Snap Stand - The Tapco Group
S n a p
S t a n d
Installing a ProTrax™ or MaxTrax™ Saw Table on Snap Stand®
snap buttons are
toward working
side of saw table
use these clips
Figure 1
use these holes
STEP 1
Using the 1/4-20 bolts and lock washers provided, fasten the ProTrax/MaxTrax mounts to the Leg Set. The
snap buttons will be on the working side of the brake. Repeat for the other Leg Set. Be sure both ends of
the Snap Stand are going the same direction (with the snap buttons on the same side) See Figure 1 above.
rear lip
rear lip
bypassing
rear clip
Figure 2
STEP 2
Place the ProTrax/MaxTrax on the
Snap Stand Assembly with the rear
lip of the sub structure clearing the
rear clip. See Figure 2 above.
Figure 3
STEP 3
The snap button will be
covered by the front sub
structure of the ProTrax/
MaxTrax. See Figure 3 above.
Figure 4
STEP 4
Push the ProTrax/MaxTrax firmly
rearward into the rear clips. The
snap buttons will pop up and
secure the saw table on the Snap
Stand. See Figure 4 above.
Removing the ProTrax or MaxTrax:
1. Removing the ProTrax/MaxTrax from the Snap Stand is essentially the opposite of attaching it to the stand.
2. Depress the snap button and pull the saw table forward far enough to hold each snap button down.
3. Be sure the lip on the rear sub structure is out of the Rear Clip. The ProTrax/MaxTrax can now be removed
from the stand.
4. Reverse Steps 1 and 2 on page 2 to disassemble the stand for transport.
29797 Beck Road • Wixom, MI 48393-2834
www.tapcoint.com
3
© 2010 Headwaters. All rights reserved.
Item # 11987
T7924 1/10
Snap Stand
Operating Instructions
Shown with optional Wheel Kit
Contents
• General Instructions
• Installing Brake on Snap Stand
• Removing the Brake
• Installing ProTrax or MaxTrax Multi-
Angle Saw Table on a Snap Stand
• Removing the ProTrax or MaxTrax
• Wheel Kit Installation
®
S n a p
S t a n d
Setting up your Snap Stand®
STEP 1
To open each Leg Set, push in the snap button and move each leg outward to the working
position. Figure 1A below shows the leg set as shipped while Figure 1B shows the leg set
open (working position). Make sure that the snap button pops up to lock each leg.
Figure 1A
Snap Button locations
when legs are closed.
Snap Button locations
when legs are open.
Figure 1B
STEP 2
Attach the Cross Braces to the Leg Sets. With the snap
button of the Leg Set pointing to the outside, snap the
Cross Braces into position. See Figures 2A and 2B below.
Note: Be sure the C-shape of the
Cross Brace is mating the leg as
shown in Figure 2C below.
Figure 2B
Figure 2A
Figure 2C
Attaching Optional Wheel Kit
Use one of these
positions to stop the
stand from rolling.
STEP A
Insert the wheel assembly into the leg of
the Snap Stand as shown in the figure
above. Tap the bracket with a hammer to
wedge it tightly into the leg. Repeat this
process for the other leg.
STEP C
To remove the wheel
assembly, tap the
bracket downward with
a hammer to disengage.
STEP B
To prohibit the stand from rolling on the wheels, lock the leg extensions into one of the bottom two locking positions. See figure
above. If the leg extensions are in one of the other 3 positions, the
wheels are in contact with the ground and are free to roll.
1
S n a p
S t a n d
Installing a Brake on Snap Stand®
STEP 1
Using the 1/4-20 bolts and lock
washers provided, fasten the brake
mounts to the Leg Set. Depending
on which brake you’re using,
choose the correct holes as shown
in the figure at right.
PRO-14™
PRO 19™
snap buttons are
toward working
side of brake
Figure 2
Back Rail clearing
adaptor hook
Figure 3B
Figure 3A
STEP 2
The snap buttons will be towards
the working side of the brake.
Repeat Step 1 for the other Leg
Set. Be sure both ends of the Snap
Stand are going the same direction
(with the snap buttons on the same
side). See Figure 2 above.
STEP 3
Place the brake on the assembled
Snap Stand with the Back Rail of
the brake clearing the adaptor
hook as shown in Figures 3A and
3B above.
Button pops up when brake is
fully seated
Figure 3C
The snap button will be covered
by the fixed hinge of the brake as
in Figure 3C above.
PRO-14™
STEP 4
Push the brake firmly rearward
into the adaptor hooks. The snap
buttons by the front clips will pop
up and secure the brake on the
Snap Stand. See Figure 4 above.
The brake is now ready for use.
2
Removing the Brake:
1. Removing the brake from
the Snap Stand is essentially
the opposite of attaching it to
the stand.
2. Lifting the Moving Hinge,
depress the snap button and pull
the brake forward far enough to
hold each snap button down.
3. Be sure the box rail is out of
the Rear Clip. The brake can
now be removed from the stand.
4. Reverse Steps 1 and 2 on page 2
to disassemble the stand
for transport.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising