f i r e - p a r t s . c o m

f i r e - p a r t s . c o m
Installation Manual
Installation & Appliance Set-Up
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT DISCARD THIS MANUAL
WARNING
If the information in these instructions is not followed exactly, a
fire could result causing property
damage, personal injury, or death.
MT. VERNON E2 INSERT
PELLET STOVE
Model(s):
MTVI-E2-MBK
MTVI-E2-CSB
MTVI-E2-PMH
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire - If heater or chimney connector glows, you are overfiring. Overfiring
will void your warranty.
fire-parts.com
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
WARNING
Tested and
Listed by
O-T L
C
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
Portland
Oregon USA
US
OMNI-Test Laboratories, Inc.
061-S-84-2
Please read this entire manual before installation and use of this
pellet fuel-burning room heater. Failure to follow these instructions
could result in property damage, bodily injury or even death.
CAUTION
Tested and approved for wood pellets and shelled
corn only. Burning of any other type of fuel voids your
warranty.
NOTE
Hot glass will cause burns.
•
Do not touch glass until it is cooled
•
NEVER allow children to touch glass
•
Keep children away
•
CAREFULLY SUPERVISE children in same room as
fireplace.
•
Alert children and adults to hazards of high temperatures
•
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other flammable
materials away.
A 2:1 mix of pellets to corn is approved, but may require the
firepot to be cleaned more frequently.
CAUTION
NOTE
To obtain a French translation of this manual, please contact
your dealer or visit www.quadrafire.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrafire.com
00
1
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and national codes and regulations.
• Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.
7082-131D
October 28, 2014
MT VERNON E2 INSERT
Safety Alert Key:
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
•
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
•
NOTICE: Indicates practices which may cause damage to the appliance or to property.
TABLE OF CONTENTS
1 Important Safety Information .............3 4 Vent Information................................12
A. Appliance Certification ......................................................3
B. BTU & Efficiency Specifications........................................3
C. Glass Specifications .........................................................3
D. Electrical Rating................................................................3
E. Mobile Home Approved ....................................................3
F. Non-Combustible Materials ................................................3
G. Combustible Materials .......................................................3
2 Getting Started ....................................4
A. Design, Installation & Location Considerations ..........................4
B. Remote Thermostat Location ............................................5
C. Tools And Supplies Needed..............................................5
D. Inspect Appliance and Components .................................5
E. Install Checklist ..................................................................6
A. Venting Termination Minimum Requirements ...................12
B. Avoiding Smoke and Odors ...............................................13
C. Negative Pressure ............................................................14
D. Draft........ ..........................................................................14
E. Chimney and Exhaust Connection ..................................14
F. Equivalent Feet of Pipe ....................................................15
G. Pipe Selection Chart ........................................................15
5 Venting Systems ...............................16
A. Full Reline With Outside Air - Horizontal ..........................16
B. Full Reline With Outside Air - Vertical ..............................17
6 Appliance Set-Up ..............................18
A. Leveling System ...............................................................18
B. Outside Air Kit Instructions ................................................18
C. Hearth Support .................................................................18
D. Removal of Cast Sides ....................................................19
E. Surround and Trim Set - Cast ...........................................19
F. Surround & Trim Set, Basic ...............................................20
G. Optional Log Set Placement Instructions ..........................20
H. Remote Thermostat Installation .......................................21
I. Power Cord .........................................................................21
fire-parts.com
3 Dimensions and Clearances ..............7
A. Appliance Dimensions ......................................................7
B. Clearance To Combustibles, US & Canada .......................8
C. Masonry & Zero Clearance Fireplaces .............................9
D. Floor Protection ................................................................9
E. Minimum Opening for Masonry & Zero Clearance
Fireplaces..........................................................................9
F. Installation into a Factory-Built Fireplace...........................10
G. Installation into a Masonry Fireplace ................................11
H. Prefabricated Metal Chimney ...........................................11
7 Mobile Home Installation..................22
8 Accessory List ..................................23
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
2
7082-131D
October 28, 2014
MT VERNON E2 INSERT
1
Important Safety Information
• The structural integrity of the mobile home floor, ceiling,
and walls must be maintained.
A. Appliance Certification
Model
Mt. Vernon Insert Pellet Stove E2
Laboratory
OMNI Test Laboratories, Inc.
Report No.
061-S-84-2
• The appliance must be properly grounded to the frame
of the mobile home and use only Listed pellet vent Class “L”
or “PL” connector pipe.
Type
Solid Fuel Room Heater, Pellet and
Shelled Corn Fuel Burning Type
• Outside Air Kit (OAK-3) must be installed in a mobile
home installation.
Standard
ASTM E1509-12, ULC-S628-93 and
(UM) 84-HUD, Mobile Home Approved.
F. Non-Combustible Materials
FCC
Complies with Part 15 of FCC Rules.
Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.
The Quadra-Fire Mt. Vernon E2 Insert Pellet Stove meets the
U.S. Environmental Protection Agency’s 1990 particulate emission
standards.
Material which will not ignite and burn, composed of any
combination of the following:
- Steel
- Plaster
- Brick
- Iron
- Concrete
- Tile
- Glass
- Slate
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace of 750° C.
fire-parts.com
NOTICE: This installation must conform with local codes. In
the absence of local codes you must comply with the ASTM
E1509-12, ULC S628-93, (UM) 84-HUD and ULC/ORDC-1482.
B. BTU & Efficiency Specifications
G. Combustible Materials
Material made of/or surfaced with any of the following
materials:
- Wood
- Compressed Paper
- Plant Fibers
- Plastic
- Plywood/OSB
- Sheet Rock (drywall)
Any material that can ignite and burn: flame proofed or not,
plastered or un-plastered.
EPA Certified:
1.7 grams per hour
EPA Certification
Number and Date:
Number: 926
Issued: 2014
Efficiency:
86.5%
BTU Input
EPA: 18,000 to 52,500
Fire Risk.
BTU Output:
EPA: 13,800 to 37,600
Vent Size:
3” or 4” Type ‘L’ or ‘PL’
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Fuel:
Wood Pellets & Shelled Corn
WARNING
*BTU will vary, depending on the type of fuel you use in your
appliance. Consult your Quadra-Fire dealer for best results.
C. Glass Specifications
This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved by
Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with unit).
• Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
D. Electrical Rating
E. Mobile Home Approved
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
• This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps
October 28, 2014
7082-131D
3
MT VERNON E2 INSERT
2
Install Guide
Getting Started
A. Design, Installation & Location Considerations
1. Appliance Location
NOTICE: Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
•
Consult insurance carrier, local building inspector, fire
officials or authorities having jurisdiction over restrictions,
installation inspection and permits.
Since pellet exhaust can contain ash, soot or sparks, you
must consider the location of:
•
•
•
•
•
•
Windows
Air Intakes
Air Conditioner
Overhang, soffits, porch roofs, adjacent walls
Landscaping, vegetation
Horizontal or vertical vent termination
It is a good idea to plan your installation on paper, using exact
measurements for clearances and floor protection, before
actually beginning the installation. Location of the appliance
and chimney will affect performance.
2. Floor Support
Consideration must be given to:
Ensure that your floor will support these weights prior to
installation. Add sufficient additional support to meet this
weight requirement prior to installation. The weight of the
appliance is 510 lbs. with a full load of fuel the max weight
is 557 lbs.
• Safety, convenience, traffic flow
• Placement of the chimney and chimney connector and to
minimize the use of chimney offsets.
The supporting floor under the appliance must be able to
handle the weight of the appliance, fuel load and the weight
of the chimney.
fire-parts.com
• Place the appliance where there will be a clear passage
for a Listed chimney through the ceiling and roof (vertical)
or through exterior wall (horizontal).
• Installing the required outside air kit will affect the location
of the vent termination.
When locating vent and venting termination, the ideal location is to vent above roof line when possible. This minimizes
the affects of wind loading.
Recommended Location:
• Above peak
WARNING
Risk of Fire! Damaged parts could impair safe operation.
Do NOT install damaged, incomplete or substitute components.
Recommended Location:
• Above peak
• Inside heated space
Marginal Location:
• Below peak
Marginal Location:
• Wind loading possible
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Recommended:
• Insulated exterior chase
in cooler climates
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Windward
Leeward
Recommended:
Outside Air Intake
on windward side
Multi-level Roofs
NOT recommended:
Outside Air Intake
on leeward side
Figure 4.1
4
7082-131D
October 28, 2014
MT VERNON E2 INSERT
B. Remote Thermostat Location
D. Inspect Appliance and Components
The thermostat wall control’s location will have some affect
on the appliance’s operation.
•
Open the appliance and remove all the parts and articles
packed inside the Component Pack. Inspect all the parts
and glass for shipping damage.
•
Report to your dealer any parts damaged in shipment.
•
All labels have been removed from the glass door.
•
Plated surfaces have been wiped clean with a soft cloth,
if applicable.
•
Read all the instructions before starting the installation.
Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
•
Follow pipe manufacturer instructions for installation
and air clearance requirements.
• When located close to the appliance, it may require a
slightly higher temperature setting to keep the rest of the
house comfortable.
• When located in an adjacent room or on a different floor
level, you will notice higher temperatures near the appliance.
CAUTION! The remote thermostat is an integral part of the
appliance. No other wall control or thermostat can be
substituted.
WARNING
Risk of Fire!
Damaged parts could impair safe operation.
Do NOT install damaged, incomplete or
substitute components.
fire-parts.com
MODE/SET
WARNING
Figure 5.1
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
**HHT recommends a range of 20 feet for best performance
•
C. Tools And Supplies Needed
Tools and building supplies normally required
for installation, unless installing into an existing
masonry fireplace:
•
Reciprocating Saw
Hammer
Tape Measure
1/4” Self-Tapping Screws
Hi-temp Caulking Material
Safety Glasses
Electric Drill & Bits (1/4”)
Channel Locks
Phillips Screwdriver
Plumb Line
Framing Material
Gloves
Framing Square
Level
•
•
May also need:
Vent Support Straps
Venting Paint
October 28, 2014
•
Installation and use of any damaged
appliance.
• Modification of the appliance.
Installation other than as instructed by Hearth & Home
Technologies.
Installation and/or use of any component part not approved by
Hearth & Home Technologies.
Operating appliance without fully assembling all components.
Do NOT Overfire
Or any such action that may cause a fire hazard.
NOTE: Upon removing the appliance from the fireplace
a tag shall be permanently attached to the fireplace
indicating it has been altered and should be inspected
by a qualified person prior to re-use as a convectional
fireplace (tag included in component pack).
7082-131D
5
MT VERNON E2 INSERT
E. Install Checklist
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
Customer:
Date Installed:
Lot/Address:
Location of Fireplace:
Installer:
Dealer/ Distributor Phone #:
Serial #:
Model (circle one):
MTVI-E2-MBK
MTVI-E2-CSB
MTVI-E2-PMH
WARNING! Risk of Fire or Explosion! Failure to install fireplace according to these instructions can lead to a fire or explosion.
Appliance Install
YES
IF NO, WHY?
Required non-combustible floor protection (Pg. 8)
Verified clearance to combustible (Pg. 8)
Unit is leveled and secured (Pg. 17)
Venting/Chimney Section 4 (Pg. 12)
fire-parts.com
Venting configuration complies with diagrams
Venting installed, sealed and secured in place with proper clearance
Exterior wall/roof flashing installed and sealed
Terminations installed and sealed
OAK installed and sealed (if needed) (Pg. 18)
Electrical
120VAC unswitched power provided to the appliance (Pg. 21)
Appliance Setup Section 5 (Pg. 18)
All packaging and protective materials removed
Accessories installed properly
Started appliance and verified that all motors and blowers operate as the should
Manual bag and all of its contents are removed from inside/under the fireplace
and given to the party responsible for use and operation.
Hearth & Home Technologies recommends the following:
• Photographing the installation and copying this checklist for your file.
• That this checklist remain visible at all times on the fireplace until the installation is complete.
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:
Comments communicated to party responsible
by
on
(Builder/Gen. Contractor)
(Installer)
(Date)
Part # 4017-254 • Rev B • 01/29/13
6
7082-131D
October 28, 2014
MT VERNON E2 INSERT
3
Dimensions and Clearances
A. Appliance Dimensions
16-1/2 [419]
32 [812]
23-7/8 [606]
7/8
[23]
15
[382]
29-3/4
[756]
23-7/8
[605]
13-1/8
[333]
26-1/4 [667]
26-7/8 [683]
fire-parts.com
Figure 7.1 - Top View
Figure 7.3 - Side View
36-5/8 [930]
33
[838]
34-7/8
[886]
50 [1270]
46-1/8 [1171]
Figure 7.2 - Front View with Basic Surround Panel Set
October 28, 2014
Figure 7.4 - Front View with Cast Panel Set
7082-131D
7
MT VERNON E2 INSERT
B. Clearance To Combustibles, US & Canada
Built-in Unit - Rear Vent
B
A
A
C
Figure 8.1
Location
Configuration
Inches
Millimeters
fire-parts.com
A
Side of Outside Skin
Top or Rear Vent
2
51
B
Vent Pipe to Combustible
Top or Rear Vent
3
76
C
Cast Side to Side Wall
Top or Rear Vent
6
152
Built-in Unit - Rear Vent with Outside Air
Fire Risk.
Comply with all minimum clearances to
combustibles as specified.
Failure to comply may cause house
fire.
J
3 in
[76mm]
Note: In Canada where passage through a
wall or partition of combustible construction is
desired, the installation shall conform to
CAN/CSA-B365.
K
3 in
[76mm]
6 in
[152mm]
3 in
[76mm]
Outside
Air
Figure 8.2
8
WARNING
7082-131D
Through the wall, horizontal termination cap
must be a minimum of 6” (152mm) from the
wall. Approved for mobile home installations.
Must use 3” or 4” (76-102mm) “L” or “PL”
listed pellet venting or listed double wall pipe
and a Quadrafire outside air kit (OAK3) in
mobile homes.
Note:
• Illustrations reflect typical installations and
are FOR DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual
design preference.
October 28, 2014
MT VERNON E2 INSERT
Built-In Vertical
D. Floor Protection
J
Inches
Location
3 in
[76mm]
K
•
•
Millimeters
D
Floor protection hearth extension from
door opening
6
152
E
Floor protection to the side of door
opening
6
152
Use a non-combustible floor protector, extending beneath
appliance and to the front, and sides as indicated.
If employing a hearth extension, any parts or materials used in
construction must be non-combustible.
E. Minimum Opening for Masonry & Zero
Clearance Fireplaces
Outside
Air
Figure 9.1
The maximum mantel depth (J) is 12 inches (305mm) with a
minimum vertical height (K) of 12 inches (305mm).
fire-parts.com
However if your mantel has a depth of 10 inches (254mm)
then the vertical minimum height is 10 inches (254mm).
H
G
F
I
C. Masonry & Zero Clearance Fireplaces
Figure 9.3
Mantel
F
Side Wall
B
A
C
E
D
Location
Inches
Millimeters
Rear Width
24
610
G
Depth
16-1/2
381
H
Height
23-7/8
606
I
Front Width
34
864
2-1/4
Figure 9.2
Location
Inches
Millimeters
A
Insert side to combustible side wall
6
152
B
Insert top to max. 2-1/4 inch face trim
0
0
C
Insert side to max. 2-1/4 inch face trim
0
0
** Face Trim not to exceed 3/4”
October 28, 2014
7082-131D
9
MT VERNON E2 INSERT
F. Installation into a Factory-Built Fireplace
The following modifications are permissible:
•
•
•
•
•
•
•
•
The following is only one example as there are many different models of factory-built fireplaces.
NOTE: This example is for reference only. Any modifications must not compromise the structural integrity
or reduce the protection for combustible materials.
Removal of damper or locked in open position
Removal of smoke shelf or baffle
Removal of ember catches
Removel of fire grate
Removal of view screen/curtain
Removal of doors
Removal of factory-built fireplace floor
External trim pieces which do not affect the operation of
the fireplace may be removed providing they can be stored
on or within the fireplace for reassembly if the insert is
removed.
•
The permanent metal warning label provided must be
attached to the back of the fireplace, with screws or
nails, stating that the fireplace may have been altered to
accommodate the insert, and must be returned to original
WARNING
THIS FIREPLACE MAY HAVE BEEN ALTERED
TO ACCOMMODATE AN INSERT. IT MUST BE
RETURNED TO ITS ORIGINAL CONDITION
BEFORE USE AS A SOLID FUEL BURNING
FIREPLACE.
250-2061
250-2061
Starter hole
Mark area of
floor to cut
Figure 10.2. Measure and mark the metal
floor for cutting. With a drill, make a starter
hole in each corner.
fire-parts.com
Figure 10.1
condition for use as a conventional fireplace. Figure 10.1
•
If the hearth extension is lower than the fireplace opening,
the portion of the insert extending onto the hearth must be
supported.
•
Manufacturer designed adjustable support kit can be
ordered from your dealer.
NOTE: Refer to chimney liner manufacturer for recommendations on supporting the liner. Installation
into fireplaces without a permit will void the listing.•
•
•
•
The firebrick (refractory), glass doors, screen rails,
screen mesh and log grates can be removed from a factory-built firebox in order to gain minimum insert opening requirements.
Any smoke shelves, shields and baffles may be removed
from a factory-built firebox if attached with mechanical
fasteners.
Figure 10.3. Using a saws-all, cut out the
floor.
Use 2 x 4 from insert
packaging to support insert
The metal floor of the factory-built firebox may be
removed to facilitate the installation of the insert only
when a 1 inch (25mm) airspace is provided between the
insert and the floor of outer wrap.
Figure 10.4. If the floor is made of thin
metal, we recommend using the 2 x 4 from
the insert packaging to support the insert.
The 2 x 4 may need to be cut to the appropriate size.
10
7082-131D
October 28, 2014
MT VERNON E2 INSERT
H. Prefabricated Metal Chimney
Example Removal of Factory-Built Fireplace Cont.
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements:
• Must be minimum 6 inch (152mm) inside diameter of
high temperature chimney listed to UL 103 HT (2100oF)
or ULC-S628.
Keep sharp edge of
metal floor away from
power cord
• Must use components required by the manufacturer for
installation.
• Must maintain clearances required by the manufacturer
for installation.
• Refer to manufacturers instructions for installation
•This insert is listed to ASTM E 1509-12 Standard and
is approved for installation into listed factory-built zero
clearance fireplaces listed to UL 127 conforming to the
following specifications and instructions:
Figure 11.1. Place the insert into the factory-built firebox. Ensure that the power cord
can not be damaged by the sharp metal
edge. You may need to cut out a notch to
accommodate the cord.
•The original factory-built clearance fireplace chimney
cap must be re-installed after installing the approved
chimney liner meeting type UL 103 HT requirements
(2100°F) per UL 1777.
•If the chimney is not listed as meeting HT requirements,
or if the factory built fireplace was tested prior to 1998, a
full height listed chimney liner must be installed from the
appliance flue collar to the chimney top.
fire-parts.com
Leveling Leg
1”
•The liner must be securely attached to the insert flue collar
and the chimney top.
•The air flow of the factory-built zero-clearance fireplace
system must not be altered. The flue liner top support
attachment must not reduce the air flow for the existing
air-cooled chimney system.
Figure 11.2. Ensure that the leveling leg is
positioned over the 2 x 4 before leveling the
insert. Minimum 1” clearance.
•No dilution air is allowed to enter the chimney.
1. Secure the fireplace damper in the open position. If
this cannot be accomplished, it will be necessary to
remove the damper
2. Seal damper area of chimney around chimney
connector with a high temperature sealant or seal
insert against the face of the fireplace.
G. Installation into a Masonry Fireplace
All modifications that can be made to a Factory Built Fireplace can be made to a Masonry Fireplace.
3. Both methods must be removable and replaceable
for cleaning and re-installation.
In addition DO NOT remove any brick or mortar from the
existing fireplace.
WARNING
Risk of Fire!
WARNING
•
Removing floor of fireplace must not weaken structure
of firebox or reduce protection for combustible materials.
•
Final approval of this installation type is contingent upon
the appropriate local authority having jurisdiction.
October 28, 2014
Follow venting manufacturer’s clearances and
instructions when installing venting system.
NOTICE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF)
[1149oC] CLASS “A” or conforming to CAN/ULCS629M, STANDARD FOR 650oC FACTORY-BUILT
CHIMNEYS.
7082-131D
11
MT VERNON E2 INSERT
4
Vent Information
A. Venting Termination Minimum Requirements
V
N
V
N
Inside Corner
Electrical
Service
N
V
N
V
G
V
A
D
O
V
H
P
E
L
C
V B
FIXED
CLOSED
V
F
FIXED
CLOSED
OPEN
V
B
OPEN
G
M
V
V
V Termination Cap
I
A
B
B
X Air Supply Inlet
V
X
J or K
G Gas Meter
Restricted Area
Figure 12.1
All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.
fire-parts.com
A
12 in.
Above Finish Grade (the grade surface
must be a non-combustible material
24 in.
Above grass, top of plants, wood or any other combustible
B
12 in.
48 in. no OAK
Open door or window: below or to the side
12 in.
36 in. no OAK
Clearance from any forced air intake of other appliance
B
12 in.
Open door or window: above
12 in.
Clearance horizontally from combustible wall
C
6 in.
Permanently closed window: above, below
or to the side
15 in.
Vented directly through a wall, minimum length of
horizontal pipe
D
18 in.
36 in. no OAK
Vertical clearance to a ventilated soffit
located above the terminal within a horizontal distance of 2 ft from the center-line
of the terminal
6 in. horizontal
12 in. vertical
Minimum horizontal or vertical terminations must
protrude from wall
NOTICE:
E
12 in.
Clearance to unventilated soffit
Do NOT Terminate Vent:
F
12 in.
Clearance to outside corner
•
G
12 in.
Clearance to inside corner
In any location that will allow flue gases or soot from entering or staining the building
H
36 in.
Above gas meter/regulator measured from
horizontal center-line of regulator
•
In any location which could create a nuisance or hazard
I
36 in. USA
72 in. Canada
Clearance to service regulator vent outlet
•
J
12 in.
48 in. no OAK
Clearance to non-mechanical air supply
inlet to the building or the combustions air
inlet to any other appliance
In any enclosed or semi-enclosed area such as a carport,
garage, attic, crawl space, under a sun deck or porch,
narrow walkway
•
K
10 ft horizontal
3 ft vertical
Clearance to mechanical air supply
Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
L
7 ft.
Above paved sidewalk, paved driveway
located on public property
M
12 in.
Under an open veranda, porch, deck or
balcony
N
See Note
below*
Electric service: above, below or to the
side (location must not obstruct or interfere
with access)
O
24 in.
Adjacent building, fences and protruding
parts of the structure
P
12 in.
Clearance above roof line for vertical
terminations
NOTICE:
Termination must exhaust above air inlet elevation.
*NOTE: Consult local building, fire officials or authorities having jurisdiction. Local codes or regulations may require different clearances.
12
•
It is recommended that at least 60 inches (1.52m) of vertical
pipe be installed when appliance is vented directly through a
wall. This will create a natural draft, which will help prevent
the possibility of smoke or odor venting into the home during
a power outage.
•
It will also keep exhaust from causing a nuisance or hazard
by exposing people or shrubs to high temperatures.
•
The safest and preferred venting method is to extend the vent
vertically through the roof or above the roof.
7082-131D
October 28, 2014
MT VERNON E2 INSERT
B. Avoiding Smoke and Odors
Vent Configurations
Negative Pressure, Shut-Down and Electrical Power
Failure
To reduce the probability of back-drafting or burn-back in
the pellet appliance during power failure or shut down conditions, it must be able to draft naturally without exhaust
blower operation.
To reduce probability of reverse drafting during shut-down
conditions Hearth & Home Technologies strongly recommends:
• Installing the pellet vent with a minimum vertical run of
5 feet (1.52m). Preferably terminating above the roof
line.
Negative pressure in the house will resist this natural draft if
not accounted for in the pellet appliance installation.
Heat rises in the house and leaks out at upper levels. This
air must be replaced with cold air from outdoors which flows
into lower levels of the house.
Vents and chimneys into basements and lower levels of the
house can become the conduit for air supply and reverse
under these conditions.
Outside Air
An outside air kit is recommended in all installations and
must be ordered separately.
Per national building codes, consideration must be given to
combustion air supply to all combustion appliances. Failure
to supply adequate combustion air for all appliance demands
may lead to backdrafting of those and other appliances.
•
Installing the outside air kit at least 4 feet (1.22m) below
the vent termination.
To prevent soot damage to exterior walls of the house and to
prevent re-entry of soot or ash into the house:
•
Maintain specified clearances to windows, doors and
air inlets, including air conditioners.
•
Vents should not be placed below ventilated soffits.
Run the vent above the roof.
•
Avoid venting into alcove locations.
•
Vents should not terminate under overhangs, decks or
onto covered porches.
•
Maintain minimum clearance of 12 inches (305mm)
from the vent termination to the exterior wall. If you
see deposits developing on the wall, you may need to
extend this distance to accommodate your installation
conditions.
fire-parts.com
When the appliance is roof vented (strongly recommended):
The air intake is best located on the exterior wall oriented
towards the prevailing wind direction during the heating
season.
When the appliance is side-wall vented:
The air intake is best located on the same exterior wall as
the exhaust vent outlet and located lower on the wall than
the exhaust vent outlet.
The outside air supply kit can supply most of the demands of
the pellet appliance, but consideration must be given to the
total house demand.
House demand may consume the air needed for the appliance. It may be necessary to add additional ventilation to
the space in which the pellet appliance is located.
Consult with your local HVAC professional to determine the
ventilation demands for your house.
CAUTION
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT
OR SYSTEM.
October 28, 2014
7082-131D
13
MT VERNON E2 INSERT
C. Negative Pressure
•
•
•
•
WARNING
Risk of Asphyxiation!
Negative pressure can cause spillage of combustion
fumes and soot.
Inadequate draft due to environmental conditions
Downdrafts
Tight sealing construction of the structure
Mechanical exhausting devices
E. Chimney and Exhaust Connection
1. Chimney & Connector: Use 3 or 4 inch (76-102mm) diameter
Negative pressure results from the imbalance of air available for the appliance to operate properly. It can be strongest
in lower levels of the house.
Causes include:
•
Exhaust fans (kitchen, bath, etc.)
•
Range hoods
•
Combustion air requirements for furnaces, water heaters
and other combustion appliances
•
Clothes dryers
•
Location of return-air vents to furnace or air conditioning
•
Imbalances of the HVAC air handling system
•
Upper level air leaks such as:
type “L” or “PL” venting system. It can be vented vertically or
horizontally.
NOTE: The appliance exhaust outlet is designed to accommodate 3 inch venting. Use of 4 inch venting requires
the use of a 3-to-4 inch exhaust vent increaser in addition
to any other venting components needed, sold separately.
2. Mobile Home: Approved for all Listed pellet vent. If using the 3
to 6 inch (76-152mm) Top Vent Offset Adapter, use Listed double
wall flue connector. A Quadra-Fire Outside Air Kit (OAK-3) must
be used with manufactured home installations.
3. Residential: The 3 inch (76mm) vertical Top Vent Adapter Kit and
the 3 to 6 inch (76-152mm) Top Vent Offset Adapter are tested
to use 24 gauge single wall flue connector or Listed double wall
flue connector to Class A Listed metal chimneys, or masonry
chimneys meeting International Residential Code standards for
solid fuel appliances.
fire-parts.com
- Recessed lighting
- Attic hatch
- Duct leaks
To minimize the effects of negative air pressure:
4. INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
•
Install the outside air kit with the intake facing prevailing
winds during the heating season
5. Vent Assembly to Insert Instructions:
•
Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
•
Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the appliance
a. Unlatch the vent assembly for the exhaust blower and
attach to the vent pipe end using high temperature
silicone and at least three screws.
•
Avoid installing the appliance near doors, walkways or
small isolated spaces
b. Slide the appliance into place and line up the bent
assembly with the exhaust blower.
•
Recessed lighting should be a “sealed can” design
c. Make sure the high-temperature gasket is in place.
•
Attic hatches weather stripped or sealed
d. Latch the top vent assembly to the exhaust blower.
•
Attic mounted duct work and air handler joints and seams
taped or sealed
D. Draft
Draft is the pressure difference needed to vent an appliance successfully. When an appliance is drafting successfully, all combustion byproducts are exiting the home
through the chimney.
Install through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially
during lighting and die-down of the fire.
These instructions are for connecting the vent pipe to the
vent assembly prior to installing the appliance in the fireplace.
6. DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
7. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING
ANOTHER APPLIANCE.
8. Disconnect the vent pipe from the appliance to allow removal
of the fireplace insert for the purpose of inspecting the fireplace
insert and the fireplace.
NOTE: All pipe must be welded seam pipe whenever possible.
Seal pipe joints with high temperature silicone (500°F [260°C]
minimum rated only).
Considerations for successful draft include:
•
•
Preventing negative pressure
Location of appliance and chimney
WARNING
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of the chimney
system caused by:
14
USE ONLY RECOMMENDED VENTING COMPONENTS;
OTHERWISE MAKESHIFT PARTS MAY RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
7082-131D
October 28, 2014
MT VERNON E2 INSERT
F. Equivalent Feet of Pipe
WARNING
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent size.
Figure 15.1.
Vent surfaces get HOT, can cause burns if
touched. Non-combustible shielding or guards
may be required.
Example of 3 Elbow-Rear Vent Termination Calculation
2 ft.
Pellet Venting
Component
# of
Elbows
90o Elbow or Tee
3
Feet of Multiplied
Pipe
By
45o Elbow
3 ft.
Equivalent
Feet
Equivalent Feet
Components
X
5
15
X
3
Horizontal Pipe
7
X
1
7
Vertical Pipe
2
X
0.5
1
Total Equivalent Feet
23
2 ft.
Note: This is a generic example and is not
intended to represent any specific fuel type.
2 ft.
Figure 15.1
fire-parts.com
30
G. Pipe Selection Chart
4 in. (102mm) Diameter Pipe Only
Example 1
The chart will help you in determining proper venting size
according to the equivalent feet of pipe calculated previously
and the altitude above sea level of this installation.
Figure 15.2
20
Equivalent Pipe
Length In Feet
Example 2
a. Locate the calculated equivalent feet of pipe on the vertical
left side of the chart.
10
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
0
b. Move to the right horizontally on the chart until you reach
your altitude above sea level.
1
2
3
4
5
6
7
8
9
10
ALTITUDE IN THOUSANDS OF FEET
c. If you fall below the diagonal line, 3 or 4 inch (76 to 102mm)
pipe may be used.
Figure 15.2
d. If it is anywhere above the diagonal line, a 4 inch (102mm)
diameter pipe is required.
Example 1: If the equivalent length of pipe is 23 feet (7m) with
altitude of 8,000 feet (2438m) you must use 4 inch (102mm)
diameter type “L” or “PL” vent.
NOTICE:
•
A 90° elbow is 5 times as restrictive to the flow of exhaust
gases under positive pressure as 1 foot (305mm) of horizontal pipe.
•
A foot of horizontal pipe is twice as restrictive as a foot of
vertical pipe.
Example 2: If the equivalent length of pipe is 12 feet (3.7m)
with altitude of 6,000 feet (1829m) you may use 3 or 4 inch
(76 to 102mm) diameter type “L” or “PL” vent.
WARNING
WARNING
RISK OF INJURY OR PROPERTY DAMAGE!
Risk of Fire!
•
Only LISTED venting components may be used.
•
NO OTHER vent components may be used.
• Substitute or damaged vent components may impair
safe operation.
October 28, 2014
•
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
•
Refer to the owner’s information manual provided with this
appliance.
•
For assistance or additional information consult a qualified
installer, service agency or your dealer.
7082-131D
15
MT VERNON E2 INSERT
5
Venting Systems
A. Full Reline With Outside Air - Horizontal
WARNING
Fire Risk.
Inspection of Chimney:
• Masonry chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be a minimum 6 inch
(152mm) UL103 HT.
CAUTION
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
fire-parts.com
NOTE: Use metal plate around
exhaust vent pipe and seal all edges
with non-flammable insulation such
as fiberglass, mineral wool or
ceramic.
Do not use high temperature
caulking materials to seal any edge
to prevent future serviceability.
Outside Air
Termination
Figure 16.1
NOTE:
In Canada, where passage through a wall or partition of combustible construction is desired, the installation shall conform
to CAN/CSA-B365.
16
NOTE:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
7082-131D
October 28, 2014
MT VERNON E2 INSERT
B. Full Reline With Outside Air - Vertical
NOTE: Check clearances carefully for this type of installation to ensure adequate room for outside air venting.
NOTE: In Canada only a full reline is allowed per ULC
S628, ORD ULC C1482-M1990.
12 in [305mm]
min. below
12 in [305mm]
min. below
fire-parts.com
Outside Air
Termination at
Chimney Top
(Vertical)
NOTE: Use metal plate around
exhaust vent pipe and seal all edges
with non-flammable insulation such
as fiberglass, mineral wool or
ceramic.
Do not use high temperature
caulking materials to seal any edge
to prevent future serviceability.
Figure 17.1
NOTE: In Canada this fireplace insert must be installed
with a continuous chimney liner of 6 inch (152mm) diameter extending from the fireplace insert to the top of the
chimney. The chimney liner must conform to the Class 3
requirements of CAN/ULC-S635, Standard for Lining Systems for Existing Masonry or Factory-Built Chimneys and
Vents, or CAN/ULC-S640, Standard for Lining Systems for
New Masonry Chimneys.
October 28, 2014
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.
7082-131D
17
MT VERNON E2 INSERT
6
Appliance Set-Up
A. Leveling System
The leveling bolts are located on the sides of the appliance,
front and rear. To access the bolts, remove the front access
panels. Reach in and turn the bolt to the desired height to
level the appliance. Figure 18.1
Collar
Wire Ties
Lower the leveling
bolts if necessary to
keep the insert level
when installing.
3 inch Aluminum Flex
Pipe (not included)
Trim Ring
Termination Cap
Figure 18.2 - OAK Exploded View
C. Hearth Support
fire-parts.com
Included in Kit: (1) bottom, (1) trim front, (2) trim sides, (2)
trim extensions
Figure 18.1
Tools Needed: Phillips head screw driver, measuring tape,
gloves
B. Outside Air Kit Instructions
1. Remove contents from box and lay on protective surface
to avoid scratching the paint.
Included in Kit: 2 wire ties, 1 collar assembly,
1 termination cap assembly, 1 trim ring, fasteners.
3 INCH (76mm) ALUMINUM FLEX PIPE NOT INCLUDED
2. Lay front and sides face down. Bend the tabs down toward
the inside. Figure 18.3
3. The side pieces are shipped flat. It is must easier to flex the
sides into a bowed position before installing.
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
1. Measure distance from floor to air vent opening in appliance and mark location on wall.
2. Use saw to cut opening in wall. Cut a 3-1/2 to 4 inch
(89-102mm) opening on inside wall and a 4 to 4-1/2 inch
(102-114mm) opening on outside of house.
3. Use wire ties to secure flex pipe to collar assembly.
4. Slide trim ring over flex pipe and run pipe through wall.
5. Attach flex pipe (not included) to outside termination cap
with second wire tie.
6. Secure termination cap to outside surface.
7. Secure trim ring to interior wall.
4. Lay the cast bottom face up. Attach the 2 sides FIRST and
then the front piece. Figure 19.1 on pg. 19
5. Turn the cast bottom right side up and attach the panel
extensions. Note the alignment hole.
6. Attach the appropriate footers depending on the panels &
trim set you are installing. The footers come in 2 sizes, 3
and 5 inches. Discard the footers not used.
7. Place the assembled hearth support under the insert.
Lower the leveling bolts if necessary to keep the insert
level.
8. Open the door and attach the hearth support to the insert.
There are 9 attachment holes. Figure 19.2 on pg. 19
CAUTION
Bend tabs down. Shipped
flat from the factory.
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
Figure 18.3
18
7082-131D
October 28, 2014
MT VERNON E2 INSERT
E. Surround and Trim Set - Cast
Included in Surround Kit: (2) side panels, left and right;
(1) panel top; (1) fastener package.
3 inch
high Set
Attach Trim to Insert from
inside Insert.
Included in Cast Trim Kit: (2) cast trim legs, left and right;
(1) cast trim header; (2) cast trim footers, left and right; (1)
fastener package.
5 inch
high Set
Tools Needed: Powered Phillips head screw driver
3 in
Basic
1. Remove contents from box being careful not to scratch or
damage the cast trim pieces.
Cast
5 in
Install Front Trim Last,
Corner Overlap Side
Trim Pieces
2. Lay the surround set face down on protective covering to
prevent scratching the painted surface.
3. Secure the surround legs to top panel with the screws
provided.
Attach Trim to Base
from underneath
Figure 19.1
4. Now bend the tabs down toward the backside of the panel
set, 5 on top and 2 on each leg. Leave the panel set face
down. Figure 19.4
5. Place the corresponding cast trim pieces ( 2 cast trim legs
and 1 cast trim header) underneath the panel set, also face
down.
9 attachment holes - 3 on
each side and 3 in the front
6. Place washer provided over tab and secure the trim and
panel together with screw. Continue for all tabs.
fire-parts.com
7. Secure cast footers with screws.
Figure 19.2
8. Remove both left and right cast sides from insert. See
Figure 19.3.
9. Carefully slide surround and trim over the top of the
insert into place matching the mounting holes on the
panel with the mounting holes on the insert. Secure with
screws provided.
2. Bend tabs down
D. Removal of Cast Sides
Remove the right side panel by releasing the upper, springloaded latch. Access the latch through the upper panel vent
holes. The cast panel should fall forward. Lift it out of its
lower nest and set the panel aside. You may need to disconnect the dial control wire harness.
1. Screw panels
together
1. Screw panels
together
2. Bend tabs
down
3. Install Cast Trim Header
Location of Latch
for Removing
Cast Sides
Figure 19.4
Lower the leveling
bolts if necessary to
keep the insert level
when installing the
Hearth Support.
Figure 19.3 - Shown with Cast Panel Set
Figure 19.5- Completed View
October 28, 2014
7082-131D
19
MT VERNON E2 INSERT
F. Surround & Trim Set, Basic
Included in Surround & Trim Kit: (2) corner brackets and set
screws; (1) trim set, 3 piece; (2) side panels; (1) top panel;
(4) screws.
G. Optional Log Set Placement Instructions
2 PIECE LOG SET INSTALLATION
Tools Needed: Powered Phillips head screw driver
1. Place the left log as shown. There are 2 indentations in
the bottom of the log to fit over the screw heads in the
firebox. Figures 20.4 & 20.5
1. Secure the top panel to the surround sides with the
screws provided. Figure 20.1
2. Place the right log in front of the 2 screw heads in the
firebox. Figures 20.6 & 20.7
2. Assemble the trim with the (2) corner brackets provided.
Figure 20.2
3. Remove the 2 cast sides and slide the assembled trim
over the assembled surround set. Figure 19.3 on pg 19
Carefully slide surround and trim over the top of the insert
4.
into place matching the mounting holes on the panel with
the mounting holes on the insert. Secure with screws
provided. Figure 20.3
CAUTION
Logs are FRAGILE. Use extreme care when handling or
cleaning logs.
NOTICE:
Due to the abrasive nature of a pellet appliance fire, the
logs are not covered under warranty. Any placement variation other than shown here can cause excessive heat and
shall void the appliance warranty.
Back of Top Surround
Left Log
fire-parts.com
Screws
Log fits over screws
Back of Side Surround
Figure 20.4
Figure 20.1
Figure 20.2
bottom to fit over the screw
heads.
Figure 20.5
Right Log
Log rests in front of screws
Figure 20.6
Shown with trim installed on panel set
Figure 20.3
20
Figure 20.7
7082-131D
October 28, 2014
MT VERNON E2 INSERT
H. Remote Thermostat Installation
I. Power Cord
1.
1. Prior to installing the power cord, turn the dial control
“OFF”.
2. Make sure the wall receptacle has 120vac output.
NOTE: Using a circuit protector can protect the appliance circuits from power surges.
3. Remove the right side panel by releasing the upper,
spring-loaded latch. Access the latch through the upper
panel vent holes. The cast panel should fall forward.
Lift it out of its lower nest and set the panel aside. You
may need to disconnect the dial control wire harness.
4. Connect the power cord to the appliance first.
5. Route cord behind panel set.
When mounting the thermostat on the wall, be sure to
follow your remote thermostat’s installation instructions
carefully.
NOTE: The remote thermostat should be mounted
on an inside wall and not in direct line with the appliance convection air.
NOTE: If the remote thermostat is located too close
to the appliance, you may need to set the temperature setting slightly higher to maintain the desired
temperature in your home.
Photo of Thermostat separated from its docking station
below:
CAUTION
Shock Hazard
- Do not remove grounding prong from plug
- Plug directly into properly grounded & prong receptacle.
- Route cord away from appliance
- Do not route cord under or in front of appliance
fire-parts.com
Tools Needed:
Phillips screw driver
Power Drill
1/4” or 7/64” drill bit
Tape Measure
Detach the remote thermostat from its docking station by
pulling them directly away from each other.
Using the fasteners and (if needed) anchors – included
with the remote transmitter packaging – fasten the docking
station to the wall.
IMPORTANT NOTES:
For best appliance performance, position the docking
station at 60 inches height from the floor, no further than 20
feet from the appliance, out of direct sunlight, and out of the
direct flow of convection air coming from the appliance or
structure’s HVAC discharge air.
For instructions on thermostat function and interaction with
the appliance refer to the owner’s manual.
October 28, 2014
7082-131D
21
MT VERNON E2 INSERT
7
Mobile Home Installation
You must use a Quadra-Fire Outside Air Kit
for installation in a mobile home.
1.
2.
CAUTION
The appliance must be secured to the mobile home structure
by bolting it to the floor (using lag bolts). Use the same holes
that secured the appliance to the shipping pallet.
4.
The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC
approved grounding device.
6.
7.
8.
Do NOT cut through:
• Floor joist, wall, studs or ceiling trusses.
• Any supporting material that would affect the structural
integrity.
The combustion air duct system must be made of metal. It
must permit zero clearance to combustible construction and
prevent material from dropping into the inlet or into the area
beneath the dwelling and contain a rodent screen.
3.
5.
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED
An outside air inlet must be provided for the combustion air and
must remain clear of leaves, debris, ice and/or snow. It must
be unrestricted while the appliance is in use to prevent room
air starvation which causes smoke spillage. Smoke spillage
can also set off smoke alarms.
This unit is to be connected to a factory-built chimney
conforming to CAN/ULC-S629, Standard for 650°C Factory-Built Chimneys.
For removal of the chimney for mobile home transportation,
contact the proper transportation officials.
Spark Arrestor Cap
Refer to Clearances to Combustibles and floor protection
requirements on page 8 for listings to combustibles and
appropriate chimney systems.
fire-parts.com
Storm Collar
Roof Flashing
Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the
exterior of the structure.
Follow the chimney manufacturer’s instructions when installing
the vent system for use in a mobile home.
Joist Shield/Firestop
Installation shall be in accordance with the Manufacturers Home
& Safety Standard (HUD) CFR 3280, Part 24.
Approved Class L
or PL Pellet Vent
Part Number: OAK-3
Figure 22.1
WARNING
CAUTION
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
•
•
WARNING
It is critical to have a working smoke detector installed in
the home of unit operation.
•
Smoke alarms that are properly installed and maintained
play a vital role in reducing fire deaths and injuries. Having
a working smoke alarm reduces the chance of fire related
injuries..
Products of combustion generate carbon monoxide and
different fuels generate different levels. Carbon monoxide
Only use approved fuels in this appliance.
Always keep door shut during operation. Operating this unit
with doors open can allow CO to leak into the home.
CO can kill you before you are aware it is in your home. At
lower levels of exposure, CO causes mild effects that are often
mistaken for the flu. These symptoms include headaches,
dizziness, disorientation, nausea and fatigue. The effects of CO
exposure can vary greatly from person to person depending on
age, overall health and the concentration and length of exposure.
WARNING
NEVER INSTALL IN A SLEEPING ROOM.
22
7082-131D
October 28, 2014
MT VERNON E2 INSERT
8
Accessory List
R
Service Parts
MT VERNON INSERT-E2
Beginning Manufacturing Date: Dec 2014
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Accessories
Adjustable Hearth Support
ADJSPT-12
Y
Damper, 3 Inch - Tall Vertical Installs Only
PEL-DAMP3
Y
Damper, 4 Inch - Tall Vertical Installs Only
PEL-DAMP4
Firescreen
SCR-7005
Hearth Support
ZCSPT-MVI
Log Set (2 Pc)
Sold as set only
Outside Air Kit
LOGS-60-AE-B
Y
OAK-3
fire-parts.com
Top Vent Adapter
TPVNT-3
Vent Adapter, 3-4”
811-0720
Vent Adapter, 90, cleanout
TPVNT-6
Vent Adapter, Cleanout
811-0620
Surround, Std, Panel, For Cast Trim
SP-MTVS-CST
Component Pack
7036-041
Surround, Std, Panel, w/Gold Trim
SP-MTVS-GD
Component Pack
7036-042
Trim, Panel Set, Gold
250-4660
Surround, Std, Panel w/Nickel Black Trim
SP-MTVS-NB
Component Pack
7036-042
Trim Set, Black Nickel
7019-027
Trim Cast
Footer, Left
Footer, Right
Header
Trim Leg, Left
Trim Leg, Right
October 28, 2014
7082-131D
Matte Black
811-0930
Sienna Bronze
TR-CAST-CSB
Mahogany
811-0960
Matte Black
414-7090MBK
Sienna Bronze
414-7090CSB
Mahogany
414-7090PMH
Matte Black
414-7100MBK
Sienna Bronze
414-7100CSB
Mahogany
414-7100PMH
Matte Black
414-7110MBK
Sienna Bronze
414-7110CSB
Mahogany
414-7110PMH
Matte Black
414-7120MBK
Sienna Bronze
414-7120CSB
Mahogany
414-7120PMH
Matte Black
414-7130MBK
Sienna Bronze
414-7130CSB
Mahogany
414-7130PMH
23
CONTACT INFORMATION
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
log onto www.quadrafire.com
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating and • Read, understand and
follow these instrucmaintenance instructions for safe installations included.
tion and operation.
• Leave this manual with
D
DI O N
SC O
AR T
D
fire-parts.com
party responsible for use
and operation.
We recommend that you record the following pertinent
information for your heating appliance.
Date purchased/installed:
Serial Number:
Location on appliance:
Dealership purchased from:
Dealer phone:
Notes:
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645, 7047962
or other U.S. and foreign patents pending.
24
7082-131D
October 28, 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising