fast fixing!
34
www.ramset.com.au
1300 780 063
Powder Actuated
Systems
With over 50 years of experience in designing
and manufacturing powder actuated tools and
consumables, Ramset™ Powder Actuated
fastening systems are innovative, powerful, easy
to use and specifically designed for Australian
applications. These tools provide a fast fixing
method for fastening many common building
materials to concrete, masonry and steel.
Tools in this range include:
• FrameMaster™ (TS750P)
• FormMaster™
• FrameBoss™
• TyMaster™
• Rocket
www.ramset.com.au
1300 780 063
35
Powder Actuated
Systems
36
www.ramset.com.au
1300 780 063
Contents
Powder Actuated Systems
Fastening Principles 38
Selection Guide 40
FrameBoss™42
Rocket46
FrameMaster™ (TS750P)48
FormMaster™50
TyMaster™52
Drive Pins & Power Loads
www.ramset.com.au
56
1300 780 063
37
Fastening Principles
Powder Actuated Systems
Powder Actuated Technology - How it works
Fastening Principles
Ramset™ Powder Actuated Technology uses a captive piston to transfer the
energy from the power load to the fastener. In this way the majority of any
excess energy, which is produced by the power load, is absorbed within the
tool by the buffer.
Ramset™ Powder Actuated tools are powerful and reliable which allows them
to fasten to steel, concrete and masonry year after year.
5
4
3
1. Firing Pin
2. Power Load
3. Captive Piston
4. Buffer
5. Powder Actuated Fastener
How to select a Ramset™ Drive Pin to directly fasten an object to CONCRETE
Fixing to concrete
As the fixing enters the concrete, extreme pressure and heat are created.
This creates a bond that provides high loading strength in concrete.
Edge distance
Do not fix closer than 75mm from the edge of concrete. If the concrete
cracks, the fixing may not hold.
M
Recommended minimum fixing spacing
Setting fixings too close together can cause the concrete to crack. The
recommended minimum distance between fixings is 75mm. Never attempt a
fixing application too close to another fixing as this could affect the previously
inserted fixing’s embedment.
Concrete thickness
It is important that the concrete be at least three times as thick as the fixing
penetration. If the concrete is too thin, the compressive forces forming at the
fixing’s point can cause the free face of the concrete to break away.
This creates a dangerous condition from flying concrete and / or the fixing
and also results in a reduction of fastener holding power.
Minimum Shank Length
Thickness +
of material
(M)
25mm
How to select a Ramset™ Drive Pin to directly fasten an object to STEEL
Fixing to steel
The resilience of steel provides a clamping effect to the fixing. This
combined with the tremendous heat that is created, provides a welding and
clamping effect to give maximum holding power.
M
Edge distance
The recommended edge distance for a fixing to the edge of steel is 13mm.
Never fire the tool within 13mm of the edge of a steel base material because
the steel may bend or break off, allowing the fixing to ricochet.
T
Recommended minimum fastener spacing
The recommended minimum distance between fixings is 25mm. Never
attempt a fixing application too close to another fixing as this could affect the
previously installed fixing’s embedment.
Steel thickness
Do not fasten into steel base material thinner than the fastener shank
diameter. Holding power may be reduced and the fastener may be
overdriven.
As a guide when:
• Fixing into steel - min. steel thickness = 4mm
38
www.ramset.com.au
1300 780 063
Minimum Shank Length
Thickness +
of material
(M)
Steel
Thickness
(T)
+
6mm
point
allowance
2
1
Notes
Powder Actuated Systems
www.ramset.com.au
1300 780 063
39
Selection Guide
Powder Actuated Systems
40
25 to
25 to
100mm 75mm
Timber Formwork Pins
For Concrete & Easy
Pin Removal
56
60 to
60 to
100mm 75mm
Premium Drive Pins
For Structural Steel
57
25 to
75mm
Washered Drive Pins
For Concrete , Masonry
& Steel
57
25 to
75mm
4
4
4
4
4
4
4
25 to
50mm
4
25 to
75mm
4
4
4
(TS750P)
4
60 to
60 to
75mm 100mm
▲
25 to
75mm
●
4
4
4
4
25 to
75mm
4
▲
60 to
75mm
▲
25 to
75mm
●
4
25 to
75mm
JobMaster™
FrameMaster™
4
25 to
25 to
25 to
75mm 100mm 32mm
▲
4
25 to
75mm
TyMaster™
56
FormMaster™
Standard Drive Pins
For Concrete, Masonry
& Steel
Rocket
(FrameBoss)
FrameBoss™
(FrameBoss75)
Product Range
FrameBoss™
42 4246 4850 52 54
Page Reference
Powder Actuated Systems
4 Recommended
● Maybe possible dependant on substrate
▲ Not suitable
4
4
25 to
32mm
25 to
75mm
25 to
75mm
25 to
32mm
25 to
75mm
▲
▲
▲
▲
▲
Standard Collated Drive
Pins For Concrete,
44
Masonry & Steel
25 to
75mm
Premium Collated Drive
Pins For Concrete,
44
Masonry & Steel
25 to
75mm
25 to
60mm
▲
▲
▲
▲
▲
4
4
4
25 to
60mm
4
Angle Bracket &
Threaded Rod Hanger
Assemblies
58
4
4
4
4
▲
4
4
Drive Pins For Fixing
Thin Steel To Steel
58
4
4
4
4
4
4
4
Drive Pins For Fixing
Thin Steel To Steel
58
4
4
▲
●
4
▲
●
Insulation Fasteners
For Concrete, Masonry
& Steel
45
▲
With
Adaptor
▲
▲
▲
▲
▲
Soft Washered
Membrane Fastener
59
4
4
▲
4
4
▲
4
www.ramset.com.au
4
1300 780 063
Selection Guide
Powder Actuated Systems
Fastener Selection and Correct Setting
The correct selection and setting of Powder Actuated Fasteners is critical
with all tools to ensure a secure fixing and long tool life.
The correct setting of the fastener should be as detailed in the diagrams to
avoid excessive overdrive and a secure fix.­
PIN
Part No.
PIN
Part No.
LWU75
SP12
LDU75
SP12
Powder Actuated Systems
Where possible, a washer (Part No: RCD16F) or a washered fastener
should be used. (Application permitting, to reduce overdrive and
produce maximum clamping force). Repeated excessive overdrive
will result in damage and short life of tool parts.
RDU99
SC925 SC930C SC930C
SC925C SC930 SC930 SC950C SC960C
PIN
Part No.
LWU75
LDU75
RDU99
Powerload Selection Guide - Concrete
Tool
FrameBoss™
FrameMaster™ TS750P
FormMaster™
JobMaster™
TyMaster™
Rocket
20 MPa Concrete
Low Strength
PLSGR22
PLSGR22
PLSGR22
PLCGR22S
PLSGR22
PLSGR22
30 MPa Concrete
Medium Strength
PLSYW22
PLSYW22 PLSYW22 PLCYW22S PLSYW22 PLSYW22 40 MPa Concrete
High Strength
PLSRD22
PLSRD22
PLSRD22
PLCRD22S
PLSRD22
PLSYW22
This chart is to be used as a guide only.
Ramset™ recommends to always start a new application with the minimum powerload strength, and if applicable, the tool at minimum power setting, then gradually increase power with load strengths,
and if applicable, a combination of power adjustment setting powerload and pin length.
PIN
Part No.
SP12
SP12
SC925 SC930C SC930C
SC925C SC930 SC930 SC950C SC960C
www.ramset.com.au
1300 780 063
41
FrameBoss™
Fully Automatic Tool
Powder Actuated Systems
Quick change
fastener guide
Power adjustment
Automatic
piston return
NEMW
agazine
Cushioned
rubber grip
75mm odel
M
le
Availab
10 pin magazine
FAST FIXING!
75mm or 100mm single shot
fastener guide included in tool kit,
dependent on tool model
60mm
Magazine
Model
Description
The Ramset™ FrameBossTM is a fully automatic powder actuated tool, which
is capable of fixing 10 pins without the need to reload or cycle the tool. The
automatic piston return system and 10 pin magazine allow for faster fixing
rates with less effort. The magazine can be adjusted to lock into a number of
positions to allow the tool to be used in confined spaces. The FrameBossTM
tool is also supplied with a single shot fastener guide to allow the tool to be
used with longer fasteners and assembles such as brackets and clips. With a
huge 380 Joules of impact energy coupled with power adjustment, the tool can
be used in a wide variety of applications e.g. Timber framing, formwork and
the fixing of steel track. FrameBossTM is designed to save you time and money.
Specification
Model
Weight
Impact Force
Fixing Capacity:
Timber to Concrete
Timber to Steel
Metal to Concrete
Metal to Steel
Pin Capacity
(Single shot)
Pin Capacity
(Magazine)
Overall Length
Substrates
FrameBoss
3.0 kg (3.2 kg with mag.)
380J
FrameBoss75
3.7 kg (3.99 kg with mag.)
380J
50mm
50mm
3mm
3mm
up to 75mm
75mm
50mm
3mm
3mm
up to 100mm
up to 60mm
up to 75mm
490mm
525mm
Concrete, Steel, Masonary Concrete, Steel, Masonary
Related Products
Power Loads
Drive Pins
42
Tool Accessories
Drive Pin Accessories
www.ramset.com.au
1300 780 063
Features & Benefits
• Automatic piston return
• No manual cycling required
• Easy to maintain on site
• 10 Pin magazine and single shot fastener guide
• 75mm single shot capacity, 100mm with FRAMEBOSS 75
• 60mm magazine capacity, 75mm with FRAMEBOSS 75
• 380J maximum impact energy
• Power adjustment
• Trigger lock
• Hand guard
• Cushioned rubber grip
FrameBoss™
Fully Automatic Tool
Trades & Applications
Powder Actuated Systems
Residential Home
Formwork
Ceiling & Partitioning
Bricklayer
Builder
Contractor
Contractor
Timber to concrete
4
4
Timber to steel
4
4
Sacrificial steel formwork to steel
4
Steel track to concrete & steel
4 4
Brick Ties to concrete & steel
4 4
Standard Operating Procedure
Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain
personal instruction and training from a Ramset™ representative.
1.First cycle the tool and insert the power load strip.
2.Insert the correct fastener or collated fasteners, (without compressing the front of the tool).
3.The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).
4.Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.
FrameBoss™
Part No
FrameBoss
FrameBoss75
Description
FrameBoss™ tool kit 60 mm Magazine
FrameBoss™ tool kit 75 mm Magazine
Order Qty
1
1
Kit includes: FrameBoss™ tool, steel tool case, single shot fastener guide, magazine, safety glasses,
maintenance kit and instruction manual.
FrameBoss Accessories
Part No
PA37037
010982
010983
PA37040
PA37038
PA9316
PBT
PA1613
PA37023
PAWS8
Description
Piston
Piston Return Spring (x2)
Piston Buffer (x2)
Fastener Guide Assembly
Magazine Assembly
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Spall Shield
Explosive Tool in Use - Safety Warning Sign
FrameBoss75 Accessories
Order Qty
1
1
1
1
1
1
1
1
1
1
Part No
PA37041
011483
010983
PA37063
PA37049
PA9316
PBT
PA1613
PA37023
PAWS8
Description
Piston
Piston Return Spring (x1)
Piston Buffer (x2)
Fastener Guide Assembly
Magazine Assembly
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Spall Shield
Explosive Tool in Use - Safety Warning Sign
Order Qty
1
1
1
1
1
1
1
1
1
1
Power Load Strips
Part No
PLSGR22
PLSYW22
PLSRD22
Colour
Green
Yellow
Red
Strength
Weak
Medium
Strong
Order Qty
100
100
100
www.ramset.com.au
1300 780 063
43
FrameBoss™
Collated Drive Pins
Standard Collated Drive Pins for Fixing to
Concrete and Masonary
Powder Actuated Systems
Collated Drive Pins designed for use with the FrameBoss™ magazine for
fastening to standard strength concrete, masonry and steel up to a maximum
of 8mm.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel (Plastic Collation)
Zinc Electroplated (Minimum coating 7µm)
8.8mm
3.7mm
1120N/mm2
1800N/mm2
50 -55HRC
Part No
Drive Pin Length
C925C
C930C
C940C
C950C
C960C
C975C
25mm
30mm
40mm
50mm
60mm
75mm
Max Fixture
(thickness to steel)
12mm
18mm
30mm
35mm
45mm
60mm
Max Fixture
(thickness to concrete)
2mm
5mm
15mm
25mm
35mm
50mm
Order Qty
500
500
300
300
300
300
Collated Pins for Fixing to Structural Steel
and Hard Concrete
The Ramset™ range of Premium Collated Drive Pins is designed for use with
the FrameBoss™ magazine for fastening to steel and hard concrete applications. The design of these drive pins allows them to penetrate hard materials
with less power while the strengthened shank greatly reduces the possibility
of column collapse.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel (Plastic Collation)
Zinc Electroplated (Minimum coating 7µm)
8.8mm
4.0mm / 3.7mm
1240N/mm2
2000N/mm2
54 -58HRC
Part No
Drive Pin Length
SC925C
SC930C
SC940C
SC950C
SC960C
25mm
30mm
40mm
50mm
60mm
Max Fixture
(thickness to steel)
12mm
18mm
30mm
35mm
45mm
Max Fixture
(thickness to concrete)
2mm
5mm
15mm
25mm
35mm
*Refer to page 56 for more fasteners that are
suitable for use with the FrameBossTM Tool
Ramset™ recommends application test on-site before commencing use.
44
www.ramset.com.au
1300 780 063
Order Qty
500
500
300
300
300
FrameBoss™
InsulFastTM Accessory Kit
Description
The Ramset™ InsulFast™ adaptor kit transforms the FrameBoss™ tool into a specialist insulation fixing tool with automatic piston return.
The FrameBoss™ tool in this configuration is capable of fastening insulation from 40mm to 120mm without compression.
(This adaptor is not compatible with the FRAMEBOSS75 model tool)
Accessories
Part No
PA11030
011031
011032
Description
InsulFast™ adaptor kit includes Fastener Guide Assembly, Piston and Piston Return Spring
Piston - includes Piston Return Spring
Piston Return Spring x 2
Fastener Specification
Fastener Body Material
Holding Diameter
Lengths Available
Drive Pin Material
Drive Pin Plating
Drive Pin Shear Strength (Ultimate)
Technical Load Data
Part No.
CI960
CI670
CI6100
CI6120*
Concrete Strength
25 – 45 MPa
25 – 45 MPa
25 – 45 MPa
25 – 45 MPa
Order Qty
1
1
1
Powder Actuated Systems
NEW
High Density Polyethylene (HDPE)
60 mm (90 mm for CI960)
50 mm to 120 mm
Carbon Steel
Electroplated Zinc
12.0 kN
Tensile Working Load Limit WLL
0.30 kN
0.30 kN
0.30 kN
0.30 kN
The recommended loads (kN) are calculated from the mean ultimate load
and a factor of safety higher than 4.
A minimum of 4 fixings per fastened unit are required.
* Available upon request.
Insulation Fasteners for Concrete, Masonary and Steel
Part No.
CI960
CI670
CI6100
CI6120*
Rigid Insulation
Thickness
60mm
70mm
100mm
120mm
Soft Insulation
Thickness
60 mm – 65mm
70 mm – 75mm
100mm – 110mm
120mm – 130mm
FastenerOrder
Colour
Qty
Black
100
Natural (White)
200
Natural (White)
100
Natural (White)
100
* Available upon request.
Ramset™ recommends application test on-site before commencing use.
www.ramset.com.au
1300 780 063
45
Rocket
Automatic Short Pin Tool
Power adjustment
Powder Actuated Systems
Automatic
piston return
Cushioned
rubber grip
Description
The Ramset™ Rocket is the fastest high volume, short pin tool. This
powerful fully automatic tool performs high volume repetitive short pin
fixings with ease.
Specifications
Weight
Impact Force
Fixing Capacity:
Timber to Concrete
Timber to Steel
Metal to Concrete
Metal to Steel
Pin Capacity
Overall Length
Substrates
2.2kg
360J
25mm
35mm
3mm
3mm
up to 50mm
435mm
Concrete, Steel, Masonary
Features & Benefits
•Fast - 10 shot strip feed with automatic advance
•Optimum fixing - power adjustment ensures consistent performance
•Power - adjustable for use with steel or concrete
•Lightweight - minimal operator fatigue
•Minimal maintenance
Related Products
Power Loads
Drive Pins
Tool Accessories
Drive Pin Accessories
46
www.ramset.com.au
*Refer to page 56 for fasteners that are
suitable for use with the Rocket Tool
1300 780 063
Rocket
Automatic Short Pin Tool
Trades & Applications
Residential Home
Ceiling & Partitioning
Builder
Contractor
Steel framing to concrete
4
Steel track to concrete & steel
4
Brick Ties to concrete & steel
Bricklayer
4
Powder Actuated Systems
Standard Operating Procedure
Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain
personal instruction and training from a Ramset™ representative.
1.First insert the power load strip.
2.Insert the correct fastener, (without compressing the front of the tool).
3.The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).
4.Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.
Rocket
Part No
ROCKET
Description
Rocket Tool
Order Qty
1
Kit includes: Rocket tool, high impact carry case, safety glasses, maintenance kit and instruction
manual.
Rocket Accessories
Part No
A1010
A1049A
A1130A
PA9316
PBT
PA1613
PAWS8
Description
Piston
Fastener Guide Assembly
Buffer Assembly
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Explosive Tool in Use - Safety Warning Sign
Order Qty
1
1
1
1
1
1
1
Power Load Strips
Part No
PLSGR22
PLSYW22
PLSRD22
Colour
Green
Yellow
Red
Strength
Weak
Medium
Strong
Order Qty
100
100
100
www.ramset.com.au
1300 780 063
47
FrameMaster™
TS750P - Power Adjustable Tool
Powder Actuated Systems
Power adjustment
Cushioned
rubber grip
Description
The Ramset™ FrameMaster™ TS750P is the timber framing expert. A power
adjustable tool designed for fixing timber framing to concrete and general
repetitive work.
Specifications
Weight
Impact Force
Fixing Capacity:
Timber to Concrete
Timber to Steel
Metal to Concrete
Metal to Steel
Pin Capacity
Overall Length
Substrates
2.5kg
300J
60mm
50mm
3mm
3mm
up to 85mm
380mm
Concrete, Steel, Masonary
Features & Benefits
•Fast – 10 shot strip feed with automatic advance
•Optimum fixing – positive power adjustment ensures
consistent performance
•Power – adjustable for use with steel or concrete
•Minimal maintenance – easy to dismantle & clean to reduce downtime
•Long Life – long life piston & buffer
Related Products
Power Loads
Drive Pins
Tool Accessories
Drive Pin Accessories
48
www.ramset.com.au
*Refer to page 56 for fasteners that
are suitable for use with the
FrameMasterTM TS750P Tool
1300 780 063
FrameMaster™
TS750P - Power Adjustable Tool
Trades & Applications
Residential Home
Formwork
Bricklayer
Builder
Contractor
4
4
4
4
4
4
Timber to concrete
Timber to steel
Brick Ties to concrete & steel
Powder Actuated Systems
Standard Operating Procedure
Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain
personal instruction and training from a Ramset™ representative.
1.First cycle the tool and insert the power load strip.
2.Insert the correct fastener, (without compressing the front of the tool).
3.The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).
4.Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.
FrameMaster™ TS750P
Part No
TS750P
Description
FrameMaster™ TS750P tool
Order Qty
1
Kit includes: FrameMaster™ tool, high impact carry case, safety glasses, maintenance kit and
instruction manual.
FrameMaster™ TS750P Accessories
Part No
PA27833
PA27432
PA27831
PA9316
PBT
PA1613
PA27580
PAWS8
Description
Piston Assembly - Standard
Piston Assembly - High Power
Fastener Guide Assembly
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Spall Shield
Explosive Tool in Use - Safety Warning Sign
Order Qty
1
1
1
1
1
1
1
1
Power Load Strips
Part No
PLSGR22
PLSYW22
PLSRD22
Colour
Green
Yellow
Red
Strength
Weak
Medium
Strong
Order Qty
100
100
100
www.ramset.com.au
1300 780 063
49
FormMaster™
The Formworker’s Tool
Powder Actuated Systems
Power adjustment
Cushioned
rubber grip
HIGH POWER!
Description
The Ramset™ FormMaster™ is the professional’s choice for long pin fixing.
A high powered fastening system with the power and comfort to meet the
demands of the timber and steel formwork industry and heavier repetitive
fixing jobs.
Specifications
Weight
Impact Force
Fixing Capacity:
Timber to Concrete
Timber to Steel
Metal to Concrete
Metal to Steel
Pin Capacity
Overall Length
Substrates
3.0kg
400J
75mm
50mm
3mm
3mm
up to 100mm
448mm
Concrete, Steel, Masonary
Features & Benefits
•Fast – 10 shot strip feed with automatic advance
•Optimum fixing – positive power adjustment ensures
consistent performance
•Power – adjustable for use with steel or concrete
•Front barrel safety grip & hand guard – all day use comfort
•Minimal maintenance – easy to dismantle & clean to reduce downtime
•Long Life – long life piston & buffer
Related Products
Power Loads
Drive Pins
Tool Accessories
Drive Pin Accessories
50
www.ramset.com.au
*Refer to page 56 for fasteners that
are suitable for use with the
FormMasterTM Tool
1300 780 063
FormMaster™
The Formworker’s Tool
Trades & Applications
Standard Operating Procedure
Powder Actuated Systems
Residential Home
Formwork
Bricklayer
Builder
Contractor
Timber to concrete
4
4
Timber to steel
4
4
Brick Ties to concrete & steel
4
4
Sacrificial steel formwork to steel
4
Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain
personal instruction and training from a Ramset™ representative.
1.First cycle the tool and insert the power load strip.
2.Insert the correct fastener, (without compressing the front of the tool).
3.The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).
4.Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.
FormMaster™
Part No
Description
FORMMASTER FormMaster™ Tool
Order Qty
1
Kit includes: FormMaster™ tool, high impact carry case, safety glasses, maintenance kit and
instruction manual.
FormMaster™ Accessories
Part No
PA28811
PA312860
PA28816
PA9316
PBT
PA1613
PA310000
PAWS8
Description
Piston Assembly
Buffer x 5
Fastener Guide Assembly
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Spall Shield
Explosive Tool in Use - Safety Warning Sign
Order Qty
1
1
1
1
1
1
1
1
Power Load Strips
Part No
PLSGR22
PLSYW22
PLSRD22
Colour
Green
Yellow
Red
Strength
Weak
Medium
Strong
Order Qty
100
100
100
www.ramset.com.au
1300 780 063
51
TyMaster™
The Overhead Tool
Powder Actuated Systems
Automatic
piston return
Dedicated
pole tool
Automatic
charge advance
OVERHEAD FIXING!
Description
The Ramset™ TyMaster™ is an effortless, overhead fixing, fully automatic tool
with extension pole for efficient, remote, overhead fixing of suspended ceilings
and services installations.
Typical Properties
Weight
Impact Force
Fixing Capacity:
Metal to Concrete
Metal to Steel
Pin Capacity
Overall Length (including pole)
Substrates
2.3kg
320J
3mm
3mm
up to 32mm
2000mm
Concrete, Steel, Masonary
Features & Benefits
•Fast 10 shot strip feed with automatic advance
•Lightweight – reduced fatigue in overhead operation
•Fully automatic – high install rate
•Safe – patented “Breech lockout” prevents the tool from firing while directed
horizontally or while directed below the horizontal
•Minimal maintenance
Related Products
Power Loads
Drive Pins
Tool Accessories
Drive Pin Accessories
52
www.ramset.com.au
*Refer to page 56 for fasteners that
are suitable for use with the
TyMasterTM Tool
1300 780 063
TyMaster™
The Overhead Tool
Trades & Applications
Ceiling & Partitioning
Contractor
Fixing of suspended ceilings
4
Light duty cable tray
Catenary wire fixings
Electrical
Contractor
4
4
Powder Actuated Systems
Standard Operating Procedure
Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain
personal instruction and training from a Ramset™ representative.
1.First insert the power load strip in the tool.
2.Load the correct drive pin, (without compressing the front of the tool).
3.Carefully raise the tool to the ceiling and depress the barrel assembly where the fastening is to be made.
4.While holding the tool perpendicular and compressed against the work surface, forcibly push upwards on the pole handle to fire the tool.
TyMaster™
Part No
TYMASTER
Description
TyMaster™ Tool
Order Qty
1
Kit includes: TyMaster™ tool, high impact carry case, 1560mm (3 x 520mm) pole extension,
safety glasses, maintenance kit and instruction manual.
TyMaster™ Accessories
Part No
653116
PAT1085
653021
653106
653035
PA9316
PBT
PA1613
PAWS8
Description
Piston Standard
Piston High Power
Buffer x 3
Fastener Guide Assembly
Spall Shield
PA Lubricating and Release Oil
Drive Pin Removal Tool
Safety Glasses
Explosive Tool in Use - Safety Warning Sign
Order Qty
1
1
1
1
1
1
1
1
1
Power Load Strips
Part No
PLSGR22
PLSYW22
PLSRD22
Colour
Green
Yellow
Red
Strength
Weak
Medium
Strong
Order Qty
100
100
100
www.ramset.com.au
1300 780 063
53
Drive Pins
Powder Actuated Systems
Standard Drive Pins for Concrete, Masonry
and Steel
Powder Actuated Systems
Drive Pins designed for fastening to standard strength concrete, masonry and
steel up to a maximum of 8mm.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel
Zinc Mechanically Plated (Min coating 6µm)
7.8mm
3.7mm
1200N/mm2
1950N/mm2
52 - 55HRC
Part No
Drive Pin Length
LDU25
LDU32
LDU38
LDU42
LDU50
LDU57
LDU65
LDU75
LDU90
LDU99
25mm
32mm
38mm
42mm
50mm
57mm
65mm
75mm
90mm
100mm
Max Fixture
(thickness to steel)
12mm
20mm
25mm
30mm
35mm
45mm
50mm
N/A
N/A
N/A
Max Fixture
(thickness to concrete)
2mm*
7mm
12mm
20mm
25mm
35mm
45mm
50mm
65mm
75mm
Order Qty
100
100
100
100
100
100
100
100
100
100
* Denotes steel fixture only
Timber Formwork Pins for Concrete and
Easy Pin Removal
Drive Pins designed for fastening timber formwork to concrete. When the
timber needs to be removed, the small head reduces the force required to
strip the timber. The groove in the shank allows the pin to be removed easily
with Ramset’s drive pin breaker tool.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
PBT
(Pin Breaker Tool)
Carbon Steel
Zinc Mechanically Plated (Min coating 6µm)
6.3mm
3.7mm
1200N/mm2
1950N/mm2
52 - 55HRC
Part No
LDU60F
LDU75F
LDU99F
PBT (Pin Breaker Tool)
Drive Pin Length
60mm
75mm
100mm
Max Timber Thickness
35mm
50mm
75mm
Ramset™ recommends application test on-site before commencing use.
56
www.ramset.com.au
1300 780 063
Order Qty
200
200
200
1
Drive Pins
Powder Actuated Systems
Premium Drive Pins for Structural Steel
Ramset’s range of Premium Drive Pins has been designed for steel and hard
concrete applications. The design of these drive pins allows them to penetrate hard materials with less power while the strengthened shank greatly
reduces the possibility of column collapse.
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel
Zinc Electroplated (Min coating 7µm)
8.8mm
4.0 / 3.5mm
1240N/mm2
2000N/mm2
54 - 58HRC
Part No
Description
SC925
SC930
SC940
SC950
SC950W
SC960
SC960W
SC970
Thin Steel to Structural Steel Pin
Timber to Structural Steel Pin
Timber to Structural Steel Pin
Timber to Structural Steel Pin
Frame & Truss 16mm Washered Pin
Timber to Structural Steel Pin
Frame & Truss 16mm Washered Pin
Timber to Structural Steel Pin
Max Fixture
(thickness to steel)
12mm
18mm
30mm
35mm
35mm
45mm
45mm
55mm
Max Fixture
(thickness to concrete)
2mm
5mm
15mm
25mm
25mm
35mm
35mm
45mm
Order Qty
100
100
100
100
100
100
100
100
Powder Actuated Systems
Specifications
Washered Drive Pins For Concrete, Masonry
and Steel
Washered Drive Pins designed to provide maximum clamping load while
improving tool piston life. Wherever possible the use of washered drive pins
is recommended to prevent failure of the material being fastened.
LWU25K
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel
Zinc Mechanically Plated (Min coating 6µm)
7.8mm
3.7mm
1200N/mm2
1950N/mm2
52 - 55HRC
LWU25
Part No
Washer Diameter
Drive Pin Length
LWU25
LWU32
LWU75
LWU25K
22mm
22mm
16mm
16mm
25mm
32mm
75mm
25mm
Max Fixture
(thickness to concrete)
2mm*
7mm
50mm
2mm*
Order Qty
100
100
100
100
* Denotes steel fixture only
Ramset™ recommends application test on-site before commencing use.
www.ramset.com.au
1300 780 063
57
Drive Pins
Powder Actuated Systems
Angle Bracket and Threaded Rod Hanger
Assemblies
LAU25
Powder Actuated Systems
Ramset’s Angle Bracket and Threaded Rod Hanger Assemblies provide a
secure fixing point for a wide variety of applications.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Part No
LAU25
LAU30H
LZU30H
LZU30H
Carbon Steel
Zinc Plated
7.8mm
Various
Description
Standard Duty
Heavy Duty
Threaded Rod Hanger - M10
Drive Pin Length
25mm
25mm
25mm
Order Qty
100
100
100
Drive Pins For Fixing Thin Steel To Steel
Drive pin for fixing thin steel to structural steel sections.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel
Zinc Mechanically Plated (Min coating 6µm)
7.8mm
4.0mm
1200N/mm2
1950N/mm2
52 - 55HRC
Part No
SP12
Description
Premium Steel Pin
Drive Pin Length
13mm
Order Qty
100
Washered Drive Pins For Fixing Thin Steel
To Steel
Drive Pin designed for fixing thin steel to structural steel sections. This drive
pin provides excellent clamping with a special 14mm diameter washer that
interacts with a tapered section on the shank of the drive pin.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Part No
SBR9
Carbon Steel
Zinc Electroplated (Min coating 7µm)
8.8mm
4.0mm
1240N/mm2
2000N/mm2
54 - 58HRC
Description
Decking Pin
Washer Diameter
14mm
Drive Pin Length
20mm
* Suitable for use with Kingflor®, Bondek®, Condeck®
Ramset™ recommends application test on-site before commencing use.
58
www.ramset.com.au
1300 780 063
Order Qty
100
Drive Pins
Powder Actuated Systems
Soft Washered Membrane Fastener
Soft Washered Drive Pin designed for fastening insulation up to 25mm, also
designed for fastening foils and membranes such as drainage sheeting to
concrete. The soft washer prevents any damage to the foil or membrane.
Specifications
Powder Actuated Systems
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Washer Diameter
Carbon Steel (Plastic Washer)
Zinc Electroplated (Min coating 7µm)
8.8mm
3.7mm
1120N/mm2
1800N/mm2
50 - 55HRC
35mm
Part No
Drive Pin Length
CR950P
50mm
Max Insulation
Thickness
25mm
Order Qty
200
Drive Pin Accessories
Drive Pin accessories for use with Ramset’s standard LDU range of Standard
Drive Pins for concrete, masonry and steel. The use of the discs provides
maximum clamping loads while improving tool piston life. The use of the
angle clip provides a fixing point for applications such as catenary wire.
Specifications
Raw Material
Corrosion Protection
Low Carbon Steel
Zinc Electroplated (Min coating 6µm)
RCD16F
Part No
RCA25F
RCD16F
RCD22F
Description
25mm Angle Clip
16mm Disc
22mm Disc
RCD22F
RCA25F
Order Qty
100
100
100
Ramset™ recommends application test on-site before commencing use.
www.ramset.com.au
1300 780 063
59
Misc. Drive Pins
Powder Actuated Systems
Collated Drive Pins to suit Hilti™, DX 351, DX
460, DX A40, DX A41 Magazine Tools
Powder Actuated Systems
Collated Drive Pins designed for use with Hilti tools; DX460, DX351,
DX-A40/41 fitted with a magazine.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Part No
RHC22
RHC27
­RHC52
RHC62
RHC72
Carbon Steel
Zinc Mechanically Plated (Min coating 7µm)
8.2mm
3.7mm
1200N/mm2
1950N/mm2
52 - 55HRC
Nominal
Head Diameter
8.2mm
8.2mm
8.2mm
8.2mm
8.2mm
Length
22mm
27mm
52mm
62mm
72mm
Max Fixture
(Thickness to steel)
10mm
14mm
37mm
47mm
62mm
Max Fixture
(Thickness to Concrete)
1mm
3mm
27mm
42mm
47mm
Order Qty
100
100
100
100
100
Drive Pins to suit Previous Ramset™ Tools J20S, J20, 1/4” Barrel
Drive Pins for use with previous Ramset™ direct acting powder actuated
tools; J20, J20S fitted with a ¼” barrel.
Specifications
Raw Material
Corrosion Protection
Nominal Head Diameter
Nominal Shank Diameter
Shear Strength
Tensile Strength
Hardness
Carbon Steel
Zinc Mechanically Plated (Min coating 6µm)
6.3mm
3.7mm
1200N/mm2
1950N/mm2
52 - 55HRC
Part No
HDB50
HDB64
HDB75
HDB95
Nominal Head Diameter
6.3mm
6.3mm
6.3mm
6.3mm
Length
50mm
64mm
75mm
95mm
Ramset™ recommends application test on-site before commencing use.
60
www.ramset.com.au
1300 780 063
Order Qty
100
100
100
100
Power Loads
Powder Actuated Systems
Powerloads to suit Previous Ramset™ Tools
- J20S, J20, 1/4” Barrel
Power Load Cartridge designed for use with Ramset’s JobMaster™ tool and
previous Ramset™ direct acting powder actuated tools; J20, J20S.
Charge Type
Calibre
Part No
PLCGR22S
PLCYW22S
PLCRD22S
*PLCPU22S
Single Cartridge
5.6 x 16mm
Calibre
5.6mm x 16mm
5.6mm x 16mm
5.6mm x 16mm
5.6mm x 16mm
Colour
Green
Yellow
Red
Purple
Strength
Weak
Medium
Strong
Very Strong
Order Qty
100
100
100
100
* Not suitable for use with JobMaster™
Strip Powerloads to suit Previous Ramset™
Strip Feed Tools & Hilti™ Strip Feed Tools
Powder Actuated Systems
Specifications
Power Load Strip designed for use with Ramset™ tools; FrameBoss™,
FormMaster™, TyMaster™, FixMaster™ (TS60P), FrameMaster™ (TS750(P)),
S75A, FrameFix™, Striker, Rocket. Also suitable for use with Hilti tools;
DX460, DX351, DX-A40/41, DX36.
Specifications
Charge Type
Calibre
Part No
PLSGR22
PLSYW22
PLSRD22
10 Shot Strip
6.8 x 11mm
Calibre
6.8mm x 11mm
6.8mm x 11mm
6.8mm x 11mm
Colour
Green Yellow Red Strength
Weak
Medium
Strong
www.ramset.com.au
Order Qty
100
100
100
1300 780 063
61
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising