LVD: EN60950:2000
UL1310 (PS5R-SB, -SC, -SD)
EMC: Directive EN61204-3:2000 (EMI: Class B, EMS: Industrial)
Universal Input Power
Power Supplies
The applied input power has a range of 85-264V
AC (100-350V DC) without the use of jumpers or
slide switches. This makes IDEC power supplies
suitable for use anywhere in the world.
The indicator turns on when the output
voltage drops below 80% of the rated value.
This assists in troubleshooting power supply
problems.
Long Life Expectancy
DC ON Indicator
The indicator turns on when the unit is powered
up. This is a convenient way to know when the
power supply is receiving power.
IDEC power supplies are very reliable, with a life
expectancy of 70,000 hrs. (minimum) or longer,
depending on usage. Power factor correction
has also been included to minimize harmonic
distortion, resulting in a longer operating life and
increased reliability.
Output Voltage Adjustment
Output Channel
The output voltage can be easily adjusted within
+ 10% of the rated voltage.
With very low output ripples of less than 1% peak
to peak, the 120W and 240W power supplies are
some of the best in the industry. The output comes
with overload protection that avoids damaging the
power supply and the spring-up, fingersafe, screw
terminals add a level of safety and ease for the
user. The 240W power supply also has the convenience of two output terminals.
Communication
Sensors
(SEMI F47 120W &
240W only)
Designed with Accessibility & Convenience in Mind
DC Low Indicator
(15W, 120W & 240W Slim Line Only)
Fingersafe, Spring-up Screw Terminals
Barriers
File #E234997
Top
View
Provides cooling for
the power supply and
prevents small objects
from falling into the
power supply circuitry.
Terminals are captive spring-up screws, which makes using them
as easy as pushing a screw down and tightening it.
They are shock and vibration resistant, and work with ring lugs,
fork connectors or stripped wire connections. The terminals are
rated IP20 (when tightened) meaning they are recessed to keep
fingers and objects from touching the input contacts.
182 Ventilation Grill
www.IDEC.com
1705151126
Power Supplies
PS5R Slim Line Series
Output
Capacity
Style
10
5V DC
2.0A
PS5R-SB05
12V DC
1.2A
PS5R-SB12
24V DC
0.65A
PS5R-SB24
12V DC
2.5A
PS5R-SC12
24V DC
1.3A
PS5R-SC24
24V DC
2.5A
PS5R-SD24
Input
Voltage
90
OI Touchscreens
Part Numbers
Output
Voltage
Rated
Current
Part
Number
24V DC
3.75A
PS5R-SE24
24V DC
5A
PS5R-SF24
24V DC
10A
PS5R-SG24
15
120
Panel Mounting Bracket for PS5R-SB (flat side mounting)
PS9Z-5R2B
Panel Mounting Bracket for PS5R-SC and PS5R-SD
PS9Z-5R1C
Panel Mounting Bracket for PS5R-SE
PS9Z-5R1E
Panel Mounting Bracket for PS5R-SF & PS5R-SG
PS9Z-5R1G
DIN rail (1000mm)
BNDN1000
DIN rail end clip
BNL5
800-262-IDEC (4332) • USA & Canada
Barriers
PS9Z-5R1B
Communication
1705151126
Panel Mounting Bracket for PS5R-SB
Sensors
Accessories
Power Supplies
240
85 to 264V
AC
Automation Software
60
PLCs
30
85 to 264V
AC
183
Power Supplies
OI Touchscreens
PS5R Slim Line Series
Specifications
Model
5V DC output
PS5R-SB05
–
–
–
–
–
12V DC output
PS5R-SB12
PS5R-SC12
–
–
–
–
24V DC output
PS5R-SB24
PS5R-SC24
PS5R-SD24
PS5R-SE24
PS5R-SF24
PS5R-SG24
15W (5V Model is 10W)
30W
60W
90W
120W
240W
Output Capacity
Input Voltage
(single-phase, 2-wire)
100VAC
0.45A
0.9A
200VAC
0.3A
0.6A
Internal Fuse Rating
Input
PLCs
Input Current
(maximum)
2A
Typical
Efficiency
Output Current
Ratings
2.3A
1.0A
1.4A
1.7A
6.3A
0.75mA maximum
1mA maximum
69%
–
–
–
–
–
75%
78%
–
–
–
–
24V DC
79%
80%
83%
82%
5V DC
2.0A
–
–
–
–
12V DC
1.2A
2.5A
–
–
–
–
24V DC
0.65A
1.3A
2.5A
3.75A
5A
10A
650ms maximum
500ms maximum
–
–
–
100ms maximum (at rated input and output)
Line Regulation
200ms maximum
0.4% maximum
Load Regulation
1.5% maximum
Temperature Regulation
0.8% max
0.05% degree C maximum
Ripple Voltage
2% peak to peak maximum (including noise)
105% or more, auto reset
1% peak to peak maximum (including noise)
105 to 130%, auto reset
LED (green)
LED (amber)
–
–
–
LED (amber)
Between Input and Ground: 2000 V AC, 1 minute
Between input and output: 3000V AC, 1 minute;
Between output and ground: 500V AC, 1 minute.
Dielectric Strength
Insulation Resistance
Between Input & Output Terminals: 100 MΩ Min
–10 to +65°C (14 to 149°F)
-10 to 60°C (14 to 140°F)
Storage Temperature
-25 to 75°C (-13 to +167°F)
Operating Humidity
20 to 90% relative humidity (no condensation)
Vibration Resistance
Frequency 10 to 55Hz, Amplitude 0.375mm
Shock Resistance
Approvals
300m/s2 (30G) 3 times each in 6 axes
EMC: EN61204-3 (EMI: Class B, EMS: Industrial), c-UL (CSA 22.2 No. 14), ANSI/ISA-12.12.01-2011, UL508, LVD: EN60950, EN50178
UL1310 Class 2, c-UL (CSA 22.2 No. 213 and 223)
Harmonic Directive
Weight (approx.)
160g
SEMI F47
EN61000-3-2 A14 class A
250g
285g
440g
630g
1000g
M3.5 slotted-Phillips head screw (screw terminal type)
IP protection
Dimensions H x W x D (inches)
–
N/A
Terminal Screw
Dimensions H x W x D (mm)
103 to 110%, auto reset
120% min. SHUTDOWN
Operation Indicator
Operating Temperature
–
20ms minimum (at rated input and output)
200ms maximum
Rise Time
Voltage Low Indication
84%
±10% (V. ADJ control on front)
Overvoltage Protection
Sensors
1.0A
4A
12V DC
Overcurrent Protection
Communication
3.5A
5V DC
Starting Time
Barriers
1.8A
50A maximum (at 200V AC)
132V AC: 0.38 mA maximum
264V AC: 0.75 mA maximum
Voltage Adjustment
Output
1.7A
3.15A
Output Holding Time
Power Supplies
85 to 264V AC,
100 to 350V DC
Inrush Current (cold start)
Leakage Current (at no load)
Automation Software
85 to 264V AC,
100 to 370V DC
IP20 fingersafe
90 x 22.5 x 95
95 x 36 x 108
115 x 46 x 121
115 x 50 x 129
125 x 80 x 149.5
3.54 x 0.89 x 3.74
3.74 x 1.42 x 4.25
4.53 x 1.81 x 4.76
4.53 x 1.97 x 5.08
4.92 x 3.15 x 5.89
1. For dimensions, see page 186.
184 www.IDEC.com
1705151126
Power Supplies
PS5R Slim Line Series
All IDEC Slim Line power supplies are listed to UL508, which allows operation
at 100% capacity inside a panel. This eliminates the need to use oversize power
supplies or utilize two power supplies derated at 50% of their rated output.
Mounting B
(upright)
PS5R-SC
Mounting B, C, D
0
10
20
30
40
Mounting C
(left side up)
50 55 60 65 70
Mounting D
(right side up)
Operating Temperature (°C)
Dearting curve for PS5R-SB varies depending on
mounting method (see right).
0
10 20 30 40
50 55 60
Operating Temperature (ºC)
70
0
10 20 30 40 45 50
Operating Temperature (ºC)
60
70
PS5R-SE 90W/3.75A/24V DC versus a Leading Competitor
Standard derating curve (operating temperature vs. output current)
Don’t Believe the Hype
Output Cuurent (%)
4.0
Currrent (A)
“Boost” Rating 3.75A
0
10 20 30 40
50
Operating Temperature (ºC)
60
Other companies use slick marketing to sell you 60W power
supplies with a “BOOST,” but what they don’t tell you is that
these are merely 90W power supplies that have been renamed
to fool you into thinking they have a unique feature. IDEC 90W
power supplies are just what they claim, 90W power supplies.
The truth is IDEC led the market by incorporating UL508 DIN rail
mount power supplies as a standard product. Don’t let the other
guys pull a fast one on you by claiming to provide features that
just aren’t true, or even possible. See what IDEC has to offer, no
strings attached.
3.0
“Normal” Rating 2.5A
2.0
70
1.0
Leading Competitor
“24V/2.5A”
Power Supplies
100
90
80
70
60
50
40
30
20
10
0
-10
100
90
80
70
60
50
40
30
20
10
0
-10
Automation Software
PS5R-SD, -SE, -SF
100
90
80
70
60
50
40
30
20
10
0
-10
PS5R-SG
Output Cuurent (%)
Mounting A
(standard)
Output Cuurent (%)
100
90
80
70
60
50
40
30
20
10
0
–10
Mounting A
PLCs
Output Current (%)
PS5R-SB
The charts below show that the PS5R Slim 10W (at 60ºC) and 15W (at 60ºC),
30W/60W/90W (at 55ºC), 120W (at 40ºC), and 240W (at 45ºC) meet the
elevated, operating temperature required by UL508 and EN60950 standards to
operate at an output current of 100%. The output current starts to derate beyond
the required temperature.
OI Touchscreens
Temperature Derating Curves
Overload Protection
Overload protection prevents the power supply from being damaged when an overload occurs. There are two kinds of protection.
When the output voltage of the
power supply rises to 120% or more
of the rated value, the output will
shut off. To restore power, only
manual reset is available which is an
advantage in troubleshooting.
Overvoltage Protection
Communication
Overcurrent Protection
PS5R-SF, -SG
Overvoltage Protection
When the output current exceeds
105% of the rated current, overload
protection is triggered, and the
output voltage starts decreasing.
When the output current returns
within the rated range, the overload
protection function is automatically
cleared.
Sensors
24
Overcurrent Protection
SEMI-F47 Approved
The SEMI F47 (Semiconductor Processing Equipment Voltage Sag Immunity) defines the minimum voltage sag
ride-through requirements for semiconductor processing, automated test equipment and other equipment. It
requires that the equipment be able to tolerate voltage sags on an AC power line without interrupting operations. This avoids the loss of production and money.
The graph shows how the equipment must tolerate sags to 50% for 200ms, sags to 70% for up to 0.5 seconds
and sags to 80% for up to 1 second.
Barriers
Voltage Sag Sliding Scale PS5R-SF, -SG
1705151126
800-262-IDEC (4332) • USA & Canada
185
Power Supplies
OI Touchscreens
PS5R Slim Line Series
Dimensions and Terminal Markings
PS5R-SB
PS5R-SC
PS5R-SD
Height90mm
Width22.5mm
Depth95mm
PS5R-SE
Height95.0mm
Width36.0mm
Depth108.0mm
INPUT
100-240VAC
LOW
L
N
Height115.0mm
Width46.0mm
Depth121.0mm
INPUT 50/60Hz
DC ON
VR.
ADJ
ON
L
N
INPUT 50/60Hz
DC ON
VR.
ADJ
VR.
ADJ
OUTPUT
PLCs
-V
OUTPUT
+V
-V
+V
PS5R-SF
PS5R-SG
Height115.0mm
Width50.0mm
Depth129.0mm
Height
Width
Depth
125.0 mm
80.0 mm
149.5 mm
Sensors
149.5
125
Power Supplies
Automation Software
OUTPUT
Front Panel (terminals)
Markings
Name
Description
V. ADJ
Voltage adjustment
Adjusts within ±10%; turn clockwise to
increase output voltage.
DC ON
Operation indicator
Green LED is lit when output voltage is on.
DC Low
Output indicator
Amber LED is lit when output voltage drops
below 80% of rated voltage.
+V, –V
DC output terminals
+V: Positive output Terminal
–V: Negative output terminal
Frame ground
Ground this terminal to reduce high-frequency
noise caused by switching power supply.
Input terminals
Accept a wide range of voltages and
frequencies (no polarity at DC input).
Barriers
Communication
80
L, N
186 www.IDEC.com
1705151126
Power Supplies
PS5R Slim Line Series
PS9Z-5R1B (for PS5R-SB)
PS9Z-5R2B (for PS5R-SB)
PS9Z-5R1B
OI Touchscreens
Mounting Bracket Dimensions (mm)
PS9Z-5R1C (for PS5R-SC & PS5R-SD)
120
112
44
115
105
62.9
PS9Z-5R2B
102
110
PLCs
2-M4 tapped holes or 2-ø4.5 through holes
(See the front page for mounting examples.)
26
38
12
24.7
2-M4 Tapped Holes or
2-ø4.5 Drilled Holes
2-M4 tapped holes or 2-ø4.5 through holes
PS9Z-5R1G (for PS5R-SF & PS5R-SG)
Automation Software
135
145
135
125
PS9Z-5R1E (for PS5R-SE)
Power Supplies
36
48
2-M4 Tapped Holes or
2-ø4.5 Drilled Holes
36
48
4-M4 Tapped Holes or
4-ø4.5 Drilled Holes
Sensors
Communication
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
187
Power Supplies
Automation Software
PLCs
OI Touchscreens
PS5R Standard Series
PS5R Standard Series
Switching Power Supplies
Key features:
• Wide power range: 7.5W-480W
• Universal input :
7.5W-50W: 85-264V AC/105-370V DC
100W: 85-132V AC/170-264V AC
240-370V DC (selectable)
75W, 120W, 240W: 85-264V AC/110-350V DC
480W: 3 phase: 320- 575V AC
3 phase: 360- 575V AC
• Overcurrent/overvoltage protection
• Power Factor Correction (75W, 120W, 240W models)
EN61000-3-3
EN61000-3-2
• Voltage adjustment +10%
• Spring-up crew terminal, IP20 (finger-safe)
• DIN rail or panel surface mount
• Approvals:
CE marked
EMC Directives: UL 508
Listed
EN50081-2
c-UL EN50082-2
TÜV approved
EN61000-6-2
LVD EN60950:2000
UL 508 Listed
File #E177168
Cert No.
BL980213332392
Power Supplies
Part Numbers
7.5
Sensors
15
85 to 264V
AC
5V DC
1.5A
PS5R-A05
12V DC
0.6A
PS5R-A12
24V DC
0.3A
PS5R-A24
5V DC
2.5A
PS5R-B05
12V DC
1.2A
PS5R-B12
24V DC
0.6A
PS5R-B24
12V DC
2.5A
PS5R-C12
24V DC
1.3A
PS5R-C24
24V DC
2.1A
PS5R-D24
Style
Communication
75
Input
Voltage
85 to 264V
AC
100
30
50
Output
Capacity
120
100 to 240V
AC
240
Barriers
480
188 www.IDEC.com
320 to
575V AC (3
phase)
360 to
575V AC (2
phase)
Output
Voltage
Rated
Current
Part
Number
24V DC
3.1A
PS5R-Q24
24V DC
4.2A
PS5R-E24
24V DC
5A
PS5R-F24
24V DC
10A
PS5R-G24
24V DC
20A
PS5R-TJ24*
1705151126
Power Supplies
PS5R Standard Series
Specifications
Output Capacity
Input Voltage (singlephase, 2-wire)
PS5R-B05*
PS5R-B12
PS5R-B24
15W
—
PS5R-C12
PS5R-C24
30W
Inrush Current
50A maximum (at cold start at 200V AC)
0.3A at
100V AC
2A
0.68A at 100V
AC
3.15A
Leakage Current (at no
load)
Output
1.1A at
100V AC
3.15A
70A maximum
(at cold start at
230V AC)
PS5R-F24
120W
100 to 240V AC, 50/60Hz,
110 to 340V DC
1.8A at
100V AC
4A
4A at 100V AC
79% at 24V 83% at 24V
PS5R-TJ24
480W
3 phase:
320 to 575V AC
2 phase:
360 to 575V AC
3 x 1.1A
3 x 0.8A
6.3A
70A maximum (at cold start at
230V AC)
21A na
<3.5ml
85% at 24V
83% at 24V
91%
Automation Software
75% at 12V
75% at 24V
Overvoltage Protection
Outputs turns off at 105% (typical)
5V, 1.5A
12V, 0.6A
24V, 0.3A
5V, 2.5A
12V, 1.2A
24V, 0.6A
12V, 2.5A
24V, 1.3A
Voltage Adjustments
Output Holding Time
Rise Time
Line Regulation
Load Regulation
Fluctuation due to Ambient Temperature Change
Ripple Voltage
24V, 2.1A
24V, 3.1A
24V, 4.2A
24V, 5A
24V, 10A
±10% (V.ADJ screw on top)
20ms minimum (at full rated input and output)
200ms maximum (at full rated input and output)
0.4% maximum
1.5% maximum
150ms max.
24V, 20A
10ms typical
?
1.0% max
2.0% max
0.05% maximum
2% peak to peak maximum (including noise)
120% typical (Zener-limiting)
PS5R-A
PS5R-B
No
Dielectric Strength
Insulation Resistance
LED (green)
PS5R-Q
PS5R-E
Yes
No
Between input and output terminals: 3,000V AC, 1 minute
Between input terminals and housing: 2,000V AC, 1 minute
Between output terminal and housing: 500V AC, 1 minute
PS5R-D
PS5R-F
PS5R-G
Yes
Yes
2kV AC, 500V
DG
Between input and output terminals/input terminals and housing: 100MΩ minimum (500V DC megger)
–10˚ to +60˚C (14˚ to 140˚F) (see derating curves)
–30˚ to +85˚C (-22˚ to 185˚F)
Operating Humidity
-25 to +70 C
-40 to +85 C
95% max (at 25
C, no
condensation)
<15Hz amplitude
+/- 2.5mm in
accordance with
IEC 60068-2-6 15
to 150Hz, 2.3g,
90 min.
30g in all
directions in accordance with IEC
60068-2-27
20 to 90% relative humidity (no condensation)
45m/s2, 10 to 55Hz, 2 hours on each of 3 axes
300m/s2 (30G), 3 shocks in each of 6 directions
Conforms to EMC Directives EN50081-2 & EN50082-2. LVD Directive EN60529 — Certified to EN60950.
UL508 listed. c-UL, TUV approved. CE marked. EN61000-3-2
Weight
150g
170g
360g
390g
800g
600g
1200g
Termination
Spring-up, fingersafe terminals with captive M3.5 screws
IP protection
IP20 (finger safe)
Dimensions H x W x D (mm)
75 x 45 x 70
75 x 45 x95
75 x 90 x 95
75 x 90 x 95 120 x 85 x 140 75 x 145 x 95
120 x 115 x140
2.95 x 3.54 x
2.95 x 3.54 4.72 x 3.35 x
4.72 x 4.53 x
Dimensions H x W x D (inches) 2.95 x 1.77 x 2.76 2.95 x 1.77 x 3.74
2.95 x 5.71 x 3.74
3.74
x 3.74
5.52
5.52
Communication
Shock Resistance
10 to 50Hz, 0.75mm p-p, 2 hrs on each of 3 axes
Sensors
Operating Temperature
Storage Temperature
Vibration Resistance
< 10mVpp
125% typical,
auto reset
120% typical, auto reset
PS5R-C
Power Supplies
Operation Indicator
Parallel Operation
Allowed
1.15A at
100V AC
3.15A
—
—
PS5R-G24
240W
0.75mA maximum (60Hz, measured in conformance with UL, CSA, VDE)
69% at 5V
75% at 12V
79% at 24V
Typical Efficiency
Overload Protection
PS5R-Q24
75W
—
—
PS5R-E24
100W
100 to 120V AC,
50/60Hz
200 to 240V AC,
50/60Hz
(jumper selectable)
240 to 370V DC
2.5A at 100V AC
1.5A at 200V AC
4A
50A maximum (at
cold start at 200V
AC)
PLCs
Internal Fuse Rating
Voltage and Current
Ratings
—
—
PS5R-D24
50W
100 to 240V AC nominal (85 to 264V AC), 50/60Hz (47 to 63Hz)
110 to 340V DC nominal (105 to 370V DC)
0.17A at
100V AC
2A
Input Current (typical)
Input
PS5R-A05
PS5R-A12
PS5R-A24
7.5W
OI Touchscreens
Model
Approvals
1705151126
120 x 200x 140
4.72 x 7.87 x
5.51
2000g
130 x 115 x 152.5
5.12 x 4.53 x 6.00
Barriers
1. For dimensions, see page 192.
2. For usage instructions, see page 191.
2000g
3. *12.5W for 5VDC model.
800-262-IDEC (4332) • USA & Canada
189
Power Supplies
Temperature Derating Curves
PS5R-A/B
PS5R-C/D
Mounting style B
70
70
Output Current (%)
80
80
60
50
40
30
60
50
40
30
20
20
10
10
0
10
20
30
40
50
Mounting style A
90
Mounting style A
90
0
–10
Mounting style B
100
100
Output Current (%)
PLCs
OI Touchscreens
PS5R Standard Series
0
–10
60
0
Mounting style A
Output Current (%)
60
50
40
30
20
Mounting style B
70
60
50
40
30
10
0
10
20
30
40
50
0
60
0
Operating Temperature (°C)
Sensors
PS5R-F/G
Mounting Style B
Mounting Style A
20
30
40
50
60
PS5R-TJ
100
100
90
90
80
Output Current (A)
70
Output Current (%)
10
Operating Temperature (C)
80
Communication
Mouting style A
20
10
60
50
40
30
20
70
60
50
Iw 40
30
20
10
10
0
10
20
30 35 40
50
0
60
Operating Temperature (C)
A Mounting (standard)
Barriers
60
80
70
0
10
20
30
40
50
60
70
Ambient Temperature (C)
B Mounting (Facing Upward)
Vertical
190 50
90
80
0
30 35 40
100
90
0
-10
20
PS5R-Q
Mounting style B
100
Output Current (%)
Power Supplies
Automation Software
Operating Temperature (C)
PS5R-E
10
Operating Temperature (C)
Vertical
www.IDEC.com
1705151126
Power Supplies
Overcurrent Protection Characteristics
PS5R-A/B
Part Numbers: PS5R Accessories
Description
Part Number
DIN rail (1000mm)
BNDN1000
BNL5
50
0
Output Current (%)
PLCs
DIN rail end clip
100
Output Voltage (%)
Appearance
OI Touchscreens
Accessories
PS5R Standard Series
100 105
PS5R-C/D/E
Installation Instructions
100
Time-Saving Spring-up Terminals
Output Voltage (%)
Automation Software
The innovative terminals on the PS5R series use a spring-loaded screw. This
makes installation as easy as pushing down and turning with a screwdriver. Installation time is cut in half since the screws do not need to be backed out to install
wiring. The screws are held captive once installed and are 100% finger-safe.
Screw terminals accept bare wire or ring or fork connectors.
50
1. Insert the wire connector into the slot on the side of the power supply.
0
Output Current (%)
100 105
Power Supplies
Parallel Operation
2. Using a flat head or Phillips screwdriver, push down and turn
the screw.
PS5R
Front Panel (terminals)
Adjusts within ±10%; turn clockwise
to increase output voltage
DC ON
Operation
indicator
Green LED is lit when output voltage
is on
+V, –V
DC output
terminals
+V: Positive output Terminal
–V: Negative output terminal
Frame
ground
Ground this terminal to reduce
high-frequency currents caused by
switching
L, N
Input
terminals
Accept a wide range of voltages and
frequencies (no polarity at DC input)
NC
No connection
Do not insert wires here, as this may
damage the power supply
+
-
PS5R
PS5R
PS5R
Communication
Voltage
adjustment
Sensors
V. ADJ
TERMINALS
The wire is now connected, and the screw terminal is fingersafe!
ELECTRICAL LOAD
PS5R
1. Parallel operation only recommended for PS5R-Q24, PS5R-F24 and PS5R-G24.
2. Factory recommended diode ST Microelectronics BYV54V-50, BYV54V-100,
BYV54V-200, BYV541V-200 or with equivalent electrical specifications.
3. Using the voltage adjustment make sure out-voltage is the same for all power
supplies.
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
191
Power Supplies
Dimensions
PS5R-B (15W)
13
90
80
13
13
60
75
DC ON
DC ON
V.ADJ
V.ADJ
13
75
62.5
60
75
62.5
60
.5
6.5
-ø 4-ø4
M3.5 Terminal Screws
DC ON
PS5R-C (30W)
M3.5 Terminal
Screws
7.35
PS5R-A (7.5W)
10
OI Touchscreens
PS5R Standard Series
M3.5 Terminal
Screws
PS5R-Q (75W)
13 13 13 M3.5 Terminal Screws
13 13 16 13 13
M3.5 Terminal
Screws
101
110
120
101
110
120
13 13
DC ON
12
PS5R-F (120W)
60
75
13 13
90
80
7.35
6.5 .5
-ø 4-ø4
10
Automation Software
PS5R-D (50W)
12
35
38.5
7.35
7.35
12
35
38.5
R2
.2
6-ø 5
6.5
R2
.2
6-ø 5
6.5
5
PLCs
V.ADJ
M3.5 Terminal
Screws
12
4.5
5
Power Supplies
V.ADJ
.5
ø4
4-
4-ø
75
85
PS5R-E (100W)
PS5R-G (240W)
145
135
PS5R-TJ24
M3.5 Terminal
Screws
115
4.5
190
200
4-ø
.5
200-240V
4ø4
5
12
M3.5 Terminal
Screws
130
102
110
120
Sensors
75
60
14
-ø
6.5
4.6
13 13 26 13 13
105
115
Communication
Terminal Markings
PS5R-A/B
-V
NC
PS5R-C/D/Q/F/G
+V
PS5R-E
NC
–V
–V
+V
DC ON
DC ON
DC ON
Barriers
V.ADJ
L
N
NC
100w-OUTPUT
V.ADJ
V.ADJ
INPUT
+V
INPUT
L
N
INPUT
L
N
VOLTAGE SELECT
200-240V
100-120V
NC
200-240V
192 www.IDEC.com
1705151126
Power Supplies
PS3X
OI Touchscreens
PS3X Series
Key features:
• Compact size
• Universal AC input voltage
• 5V, 12V and 24V DC outputs
• Available with mounting brackets for direct or DIN rail mounting
• Overcurrent/overvoltage protection
• EMC, EN55022 Class B compliant
• UL/c-UL recognized, TUV
PLCs
Part Numbers
Power Supply
Output
Capacity
 15W
 25W
Input
Output
Voltage Voltage
Output
Current
PS3X-B05AFC
PS3X-B12AFC
PS3X-B24AFC
 5V
12V
24V
3.0A
1.3A
0.63A
PS3X-C05AFC
PS3X-C12AFC
PS3X-C24AFC
 5V
12V
24V
5.0A
2.1A
1.1A
PS3X-D12AFG
PS3X-D24AFG
12V
24V
4.2A
2.2A
100 to
240V AC
 75W
DIN-rail Mounting Bracket (optional)
Applicable Power Supply
PS3X-B
PS3X-C
PS3X-D
PS3X-Q
PS3X-E
 5V
12V
24V
12.0A
6.0A
3.2A
16.0A
8.5A
4.5A
Appearance
PS9Z-3N4B
PS9Z-3E4C
PS9Z-3E4D
Length
Material
Weight (g)
BNDN1000
1000mm
Aluminum
200
End Clips
Appearance Part Number Description
BNL5
small DIN rail end clip
BNL6
medium DIN rail end clip (the BNL6 has a
higher profile than BNL5)
Cover and Terminal Style
C: w/Standard cover,
Horizontal terminal block
(PS3X-B/C models)
G: w/Standard cover,
Vertical terminal block
(PS3X-D/Q/E models)
800-262-IDEC (4332) • USA & Canada
Barriers
Input Voltage
AF: 100 to 240V AC
Communication
PS3X - B 05 AF C
1705151126
Part Number
Part Number
Part Number Configuration
Output Capacity
B:15W
C:25W
D:50W
Q:75W
E:100W
Output Voltage
05: 5V DC (15W, 25W, 75W, 100W)
12: 12V DC
24: 24V DC
PS9Z-3N3E
DIN Rail
 5V
12V
24V
PS3X-E05AFG
PS3X-E12AFG
PS3X-E24AFG
Part Number
PS9Z-3N3A
PS9Z-3N3B
PS9Z-3E3B
Sensors
100W
PS3X-Q05AFG
PS3X-Q12AFG
PS3X-Q24AFG
Applicable Power Supply
PS3X-B
PS3X-C
PS3X-D
PS3X-Q
PS3X-E
Power Supplies
 50W
Part Number
Automation Software
Style
L-shaped Mounting Bracket (optional)
193
Power Supplies
Specifications
[15W]
PS3X-B05/B12/B24
Model
Voltage Range (Note 1)
PLCs
Frequency
Input Current
Inrush Current
(Ta = –25°C,
ACV cold start)
Leakage Current
at 115V AC
Efficiency (Typ.)
(230V AC at input/
rated output)
 5V
12V
24V
at 230V AC
Rated Voltage/Current
Automation Software
Adjustable Voltage Range
Output Holding Time
Start Time
Ripple (including noise)
Input Fluctuation
Overvoltage Fluctuation
Temperature Fluctuation
Regulation
Dielectric Supplementary
Strength
Functions
Sensors
Power Supplies
Output
Rise Time
–20 to –10°C
–10 to 0°C
PS3X-B, C: 0 to +50°C
PS3X-D, Q, E: 0 to +45°C
Communication
[50W]
PS3X-D12/D24
100 to 240V AC
85 to 264V AC/
120 to 375V DC
Overvoltage Protection
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Vibration Resistance
Shock Resistance
EMI
EMS
EMC
Safety Standards
Dimensions (H × W × D) (mm)
Weight (approx.)
Terminal Screw
[100W]
PS3X-E05/E12/E24
0.65A max.
30A max.
47 to 63 Hz
1.3A max.
30A max.
1.8A max.
30A max.
2.5A max.
35A max.
60A max.
50A max.
50A max.
50A max.
70A max.
0.5mA max.
77%
81%
82%
5V, 3A
12V, 1.3A
24V, 0.63A
1.5mA max.
77%
81%
84%
5V, 5A
12V, 2.1A
24V, 1.1A
0.5A max.
40A max.
1.5mA max.
1.5mA max.
1.5mA max.
—
77%
77%
81%
82%
81%
84%
84%
84%
—
5V, 12A
5V, 16A
12V, 4.2A
12V, 6A
12V, 8.5A
24V, 2.2A
24V, 3.2A
24V, 4.5A
±10%
13 ms typ. (100V AC)
10 ms typ. (100V AC)
23 ms typ. (100V AC)
14 ms typ. (100V AC)
17 ms typ. (100V AC)
60 ms minimum
60 ms minimum
60 ms minimum
60 ms minimum
80 ms minimum
(230V AC)
(230V AC)
(230V AC)
(230V AC)
(230V AC)
1000 ms max. (230V AC input, rated output)
50 ms max.
30 ms max.
30 ms max.
30 ms max.
30 ms max.
(230V AC input, rated
(230V AC input, rated
(230V AC input, rated
(230V AC input, rated
(230V AC input, rated
output)
output)
output)
output)
output)
0.5% max.
5V: ±2% max. 12V, 24V: ±1% max.
0.04% / °C max. (–20 to +50°C)
0.04% / °C max. (–10 to +45°C)
  5V: 140mV max.
  5V: 200mV max.
12V: 240mV max.
–
–
–
12V/24V: 200mV max.
24V: 300mV max.
  5V: 140mV max.
  5V: 140mV max.
  5V: 160mV max.
  5V: 160mV max.
12V: 240mV max.
12V: 240mV max.
12V: 240mV max.
12V: 240mV max.
12V/24V: 200mV max.
24V: 300mV max.
24V: 300mV max.
24V: 300mV max.
24V: 300mV max.
  5V:   70mV max.
  5V:   70mV max.
  5V: 100mV max.
  5V: 100mV max.
12V: 120mV max.
12V: 120mV max.
12V: 120mV max.
12V: 120mV max.
12V/24V: 150mV max.
24V: 150mV max.
24V: 150mV max.
24V: 150mV max.
24V: 150mV max.
105% min. (auto reset) 2
Voltage limitation at 115% min.
Operation Indicator
Between input and output terminals
Between input and ground terminals
Between output and ground terminals
[75W]
PS3X-Q05/Q12/Q24
88 to 264V AC / 125 to 375V DC
Overcurrent Protection
Insulation Resistance
Barriers
[25W]
PS3X-C05/C12/C24
Rated Input Voltage
Input
OI Touchscreens
PS3X
Intermittent operation or output off at 115% min. 3
green LED
3000V AC, 1 minute
2000V AC, 1 minute
500V DC, 1 minute
100MΩ minimum, 500V DC megger
(between input and output terminals, between input and ground terminals)
–20 to +70°C (no freezing, see output derating)
–10 to +70°C (no freezing, see output derating)
20 to 85% RH (no condensation)
–40 to +85°C (no freezing)
10 to 95% RH (no condensation)
10 to 55 Hz, 20m/s2 constant, 2 hours each in 3 axes
200m/s2, 1 shock each in 3 axes
EN55022 Class B
EN55024
IEC/EN60950-1, UL60950-1, CSA C22.2 No. 60950-1
50.8H × 28W × 62D
50.8H × 28.5W × 79D
82H × 35W × 99D
95H × 38W × 129D
95H × 38W × 159D
130g
180g
340g
500g
700g
M3
M3.5
1. See “Output Current vs. Input Voltage” characteristics next page. Not subject to safety standards. When using DC input, connect a fuse to the input terminal for DC input protection.
2. Overload for 30 seconds or longer may damage the internal elements.
3. One minute after the output has been turned off, turn on the AC input again.
194 www.IDEC.com
1705151126
Power Supplies
PS3X
Operating Temperature vs. Output Current (Derating Curves)
OI Touchscreens
Characteristics
Overcurrent Protection Characteristics
Conditions: Natural air cooling (operating temperature is the temperature around the power supply)
PS3X-D/Q/E
PS3X
90
90
80
80
80
70
70
70
60
50
40
30
20
10
60
50
40
37.5
30
20
10
0
-30 -20 -10
0
10
20
30
40
50
60
60
50
40
30
20
10
0
0
70
100
Intermittent Operation
90
Output Voltage (%)
100
Output Current (%)
100
Output Current (%)
100
PLCs
Output Current (%)
PS3X-B/C
-10
Operating Temperature (°C)
0
10
20
30
40
50
60
-10
70
Operating Temperature (°C)
0
0
10
20
30
40
50
0Operating
Temperature
(°C)
Output
Current (%)
60
100
70
105
PS3X-D/Q/E
100
100
90
90
90
80
80
80
70
70
70
60
50
40
30
20
60
50
40
30
20
10
0
PS3X-B: 85 100
PS3X-C: 88 100
Input Voltage (VAC)
264
264
0
60
50
40
30
20
10
88 100
264
Input Voltage (VAC)
0
88
176
Input Voltage (VAC)
Power Supplies
10
Output Current (%)
100
Output Current (%)
Output Current (%)
PS3X-B/C
Automation Software
Output Current vs. Input Voltage (TA = 25°C)
132
264
Operating Temperature by Safety Standards
Power Supplies
Up
UL/EN60950-1
Mounting A, B
50°C
PS3X-D12, -D24
PS3X-Q05, -Q12, -Q24
PS3X-E05, -E12, -E24
45°C
Mounting A
(standard)
Sensors
PS3X-B05, -B12, -B24
PS3X-C05, -C12, -C24
Mounting B
Note: Observe the derating curves when operating PS3X power supplies.
Communication
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
195
Power Supplies
Dimensions
11.4
15.1
39.1
62.0
65.0
Output Voltage
Adjustment
18.0
82.0
74.0
99.0
2-M3 (Depth 2.5
to 4.0 mm max.)
2-M3 (Depth 2.5
to 4.0 mm max.)
9.5
(Terminal Centers)
95.0
LED
38.0
159.0
3-M3
(Depth 2.5 to
4.0 mm max.)
10.0
10.5
19.0
18.0
38.0
118.0
18.0
22.0
Output Voltage
Adjustment
77.0
19.5
2-M3 (Depth 2.5
to 4.0 mm max.)
7-M3.5
(Terminal Screw)
2-M3 (Depth 2.5
to 4.0 mm max.)
129.0
3-M3
(Depth 2.5 to
4.0 mm max.)
162.6
78.0
32.0
33.0
34.0
LED
5-M3
(Terminal Screw)
Output Voltage
32.0
Adjustment
24.0
95.0
78.0
Terminal
Cover
129.3
)
Power Supplies
5-M3
(Terminal Screw)
PS3X-E
9.5
(Terminal Centers)
Automation Software
Terminal
Cover
LED
2-M3 (Depth 2.5
to 4.0 mm max.)
79.0
2-M3 (Depth 2.5
to 4.0 mm max.)
PS3X-Q
25.4
LED
5-M3
(Terminal Screw)
Output Voltage
11.0
Adjustment
14.5
Output Voltage
Adjustment
2-M3 (Depth 2.5
to 4.0 mm max.)
28
PLCs
5-M3
(Terminal Screw)
2-M3
(Depth 2.5 to
4.0 mm max.)
28.5
25.25
LED
99.7
55.0
20.5
45.5
Terminal
Cover
91.9
55.0
35.0
13.0
50.8
8.25
Terminal Cover
17.5
76.0
39.1
50.8
Terminal Cover
PS3X-D
9.5
(Terminal Centers)
PS3X-C
7.62
(Terminal Centers)
PS3X-B
7.62
(Terminal Centers)
OI Touchscreens
PS3X
Marking
Name
L, N
AC Input Terminal
Terminal Markings
Sensors
PS3X-B/C
PS3X-D/Q
PS3X-E
L
N
L
L
N
N
−V
–V
+V
+V
V.ADJ
LED
V.ADJ
LED
+V, –V
−V
V.ADJ
+V
V.ADJ
LED
DC Output Terminals
Output Voltage
Adjustment
Power status
LED
Barriers
Communication
Ground Terminal
Description
Accepts a wide range of voltage and
frequency. Polarity does not matter when
using DC input.
Be sure to connect this terminal to a
proper ground.
Positive and negative output terminals
Allows adjustment within ±10%. Turning
clockwise increases the output voltage.
Illuminates (green) when input power is
applied.
196 www.IDEC.com
1705151126
Power Supplies
PS3X
L-shaped Mounting Bracket
26
4-ø3.5 holes
16.5
30.0
14.0
4-ø3.5 holes
65.0
83.5
3.5
13.5
±0.5
3.5
20.0
28.0
17.5
2-ø
6.5
2.3
27.0
20.0
10.0
ho
les
4.0
PLCs
PS9Z-3E3B (for 50W)
22.0
4-ø
3.5
ho
les
PS9Z-3N3E (for 75W/100W)
3-ø3.5 holes
3-ø4.5 holes
25.0
118.0
77.0
15.5
31.0
13.5
4-ø3.5 holes
4-ø4.5 holes
22.5
ho
les
3.5 × 4.5
oblong hole
7.5
42.5
15.0
28.0
2.0
.5
10.0
18.0
7.0
ø3
28.0
17.5
4.5
100.0 ±0.3
157.5
10.0
6.5
2.3
18.0
Automation Software
74.0
80.0 ±0.3
103.0
34.5
12.5
±0.3
±0.2
2.0
6.5
72.0
20.0
27.0
14
PS9Z-3N3B (for 25W)
41
39.1
OI Touchscreens
PS9Z-3N3A (for 15W)
2-C2.0
10.0
DIN-rail Mounting Bracket
H1
H3
35
PS9Z-3E4C
H2
L3
PS9Z-3N4B
L1
L2
PS9Z-3E4D
L1
L2
L3
H1
PS3X-B
95
105.5
35
5.2 20.5 50.8
H2
113
Power Supplies
Part Number Applicable Power Supply
H3
PS3X-C
95
35
5.2 20.5 50.8
PS3X-D
136 117*
35
5.2 20.5 82
PS3X-Q
188 141*
39.5 5.2 19.7 95
PS3X-E
188 173*
39.5 5.2 19.7 95
* Note that L2 is shorter than L1.
Sensors
Communication
Barriers
1705151126
800-262-IDEC (4332) • USA & Canada
197
Power Supplies
Instructions
Installation Notes
3. Use M3 screws for mounting.
Choose screws that protrude 2.5 to
4mm from the surface of the
switching power supply.
Mounting A
(standard)
4. Do not cover the openings of the
switching power supply. Ensure proper
heat dissipation by convection.
Mounting B
Overcurrent Protection
Chassis
Mounting
Panel
Mounting
Screw
Automation Software
Power Supplies
Sensors
6. When derating of the output does not work, provide forced air-cooling.
Overvoltage Protection
PS3X-B/C: Voltage limit and auto-recovery method. The switching power supplies operate normally when voltage returns to normal.
Series Operation
When connecting two switching power supplies in a series, insert a Schottky
diode to each output.
7. Make sure to wire the ground terminal correctly.
8. For wiring, use wires with heat resistance of 60°C or higher.
Use copper wire.
Parallel Operation
Parallel operation is not possible.
9. Recommended tightening torque of terminal screws: 0.8 N·m
Insulation/Dielectric Test
When performing an insulation/dielectric test, short the input (between AC) and
output (between + and –). Do not apply or interrupt the voltage suddenly, otherwise surge voltage may be generated and the power supply may be damaged.
Safety Precautions
cident or failure may occur.
• Do not use switching power supplies with equipment where failure or inadvertent operation may harm anyone, such as medical, aerospace, railway,
nuclear, etc. PS3X switching power supplies are designed for use in general
electric equipment such as office, communication, measuring, and industrial
electric devices.
• Observe the temperature derating curves. Operating temperature refers to
the temperature around the lower part of the switching power supply. Failure
to observe the derating curves could result in an internal temperature rise
and possible failure of the switching power supply.
• Do not disassemble, repair, or modify the power supplies, otherwise electric
shock, fire, or failure may occur.
• The fuse inside the switching power supply is for AC input. When using with
DC input, install an external fuse.
• Do not install the switching power supply in places where someone will
touch it when input voltage is applied. Do not touch the switching power
supply while input voltage is applied and right after the power is turned off,
because high temperature and high voltage may cause burns and electric
shocks.
• Do not set the V. ADJ control over the setting range, otherwise performance
deterioration or failure may occur.
• Do not short circuit the output terminals or output lead wires, otherwise fire
or damage may occur.
Communication
The output voltage drops automatically when an overcurrent flows, resulting in
intermittent operation. Normal voltage is automatically restored when the load
returns to normal conditions. However, overcurrent for a prolonged period of
time or short-circuit causes the internal elements to deteriorate or break down.
PS3X-D/Q/E: The output is turned off when an overvoltage is applied. When the
output voltage has dropped due to an overvoltage, turn the input off, and after
one minute, turn the input on again.
5. Maintain a minimum of 20mm clearance around the power supply.
• Provide the final product with protection against failure or damage that may
be caused by malfunction of the switching power supply. Damaged switching
power supply may cause overvoltage on the output terminals, or may cause
voltage drop.
• Turn off power before wiring. Also, make sure to wire correctly. Improper
wiring may cause electric fire or damage.
• Do not use switching power supplies to charge rechargeable batteries.
Barriers
Adjustment of Output Voltage
The output voltage can be adjusted within ±10% of the rated output voltage
by using the V.ADJ control. Turning the V.ADJ clockwise increases the output
voltage. Turning counterclockwise decreases the output voltage. Note that
overvoltage protection may work when increasing the output voltage.
1. When mounting the PS3X
switching power supply, see
the figure on the right.
2. See dimension drawings for mounting
hole layouts.
PLCs
Up
2.5 to 4 mm
OI Touchscreens
PS3X
• When failure or error occurs, shut down the input to the switching power
supply, and contact IDEC.
• Do not use or store the switching power supply in a place subject to extreme
vibration or shocks, otherwise failure will result.
• Do not use the switching power supply where it is subject to or near:
• Direct sunlight, heat or high temperatures
• Metal powder, oil, chemicals or hydrogen sulfide
• Highly humid areas, such as a basement or conservatory
• Inside freezers or refrigerators, near cooler exhaust, or other cold
environments
• Make sure that the input voltage does not exceed the rating. Note polarity
of input and output terminals and wire correctly. Incorrect wiring may cause
blown fuses (AC input power), smoke or fire.
• Do not touch the inside of the switching power supply, and make sure that
foreign objects do not enter the switching power supply, otherwise an ac-
198 www.IDEC.com
1705151126
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising