Arecont Vision MegaBall™ Installation Manual

Arecont Vision MegaBall™ Installation Manual
Arecont Vision MegaBall™ Installation Manual
0|P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall™ Wall Mount Version (-W) Installation Manual
Inside the box:
A.
B.
C.
D.
E.
F.
3.
Arecont Vision MegaBall™ camera with
wall mount (indoor use only)
CD with AV100 software and user
manuals (license key required for
recording)
Mounting template
Pack of three (3) wood screws and three
(3) dry wall anchors
One double-sided hex key (fixed focal lens
version only)
Security L-Key
Plug the Ethernet cable into the MegaBall™
PoE female RJ45 connector. (Image 2)
NOTE: If the camera will be powered via PoE,
please skip to step 5.
PoE RJ45
Digital In
Not included but needed:
•
Alarm Out or Audio Out
#1 Phillips head screwdriver
A
B
Auxiliary Power
C
Image 2
4.
D
E
F
If the camera will be powered by an AC 24V
or DC 12-48V power supply, connect external
power with pigtail cable connector.
NOTE 1: Ensure that the polarity of the DC
input on the camera matches the way that the
wires are installed in the connector shown in
Image 2.
Image 1
NOTE 2: AC power does not have polarity.
Mounting the Camera:
5.
1.
2.
Remove the camera and hardware from the
box.
Using the mounting template, prepare the
mounting surface for camera installation.
Align the holes on the camera wall mount with
the prepared holes on the mounting surface.
Attach the camera to the mounting surface
with the wood screws or any other hardware
suitable for the mounting surface.
1|P a g e
Arecont Vision MegaBall™ Installation Manual
Adjusting the Tilt, Pan, Z-Axis (yaw):
6.
To adjust the camera tilt, pan or z-axis (yaw),
loosen the ring on the wall mount bracket as
shown in Image 3 then adjust as necessary
and retighten the ring.
installation practices are not covered under
warranty!
Adjusting the Focus, Iris and Field of View:
7.
For the vari-focal model, adjust the focus, iris
and field of view using the provided Security
L-Key (Image 1F) as shown in Image 5.
Bracket Ring
Focus
Zoom
Iris
Image 3
NOTE : The 3-axis bracket allows 360°
camera body rotation, 90° tilt and 360°
bracket rotation for easy installation in any
location. (Image 4)
90°
360°
8.
Image 5
For the fixed-focal model, adjust the focus by
loosening the two set screws on the front shell
as shown in Image 6 using supplied double
sided hex key (Image 1E). Adjust the lens
adapter to focus the camera as shown in
Image 7. Retighten the set screws once
focusing is complete.
360°
Image 4
Set Screws
CAUTION: Adjusting the camera without
loosening the bracket ring may result in
scratches on the bracket joint. Incorrect
Image 6
Image 7
2|P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall™ Dome Version (-D) (-DA) Installation Manual
Inside the box:
Mounting the Camera:
A.
Arecont Vision MegaBall™ camera with inceiling mount (indoor use only)
B. Surface mount (preassembled on dome)
C. Audio Bezel (-DA module only)
D. O-ring (preassembled on bezel)
E. Dome cover (Bubble)
F. CD with AV100 software and user
manuals (license key required for
recording)
G. One double-sided hex key (fixed focal lens
version only)
H. Security L-Key
I. Pack of three (3) wood screws and three
(3) dry wall anchors
J. Mounting template
1.
2.
3.
Remove the camera and hardware from the
box.
Using the mounting template, prepare the
mounting surface for camera installation.
Plug Ethernet cable into the MegaBall™ PoE
female RJ45 connector. (Image 2)
NOTE: If the camera will be powered via PoE,
please skip to step 5.
PoE RJ45
Digital In
Not included but needed:
•
#1 Phillips head screwdriver
B
A
C
D
Alarm Out or Audio Out
E
Auxiliary Power
Image 2
4.
F
G
H
Image 1
I
J
If the camera will be powered by an AC 24V or
DC 12-48V power supply, connect auxiliary
power to terminal block on pigtail cable
connector.
NOTE 1: Ensure that the polarity of the DC
input on the camera matches the way that the
wires are installed in the connector shown in
Image 2.
NOTE 2: AC power does not have polarity.
3|P a g e
Arecont Vision MegaBall™ Installation Manual
5.
Using the provided Security L-key (Image
1F), loosen the three (3) screws securing the
dome cover (Image 3). Remove the vandal
resistant dome cover. NOTE: Do not remove
the screws from the dome cover.
In-ceiling Mount Installation (Optional)
7.
8.
9.
Image 3
6.
Loosen the three (3) machine screws (Image
4) and remove the in-ceiling mount camera
from the surface mount housing. (Image 4)
Using the mounting template, cut a hole in the
surface for mounting.
Insert the in-ceiling mount camera into the
hole.
Tighten the “lever screws” until the flush
mount is snug, as shown in Image 5. The
“Support Arm” will ride down the screw to
compress the mounting surface. NOTE: Do
not over-torque the lever screws.
Lever
Screw
Support
Arm
Image 5
Surface mount installation
Screws
10.
11.
Align the holes in the surface mount with the
prepared holes on the mounting surface with
the wood screws or any optional hardware
suitable for the mounting surface.
Attach the in-ceiling camera to the surface
mount, using the three machine screws as
shown on Image 4.
Image 4
4|P a g e
Arecont Vision MegaBall™ Installation Manual
Adjusting the Tilt, Pan, Z-Axis (Yaw):
Adjusting the Focus, Iris and Field of View:
12.
13.
To adjust the camera tilt, pan or z-axis (yaw),
loosen the 3 set screws on the in-ceiling
mount as shown in Image 6. Then adjust as
necessary and retighten the 3 set screws.
For the vari-focal model, adjust focus, iris and
field of view using the provided Security L-Key
(Image 1H on Page 3) as shown in Image 8.
Set Screw
Focus
Zoom
Iris
Image 6
NOTE : The 3-axis in-ceiling camera allows
360° camera body rotation, 90° tilt, and 360°
camera sleeve rotation for easy installation in
any location as shown in Image 7.
Camera Sleeve
°
Rotate 360
Tilt 90
Image 8
NOTE 1: Fully open the lens iris and close iris as
necessary to get better sharpness and depth of
field.
NOTE 2: Fully opening the lens iris under strong
light condition may result in less sharpness and
artificial color in Megaball™ WDR camera series as
shown in Image 9 and 10.
°
Camera Body
°
Rotate 360
Image 7
Image 9: Fully open lens iris
5|P a g e
Arecont Vision MegaBall™ Installation Manual
17.
Attach the provided dome cover (Image 1D
on Page 3) to the bezel as shown in Image
14.
Drift Pin
Image 10: Close lens iris as necessary
14.
For the fixed-focal model, adjust the focus by
loosening the two set screws on the front shell
as shown in Image 11 using the supplied
double sided hex key (Image 1G).
Image 11
Image 13
Image 12
Image 14
15.
Adjust the lens adapter to focus the camera
as shown in Image 12. Retighten the set
screws once focusing is complete.
18.
19.
Dome Cover (Bubble) Installation (Optional):
16.
Remove the protective film from the bubble.
NOTE: Take precaution not to scratch the
bubble.
Secure the dome cover to the camera using
the provided Security L-Key (Image 1H on
Page 3)
Remove the O-ring (Image 1D on Page 3)
from the bezel by pushing on the 4 drift pins
on the back of bezel shown in Image 13.
6|P a g e
Arecont Vision MegaBall™ Installation Manual
Audio Bezel Installation ( -DA models only):
20.
21.
23.
If adding dome cover (Image 1E) on the bezel
is necessary, follow Step 21-23 to replace
installed bezel with provided audio bezel
(Image 1C) and get best audio quality.
Remove O-ring (Image 1D), screws and
rubber cable from default bezel as shown in
Image 15.
Secure the dome cover to the camera using
the provided Security L-Key (Image 1H) as
shown in Image 17.
Default Bezel
O-ring
Image 17
Rubber
Cable
Note: If the dome cover is not required, keep using
default bezel and make sure the microphone hole is
not covered by the liner as shown on Image 18.
Image 15
22.
Install screws and dome bubble on the audio
bezel as shown in Image 16.
Microphone
hole
Image 18
Audio
Bezel
Image 16
7|P a g e
Arecont Vision MegaBall™ Installation Manual
Optional: Connecting Alarm I/O and Audio Out:
24.
To use the Alarm I/O, connect the alarm I/O to
the pigtail cable connector as shown in Image
2.
NOTE: Table 1 shows the electrical
characteristics and Table 2 shows cable color
for digital I/O.
Electrical
Characteristics:
Input voltage (V)
(measured between
+ and – terminals)
Output current (mA)
(measured between
+ and – terminals)
Applied Voltage
Rage: 0 - 80V
Min
Max
ON
2.9
6.3
OFF
0
1.3
ON
-
50
OFF
-
0.1
25.
Install the AV100 application manager
Software. (Image 19, found on the CD).
26.
Run the AV100 application manager by
double clicking on the icon shown below.
(Image 20, found on your desktop).
Camera
NOTE: you can download latest version
AV100 on website
http://www.arecontvision.com/softwares.php
IR & DN
Versions
DN
version
Only
Table 1
NOTE: Both the input and the output are electrically
isolated from the rest of the camera’s electrical
circuitry via general-purpose photo couplers. The
input is additionally protected with a serial 250 Ohm
resistor and a debouncing circuit. Duration of
any input signal should be at least 5ms to comply
with the requirements of the debouncing circuit.
Yellow
Red
Green
Black
Camera Installation:
Image 19
27.
Image 20
Select “Run” next to “Setup Cameras” from
the AV100 application manager as shown in
Image 21 and wait for “Arecont Vision
Camera Installer” window to appear as shown
in Image 22.
Digital IN +
Digital IN –
Digital OUT + / Audio Out +
Digital OUT - / Audio Out -
NOTE: The Audio Out will be only available for
Megaball Audio models (-A)
28.
Image 21
Click “Mode” tab to select desired install mode
on the Arecont Vision Camera Installer as
shown in Image 22.
Table 2
8|P a g e
Arecont Vision MegaBall™ Installation Manual
NOTE 1: Basic Mode: software will automatically
discover and change / assign IP address to match
PC subnet if they are not locked.
NOTE 2: Advanced Mode: software will
automatically discover but allow manual update of
the IP address. See “AV100 Installation Manual”
(found on the CD) for details on Advanced Mode.
NOTE : Double click the camera model on the
Camera Installer as shown in Image 22 to access
the camera web interface. See “AV Camera Web
Page User Manual” (found on the CD) for details on
the web interface.
NOTE3: User can verify camera model number and
FW version of all cameras as shown in Image 23.
Image 23
29.
Image 22
For basic mode, select “Install Cameras” on
the Arecont Vision Camera Installer as shown
in Image 22.
30.
Confirm that all the cameras connected to the
network switch appear in the upper window.
31.
Repeat Step 29 if all of the cameras do not
appear in the upper window.
32.
When all cameras are discovered and display
“Installed, online”, select “Save/Exit.” The
AV100 application main menu will appear.
33.
From the “AV100 Application Manager” menu,
select “Run” next to “Live video” to view live
images.
NOTE: See the “AV100 Installation Manual”
(found on CD) for details on camera
configurations.
CAUTION: If the software does not find a camera,
the software utility may be blocked by the anti-virus
®
or Windows firewall. Before turning them off,
please consult your IT manager.
9|P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall Accessories (Sold Separately)
Wall Mount (D4S-WMT-B or D4S-WMT) Installation Instructions
Inside the box:
A.
B.
C.
Wall mount ( Fits ¾” NPT Standard)
Pack of three (3) machine screws, four (4)
wood screws and four (4) dry wall anchors
Mounting template
NOTE: D4S-WMT-B color is black and D4SWMT color is light grey.
Image 25
Not included but needed:
•
5.
6.
#2 Phillips screw driver
7.
B
A
Run Ethernet cable through the wall mount
Attach wall mount to the wall using drywall
screws or any optional hardware suitable for
the mounting surface.
Connect Ethernet cable with Megaball pigtail
cable as shown on Image 25
C
Image 24
1.
Remove wall mount and hardware from the
box.
2.
Using the mounting template, prepare the
mounting provisions for camera installation.
3.
Attach surface mount (Image 1B on Page 3)
to wall mount as shown in Image 25 using
three machine screws provided.
Image 26
8.
For installation of the camera, please
reference “Mounting the Camera”.
10 | P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall Accessories (Sold Separately)
Pendant Mount (D4S-CMT-B or D4S-CMT) Installation Instructions
Inside the box:
A.
B.
C.
3.
Pendant Mount (Fits with ¾” NPT)
Pack of three (3) machine screws, three
(3) wood screws and three (3) dry wall
anchors
Mounting template
Attach surface mount (Image 1B on Page 3)
to pendant mount as shown in Image 28
using three machine screws provided.
NOTE: D4S-CMT-B color is black and D4SCMT color is light grey.
Not included but needed:
D.
#2 Phillips screw driver
4.
Image 28
Run Ethernet Cable through the Pendant
5.
Attach Pendant to the ceiling using the three
wood screws provided or any optional
hardware suitable for the mounting surface.
6.
Connect Ethernet cable with Megaball pigtail
cable as shown on Image 28
B
C
A
Image 27
1.
Remove pendant mount and hardware from
the box.
2.
Using the mounting template, prepare the
mounting provisions for camera installation.
Image 29
6.
For installation of the camera, please
reference “Mounting the Camera”.
11 | P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall Accessories (Sold Separately)
Junction Box Adapter (SV-JBA) Installation Instruction
Inside the box:
A.
B.
C.
D.
E.
Junction Box Adapter
Pack of four (4) machine screws
One double-sided hex key
Pack of four (4) wood screws and four (4)
dry wall anchors
Mounting template
Not included but needed:
•
•
•
Image 31
#2 Phillips screwdriver
Wall Mount, MD-WMT
¾” NPT Conduit (if necessary)
A
B
C
D
E
Conduit hole
Image 30
1.
2.
3.
Remove junction box adapter and hardware
from the box
Remove the conduit plug by first removing the
socket set screw using the provided hex key (C)
as shown on Image 31.
Attach the junction box adapter to the wall
using drywall screws or any optional hardware
suitable for the mounting surface.
4.
5.
6.
7.
Image 32
Attach the wall mount to junction box adapter
then attach cap to the wall mount as shown in
Image 32.
Connect ¾” NPT Conduit to the junction box
adapter.
Run Ethernet cable and outside power cable (if
necessary) through the Junction Box Adapter
and Wall Mount.
For installation of the camera, please reference
“Mounting the Camera.”
12 | P a g e
Arecont Vision MegaBall™ Installation Manual
MegaBall Accessories (Sold Separately)
Electrical Box Adapter (SV-EBA) Installation Instructions
Inside the box: (Accessory Sold Separately)
A.
B.
Electrical Box Adapter
Pack of four (4) machine screws
Image 34-1 Single gang box
A
D4S-WMT
Bracket holes
Image 34-2 Double gang box
Image 33
Not included but needed:
•
•
#2 Phillips head screwdriver
Common electrical box, such as single
gang box, double gang box, or square
electrical boxes shown in Image 34-1~4.
1.
Remove the electrical box adapter and
hardware from the box.
2.
Attach the wall mount bracket to the electrical
box adapter.
3.
Attach adapter to electrical box.
Image 34-3 Square box
Image 34-4 Square box
13 | P a g e
Arecont Vision MegaBall™ Installation Manual
R
1|P a g e
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising