Saplings glider swinging crib Components – parts

Saplings glider swinging crib Components – parts
Saplings glider swinging crib
1
Assembly instructions – please keep for future reference
Components – parts
4a
1
4b
Crib feetX2
2
CRIB ENDS X 2
Swinging arms
without locking
bolt holes x2
6
9
3
CENTRE CROSS BAR X 1
Swinging arm side
bars x2
7
CRIB SIDES X 2
Swinging arms
with locking bolt
holes x2
8
BASE BOARD X 1
Crib base end
supports x2
If you need help or have missing or damaged parts, call the customer helpline:
01952 550022
2
Components–fittings
please check all fittings are present
PRESENT BEFORE ASSEM
X8
Assembly instructions
Stage 1 assembly of the feet
Push metal sleeves (part D) x8 onto mechanisms on bottom of crib
end part 2 and top of crib feet part 1 Attach the crib feet ends (part 1)
to the cross bar (part 3) by placing the large barrel nuts (E) into the
large holes provided and attach with 2 x large bolts (A). Ensuring that
the METAL SLEEVE on the feet ends is facing on the outside of the
crib.
Stage 2 assembly of the glider arms
Attach 1 x swinging arm with locking bolt hole (part 4a) to 1 x
swinging arm side bar (part 6) by placing 1 x small barrel nut (part C)
into the hole provided and attach using 1 x large bolt (part A). Then
attach 1 x swinging arm (part 4b) to the other end of the swinging arm
side bar (part 6) by placing 1 x small barrel nut (part C) into the hole
provided and attach using 1 x large bolt (part A). Repeat procedure for
the other swinging arm side bar. Attach the swinging arms and side
bars (part 4a, part 4b and part 6) to the crib feet ends (part 1) using 4
small bolts (part B) and inserting 1 washer (part H) between the
swinging arms and metal sleeve (figure 1).ensure locking arm (part
4a) are on diagonal corners of crib feet so locking peg holes line up
with holes on crib ends at (stage 4).
Assembly instructions
Figure 1
Stage 3 assembling of the crib body
Place 1 x crib end (part 2) on the floor with the screw inserts holes
facing upwards. Loosely attach 2 x crib sides (part 7) to the crib end
(part 2) using 4 x large bolts (part A). Making sure the grooves on the
sides are inside and at the bottom. Attach 1 x crib base support end
(part 9) to the mattress base (part 8) gently slide the mattress base
(part 8) into the grooves on the crib sides (part 7) so that the base
support end meets the crib end.
PLEASE PLACE THE MATTRESS BASE IN THE CORRECT POSITION, SO THAT THE
TWO SAFETY LABELS ARE FACING UPWARDS Attach the other base
support end (part 9) onto the other end/top end of the mattress base.
Place the 2nd crib end (part 2) onto the crib sides by using 4 x large
bolts (part A). As in (figure 2) PLEASE ENSURE THAT THE BASE IS
FULLY ENGAGED INTO GROOVES BEFORE TIGHTENING) .
3
4
Assembly instructions
Figure 2
Stage 4 attaching the crib body to the feet
Stage attaching the crib body to the feet
Place the crib frame over the crib stand resting it on top. Secure the
crib by placing 4 x small bolts (part B) through the swinging arms (parts
4a & part 4b) and through washer then into metal sleeve (part D) and
screw into mechanism. Repeat this procedure on all four corners.
ENSURE THE LOCKING BOLT HOLES ON THE CRIB ENDS AND SWINGING ARMS
LINE UP CORRECTLY
REQUIRED TOOLS:
Flat bladed screwdriver (not
included)
In the unlikely event that this
product has missing or damaged
parts, please call HELPLINE
01952 550022 to obtain spares.
Safety and care advice
Ensure that the Crib is used on a horizontal floor.
 Do not allow children to play unsupervised in the vicinity of the Crib
 WARNING: Ensure the Crib is in the locked position when leaving a child
unsupervised in it
 You should not fix any toy or decoration to the inside of the Crib that
could provide a foothold and present a danger of strangulation or
suffocation.
 The safety of the Crib could be adversely affected by fitting flammable
drapes.
 When a child is able to sit, Kneel or to pull itself up, the crib shall not be
used anymore for this child.
 Do not use the body of the crib without its frame.
 The upper surface of any mattress used should be at least 200mm from
the upper edge of the crib sides in its higher position.
 The crib should not be used if any parts are lost or damaged.
 Only Saplings spares should be used.
 Beware of the risk of open fires and other sources of strong heat, such as
electric bar fires, gas fires, etc. In the vicinity of the cot.
 All assembly fittings should always be tightened properly and care should
be taken that no screws are loose, because a child could trap parts of the
body or clothing (e.g. strings, necklaces, ribbons for babies dummies),
which could pose a risk of suffocation and strangulation.
 The recommended mattress for this crib is a Saplings “Crib” mattress
(90cm x 40cm)
 Any mattress used with this crib should be no more than 40mm shorter or
narrower than the length or width of the crib.
Scuff marks may be removed with a damp cloth. Occasional use of furniture
polish will maintain the good looks of your crib. Periodically check all screw
fixings to ensure they remain tight. Never clean with abrasive, ammonia
based, bleach based or split type cleaners.
THIS PRODUCT CONFORMS TO BSEN 1130-1:1997
FOR FURTHER ACCESSORIES FOR THIS PRODUCT PLEASE VISIT OUR WEBSITE AT
WWW.SAPLINGS.COM.
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising