SAZ-1000D,1500D,2000D,3500D manual

SAZ-1000D,1500D,2000D,3500D manual
OUINER"S MANUAL
SAZ-1000D
SAZ-1500D
SAZ-2000D
SAZ-3500D
Congratulations on your purchase of a Sundown Audio high performance car audio
amplifier. Your new amplifier has been built to the highest standards of quality and
is intended to serve you for years to come.
Visit us online at http://www.sundownaudio.com
WARRANTY:
Your new Sundown Audio amplifier is covered by a 2 year limited warranty if
purchased from an authorized Sundown Audio dealer. This warranty does not
cover improper installation, accidental damage, misuse, abuse, improper
wiring, operation of unit outside of listed specifications, or any product that
has been modified or repaired by anyone other than Sundown Audio. This
warranty is transferrable provided the original invoice or receipt is still
with the unit so that its new owner can prove date and place of purchase.
All warranty returns must be sent freight prepaid to Sundown Audio and be
accompanied by the original sales invoice or receipt. For faster warranty
service please contact us at sundownz@sundownaudio.com to request a
return authorization code. At the sole discretion of Sundown Audio your
amplifier will be either repaired or replaced.
If no defect is found and the unit must be shipped back the customer is
responsible for return freight, if the unit is truly defective the replaced or
repaired unit will be shipped back prepaid. In the event of shipping damage
due to improper packaging of the return the customer is liable for the cost
of all damages, necessary repairs, or replacement. Be sure to properly pack
your return!
Sundown Audio also offers a 5 year guarantee to our customers for a
discounted replacement unit. We are so certain of the quality of our equipment
that even if you are at fault for causing damage to your amplifier we will offer
you a new unit at a reduced cost compared to MSRP. Contact us via e-mail to
take advantage of this offer, even though we doubt you will ever need to!
This offer applies ONLY to the original purchaser of the unit and is not
transferrable like the 2 year limited warranty. As is the case with standard
warranty claims the return MUST be sent prepaid and with a copy of the
original invoice or receipt.
RETURN ADDRESS:
Sundown Audio
ATTN: WARRANTY SERVICE
151 Rebel Hill DR.
Mooresville NC, 28115
_9-
Features
SAZ-1000D
HE Digital Class-D Linkable Mono Block Amplifier
HB Double Sided Through Hole Epoxy PCB
E 1 Ohm Stability
E Daisy-Chain Through Output RCA
E Efficiency : 85% @ 4 ohm, at 100Hz
E 24dB/0ct Variable Crossover
HE Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
E RCA Line Input and Master Output
E 24dB Octave Crossover Slope
E 24dB3B Octave Variable Subsonic Crossover Slope
E Variable Bass Boost
E Variable Low Pass Filter
E Variable Phase Shift
BH Four(d) Gauge Power Supply Connectors
HB Tested Voltage & THD : 14.4V & Less than 1% THD
E Operating Voltage : DC 10V-16V
E Wired Remote Controller
SAC-1500D
E Digital Class-D Linkable Mono Block Amplifier
E Double Sided Through Hole Epoxy PCB
E 1 Ohm Stability
E Daisy-Chain Through Output RCA
E Efficiency : 858% QQ 4 ohm, at 100Hz
EH 24dB/0Oct Variable Crossover
EH Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
E RCA Line Input and Master Output
E 24dB Octave Crossover Slope
E 24dB Octave Variable Subsonic Crossover Slope
E Variable Bass Boost
E Variable Low Pass Filter
E Variable Phase Shift
E Zero(0O) Gauge Power Supply Connectors
HE Tested Voltage & THD : 14.4V & Less than 1% THD
E Operating Voltage : DC 10V-18V
E Wired Remote Controller
Features
SAZ-2000D
E Digital Class-D Linkable Mono Block Amplifier
E Double Sided Through Hole Epoxy PCB
E 1 Ohm Stability
E Daisy-Chain Through Output RCA
E Efficiency : SE% @ 4 ohm, at 100Hz
EH 24dB/0Oct Variable Crossover
EH Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
E RCA Line Input and Master Output
E 24dB Octave Crossover Slope
EH 24dB Octave Variable Subsonic Crossover Slope
E Variable Bass Boost
E Variable Low Pass Filter
E Variable Phase Shift
E Zero(D) Gauge Power Supply Connectors
Bm Tested Voltage & THD : 14.4V & Less than 1% THD
E Operating Voltage : DC 10V~18V
E Wired Remote Controller
SAZ-3500D
E Digital Class-D Linkable Mono Block Amplifier
HE Double Sided Through Hole Epoxy PCB
E 1 Ohm Stability
E Daisy-Chain Through Output RCA
E Efficiency : SE% @ 4 ohm, at 100Hz
EH 24dB/0Oct Variable Crossover
HB Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
E RCA Line Input and Master Output
E 24dB Octave Crossover Slope
E 24dB Octave Variable Subsonic Crossover Slope
E Variable Bass Boost
E Variable Low Pass Filter
E Variable Phase Shift
E Zero(0O) Gauge Power Supply Connectors
вн Tested Voltage & THD : 14.4V & Less than 1% THD
E Operating Voltage : DC 10V-18V
E Wired Remote Controller
Specifications
SAZ-1000D
Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono
-RMS power, 2 ohm mono
-RMS power, 4 ohm mono
Signal to Noise Ratio
Low pass frequency crossover
Subsonic filter
Bass boost 0 45Hz
Phase shift control
Frequency response
T.H.D @ 4 ohm
Efficiency @ 4 ohm
Fuse rating
Input Sensitivity
Dimensions
SAC-1500D
Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono
-RMS power, 2 ohm mono
- RMS power, 4 ohm mono
Signal to Noise Ratio
Low pass frequency crossover
Subsonic filter
Bass boost @ 45Hz
Phase shift control
Frequency response
T.H.D @ 4 ohm
Efficiency @ 4 ohm
Fuse rating
Input Sensitivity
Dimensions
1800W x 1CH
1000W x 1CH
600W x 1CH
300W x 1CH
>90dB
35Hz-300Hz
1 OHz-6OHz
0-6dB
0~180 degree
10Hz~350Hz (+/- 1dB)
<0.1%
86%
30A x 3
200mV to 6V (+/- 5%)
252(W) x 58(H) x 294(L)mm
3000W x 1CH
1500W x 1CH
800W x 1CH
400W x 1CH
>90dB
35Hz-300Hz
10Hz~60Hz
O-edB
00-180 degree
1 0Hz-350Hz (+/- 1dB)
<O. 1%
86%
40A x 4
200mV to GV (+/- 5%)
252(W) x 58(H) x 434(L)mm
Specifications
SAZ-2000D
Rated power output
- RMS power, 2 ohm linkable/dual mono ------
- RMS power, 1 ohm mono
- RMS power, 2 ohm mono
-RMS power, 4 ohm mono
Signal to Noise Ratio
Low pass frequency crossover
Subsonic filter
Bass boost 0 45Hz
Phase shift control
Frequency response
T.H.D @ 4 ohm
Efficiency @ 4 ohm
Fuse rating
Input Sensitivity
Dimensions
SAZ-3500D
Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono
-RMS power, 2 ohm mono
-RMS power, 4 ohm mono
Signal to Noise Ratio
Low pass frequency crossover
Subsonic filter
Bass boost Q 45Hz
Phase shift control
Frequency response
T.H.D @ 4 ohm
Efficiency @ 4 ohm
Fuse rating
Input Sensitivity
Dimensions
4000W x 1CH
2000W x 1CH
1000W x 1CH
500W x 1CH
>90dB
35Hz-300Hz
10Hz~60Hz=
0-6dB
0~180 degree
10Hz~350Hz (+/- 1dB)
<0.1%
86%
200A (external type fuse)
200mV to GV (+/- 5%)
252(W) x 53H) x 494(L)mm
7000W x 1CH
3500W x 1CH
1750W x 1CH
750W x 1CH
>90dB
35Hz-300Hz
10Hz-G6OHz
0-6dB
0~180 degree
1 0Hz-350Hz (+/- 1dB)
<0.1%
86%
S50A (external type fuse)
200mV to 6V (+/- 5%)
252(W) x 53H) x 660(L)mm
RCA Connection
SAZ-1000D / SAZ-1500D / SAZ-2000D / SAZ-3500D
Single Amp Input Connection
LU GAIN © LPF BASS BOOST PHASE
mm || -06 à @ O la la O y
= 90 =
CLASS O LIMHAEBSLE MONO 8LOCH AMPLIFIER
@ == = |
HEAD UNIT
Wired Remote Controller
Dual Amp Input Connection (MASTER & SLAVE RCA Connection)
"MASTER UNIT"
<B> to SLAVE UNIT "BR IN"
R OUT GAIN SUBSONIC LPF BASS BOOST PHASE
=] 0: © [© © elo of ha
= © © LE Донн
CLASS O LiIAHASLE MOMO SLOC+H+ AMPLIFIEA
* BR OUT (BRIDGEABLE OUTPUT)
LC 247) ses | * BRIN (BRIDGEABLE INPUT)
С
HEAD UNIT
"SLAVE UNIT"
Wired Remote Controller
LUS GAIN SUBSONIC LPF BASS BOOST PHASE
00 à @ à Em?
=
CLASS O0 LINHASLE MONO SLOCH AMPLIFIER
Power Connection
SAZ-1000D SAZ-1500D
pa POWER O FSE A
EEE
WE Cer
To +12V DC
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
to REMOTE Turn-on
from HEAD UNIT
vo ® ©
| CAR STEREO HEAD UNIT | BATTERY | CAR STEREO HEAD UNIT BATTERY
SAZ-2000D / SAC-3500D
GNDL REM BE
MIE © © © @]
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line ©
fuse holder from
the © terminal of battery.
© =
IL IL E ===
To +12V DC
GROUND
Ls
® ©
to REMOTE Turn-on
from HEAD UNIT
A\ Caution BATTERY
This amplifier is not supplied with internal fuse in itself.
| CAR STEREO HEAD UNIT Make sure you install in-line fuse holder from the + terminal of battery.
Recommend 200 Ampere fuse.(SAZ-2000D)
Recommend 350 Ampere fuse.(SAZ-3500D)
+12V Power
Connect the +12V terminal of the amplifier to the + terminal of the battery
using a large gauge power wire (preferably 1/0 gauge). lt is critical to utilize
an in-line fuse within 8 inches of the battery to ensure safe operation of the
amplifier. Make sure that the fuse is not installed while you are connecting
the + wire to the battery terminal to avoid sparking and possible injury or
amage.
SROUND
Disconnect the battery and connect the GND (ground) terminal to the cars
chassis. Keep this cable as short as possible (not longer than 10 inches).
Be certain that the chassis ground point is free of rust, paint, and grime
to ensure a solid electrical connection.
REMOTE
Connect the REM terminal to either the remote output lead from the radio
or another switched 12V supply such as the power antenna wire.
A Caution
First make the ground connection, then +12V wire connection and finally
the remote connection. Furthermore, the +12V wire must always be fused
at the battery for protection against possible damage. If you need to replace
the power fuse, replace it with a fuse of the same value. lt may result in
a serious hazard to use a fuse of a different type or rating.
_8-
Single Amp Speaker Connection
SAZ-1000D
ohms
©
| | 1-4
BR | ohms
A...
Di
SAZ-1500D / SAZ-2000D 7 SAZ-3500D
1-4
ohms
2-8
ohms
2-8
ohms
Dual Amp Speaker Connection
SAZ-1000D
"MASTER UNIT"
i
а E |
FH
Е i
= i
= i
= i
Е y
емо QL:
+ 22° i 1
Sama aEE EEE EEE 00 Ctessssssssssssssssssssss? mm eee de eee a 7
ual > .
“ou n'éuuuuunt
Use 8 Gauge(AWG) wire cable 7 | 2-8
| ohms
a“ CTS
ih
1 q
e
le!
©
=
=]
B=
E [9];
© |®
Не
еде" 22
auf
ou qu
"линии" ФннЙ ини?
SAC-1500D / SAc-c000D / SAc-3500D
"MASTER UNIT"
END of REM On a+ 5
Use 8 Gauge(AWG) wire cable _—— Y 1 2~8
ohms
|
Panna’ CM
Using a dual amplifier configuration, the MASTER amplifier has total control
over the SLAVE amplifier. When using dual amplifier to operate subwoofer,
the positive terminal of the subwoofer's voice coil must be connected to
the positive terminal of the MASTER Amplifier and the negative terminal of
the subwoofer's voice coil must be connected to positive terminal of
the SLAVE Amplifier. Be advised that the dual amplifier configuration has
tremendous output potential, so ensure that your subwoofers can handle
such a large amount of power.
| Caution
When utilizing the dual amplifier configuration it is important
to note that the connected speaker load can be no lower
than 2 ohms. Connecting a lower impedance load can damage
the amplifier and void your warranty
-10-
Trouble Shooting
This power amplifier has protection features to prevent any damages from misuse or faulty
conditions. If the unit senses excessive heat, short circuited speakers or overload, the
protection indicators will light, and the system will be turned off. In order to check the
occurred problem, you should turn all levels down and all power off and carefully check the
installation for wiring mistakes or short. If the amplifier shuts down due to excessive heat,
the protection indicators will not light : simply allow time for the unit to cool.
Before removing your amplifier, refer to the list below and follow the suggested procedures.
Always test the speakers and their wires first.
AMPLIFIER IS NOT POWERED UP
€ Check that there is battery power on the +12V terminal.
€ Check that remote terminal has at least 13.8V DC remote connection.
+ Check a good ground connection. Check all fuses.
+ Check the protection LED is not lit.
PROTECTION LED ILLUMINATES WHEN AMPLIFIER IS POWERED UP
+ Check shorts on speaker wires.
+ Remove speaker wires and reset the amplifier. If the protection LED still
comes on, then the amplifier is faulty.
FUSE BLOWING
+ Check that the minimum speaker impedance is correct.
+ Check short on power cable and vehicle chassis.
OVERHEATING
+ Check that the minimum speaker impedance is correct.
+ Check speaker shorts.
+ Check that there is a good airflow around the amplifier.
SOUND TOO LOW-DISTORTED SOUND
+ Check that the input level control is set to match the output level of the unit.
+ Check the head unit volume.
+ Check speaker shorts.
+ Check that crossover frequencies have been properly set.
HIGH HISS-ENGINE NOISE IN SPEAKERS
+ Check a good ground and for speaker shorts.
& Disconnect all RCA inputs from the amplifier. If hiss/noise disappears, check
it with a good RCA interconnect. Then check the component driving the
amplifier.
-11-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising