Control Systems

Control Systems

C ontr ol Syyst ems

Lithonia Lighting produces a wide range of control systems for both architectural dimming and lighting energy management. These systems are suitable for applications in high-rise office buildings, educational facilities, multi-building complexes, manufacturing plants and sports facilities.

Lighting controls dramatically enhance efficiency by governing the amount of light needed to maintain illuminance levels and by limiting light use to occupied spaces. Lithonia offers a variety of lighting control solutions to meet ASHRAE 90.1 and similar legislation requirements.

652 www.lithonia.com

PSG9

657

659

657

663

Lighting

Control Systems

System Overview

PC Software

Digital Wallstations

Digital Equinox®

Dry Contact Switches

SweepSwitch®

Relay and Dimming Panels

Controllable Breaker Panels

System Accessories

654

656

657

659

662

662

663

669

670

671

672

PSG9

669 671

Sequel IDC

DSD

ISD

675

677

678

676

672 677

680

Application

Good

Building-wide Control

Energy Management - on/off only

Occupancy Sensors pages 672-674

SweepSwitch page 662

Energy Management - dimming

(Daylight Harvesting)

ISD DPC page 679

Timeclock control

SwitchPak page 671

Solution

Better

SwitchPak w/ SR option page 671

(on/off control only)

SwitchPak page 671

Digital Equinox page 660

Digital Equinox page 659

Best

Synergy MLX pages 654-670

(on/off and dimming control)

Synergy MLC or MLX pages 654-670

Synergy MLX pages 654-670

Synergy MLC pages 657-670 Synergy MLX pages 654-670

Architectural Dimming

Sequel IDC page 675 Synergy MLC pages 657-670 Synergy MLX pages 654-670

Wallbox Dimming

DSD page 677 ISD pages 678-679

Classroom Control

Occupancy Sensors pages 672-674

SweepSwitch page 662

SwitchPak page 671

Digital Equinox pages 659-660

University / College Campus

Occupancy Sensors pages 672-674 SwitchPak w/ SR option page 671

Sequel IDC page 675

Synergy MLX with Digital Equinox

pages 654-670, pages 659-660

Synergy MLX with Digital Equinox

pages 654-670, pages 659-660

LITHONIA CLITHONIA CLITHONIA CLITHONIA CLITHONIA C

ONTROL SYONTROL SYONTROL SYONTROL SYONTROL SY

STEMSSTEMSSTEMSSTEMSSTEMS www.lithonia.com

653

654

S y n e r g y

®

L i g h t i n g C o n t r o l S y s t e m O v e r v i e w

Fixture with step dimming option or with four-wire dimming ballast

Remote

Relay

(page 674)

Photocell

(page 661)

Occupancy

Sensor

(page 672-673)

Override

Switch

(page 662)

Photocell

(page 670)

Digital Equinox Station

Provides distributed fluorescent control. May be used stand-alone or as part of a fully integrated

Synergy ® system. (page 659-661)

Digital Remote Station

1 to 9 buttons in a single gang. Optional wireless receiver for operation and programming of presets from hand-held transmitter.

(page 658)

Preset Control

Station

4, 8, 12 and

16 channel master station with 6 to

16 preset lighting scenes. (page 657)

Local Area Network

Each system controller supports up to 60 digital stations.

System Controller

Plug-in unit provides for panel programming and operation, network communication, and astronomic timeclock. (page 665)

Controllable

Breaker

Provides individual controlof each circuit breaker and works with all standard Synergy ® controller and user interface options.

(page 669)

RS232 Interface

Local A/V system and laptop connection for programming and operation. (page 665)

Telephone Interface

(Optional) voice modem provides remote PC access and override of lighting via any touchtone telephone.

(page 665)

DMX Theatrical Control

(Optional) DMX interface allows

Synergy ® relays and dimmers to be controlled by theatrical systems.

(page 665) www.lithonia.com, keyword: Synergy

PSG9

P o w e r M o d u l e O p t i o n s

May be combined within the same enclosure to meet job site requirements

Occupancy

Sensor

(page 672-673)

Relay Module

Eight single-pole relays with zerocross switching, plus eight switch and two analog input terminals.

(page 666)

DALI Control Module

Network controllers and power supplies for three

DALI networks.

(page 667)

System Enclosure for Relays and Dimmers

Three capacities, up to

48 relays or 30 dimmers each.

(page 664)

Relays with Breakers

As above with either six

120V, four 277V or four

347V branch circuit breakers.

(page 666)

Ballast Control Module

Eight channels of 0-10VDC dimming with integrated 20A relays for four-wire dimming ballasts. Available with 120V,

277V and 347V circuit breakers.

(page 667)

Dimmer Module

Six universal load digital dimmers suitable for 120V or 277V incandescent, fluorescent, low voltage, neon, cold cathode and non-dim loads.

(page 666)

Tap Feed Lug Option

Allows several Synergy enclosures to share a single main feed up to 400 amps three phase. (page 668)

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

PSG9

Interactive Graphics

Monitor and control entire lighting system via virtualcontrol panel screens created with simple on-board tools, or import graphic image backgrounds and floorplans to suit project requirements. (page 656)

BACnet WAN

Allows over 4 million Synergy ® panels to interact as an integrated system using

BACnet, the ANSI and ISO standard for building automation.

Synergy ® CONFIG Software

Configure, control and monitor

Synergy ® lighting control panels on-site or remotely via phone lines or WAN with this easy-touse Windows ® application.

(page 656) www.lithonia.com, keyword: Synergy

655

System Configuration Software

SYSW CONFIG

Intended Use

PC-based Windows™ application used to configure a Synergy® system equipped with MLX controllers (page 665). Allows on-site or remote programming and configuration of all system parameters and schedules.

Features

Utilizes a familiar Windows™ graphical user interface to provide easy access to all system data. A simple tab-based navigation scheme allows the user to reach most configuration screens with a single click of the mouse. Access privileges for different software features can be set up for multiple users through the use of administrator-defined login IDs and passwords.

Online mode allows real-time monitoring and override of input and load status as well as diagnostic functions.

Connection to the system may be made with the supplied RS-232 cable through the front-mounted DB-9 connector on any system controller, or directly over the BACnet™ network (optional network interface card may need to be installed on PC). A connection may also be made from a remote site using standard telephone lines via the PHONE option on the controller (see page

665) and a PC equipped with a telephone modem.

Minimum hardware requirements are a 266MHz

Pentium™ II class PC running Windows™ 2000 or later operating system with 128 MB RAM, 30 MB free disk space and 800 x 600 video resolution.

Ordering Information

Series

SYSW CONFIG

Synergy® configuration software

656

Graphical Interface Software

SYSW GRAPHIC

Intended Use

Adds real-time control and monitoring capabilities to a Synergy® system through the use of a flexible graphical interface. Runs as a fully integrated component of the SYSW CONFIG software

(above) installed on a desktop, laptop or panel PC connected to the system via an RS-485, Ethernet or wireless network connection.

Features

Provides intuitive and interactive point-andclick control of loads with status feedback and remote diagnostic capability. Simple setup and configuration options allow the creation of floorplan-based, button-based or combination screens. Flexible control options allow graphical objects to directly monitor and override all system inputs (switches, photocells, digital stations), outputs (relays, dimmers, controllable breakers, DALI devices) room partitions and load groups. Integrated scheduling module allows the creation of temporary, PC-based schedules for special events.

Over 32,000 screens may be configured and the number of control objects per screen is limited only by screen resolution. Control screens may be user-configured in the field or ordered factory-prepared to client specifications via the SYSW

SCREEN accessory.

Ordering Information

Series

SYSW GRAPHIC

Synergy® graphical user interface

Accessories (Order separately)

SYSW SCREEN Factory-prepared SYSW GRAPHIC screen per user specifications. Indicate quantity of screens required.

LSA PC PC workstation suitable for system configuration or graphics. Contact factory for mounting and touchscreen options.

www.lithonia.com, keywords: SYSW CONFIG & SYSW GRAPHIC

PSG9

Intended Use

Provide manual dimming and preset lighting control for architectural dimming applications. Offered in a variety of styles and architectural finishes suitable for virtually any application. May be daisy-chained together with SYRS digital remote stations (page 658) for multi-location control.

Features

Functions – Master raise and lower buttons adjust the intensity of all lights dimmed from the station.

Channel raise and lower buttons adjust the intensity level of individual channels. LED bar graph displays intensity level. Select button saves presets and fade time is adjustable for each preset scene.

Preset button saves and activates presets. Off function turns off all channels.

Integral dry contact closure interface allows access to 16 presets and master raise/lower and off functions for A/V systems and auxiliary equipment.

Installation: 4- and 8-channel stations mount in

Lithonia #SQCS 5GB or RACO 699 five-gang backbox; 12- and 16- channel stations mount in Lithonia #SQCS 8GB backbox. Stations connect to a Synergy® system controller (page 665) via the four wire A4 control station network wire (page 670) which can be shared by up to 60 SQCS and SYRS

(page 658) wallstations per system controller.

Classification – Class 2 low voltage device.

Architectural Preset Control Station

SQCS

Ordering Information

Series

SQCS

Sequel® control station

Number of presets and channels

6P 4C

6 presets, 4 channels

6P 8C

6 presets, 8 channels

6P 12C

6 presets, 12 channels

6P 16C

6 presets, 16 channels

NOTES:

1 Additional delivery time and/or cost may be associated.

Finish

BJ4

Brushed stainless steel, black buttons

WC2

Painted white, white buttons

IE3

Painted ivory, ivory buttons

BL4

Painted black, black buttons 1

BF4

Polished brass, black buttons

1

Intended Use

Used in conjunction with a Synergy® system equipped with SYSC MLX controllers (page 665) to provide system-wide configuration, monitoring and override of lighting zones

Features

8.0" full-color TFT touchscreen graphical interface may be configured with floorplan-based or button-based screens. Flexible control options allow graphical objects to monitor and override any system input, output or load group as needed to satisfy project requirements. Screens may be field or factory configured.

Listings

UL Listed to US and Canadian safety standards.

Wallplate style

SD

Solid

TR

Translucent

Accessories (Order separately)

SQCS 5GB 5 gang backbox for 4-channel and 8-channel stations

SQCS 8GB 8 gang backbox for 12-channel and 16-channel stations

BKLE Engraved button cap (specify button color and wording)

Series Width Thickness Height Weight

SQCS 4C 10-1/8 (257) 1/4 (6) 4-5/8 (117) 2-1/2 (1.13)

SQCS 8C 10-1/8 (257) 1/4 (6) 4-5/8 (117) 2-1/2 (1.13)

SQCS 12C 15-7/16 (392) 1/4 (6) 4-5/8 (117) 4 (1.8)

SQCS 16C 15-7/16 (392) 1/4 (6) 4-5/8 (117) 4 (1.8)

Dimensions are shown in inches (millimeters) or pounds (kilograms) unless otherwise noted.

Graphical LCD User Interface

SYA LCD

Ordering Information

Series

SYA LCD 8.0" full color touch screen user interface (May be wall or panel mounted)

1

NOTES:

1 Other screen sizes and mounting options are available. Consult factory for information.

PSG9 www.lithonia.com, keywords: SQCS and SYA LCD

657

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

658

Digital Remote Wallstation

SYRS

Intended Use

Provides a convenient means to add pushbutton controls for on/off, preset, raise/lower, partition control or other user interface to a Synergy® lighting control system. IR option adds an infrared receiver for use with SYWR wireless remote transmitters (below).

Features

Stations are single gang, screwless appearance and are available with 1 to 9 buttons in a variety of painted and metallic finishes. Button caps can be engraved with labels having up to two lines of text. Buttons may be field configured via the Synergy® system controller (page 665) to satisfy a wide variety of project requirements. Integral

LED indicator on each button provides status. An optional infrared receiver adds capability for operation and programming of station functions from an accessory SYWR wireless hand held transmitter or programmer (below).

Installation: wallstation mounts in Lithonia

#SYRS 1GR or Steel City #52C13 plaster ring. Stations connect to a Synergy® system controller via the four wire SYA CABLEA4 (page 670) control station network wire which can be shared by up to 60 SYRS and SQCS (pages 657-658) stations per system controller.

Classification – Class 2 low voltage device.

Ordering Information

2-7/8

(73)

4-5/8

(117)

Series

SYRS

Number of gangs

1G

1 gang

Number of buttons

_BT

(1 to 9)

Finish

BJ4

Brushed stainless steel

WC2

Painted white

IE3

Painted ivory

BL4

Painted black 1

BF4

Polished brass 1

Options

IR

Infrared receiver, even number of buttons only.

Dimensions are shown in inches (millimeters) unless otherwise noted.

NOTES:

1 Additional delivery time and/or cost may be associated.

Infrared Wireless Transmitter and Scene Programmer

SYWR

Intended Use

Used for wireless remote control of lighting functions in a Synergy® system. Operates in conjunction with the optional infrared receiver on the SYRS digital remote wallstation (above). The

HHP version is useful in providing preset dimming control without the need for an SQCS control station.

Features

The SYWR 6B six-button transmitter provides remote activation of four presets, master raise/

7.75"

(19.7)

Ordering Information

5.45"

(13.8)

2.375"

(6)

1.25"

(3.2)

Series

SYWR

Type

6B

6-button remote transmitter

HHP

12-button hand-held programmer

1.77"

(4.49)

Accessories (Order separately)

SYRS 1GR Plaster ring, mounts to grounded 4" box (by others)

BKLE Engraved button cap (specify button color and wording) lower and master on/off. The SYWR HHP handheld programmer permits the saving and activation of 12 lighting preset scenes, the manual control of up to 12 dimming channels, master raise/lower and master on/off. Preset scenes configured and saved with the HHP may be recalled from buttons on the wallstation.

Dimensions are shown in inches (millimeters) unless otherwise noted.

www.lithonia.com, keywords: SYRS and SYWR

PSG9

Intended Use

Ideal for applications which require manual and automatic control of fluorescent or HID lighting equipped with compatible 4-wire (0-10V) electronic dimming ballasts. Wall-mounted control station provides local on/off, manual dimming and automated daylight dimming control in localized applications. May be used as a standalone room controller or connected to a Synergy® system for timeclock control and integration with a building automation system.

Features

Microprocessor-based wallstation incorporates one of the most advanced and easiest to configure daylight harvesting algorithms in the industry.

When used with Litronic® Series occupancy sensors (pages 672-673), all settings either adjust automatically to actual room usage or are set at the station, eliminating costly “ladder time” spent making adjustments on the sensors themselves.

Local switching is provided by LPCS Series power pack(s) (page 674), eliminating the need for home run wiring back to panel mounted relays.

When connected to a Synergy® system, all station buttons, inputs and outputs are fully programmable from the Synergy® controller or software and, like all Synergy® inputs and outputs, fully accessible to BACnet™ building automation systems. This allows daylight harvesting and dimming to be fully integrated into the building control system more simply and economically than ever before. Room switching and dimming parameters can be easily incorporated into a time schedule, dimming preset, or progressive load shedding strategy for maximum occupant comfort and energy savings.

Classification – Class 2 low voltage device.

Ordering Information

0-10V Dimming Wallstation

SYRS EXT

Digital Equinox®

Series

SYRS

Number of gangs

1G

1 gang

NOTES:

1 Additional delivery time and/or cost may be associated.

Occupancy

Synergy

'A4' network

(optional) sensor

Number of buttons

Stand-alone

3BT

3 buttons

Synergy®

1BT

1 button

3BT

3 buttons

5BT

5 buttons

7BT

7 buttons

9BT

9 buttons

Finish

BJ4 Brushed stainless steel

WC2 Painted white

IE3 Painted Ivory

BL4 Painted black 1

BF4 Polished brass 1

Line voltage branch circuit

SYRS

EXT

To next room

(up to 60 max per MLX controller)

LPCS power pack

0-10V Dimming signal

DEQ APS photocell

Line voltage to next room

Switched hot

Type

EXT

External inputs for occ. sensor and photocell, outputs for LCPS and 0-10V dimming ballast.

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

www.lithonia.com, keyword: SYRS EXT

PSG9

659

660

Dual Switch Wallstation

SYRS EXTDS

Digital Equinox®

Intended Use

Ideal for applications which require manual and automatic control of RT5™ fluorescent fixtures equipped with step-dimming ballasts, fluorescent fixtures wired for inboard/outboard switching or two independent lighting zones. Wallmounted control station provides local manual control with fully integrated occupancy sensor and photocell inputs for automated energy management. May be used as a stand-alone room controller or connected to a Synergy® system for timeclock control and integration with a building automation system.

Features

Microprocessor-based wallstation provides intuitive manual control of bi-level lighting. Compatible with all Litronic® Series occupancy sensors

(pages 672-673) for easy code compliance in a variety of applications.

Use LPCS Series power packs (page 674) to switch up to two full 20A circuits on each zone, eliminating the need for home run wiring back to panel mounted relays.

When connected to a Synergy® system, all station buttons, inputs and outputs are fully programmable from the Synergy® controller or software and, like all Synergy® inputs and outputs, fully accessible to BACnet™ building automation systems. This allows daylight harvesting and remote switching to be fully integrated into the building control system more simply and economically than ever before. Relays and buttons in each room can be easily incorporated into a time schedule, dimming preset or progressive load shedding strategy for maximum occupant comfort and energy savings.

Classification – Class 2 low voltage device.

Ordering Information

Series

SYRS

Number of gangs

1G

1 gang

NOTES:

1 Additional delivery time and/or cost may be associated.

Number of buttons

Stand-alone

4BT

4 buttons

Synergy®

2BT

2 buttons

4BT

4 buttons

6BT

6 buttons

9BT

9 buttons

Finish

BJ4

Brushed stainless steel, black buttons

WC2

Painted white, white buttons

IE3

Painted ivory, ivory buttons

BL4

Painted black, black buttons 1

BF4

Polished brass, black buttons 1

Type

EXTDS

External inputs for occ. sensor and photocell, two outputs for LCPS power packs.

Line voltage branch circuit

Qty.2

LPCS power packs

Line voltage to next room

Switched leg 'S1'

Switched leg 'S2'

RT5 fixture with step dimming option

DEQ APS photocell

Occupancy sensor

Synergy

'A4' network

(optional)

SYRS

EXT DS

To next room

(up to 60 max per MLX controller) www.lithonia.com, keyword: SYRS EXTDS

PSG9

Intended Use

Integrates a localized zone of fluorescent lighting equipped with compatible four-wire electronic dimming ballasts into a Synergy® system.

Plenum-mounted DEQ LC load controller provides on/off, dimming and automated daylight dimming control for a single lighting zone when a wall-mounted control station is not desired.

Features

The DEQ LC installs in the plenum above the area to be controlled in place of the cover on a standard 4” or 5” square junction box.

DEQ LC load controller acts as a hub for the connection of the low voltage DEQ APS photocell

(below), Litronic® occupancy sensor (pages 672-

673), LPCS power control station (page 674) and

0-10V dimmable ballast control leads. If desired, a standard wall switch can be used for local on/off operation making the control system totally unobtrusive to the user.

When connected to a part of a Synergy® system, the DEQ LC can share status, set point and override functions with all Synergy® system controllers, PC graphics and other building control systems through the BACnet™ protocol.

Digital Equinox® Load Controller

DEQ LC

Digital Equinox®

Ordering Information

Series

DEQ LC

Digital Equinox® load controller

Intended Use

Low voltage sensor used to provide ambient light level information to Digital Equinox® load controller or wallstations for indoor daylight harvesting applications.

Features

This speciality photosensor is factory calibrated to accommodate the relatively low light levels normally found on the ceiling in office applications. 360° lens allows the sensor to average the room light level, reducing the effect of reflective or lightly colored items brought into the room or placed on a desk.

Classification – Class 2 low voltage device.

Analog Photosensor

DEQ APS

Digital Equinox®

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

Ordering Information

Series

DEQ APS Digital Equinox® analog photosensor

Mounting

IN

Indoor

Options

CNPY

Canopy mount to a 4" square junction box.

1.15"

(2.9)

1.28"

(3.25)

Dimensions are shown in inches (millimeters) unless otherwise noted.

www.lithonia.com, keywords: DEQ LC and DEQ APS

PSG9

661

662

Low Voltage Momentary Switch

LVMS

WPM

Intended Use

Lithonia LVMS switches and WPM wallplates provide a durable and attractive solution for configuring low voltage control switch assemblies.

Switches snap-fit into the wallplates and are supplied with push-on connectors for low voltage

Ordering Information wire connections. Wallplates are offered in a variety of sizes and configurations and may be engraved with customer-supplied labels. Use with

Synergy® or SwitchPak® lighting control panels.

Classification – Class 2 low voltage device.

Series

LVMS

(blank) Standard switch

PILOT

Pilot light switch

KEY

Key operated switch

Options

FILLER

Snap-in blank filler

PILOT KEY

Key-operated switch with pilot

Color

IV

Ivory

WH

White

Ordering Information

NOTES:

1 Plates larger than four gangs may have longer lead times.

2 Must equal the number of gangs (one switch per gang) or two times the number of gangs (two switches per gang).

3 Two lines, seven characters per line for two switches per gang plate or two lines,

12 characters per line for one switch per gang plate.

Low Voltage Decora® Switch

LVDS

DSA FP

Series

WPM

Number of gangs

_G

1 to 10 1

Intended Use

Lithonia LVDS switches and DSA wallplates provide a durable and attractive low voltage switch solution with a standard strap-mount form factor and designer styling. Switches may be

Ordering Information

Number of openings

_MS

1 to 20 2

Finish

BS

Brushed stainless

WH

Painted white

IV

Painted ivory

Options

LE

Custom labeling

3 ganged with other Decora® style devices. DSA wallplates are offered in a variety of sizes and finishes. Use with Synergy® or SwitchPak® lighting control panels.

Classification – Class 2 low voltage device.

Series

LVDS

WH White

IV Ivory

Color

GY Gray 1

BK Black 1

AL Almond

1

Ordering Information

NOTES:

1 Additional delivery time and/or cost may be associated with these premium colors.

SSPL

SweepSwitch®

Series

DSA FP

Number of openings

D_

1 to 6 WH White

IV Ivory

Color

GY Gray

1

BK Black

1

AL Almond

1

BR Brown

1

Intended Use

Provides individual local line voltage override control of lighting in time-based control schemes. Can be used manually to turn lighting on and off in the normal manner. Resets itself automatically to the off position in response to a programmed power interruption signal provided by the lighting control panel.

Works like a standard wall switch for on/off operation. Automatically resets to off when power is removed for approximately five seconds. Switch

Ordering Information handle is lighted for easy location in the dark.

Wires to a 120V or 277V circuit switched by a

Synergy® or SwitchPak® relay panel like a standard toggle switch, is not line/load sensitive and does not require a neutral connection.

Strap-mount device; mounts in a standard single gang switch box and uses a standard toggle opening wallplate (not included).

Listings

UL Listed. CSA Certified.

Series

SSPL

Load amperage

05

0.1 to 5.0 amps

20

1.0 to 20 amps www.lithonia.com, keywords: LVMS, LVDS and SSPL

Voltage

277

120V or 277V (dual voltage)

PSG9

Intended Use

A unique lighting control system that integrates all aspects of lighting control into a single system platform. Combines architectural dimming, low voltage switching, lighting automation and energy management functions into a single scalable package capable of meeting the requirements of virtually any lighting control application.

Features

Combines the most popular aspects of lighting automation with full-featured low voltage switching and architectural dimming functions.

Switching and dimming functions may be controlled manually or scheduled on a weekly or calendar date basis. Functions may be set up using the integral LCD alphanumeric display and keypad or through the use of a personal computer with optional software (page 656).

Panels can operate individually as stand-alone lighting controllers or optionally in a network configuration with distributed intelligence. A choice of system controllers (page 665) allows customization to best meet the requirements and budget of each project.

Provides capacity for a maximum of 48 relays or

30 dimmers per enclosure (pages 666-669). Enclosures can operate in a master/secondary configuration, providing control of up to 96 outputs from a single controller. Relays and dimmers are each rated for control of one lighting circuit at the listed voltage.

Listings

UL Listed to US and Canadian safety standards.

California Title 24 certified.

Synergy® Lighting Control System

Synergy

®

Ordering Information

Series

SYES

Small enclosure,

2 modules max.

SYEM

Medium enclosure, 4 modules max.

SYEL

Large enclosure,

6 modules max.

SYESB

Small enclosure with breaker door, 2 modules max.

SYEMB

Medium enclosure with breaker door, 4 modules max.

SYELB

Large enclosure with breaker door, 6 modules max.

Output quantity/type

_DB1

Qty. 120V 2KW dimmers with six

20A circuit breakers, six dimmers per module

_DB2

Qty. 277V 3.5KW dimmers with four 20A circuit breakers, six dimmers per module

_DB3

Qty. 120V 1.5KW dimmers with six 15A circuit breakers, six dimmers per module

_DB4

Qty. 277V 3.3KW dimmers with four 15A circuit breakers, six dimmers per module

_R

Qty. single pole, 120/277 20A, eight relays per module

_RB1

Qty. single pole 20A relays, six

120V, 20A circuit breakers, eight relays per module

_RB2

Qty. single pole 20A relays, four

277V, 20A circuit breakers, eight relays per module

_RB3

Qty. single pole 20A relays, six

120V, 15A circuit breakers, eight relays per module

_RB4

Qty. single pole 20A relays, four

277V, 15A circuits, eight relays per module

_CB2

Qty. 277V constant breakers, four breakers per module

_CB1

Qty. 120V constant breakers, six breakers per module

_HB6

Qty. single pole 20A relays, four

347V, 20A circuit breakers, eight relays per module

_HB7

Qty. single pole 20A relays, four

347V, 15A circuit breakers, eight relays per module

_F

Qty. 0-10V dimmers with singlepole 20A relays, suitable for 120/

277V, eight relays and dimmers per module

_FH

Qty. 0-10V dimmers with singlepole 20A relays, suitable for 120/

277 and 347V, eight relays and dimmers per module

_FB1

Qty. 0-10V dimmers with single

20A relays, six 120V, 20A circuit breakers, eight relays and dimmers per module

_FB2

Qty. 0-10V dimmers, single pole

20A relays, four 277V, 20A circuit breakers, eight relays and dimmers per module

_FB3

Qty. 0-10V dimmers, single pole

20A relays, six 120V, 15A circuit breakers, eight relays and dimmers per module

_FB4

Qty. 0-10V dimmers, single pole

20A relays, four 277V, 15A circuit breakers, eight relays and dimmers per module

_FB6

Qty. 0-10V dimmers, single pole

20A relays, four 347V, 20A circuit breakers, eight relays and dimmers per module

_FB7

Qty. 0-10V dimmers, single pole

20A relays, four 347V, 20A circuit breakers, eight relays and dimmers per module

_ H

Qty. single pole 20A relays suitable for 120V, 277V or 347V operation, eight relays per module

Controller type

MLC

Basic controller for standalone panel operation

MLX

Enhanced controller for network panel operation

SCP

Secondary panel, less controller

Main feed options

(blank) No tap feed lugs, no main breaker

ML

Tap-feed lugs for powering up to four cabinets from a single main feed.

Requires 2 module positions; requires power modules with circuit breakers

MB_

Main breaker, 3 pole, specify

# of amps

NBAR

42 circuit neutral bar

Options

(blank) Panel ships as components consisting of enclosure, power modules and controller

FA

Panel ships fully assembled

(controller and relay modules factory-installed in enclosure)

DMX

Dimming interface required for connection to

DMX512 control

PHONE

Telephone interface 1

RO

Remote override, accepts contact closure to force all relays to full-

on for essential lighting applications 2

OS

Occupancy sensor compatible inputs for dry contact switches or occupancy sensors

3

LEGACY Allows control of legacy MiniPac®,

Sequel® and

MaxStar® dimmer cabinets

1

NOTES:

1 Not available with MLC controller.

2 Only required for _R and RB output types. All other modules come standard with RO option.

3 Only required for _R and _RB output types. All other modules come standard with OS option. RO option included when OS option specified.

Accessories

SYA SRE Recess kit for small enclosures

SYA MRE Recess kit for medium enclosures

(Order separately)

SYA LRE Recess kit for large enclosures

LSA DOC Job specific submittal and documentation

PSG9 www.lithonia.com, keyword: Synergy

663

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

664

System Enclosures

SYE

Intended Use

Provides housing and electrical support for the relay power modules, dimmer power modules and system controller in a Synergy® lighting control application.

Features

Synergy® system enclosures are shipped from factory stock in three sizes, accommodating either 2, 4 or 6 power modules (pages 666-668).

The enclosures are fabricated from cold rolled steel, are designed for surface wall mounting and carry a NEMA 1 electrical rating.

An optional recessed mounting kit permits the enclosure to be flush-mounted in a six-inch thick wall.

All enclosures are shipped with a factory installed power supply with input terminals provided for either 120, 240 or 277 volts supply voltage. Enclosures intended for use with dimmer modules are supplied with an internal thermostatically controlled cooling fan and a cover with hinged locking door to cover the power module mounted circuit breakers.

A variety of main lug, neutral bar and main breaker options (page 668) are available to configure

Synergy® as a bussed three phase or single phase dimming/switching panel.

Listings

UL Listed to US and Canadian safety standards.

Ordering Information

Series

SYE

Capacity

S

Small enclosure. 2 power module spaces. No circuit breaker door.

M

Medium enclosure. 4 power module spaces.

No circuit breaker door.

L

Large enclosure. 6 power module spaces. No circuit breaker door.

SB

Small enclosure. 2 power module spaces.

Provision for circuit breakers 1 .

MB

Medium enclosure. 4 power module spaces.

Provision for circuit breakers.

LB

Large enclosure. 6 power module spaces.

Provision for circuit breakers.

Voltage

120/277

120/240/277V, 50 or 60Hz operation

Shipping Weight:

Small enclosure

Medium enclosure

Large enclosure

30 lbs. (14 kg)

40 lbs. (18 kg)

50 lbs. (23 kg)

Dimensions are shown in inches (millimeters) unless otherwise noted. Add 1.5

(40) to height and width for recessed version.

NOTES:

1 Maximum one dimmer module.

Accessories (Order separately)

SYA SRE Recess kit for small enclosures

SYA MRE Recess kit for medium enclosures

SYA LRE Recess kit for large enclosures

SYPMB NBAR Neutral bar assembly. Requires one module space (page 668).

SYPMB MB_NBAR Main breaker assembly with neutral bar, 3-pole.

Specify capacity in amps (30, 40, 50, 60, 70, 80,

90, 100). Requires one module space (page 668).

48 (1,219) SYEL

34.5 (876) SYEM

21 (533) SYES

6"

(152)

20"

(508) www.lithonia.com, keyword: SYE

PSG9

Intended Use

Provides user interface, display, clock and logic circuits for a Synergy® lighting control system enclosure and a means to set up lighting control functions, including manual switching, manual and preset dimming, schedules, astronomic time control, photocell switching and daylighting.

Features

Constructed as a plug-in chassis to enhance initial installation and serviceability. Used to set up and save operational features of the system. Provides support for external control devices (Synergy® digital remote stations (page 658), Sequel® preset dimming control stations (page 657), Digital

Equinox® devices (page 659-660) and legacy dimmer cabinets (page 676) (optional).

User interface is designed for simple operation using the soft key format popular on automated teller machines. Large back-lit display provides text-based prompting and feedback for menu

Ordering Information navigation as well as status, diagnostic information and alarms.

Astronomic feature built into Synergy’s internal clock will calculate sunrise and sunset times for use in the lighting schedules. The controller also can read values from accessory photocells and provide automatic switching or dimming of lighting based on the ambient light level.

See the matrix below for additional features and capacities specific to the controller type selected.

Series

SYSC

NOTES:

1 No voice-prompted override with SYSC MLC.

2 Not available with SYSC MLC.

Controller type

MLC

Basic system controller

MLX

Network system controller

System Controllers

SYSC

Options

ISA

Three 16-bit ISA expansion slots

PHONE

Telephone interface for voice-prompted override and remote modem access (requires ISA option) 1

DMX

Theatrical dimming interface, required for connection to DMX512 control signal

LEGACY

Allows control of one complete network (255 dimmers) of legacy MiniPac®, Sequel® and Max-

Star® dimmer cabinets. Replaces master controller on existing systems.

Accessories (Order separately)

SYA SKIT

Permits two SYE enclosures to operate with a single controller.

SYSW CONFIG

Windows TM configuration software and cable

(page 656).

2

SYA CABLEA4

Class 2, four-conductor, plenum-rated network cable (page 670).

SYA CABLES2

Lithonia plenum-rated RS485 network cable 2

(page 670).

System Function

Relay Capacity

(No breakers)

Relay Capacity

(With breakers)

Dimmer Capacity

DMX512 Input

Scheduling

Analog Inputs

PC Support

Script Logic

Logging

Priority Logic

Ethernet Network

ARCNET Network

Telephone Override

BACnet®

RS232

Modem

Sequel® Stations

Legacy Dimmers

Digital Remotes

Features Selection Matrix

MLC Controller

48

40

30

MLX Controller

48 (96 total with secondary cabinet)

40 (80 total with secondary cabinet)

30 (60 total with secondary cabinet)

DMX channel-to-output DMX channel-to-output configured via hardware settings configured via controller software

11 schedules,

99 events

YES

100 schedules, unlimited events

YES

NO

NO

NO

NO

YES

NO

NO

NO

YES

YES, optional

YES

NO

YES

YES

YES

YES

YES

YES

YES

YES, optional

YES

YES

YES, optional

YES

YES, optional

YES

Functional

Soft Function

Keys

4-line 80-character LCD

Display with Backlight

System Status

LED Indicators

Navigation Keys

DB9 Serial

Port

Shipping Weight is 5.5 lbs. (2.5 kg).

www.lithonia.com, keyword: SYSC

PSG9

665

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

666

Relay Power Modules

SYPM 8R

SYPM 8H

Intended Use

Used in conjunction with system enclosure and controller (pages 664-665) to provide manual and automatic on/off control of all types of lighting loads. Combine with line voltage dimmer

(below), 0-10V and DALI (page 667) modules to create a complete lighting control solution for any application.

Features

Modules include eight 20A relays and are available for 120V to 277V and 120V to 347V applications. Unique zero-cross switching technology minimizes the destructive effects of switching large high-inrush loads, such as electronic fluorescent and HID. All relay module types may be ordered with optional 15A or 20A branch circuit breakers.

Modules are equipped with a pilot light output for each relay, eight low voltage contact switch inputs (see page 662 for available switches) and two analog inputs (see page 670 for photocells).

Switch inputs on units ordered with the "OS" option are compatible for direct connection to occupancy sensors (pages 672-673). All inputs are fully configurable through the use of a system controller (page 665) to work with a wide variety of input devices and control any combination of system relays and dimmers. Once configured, all module settings are stored locally and the module will continue to operate in fail-safe mode even if the system controller is removed from the system.

Listings

UL Listed to US and Canadian safety standards.

Ordering Information

Series Type

SYPM

SYPMB

Module for use with external circuit breakers

Module with circuit breakers

8R

Relay module with eight single-pole

20A relays for 120 or 277V operation

8H

Relay module with eight single-pole

20A relays for 120, 277 or 347V operation

NOTES:

1 Only available with SYPMB 8H module.

2 RO option is standard for all modules with OS option; RO and OS options are standard for 8H modules.

Shipping weight is 4lbs. (1.9kg) without breakers and 9lbs. (4.1kg) with breakers.

Circuit breakers/voltage

(blank) No circuit breakers

B1

Six 20A, 120V, 10KAIC breakers

B2

Four 20A, 277V, 14KAIC breakers

B3

Six 15A, 120V, 10KAIC breakers

B4

Four 15A, 277V, 14KAIC breakers

B6

Four 20A, 347V, 14KAIC breakers 1

B7

Four 15A, 347V, 14KAIC breakers 1

Options 2

RO

Remote override. Accepts contact closure to force all relays on in essential lighting applications

OS

Occupancy sensor. Eight low voltage inputs for contact switches or occupancy sensors.

Line Voltage Dimmer Power Module

SYPMB 6D

Intended Use

Used in conjunction with system enclosure and controller (pages 664-665) to provide manual and automatic on/off and line voltage dimming control of a wide variety of lighting loads. Combine with relay (above), 0-10V and DALI (page

667) modules to create a complete lighting control solution for any application.

Features

Modules include six 20A line voltage dimmers with integral 15A or 20A circuit breakers and are available for 120V, 230V and 277V applications.

Each dimmer is equipped with an air-gap relay and an architectural-grade toriodal filter.

All digital design ensures smooth, dependable

Ordering Information performance without field calibration. Unique combination of analog circuitry and digital signal processing techniques minimize the effects of poor power quality and prevent noticeable flicker and drift.

Individual dimmer response curves are field configurable to accommodate most lamp and ballast types via the system controller (page 665). Once configured, all module settings are stored locally and the module will continue to operate in fail-safe mode even if the system controller is removed from the system.

Listings

UL Listed to US and Canadian safety standards.

Series

SYPMB

Dimmers

6D

Six dimmers per module

Circuit breakers/voltage

B1

Six 20A, 120V, 10 KAIC breakers

B2

Four 20A, 277V, 14 KAIC breakers

B3

Six 15A, 120V, 10 KAIC breakers

B4

Four 15A, 277V, 14 KAIC breakers

B5

Four 20A, 120V, 65KAIC breakers

Shipping weight is 22lbs. (10kg).

www.lithonia.com, keywords: SYPM and SYPMB 6D

PSG9

Intended Use

Used in conjunction with system enclosure and controller (pages 664-665) to provide manual and automatic on/off and 0-10V dimming control of compatible four-wire fluorescent and non-dim loads. Combine with DALI (below), relay and line voltage dimmer (page 666) modules to create a complete lighting control solution for any application.

Features

Modules include eight 20A relays and 0-10VDC outputs for dimming ballast control, are available for 120V to 277V or 120V to 347V applications and may be ordered with optional 15A or

20A branch circuit breakers. Unique zero-cross switching technology minimizes the destructive effects of switching high-inrush loads. Each 0-

0-10V Fluorescent Dimmer Power Module

10V output may be used to control up to 50 compatible four-wire ballasts. Modules are equipped with two analog inputs (see page 670) for photocells) and eight low voltage inputs suitable for dry contact switches (page 662) and occupancy sensors (pages 672-673). All inputs are fully configurable through the use of a system controller

(page 665) to work with a wide variety of input devices and control any combination of system relays and dimmers. Once configured, all module settings are stored locally and the module will continue to operate in fail-safe mode even if the system controller is removed from the system.

Listings

UL Listed to US and Canadian safety standards.

SYPM 8F

Ordering Information

Series

SYPM

Module for use with external circuit breakers

SYPMB

Module with circuit breakers

Type

8F

Ballast module with eight single-pole, 20A relays and eight 0-10VDC analog outputs

(blank)

H

B1

Circuit breakers/voltage

No circuit breakers suitable for 120V or

277V operation

No circuit breakers suitable for 120, 277 or 347V operation

Six 20A, 120V, 10KAIC circuit breakers

B2

Four 20A, 277V, 14KAIC circuit breakers

B3

Six 15A, 120V, 10KAIC circuit breakers

B4

Four 15A, 277V, 14KAIC circuit breakers

B6

Four 20A, 347V, 14KAIC circuit breakers

B7

Four 15A, 347V, 14KAIC circuit breakers

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

Shipping weight is 4lbs. (1.9kg) without breakers and 9lbs. (4.1kg) with breakers.

Intended Use

Used in conjunction with system enclosure and

SYSC MLX controller (pages 664-665) to provide manual and automatic control of compatible devices on a DALI network. Combine with 0-10V

(above), relay and line voltage dimmer (page

666) modules to create a complete lighting control solution for any application.

Features

Module includes network controllers and power supplies for three DALI networks (loops) of up to

64 devices each. Connected DALI devices may be configured via the system controller (page 665) for status monitoring and prioritized control by any Synergy® user interface, timeclock schedule

Ordering Information or graphical workstation.

Listings

UL Listed to US and Canadian safety standards.

DALI Fluorescent Control Power Module

SYPM DALI

Series

SYPM DALI

Network controller and power supply for three DALI loops

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

Shipping weight is 4lbs. (1.8kg).

PSG9 www.lithonia.com, keywords: SYPM 8F and SYPM DALI

667

668

Neutral Bar and Main Breaker Modules

SYPMB NBAR

SYPMB MB_NBAR

Intended Use

Used in conjunction with system enclosure (page

664) and power modules equipped with branch circuit breakers (pages 666 and 667) to facilitate connection of an individual Synergy® cabinet to a three-phase, four-wire or single-phase, threewire main feed.

Features

Modules include a 42 circuit neutral bar rated for a #6 to 2/0 AWG main feed and #14 to #4

AWG branch neutral conductors. The neutral bar can be used in 120V, 277V or 347V applications.

The optional main breaker is available in capacities up to 100A and is rated for 120V/240V, 120/

208V and 277/480V feeds and conductor sizes up to 2/0 AWG.

Listings

UL Listed to US and Canadian safety standards.

Ordering Information

3 Phase, 4 Wire

Main Feed Conductors

2/0 AWG Maximum

SYPMB NBAR

18 Dimmer, 3 Phase, 4 Wire Example

Tap Feed Modules

SYPMB ML

SYPMB MB_ML

SYPMB MN

Series

SYPMB

Main breaker

(blank) No main breaker

MB_

Main breaker, 3 pole, indicate capacity:

30, 40, 50, 60, 70, 80, 90 or 100 amps

Neutral bar

NBAR

Neutral bar, 42 circuit

Intended Use

Used in conjunction with system enclosures

(page 664) and power modules equipped with branch circuit breakers (pages 666 and 667) to facilitate connection of up to four Synergy® cabinets to a single three-phase, four-wire or single-phase, three-wire main feed.

Features

ML modules include a three position power distribution block and optional main breaker. MN modules include a single position power distribution block and a 42 circuit neutral bar. All distribution positions include one main lug rated for a single #4 AWG to 500 kcmil conductor and four tap lugs rated for a single #14 to 2/0 AWG conductor each.

One ML module and one MN module is required for each application. All units are rated for 120V/

240V, 120/208V and 277/480V applications.

Listings

UL Listed to US and Canadian safety standards.

3 Phase, 4 Wire

Main Feed Conductors

500 kcmil

Maximum

SYPMB ML

SYPMB MN

Tap Feed Conductors

2/0 AWG

Maximum

SYPMB

NBAR

54 Dimmer, 3 Phase, 4 Wire Tap Feed Example

Shipping weights are 5 lbs. (2.3 kg) without main breaker and 8 lbs. (3.6 kg) with main breaker.

Ordering Information

Series

SYPMB

Main breaker

(blank) No main breaker

MB_

Main breaker, 3 pole, indicate capacity:

30, 40, 50, 60, 70, 80, 90 or 100 amps www.lithonia.com, keyword: SYPMB

Distribution lugs

ML

Phase conductor tap feed lugs, 3 position

MN

Neutral conductor tap feed lug with 42 circuit neutral bar

PSG9

Intended Use

Ideal for applications requiring circuit level remote control or lighting automation. Combines the powerful capabilities of the Synergy® lighting control system with the familiar footprint of a standard circuit breaker panel. This unique concept provides fully automated lighting control without the need to install both a relay panel and a branch circuit breaker panel. Also requires less wall space and will often provide a lower installed cost.

Features

Scheduling – Using integral astronomic clock capability, lighting can be fully automated to conform to a rotating seven-day schedule. Astronomic feature provides dusk/dawn operation, eliminating the need for photocells. Holiday schedule allows entry of up to 32 periods. Blinkwarn feature can blink lights automatically prior to a scheduled off.

Overrides – Use Synergy® digital remote stations

(page 658) to provide manual control of any combination of breakers and override scheduled events. Each station can provide up to nine buttons with integral LED status indicators. A single four-wire cable is all that is required for connection of up to 60 (16 with MLC controller) stations.

Optional switch input card also allows the use of traditional low voltage switches and other dry contact closures.

Networking – Panels can be networked together and used with other Synergy® switching and dimming panels to form a building-wide lighting control system. Networked systems offer the flexibility of central control, monitoring and programming via PC software. Integrates with building automation systems via native

BACnet TM protocol.

Capacity – Up to 42 circuits with 100, 225 or

400-amp bus. Controllable circuit breakers are available in 15, 20 or 30-amp single-pole or two-pole for 120/208-volt, 120/240-volt or

277/480-volt operation. Compatible with noncontrollable breakers.

Listings

UL Listed to US and Canadian safety standards.

Synergy® Controllable Breaker Panel

Synergy

®

Ordering Information

Series

SYBP18 18-pole capacity 1

SYBP30 30-pole capacity

1

SYBP42 42-pole capacity 1

Voltage

P1 120/208V

P2 277/480V

Maximum rating

100

100 amps

225

225 amps

400

400 amps

Main feed options

2

ML

Main lug

MB100

100A main breaker

MB225

225A main breaker

MB400

400A main breaker

NOTES:

1 Order branch circuit breakers separately. See selection table at below.

2 Consult factory for additional main breaker selections and interrupt ratings.

3 For house lighting control only.

4 Not available with MLC or SCP controllers.

5 Must provide panel schedules.

Main feed locations

T Top feed

B Bottom feed

Door type/mounting

SS Standard surface

DS Door-in-door surface

SF Standard flush

Controller type

MLC

Basic controller for stand-alone panel operation.

MLX

Enhanced controller for network panel operation.

SCP

Secondary panel, less controller

Options

DMX

Interface for connection to

DMX512 control

3,4

PHONE

Telephone interface 4

LVIN

Eight low voltage switch and two analog inputs

FA

Factory-assembled interior with breakers and controllers

5

LEGACY Interface to allow control of up to 62

MiniPac® distributed dimmer packs

Branch Circuit Breaker Selection Table

Controllable Breakers

(Order as separate items.)

SYBPB BABRS1020 120V, 20A, 1POLE

SYBPB BABRS1030 120V, 30A, 1POLE

SYBPB BABRS2020 120V, 20A, 2POLE

SYBPB BABRS2030 120V, 30A, 2POLE

SYBPB GHQRS1020 277V, 20A, 1POLE

SYBPB GHQRS1030 277V, 30A, 1POLE

SYBPB GHQRS2020 277V, 20A, 2POLE

SYBPB GHQRS2030 277V, 30A, 2POLE

NOTES: Contact factory for additional breaker sizes.

Standard Breakers (Non-Controllable)

SYBPB BAB1020

120V, 20A, 1POLE

SYBPB BAB1030

120V, 30A, 1POLE

SYBPB BAB2020

120V, 20A, 2POLE

SYBPB BAB2030

120V, 30A, 2POLE

SYBPB GHB1020

277V, 20A, 1POLE

SYBPB GHB1030

277V, 30A, 1POLE

SYBPB GHB2020

277V, 20A, 2POLE

SYBPB GHB2030

277V, 30A, 2POLE

Accessories (Order separately)

LSA DOC Job specific submittal and documentation.

SYSW CONFIG Windows

TM

95/98, 2000, NT or XP configuration software and cable (page 656).

________ Order branch circuit breakers separately. See

Branch Circuit Breaker Selection Table.

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

SYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEMSYNERGY® CONTROL SYSTEM

www.lithonia.com, keyword: Synergy

PSG9

669

670

Analog Photosensor

LSA APS

Intended Use

A low voltage system component that provides ambient light level information to a Synergy® or

SwitchPak® lighting control system for use in dimming, switching or daylighting applications.

Features

Units for outdoor or skylight applications mount to J-box via integral 1/2” nipple. Unit for indoor applications mounts directly to ceiling tile via peel-and-stick adhesive backing or mounts to Jbox using optional canopy. Units are factory-calibrated for the light levels indicted and connect directly to a Synergy® or SwitchPak® system analog input. Configuration, setpoints and deadband all are remotely configurable from the Synergy® or SwitchPak® controller keypad.

Classification – Class 2 low voltage device.

Ordering Information

Series

LSA APS

Type/mounting

OL

Outdoor (0-100 fc)

OH

Outdoor (0-1,000 fc)

S

Skylight/atrium (0-10,000 fc)

IN

Indoor (0-100 fc)

Options

CNPY

Canopy mount to a 4" square junction box

Network Cable

SYA

Intended Use

Plenum rated network cable suitable for use with industrial EIA RS-485 networks.

SYA CABLES2 – Fully compatible with Synergy®

MLX (page 665) and SwitchPak® System Remote

(SR option) (page 671) panel to panel networks.

SYA CABLEA4 -Fully compatible for use with

Synergy® SQCS (page 657) and SYRS (page

658) digital networks.

Features

Single twist pair network cables with conductor color coding consistent with all Lithonia factory wiring diagrams and installation instruction for trouble-free network installations.

SYA CABLES2 – For use with industrial EIA

RS-485 networks.

SYA CABLA4 – Includes all required power and communication conductors. For use with industrial EIA RS-485 networks plus two #16 AWG conductors for 24V station power.

Listings

UL Listed, NEC type CL2P, rated for 75° C/300 Volts.

Ordering Information

Series

SYA

Cable

CABLES2

CABLEA4

Length

1000FT

1000 feet

500FT

500 feet 1

250FT

250 feet

NOTES:

1 Additional delivery time may be associated.

www.lithonia.com, keywords: LSA APS and SYA

PSG9

Intended Use

A compact and economical lighting control panel that offers simplified solutions for a broad range of lighting control applications. This timebased controller switches lighting on/off at preset times while managing a variety of low voltage inputs. Relays are rated to directly switch 20A lighting loads, eliminating the need for external contactors or relays.

Features

Simple Set-Up and Operation – Programming is quick and easy using the large LCD display with associated soft keys and automatic ReadyHelp™ on-screen help guide. Unique quick-assign keys provide one-touch program selections and instant override.

Scheduling – Individual daily schedules automatically repeat for seven-day lighting load operations. Holiday schedule accommodates 32 dates. Astronomic and automatic Daylight Savings Time operation.

Lighting Control Panel for Switching Applications

Warn-before-off feature flashes lights prior to turning off.

Overrides – Eight low voltage switch inputs can be programmed to provide manual control of any combination of relays or override one to eight zones of scheduled lighting. Analog photocell input does not require remote calibrations.

System Remote Option – A single SwitchPak® provides a complete lighting control solution and can be used to control operation of additional units. This powerful option expands the capability of Switch-

Pak® to a system level without adding the complexity often associated with networked systems.

Housing – NEMA 1 enclosure wall-mount with hinged locking cover. Separate line and low voltage compartments

Capacity – Eight single-pole, 20A rated relays for

120/277 dual voltage. Optional configurations of

600V two-pole relays.

Listings

UL Listed to US and Canadian safety standards.

SPAK

Ordering Information

Series Relays/poles

SPAK 8S

Eight single-pole 20A relays

4S

Four single-pole 20A relays

4S2D

Four single-pole 20A relays and two double-pole 30A relays

4D

Four double-pole 30A relays

NOTES:

1 Specify SR option for all SwitchPak® panels to be linked together.

Voltage

120/277 120/277 dual voltage

Options

SR

System remote

1

Accessories (Order separately)

LSA APS

Analog photosensor (page 670)

SYA CABLES2

System remote network cable for plenum applications (page 670)

LVMS/WPM

Low voltage override switches (page 662)

LVDS/DSA

Decora® style low voltage override switches

(page 662)

Low Voltage Remote Station

LVRS

Intended Use

The LVRS low voltage remote station is ideal when one to nine buttons are required for a compact location. Buttons may be programmed at SwitchPak® panel for override control of individual or multiple relays.

Features

Stations are single gang, screwless appearance and are available with 1 to 9 buttons in a variety of painted and metallic finishes. Optional LED pilot lights provide positive feedback of button

Ordering Information operation. Button caps can be engraved with labels having up to two lines of text.

Installation: wallstation mounts in a grounded Lithonia #SYRS 1GR or Steel City #52C13 plaster ring. Stations connect to SwitchPak® panel switch inputs with #18 - #14 AWG low voltage

Class 2 conductors.

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

ANELANELANELANELANEL

Y PY PY PY PY P

AK® RELAAK® RELAAK® RELAAK® RELAAK® RELA

CHPCHPCHPCHPCHP

SWITSWITSWITSWITSWIT

Series Number of gangs Number of switches

LVRS 1G

1 gang

_SW

1 to 9

NOTES:

1 Other finishes available; contract your local Lithonia representative or the Lithonia factory for more information.

PSG9

Finish

1

BJ4

Brushed stainless steel, black buttons

WC2

Painted white, white buttons

IE3

Painted ivory, ivory buttons www.lithonia.com, keywords: SPAK and LVRS

Options

PL

24V pilot indicators

671

672

Directional Wall or Ceiling Mount Occupancy Sensors

LMT H

Intended Use

Provides automatic on/off lighting control for indoor applications where a directional occupancy sensor is required. Use with LPCS power pack

(page 674), Synergy® (pages 654-669) or Switch-

Pak® (page 671). Versions are available for a wide variety of coverage patterns for hallways, warehouses and rooms with pendant fixtures.

Features

Directional sensor heads are low voltage and mount quickly to a wall or ceiling using the supplied "twist and lock" bracket. High motion sen-

58

Field of View (in feet)

TOP VIEW

31

16

11.5

0

11.5

16

31

Ordering Information

Series

LMT H

Multi-technology directional sensor head

58

8

SIDE VIEW sitivity and automatically adapting digital circuitry provide "install and forget" simplicity. Integrated photocell may be used to hold lights off when sufficient daylight is available.

LMT – Multi-Technology Sensor Head. Ultrasonic and infrared sensing provide maximum sensitivity to small movements and high immunity to false triggering. 500ft 2 coverage for minor motion, 1200ft 2 coverage for major motion when mounted at an 8ft height.

Listings

UL Listed to US and Canadian safety standards.

LIRC

16.6

0

16.6

10

29

0

58

Field of View (in feet)

LIRC H

TOP VIEW

29

58

8

0

0 3 8 15 31

SIDE VIEW

68

Field of View (in feet)

LIRC LR H

TOP VIEW

SIDE VIEW

Intended Use

Provides automatic on/off lighting control for indoor applications where a directional occupancy sensor is required. Use with LPCS power pack

(page 674), Synergy® (pages 654-669) or Switch-

Pak® (page 671). Versions are available for a wide variety of coverage patterns for hallways, warehouses and rooms with pendant fixtures.

Features

Directional sensor heads are low voltage and mount quickly to a wall or ceiling using the supplied "twist and lock" bracket. High motion sensitivity and automatically adapting digital circuitry provide "install and forget" simplicity. Integrated photocell may be used to hold lights off when sufficient daylight is available.

LIRC H – Infrared Sensor Head. Passive infrared sensor head ideal for areas where it can be

Ordering Information mounted with an unobstructed view of the occupants. 850ft

2

coverage for minor motion,

2500ft 2 coverage for major motion when mounted at an 8ft height.

LIRC LR H – Infrared Hallway Sensor. Passive infrared sensor head ideal for long, relatively narrow areas, such as aisles, hallways and corridors. 100ft long x 14ft wide coverage pattern when mounted at a 10ft height.

LIRC HB H – Infrared High-Bay Sensor. Designed for long, narrow spaces where a high mounting height is required, such as warehouse aisles and factory storage racks, this passive infrared sensor head provides long range and high sensitivity.

55ft long x 7ft wide coverage pattern when mounted at a 30ft height.

Listings

UL Listed to US and Canadian safety standards.

Series

LIRC H

Infrared wide-view directional sensor head

LIRC LR H

Infrared hallway directional sensor head

LIRC HB H

Infrared high bay directional sensor head

3.5

0

3.5

30

Field of View (in feet)

LIRC HB H

TOP VIEW

SIDE VIEW

0

0 14 42 71 100

0

3 13 25 52 www.lithonia.com, keywords: LMT and LIRC

PSG9

Intended Use

Ceiling mount sensor heads provide automatic on/off lighting control for indoor applications where an occupancy sensor with a 360° coverage pattern is required. Use with an LPCS power pack

(page 674), Synergy® system (pages 654-669) or

SwitchPak™ relay panel (page 671). Multi-technology, ultrasonic and passive infrared sensors are available for a wide variety of applications.

Features

Omni-directional sensor heads are low voltage and mount quickly to a variety of ceiling surfaces using the supplied hardware. High motion sensitivity and advanced, automatically adapting dig-

Multi-Technology Sensor Head

Omni-directional Ceiling Mount Occupancy Sensors

ital circuitry provide "install and forget" simplicity. Integrated photocell may be used to hold lights off when sufficient daylight is available.

LMTO H – Ultrasonic and infrared sensing provide maximum sensitivity to small movements and high immunity to false triggering. Perfect for classrooms, large offices, conference rooms and cafeterias. 1000ft 2 coverage for minor motion,

2000ft 2 coverage for major motion when mounted at an 8ft height.

LUSO H – Ultrasonic sensors provide excellent sensitivity to small movements without the requirement of an unobstructed view of the occupants. Use for storage areas, warehouses, cafeterias and public areas in commercial facilities.

1000ft

2

coverage for minor motion, 2000ft

2

coverage for major motion when mounted at an 8ft height.

LIRO H – Passive infrared sensor with a high immunity to false triggering that works well in lobbies, closets, wide hallways and other areas with an unobstructed view of the sensor.

1500ft 2 coverage for major motion when mounted at an 8ft height.

Listings

UL Listed to US and Canadian safety standards.

20

16

11.5

TOP VIEW

LMTO H

0

Ordering Information Example: LMTO H

11.5

16

20

Series

LMTO H

Multi-technology ceiling-mounted sensor head

8

SIDE VIEW

32

20

22.5

15 11 9 5.5

3 0 3 5.5

9 11 15 20

22.5

32

LUSO H

Ultrasonic Sensor Head

Ordering Information: Example: LUSO H

16

11.5

0

11.5

16

Series

LUSO H

Ultrasonic ceiling-mounted sensor head

Infrared Sensor Head

LIRO H

Ordering Information:

LIRO H

Series

LIRO H

Infrared ceiling-mounted sensor head

TOP VIEW

20

10

0

10

20

SIDE VIEW

8

0

20 15 11 9 5.6

3 0 3 5.6

9 11 15 20

Minor Motion, IR Major Motion, IR Minor Motion, Ultrasonic Major Motion, Ultrasonic www.lithonia.com, keywords: LMTO, LUSO and LIRO

PSG9

673

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

LITRONIC® OCLITRONIC® OCLITRONIC® OCLITRONIC® OCLITRONIC® OC

ANCANCANCANCANC

CUPCUPCUPCUPCUP

Y SENSORSY SENSORSY SENSORSY SENSORSY SENSORS

Power Control Station

LPCS

Intended Use

Switches line voltage lighting loads and provides low voltage power to Litronic® occupancy sensor heads (pages 672-673) and Digital Equinox® stations (pages 659 & 660). The DCO option can be used to send a dry contact status signal to HVAC or building automation systems.

Features

Integrated 24VDC Class 2 supply and power relay provide a convienient and durable means for switching lighting loads when distributed relay control is desired. Power relay utilizes zerocross switching for extended life and is rated for fluorescent, incandescent, low voltage and motor loads. Integral 24V power supply is short-cicuit protected and compatible with all Litronic® occupancy sensors and Digital Equinox® stations.

Mounts with integral threaded nipple to ballast cavity or junction box knock out.

Listings

UL Listed to US and Canadian safety standards.

Ordering Information:

Series

LPCS

Voltage

MVOLT

120/240/277 VAC, 60Hz (relay rating: 20A fluorescent/ incandescent; 1HP, 120VAC; 2HP, 240VAC)

347

347 VAC, 60Hz(relay rating: 15A fluorescent; 1HP,

120VAC; 2HP 240VAC)

Options

DCO

Dry contact output for use in signalling other systems. Contacts rated for 0.5A, 120VAC, 30VDC.

674

Wall-Switch Replacement

LIRW

Decora®

Single Switch

Sensor

Dual Switch

Sensor

Intended Use

Designed to replace a standard wall switch and provide automatic lighting control in a variety of indoor applications requiring on/off and bi-level switching control. Sensors will always automatically turn off lights after no motion is detected for a period of time, but may be configured to operate in either “manual on” or “automatic on” modes.

Single Switch – Use for applications that require only a single zone of on/off

control, such as private offices, employee lounges and conference rooms. May be used in conjunction with a DSD or

ISD Series dimmer (pages 677-679) when continuous dimming control with automatic on/off operation is desired.

Dual Switch – Perfect for use with RT5™ fixtures with the step-dim option, this sensor provides dual switched outputs for high/low, inboard/outboard, or two zone control. Perfect for private of-

Ordering Information: fices, classrooms, conference rooms and day care centers. Photocell calibration and sensor timeout may be set to adjust automatically based on actual occupant usage.

Features

Advanced passive infrared occupancy sensor detects movement over 2000ft 2 with a 180° lineof-sight coverage pattern. One (LIRW) or two

(LIRW DS) front-mounted switches provide independent manual override control for occupants.

Integrated photocell may be used to hold lights off when sufficient daylight is available.

Low profile Decora® design matches DSD, ISD

(pages 677-679) and LVDS (page 662) Series devices and is compatible all with DSA Series faceplates (page 677).

Listings

UL Listed to US and Canadian safety standards.

Series

LIRW

Switch

(blank) Single switch

DS Dual switch

Voltage

MVOLT

www.lithonia.com, keywords: LPCS and LIRW

Color

WH

White

IV

Ivory

Primary relay rating:

Fluorescent: 1200VA 120V; 2700VA 277V

Incandescent: 800W 120V

Secondary relay rating:

Fluorescent: 800VA 120V; 1200VA 277V

Incandescent: 800W 120V

PSG9

Intended Use

Provides manual and preset dimming of most lamp types in wallbox applications. Offered in a variety of styles and architectural finishes. May be used singly, with matching remote stations or interfaced with external systems.

Features

Master raise and lower buttons adjust intensity of all lights dimmed from station. Channel raise and lower buttons adjust intensity level of individual channels. LED bar graph displays intensity level.

Select button saves presets. Fade time is adjustable for each preset scene. Preset button saves and activates presets. Off function turns off all lighting. Low-end and high-end dimming limits

Integrated Wallbox Dimming System

and dimmer curves are adjustable per channel.

Terminals on rear of station allow access from

SQRS remote stations or momentary dry contact closures to: six presets, master raise/lower, channel raise/lower, select and off.

Overall maximum is 2000VA. Maximum per output (1-4) is 600VA electronic ballast or 800VA incandescent, magnetic low voltage and magnetic ballast, 600VA electronic two- and threewire fluorescent ballasts. Mounts in five-gang masonry wall box.

Listings

UL Listed to US and Canadian safety standards.

SQIDC

Sequel® IDC

Ordering Information

Series

SQIDC

Capacity (VA)

2000

2000 watts

Number of presets and channels

6P 4C 6 presets, 4 channels

6P 8C 6 presets, 8 channels 1

Finish

BJ4

Brushed stainless steel, black buttons

WC2

Painted white, white buttons

IE3

Painted ivory, ivory buttons

BL4

Painted black, black buttons

2

BF4

Polished brass, black buttons

2

Wallplate style

SD

Solid

TR

Translucent

Voltage

120

DIMMINGDIMMINGDIMMINGDIMMINGDIMMING

NOTES:

1 8-channel unit requires Sequel® MiniPac® dimmer cabinet (page 676) for control of loads on channels 5-8.

2 Additional delivery time and/or cost may be associated.

Accessories (Order separately)

SQCS 5GB 5-gang backbox for 4C and 8C stations.

BKLE Engraved button caps. Specify wording.

Series Width Thickness Height

SQIDC 10-1/8 (257) 1/4 (6) 4-5/8 (117)

Dimensions are shown in inches (millimeters) unless otherwise noted.

Remote Stations

SQRS

Intended Use

Activates control functions in conjunction with the Sequel® IDC wallbox dimming system.

Features

Operation – Functions include preset recall, channel raise/lower, master raise/lower and off.

Installation – Mounts to a Lithonia SYRS 1GR box or 2" wide single-gang switch box.

Classification – Class 2 low voltage device.

Ordering Information

Series Number of buttons

SQRS 1S

1 button

2S

2 buttons

3S

3 buttons

4S

4 buttons

5S

5 buttons

6S

6 buttons

9S

9 buttons

NOTES:

1 Additional delivery time and/or cost may be associated.

PSG9

Finish

BJ4

Brushed stainless steel, black buttons

WC2

Painted white, white buttons

IE3

Painted ivory, ivory buttons

BL4

Painted black, black buttons 1

BF4

Polished brass, black buttons 1

Accessories (Order separately)

SYRS 1GR 1-gang plaster ring.

BKLE Engraved button caps. Specify wording.

www.lithonia.com, keywords: SQIDC and SQRS

Series Width Thickness Height Weight

SQRS 2-7/8 (73) 1/4 (6) 4-5/8 (117) 1/2 (.2)

Dimensions are shown in inches (millimeters) or pounds (kilograms) unless otherwise noted.

675

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

676

Remote High Power Dimmer Pack

SQMPDC

MiniPac®

Intended Use

Increases the individual channel capacity for

SQIDC wall box dimming system (page 675) or may be used as a remote dimmer pack for a

Synergy® system equipped with the Legacy option (page 665).

Features

When used with SQIDC: An integral switch matrix allows dimmers to be flexibly assigned to SQIDC station channels. Up to four dimmer pack may be used per SQIDC system.

When used with Synergy®: MLX controller with

Legacy option required; up to 64 dimmer packs may be connected to each controller. Dimmers are fully configurable from system controller and software and may be controlled by any Synergy® user interface or schedule.

High quality architectural-grade filters minimize lamp noise. Dimmers are cooled through natural convection flow provided by front cover venting and are available with or without positive air gap on/off relays.

Installation – NEMA 1 enclosure is suitable for surface or flush wall mounting. Dimmers are fed from individual 15A or 20A branch circuits. All dimmers in a single pack must be fed from a single phase; no phase relationship between different dimmer packs or SQIDC circuits. Connects to

Synergy® cabinet or SQIDC via Lithonia SYA CA-

BLES2 network wire (page 670).

Listings

UL Listed to US and Canadian safety standards.

Ordering Information

Series

SQMPDC

Number of dimmers

2 2 dimmers

4 4 dimmers

Remote Dimmer Modules

RDM

Dimmer type

UX

Universal incandesent; two wire fluorescent

UF

Universal incandesent; and two, three and four-wire fluorescent; non-dim

Capacity per dimmer

2

2000VA, 120V

4

4000VA, 277V

Type

S2

Intended Use

Used to boost the capacity of an ISD (page 678),

DSD (page 677), or SQIDC (page 675) Series wallbox dimmer. Also allows an ISD Series dimmer to control three-wire fluorescent dimming ballasts and SQIDC dimmers to control four-wire fluorescent dimming ballasts.

Features

Available for a wide variety of dimming load

Voltage

120 120V (single phase)

277 277V (single phase)

Options

EM For essential lighting loads. All dimmers automatically set to full on upon loss of normal power. Type

4UX2 or 4UX4 cabinets only. Transfer of input fee by others.

types. Models for use with line voltage loads include an integral RFI filter and may be surface or flush mounted using a 1900 box and 2-gang raised cover. All models are phase independent of the control device and equipped with a lowend trim adjustment.

Listings

UL Listed. CSA Certified. NOM Certified.

Ordering Information

Series

RDMI 2000 120 1920 W/VA, 120V, 50/60Hz for incandescent, magnetic low voltage, neon and cold-cathode.

RDMF 2000 120 1920 VA, 120V, 50/60Hz for Advance Mark 10™ and Lutron Hi-Lume®, Tu-Wire® and ECO10™ fluorescent

RDMI 3000 277 3000 VA, 277V, 50/60Hz for Advance Mark 10™ and Lutron Hi-Lume®, Tu-Wire® and ECO10™ fluorescent

RDMBC 120/277 1920VA at 120V, 4400VA at 277V, 50/60Hz for 0-10VDC fluorescent ballasts only. Mounts to a grounded 4" outlet box.

Load type Load voltage

Incandescent, magnetic low voltage, neon 120V

Advance Mark 10™, Lutron Tu-Wire®

Advance Mark 10™, Lutron Tu-Wire®

120V

277V

Lutron Hi-Lume®/ECO10™

Lutron Hi-Lume®/ECO10™

0-10VDC Fluorescent

120V

277V

Controller

SQIDC or ISD 600 I 120

SQIDC or ISD 600 I 120

RDM

RDMI 2000 120

SQIDC, ISD 600 ADEZ 120, RDMF 2000 120 or DSD 500 ADEZ 120 RDMF 3000 277

RDMF 2000 120

RDMF 3000 277

120V or 277V SQIDC or ISD 600 I 120 RDMBC 120/277 www.lithonia.com, keywords: SQMPDC and RDM

PSG9

Intended Use

DSD Series dimmers provide smooth full-range dimming of fluorescent fixtures equipped with the Advance Mark 10™ dimming ballast. Dimmers have a strap-mount design and may be used individually or ganged together for multiple load applications. These dimmers are ideally suited for use with Lithonia fixtures with the ADEZ dimming ballast option.

Features

Operation – Linear slide dimming with separate rocker switch for preset or three-way on/off operation and single location dimming.

Installation – All dimmers mount in standard single-gang switch box and can be ganged together using multi-gang wallplates (see below).

Compatability – Two-wire dimming ballasts as indicated on page 680.

Listings

UL Listed. CSA Certified. NOM Certified.

Architectural Wallbox Dimmers

DSD

Shown with DSA FP D1 wallplate.

Ordering Information

Series

DSD

Capacity (VA)

500

500 VA

Intended Use

Provides an architecturally-styled finish treatment for DSD, ISD, LVDS and LIRW Series products. Wallplates are available for individual devices and multi-gang applications with up to six devices.

Ordering Information

ADEZ

Ballast type

Advance Mark 10™ fluorescent

Voltage

120

277

Capacities and Derating

Color

IV

Ivory

1

WH

White

1

NOTES:

1 Includes standard Leviton Decora® wallplate. Order screwless or multi-gang

DSA wallplates separately below.

Advance Mark 10

TM

two-wire ballasts, 120V and 277V

4-1/2

(114)

1/4

(6)

2-11/16

(68)

1

(28)

2-5/8

(67)

Dimensions are shown in inches (millimeters) unless otherwise noted.

Advance

Mark 10™ catalog no.

VEZ-2Q26

VEZ-1T32

VEZ-1T42

VEZ-1Q18

VEZ-2Q18

VEZ-132

VEZ-2S32

VEZ-3S32

VEZ-154

VEZ-2S54

VEZ-1TTS40

VEZ-2TTS40

Lamp type

CFM26W

CFM32W

CFM42W

CFQ18W

CFQ18W

F32T8

F32T8

F3T8

F54T5/HO

F54T5/HO

FT40W

FT40W

Max. no. ballast/dimmer

One-gang or multi-gang

8

12

10

22

11

13

6

4

12

6

7

4

Advance

Mark 10™ catalog no.

REZ-1T32

REZ-1T42

REZ-1Q18

REZ-2Q18

REZ-2Q26

REZ-2T42

REZ-132

REZ-2S32

REZ-3S32

REZ-154

REZ-2S54

REZ-1TTS40

REZ-2TTS40

Lamp type

Max. no. ballast/dimmer

CFM32W

Onegang

13

Multigang

10

CFM42W 10 8

CFQ18W

CFQ18W

CFQ26W

CFTR42W

F32T8

F32T8

F32T8

F54T5/HO

F54T5/HO

FT40W

FT40W

23

11

8

5

13

6

4

7

3

12

6

18

9

6

4

11

5

3

6

3

9

4

For higher capacity, use either ISD ADEZ (page 678) or DSD with RDM remote dimmer (page 676).

Architectural Wallplates for Decora® Products

Features

Low profile wallplates are compatible with DSD,

ISD, LVDS and LIRW Series products and other

Decora® style devices.

Adapter strap permits mounting to the device without exposed fasteners

1

.

DSA FP

Series Openings 2

NOTES:

DSA FP

D1 One opening

D2 Two openings

D3 Three openings

D4 Four openings

1 Some color and opening combinations only are available with visible mounting screws.

2 One gang per opening is required.

3 Additional delivery time and/or cost may be associated with these premium colors.

D5 Five openings

D6 Six openings

PSG9

WH

White

IV

Ivory

AL

Almond 3

Color

GY

Gray

3

BK

Black 3

BR

Brown 3 www.lithonia.com, keywords: DSD and DSA FP

677

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS

DIMMINGDIMMINGDIMMINGDIMMINGDIMMING

678

Architectural Wallbox Dimmers

ISD

Intended Use

The ISD Series wallbox dimmers are designed to provide smooth full-range dimming for a variety of loads. Products are available for incandescent, low voltage, electronic low voltage and fluorescent two-wire and four-wire load types.

The ISD dimmers can be used in place of a standard wall switch to provide on/off and dimming lighting control.

Features

Fluid slide movement allows fine adjustment of light level over the entire dimming range. Separate on/off switch permits switching of lighting at a preset level. An integral LED indicator on illuminated dimmers turns on when the switch is off to facilitate switch location in a dark room.

Can be used with standard three-way or four-way switch for multi-location switching. ISD Series dimmers are compatible with Leviton Decora®

Series wallplates. Single location, linear slide dimming with separate push on/off switch for preset three-way and four-way switching. Available in standard white and ivory and supplied with a matching single-gang Decora® style wallplate. Snap-on Decora® style wallplate color change kits available (gray, black, brown, almond, white and ivory). Devices can be multi-gang mounted (optional multi-gang DSA wallplate required – see page 677).

Listings

UL Listed. CSA Certified. NOM Certified.

Ordering Information

3.28

(83.3)

2.12

(53.8)

4.15

(105.4 )

2.68

(68.1 )

1.41

(35.8 )

0.38

(9.7 )

Catalog number

Incandescent (supplied with white and ivory faceplates)

ISD 600 I 120 WH/IV

Illuminated slide dimmer; 600W,

120V, 60Hz

ISD 1000 I 120 WH/IV

Illuminated slide dimmer; 1000W,

120V, 60Hz

Magnetic low voltage (supplied with white and ivory faceplates)

ISD 600 LV 120 WH/IV

Illuminated slide dimmer; 600VA,

120V, 60Hz

ISD 1000 LV 120 WH/IV

Illuminated slide dimmer; 1000VA,

120V, 60Hz

Electronic low voltage (supplied with white and ivory faceplates)

ISD 400 ELV 120 WH/IV

Illuminated slide dimmer; 400VA,

120V, 60Hz

Fluorescent Mark 10™ (supplied with white and ivory faceplates)

ISD 600 ADEZ 120 WH/IV

Slide dimmer; 600VA, 120V, 60Hz

ISD 1000 ADEZ 120 WH/IV

Slide dimmer; 1000VA, 120V, 60Hz

ISD 1200 ADEZ 277 WH/IV

Slide dimmer; 1200VA, 277V, 60Hz

Fluorescent four-wire (supplied with white and ivory faceplates)

ISD BC 120/277 WH/IV

Ballast controller; 120/277V

Accessories (Order separately)

ISD CCKIT__ Color change kit, specify WH (White), IV (Ivory),

GY (Gray), BR (Brown), BK (Black) or AL (Almond).

DSA FP D__ Low profile thermoplastic wall-plate for ISD or

Leviton Decora ® compatible devices (page 677).

Maximum load/dimmer

Catalog Number

ISD 1000 I 120

ISD 600 I 120

ISD I/ISD LV/ISD ELV

One Two More than gang gang two gang

1000W 800W 700W

600W 500W 400W

ISD 1000 LV 120 1000VA 800VA 700VA

ISD 600 LV 120 600VA 500VA 400VA

ISD 400 ELV 120 400VA 350VA 250VA

Maximum number of ballasts/dimmer

120V Advance Mark 10™

ISD 600 ADEZ 120

Lamp

Catalog Number type

REZ-1T32

One gang

CFM32W 15

Two gang

13

More than two gang

10

REZ-1T42 CFM42W 12 10 8

REZ-1Q18

REZ-2Q18

REZ-2Q26

REZ-2T42

CFQ18W

CFQ18W

CFQ26W

CFTR42W

27

13

10

6

23

11

8

5

18

9

6

4

REZ-132

REZ-2S32

REZ-3S32

REZ-154

REZ-2S54

REZ-1TTS40

REZ-2TTS40

F32T8

F32T8

F32T8

F54T5/HO

F54T5/HO

FT40W

FT40W

5

9

4

16

8

14

7

4

7

3

13

6

12

6

3

6

3

11

5

9

4

ISD 1000 ADEZ 120

27

13

9

15

7

24

12

46

23

17

10

One Two More than gang gang two gang

26 20 18

20 16 14

37

18

13

8

32

16

12

7

22

11

7

12

6

19

9

19

9

6

11

5

17

8 www.lithonia.com, keyword: ISD

Maximum number of ballasts/dimmer

277V Advance Mark 10™

ISD 1200 ADEZ 277

Lamp

Catalog Number type

VEZ-2Q26

One gang

CFM26W 20

Two gang

20

More than two gang

20

VEZ-1T32 CFM32W 30 30 30

VEZ-1T42

VEZ-1Q18

CFM42W

CFQ18W

24

54

24

54

24

54

VEZ-2Q18

VEZ-2T42

VEZ-132

VEZ-2S32

VEZ-3S32

VEZ-154

VEZ-2S54

VEZ-1TTS40

VEZ-2TTS40

CFQ18W

CFTR42W

F32T8

F32T8

F32T8

F54T5/HO 18

F54T5/HO

FT40W

FT40W

27

12

33

16

11

9

28

14

27

12

33

16

11

18

9

28

14

27

12

33

16

11

18

9

28

14

PSG9

Intended Use

Connects directly to up to 80 compatible fourwire dimming ballasts with Class 2 low voltage control wire. Photocell automatically maintains a constant preset lighting level.

Features

Operation – Automatically maintains a constant preset lighting level in response to the availability of natural daylight (daylighting) and/or automatically maintains a constant preset light level over the life of the lighting system (lumen depreciation maintenance). 7-140 footcandles response range ± 1% at 70°F. Immediate or extended fade time response to light level changes.

Dimming Photosensor for Four-Wire Ballasts

Housing – Low-profile, UV-stable, white ABS housing with flat Fresnel lens.

Installation – Mounts directly to the ceiling tile.

Class 2 low voltage control wire.

Compatability – Four-wire dimming ballasts as indicated on page 680.

Classification – Class 2 low voltage device.

ISD DPC

DIMMINGDIMMINGDIMMINGDIMMINGDIMMING

Ordering Information

Series

ISD DPC

Dimming photocell

Applications:

Install near fixtures being controlled or central to circuit being controlled. Cone of response of photocell (60°) must contain area that is lit by fixtures being controlled.

Cone of response area must not contain any artificial uplight (i.e., desk lamp).

For day light harvesting, photocell should be installed six to eight feet from window line, depending on ceiling height, so that cone of response only contains work area inside actual window line. Can be used with an ISD BC ballast controller for automatic and manual dimming control.

1.15"

1.28"

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS www.lithonia.com, keyword: ISD DPC

PSG9

679

680

Fluorescent Dimming Guide

Ballasts have Class 2 control wires (purple and gray) to connect low voltage control devices such as Equinox® dimming control products.

Advantages:

• Control zones are created by interconnecting the low voltage wires and are not affected by the line voltage circuiting of the fixtures.

• Simple low voltage control devices such as the

ISD DPC dimming photocell are self-powered by the ballast.

• Small control devices can control a large number of ballasts since they are not supplying power to the loads.

• Choice of ballast suppliers.

• Lowest cost for 1% dimming.

Disadvantages:

• Requires additional controls.

(Example: Advance Mark 10®)

Ballasts have only one hot and one neutral wire and are directly controllable by fluorescent wallbox dimmers or universal system dimmers.

Advantages:

• Requires no additional wires, the black and white input leads provide for power and dimming.

• Wide dimming range (100-1%).

• Lowest installed cost.

Disadvantages:

• Minimum input voltage must be assured, requires dimmers with low-end trim adjustments or factory preset low-end adjustment.

(Example: Lutron Hi-Lume)

Ballasts are powered by a non-dimmed line voltage input and controlled via a second variable line voltage input.

Advantages:

• Line voltage control wiring

• Wide dimming range (100-1%).

Disadvantages:

• Requires a 2nd input power wire connection.

• Minimum input voltage must be assured, requires dimmers with low-end trim adjustments.

• Dimmers require a neutral.

• Highest relative cost to achieve 1% dimming.

*Four-wire digital addressable ballast (consult factory).

F13 Quad Tube

F18 Quad Tube

F26 Quad Tube

F32 Quad Tube

F13 Triple Tube

F18 Triple Tube

F26 Triple Tube

F32 Triple Tube

F42 Triple Tube

F57 Triple Tube

F70 Triple Tube

F36 Biax T5

F39 Biax T5

F40 Biax T5

F50 Biax T5

F55 Biax T5

F14 T5

F21 T5

F28 T5

F35 T5

F24 T5 HO

F39 T5 HO

F54 T5 HO

F17 T8

F25 T8

F32 T8

F40 T8

Control type

Ballast nomenclature

Lithonia nomenclature

--

--

--

1,2

1,2,3,4

1,2

1

--

--

--

1,2,3,4

1,2,3,4

--

1

1

2

--

1,2

1,2

1,2

1,2

1,2

1,2

Advance

Mark 7®

Four-wire

RZT/VZT,IZT

ADZT,ADZTH

Lutron

TVE

Universal

SuperDim®/

Ballastar®

Osram/

Sylvania Advance Lutron

Helios™ Mark 10®

Two-wire

Tu-Wire

Two-wire

Four-wire line voltage line voltage Four-wire Four-wire

TVE DIM-D,DIM-10,V5 (PHO-)DIM REZ/VEZ

TVE10 TUBV,TUDA, TUDD OS5C,OSDIM,OS10C ADEZ

2W

2W5

Lutron

ECO-10

Three-wire

line voltage

ECO

ECO10

Lutron

Hi-Lume/

Compact SE

Three-wire

line voltage

FDB/HL3

DMHL

The number of lamps that can be operated by each ballast is indicated below. Refer to ballast manufacturer for dimming range for each lamp type.

1,2 -1,2 ------

1,2 -1,2 -1,2 2 -1,2

1,2

--

--

--

1,2

--

--

--

1,2

--

1,2

--

--

--

1,2

--

--

--

--

--

--

--

--

--

--

--

--

--

1

1

1

--

--

--

--

1,2

--

--

--

--

--

--

--

--

--

--

--

1,2

1,2

1

1

1

1

1,2

--

1,2

--

2

1,2

1,2

--

--

--

--

--

--

--

--

--

--

--

--

--

--

1,2,3

1,2,3

--

--

--

1,2,3

1,2,3

--

1,2

1,2

1,2

1,2

--

--

--

--

1

--

--

--

--

--

1

1,2,3

--

1

--

--

1

1,2,4

--

--

1,2

1,2

1,2

1,2,4

1,2,3,4

--

--

--

--

--

--

--

--

--

1,2

1

1

1,2,3,4

--

--

--

--

--

1,2

--

--

--

1,2

--

1,2,3

1,2,3

--

Architectural dimming systems

--

--

--

--

2

1,2

1,2

--

--

--

--

--

--

--

1,2

1,2

1,2

1,2,3

1,2

--

1,2

1,2

1,2

1,2

1,2,3

--

--

1,2

1,2

1,2

1,2,3

1,2

--

--

--

--

1,2,3

1,2,3

1,2

Synergy dimmer modules

(pg 666-667)

Digital Equinox®

3

(pg 659-661)

MiniPac types (pg 676)

SQIDC (pg 675)

ISD Series (pg 678-679)

DSD Series (pg 677)

RDM (pg 676)

SYPM 8F SYPM 8F SYPM 8F SYPM 8F

SYRS EXT,DEQ LC SYRS EXT,DEQ LC SYRS EXT,DEQ LC SYRS EXT,DEQ LC

UF UF requires RDMBC requires RDMBC

ISD BC

N/A

RDMBC

ISD BC

N/A

RDMBC

UF UF requires RDMBC requires RDMBC

ISD BC

N/A

RDMBC

SYPMB 6DB

N/A

UX,UF

Yes

SYPMB 6DB

N/A

N/A

Wallbox dimmers

ISD BC ISD ADEZ ISD ADEZ

DSD ADEZ DSD ADEZ

Remote dimmer modules

RDMBC RDMF

UX,UF

Yes

RDMF

SYPMB 6DB

N/A

UF

Yes

ISD I with RDMF

N/A

RDMF

SYPMB 6DB

N/A

UF

Yes

ISD I with RDMF

N/A

RDMF

DALI

(various manufacturers)

Digital,

DALI protocol varies

ADALI,OSDALI,TRDALI 4

SYPM DALI

N/A

N/A

N/A

--

1,2

1,2

--

1,2

1

1

1.2

--

1,2

1,2

1,2

1,2

1,2

1,2

1,2

1,2

1,2

--

1,2

--

--

1,2

1,2,3

1,2,3,4

1,2,3,4

--

N/A

N/A

N/A

1 Lamp and ballast information shown on this table was compiled per ballast manufacturer literature available when the table was prepared. Refer to the ballast manufacturers’ current literature for up-to-date information about their product lines.

2 Refer to the ballast manufacturers’ information for specific low-end dimming for each lamp type.

3 Requires LPCS power control station (page 674).

4 Consult factory for specific lamp configurations available for different DALI ballast options.

www.lithonia.com

PSG9

Fluorescent Wiring Guide

TYPICAL WIRING DIAGRAMS

FOR FLUORESCENT WALLBOX DIMMERS

ISD ADEZ OR

DSD ADEZ

DIMMER

TWO-WIRE DIMMING BALLASTS (ADVANCE MARK 10®, LUTRON TU-WIRE)

120V OR 277V

3 WAY

SWITCH

ISD ADEZ OR

DSD ADE Z

DIMMER

CAP

OFF

RED BLACK

RED

HOT

GREEN

LINE

VOLTAGE

NEUTRAL

TWO-WIRE LINE VOLTAGE DIMMING BALLAST EXAMPLE

FOR SINGLE LOCATION CONTROL

FLUORESCENT

FIXTURES WITH

TWO-WIRE

DIMMING BALLASTS

HOT

NEUTRAL

LINE

VOLTAGE

GREEN

RED

RED

BLACK

GREEN

FLUORESCENT

FIXTURES WITH

TWO-WIRE

DIMMING BALLASTS

TWO-WIRE LINE VOLTAGE DIMMING BALLAST EXAMPLE

FOR TWO LOCATION CONTROL

HOT

NEUTRAL

CAP

OFF

LINE

VOLTAGE

RED

RED

ISD BC

DIMMER

FOUR-WIRE DIMMING BALLASTS (ADVANCE MARK 7®, SYLVANIA HELIOS™)

120V OR 277V

CLASS 2

CONDUCTORS

3 WAY

SWITCH

ISD BC

DIMMER

PURPLE

GRAY

BLACK

FLUORESCENT

FIXTURES WITH

FOUR-WIRE

DIMMING BALLASTS

RED

RED

GREEN

HOT

LINE

VOLTAGE

NEUTRAL

GREEN

FOUR-WIRE O-10V DIMMING BALLAST EXAMPLE

FOR SINGLE LOCATION CONTROL

PURPLE

GRAY

BLACK

GREEN

FOUR-WIRE 0-10V DIMMING BALLAST EXAMPLE

FOR TWO LOCATION CONTROL

CLASS 2

CONDUCTORS

FLUORESCENT

FIXTURES WITH

FOUR-WIRE

DIMMING BALLASTS

THREE-WIRE DIMMING BALLASTS (LUTRON HILUME, ECO-10)

RDM MAY ALTERNATELY BE POWERED BY A SEPARATE 120V CIRCUIT

ISD 600 I 120

DIMMER

CAP

OFF

RED

RED

BLACK

HOT

GREEN

LINE

VOLTAGE

NEUTRAL

120V THREE-WIRE LINE VOLTAGE DIMMING BALLAST EXAMPLE

FOR SINGLE LOCATION CONTROL

RDMF 2000 120

REMOTE

DIMMER

MODULE

SWITCHED HOT

LOAD

WHITE

FLUORESCENT

FIXTURES WITH

THREE-WIRE

DIMMING BALLASTS

NEUTRAL

277V HOT

277V LINE VOLTAGE

TO POWER FIXTURES

ISD 600 I 120

DIMMER

RDMF 3000 277

REMOTE

DIMMER

MODULE

LOAD

SWITCHED HOT

CAP

OFF

RED BLACK

120V HOT

NEUTRAL

120V LINE VOLTAGE

FOR CONTROL SIGNAL

RED

GREEN

277V THREE-WIRE LINE VOLTAGE DIMMING BALLAST EXAMPLE

FOR SINGLE LOCATION CONTROL

ORANGE

BLACK

FLUORESCENT

FIXTURES WITH

THREE-WIRE

UORESCENT DIMMINGUORESCENT DIMMINGUORESCENT DIMMINGUORESCENT DIMMINGUORESCENT DIMMING

FLFLFLFLFL

LITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMSLITHONIA CONTROL SYSTEMS www.lithonia.com

PSG9

681

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement