Document
DWF8010
14 place settings
Alt function
www.fulgor.com.au
For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Fill the detergent dispenser
Check the rinse aid level
Load the baskets
Select a programme
Running the dishwasher
Open the door, press the On/Off button to switch on the appliance.
With each wash cycle.
Compartment
For programmes with pre-wash only.
(Follow the user instructions!)
Electric indicator on control panel (if provided).
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Press the Programme Button, the selected programme indicator lights up.
( See the section entitled“Operation instruction”)
Close the door, t urn on the water tap . The machine will start working
after about 10 seconds.
Changing the programme
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Open the door, press the program button more than 3 seconds, the machine will be in
standby state, then you can change the program to the desired cycle setting.
Add forgotten dishes in the
dishwasher.
1.Open the door a little to stop the washing.
2.After the spray arms stop working, you can open the door
completely.
3.Add forgotten dishes.
4.Close the door, the dishwasher will run after 10 seconds.
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state.
Switch off the appliance
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
Turn off the water tap,
unload the baskets
Open the doo r carefully.
Hot steam may esc ape
when the door is opened!
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Dear Customer,
This appliance is in tended to be used in household
and similar applications such as:
-staff kitch en areas in shop s, offices and other
working environme nts;
-farm hous es;
-by clients in hotels, motels and othe r residential
type environments;
-bed and breakfast type environments.
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it as a refer in the later days.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installat ion I nstructions and
Tr oubleshooting Tips, etc.
Control Panel...................................................2
Dishwash er Features.................................... ...2
A、F ill the Rinse Aid Dispenser............. ..... .. ... ..3
B、Function of Detergent ........ .........................4
Attention b efore o r after loading the Dish washer
Ba skets..........................................................6
The Method Loading Normal Dishware ... ...........7
Wash Cycle Table...........................................9
Turning on the Appliance................................9
Change the Programme.............. .... ................10
At the End of the Wash Cycle...........................10
Filtering System.............................................11
Caring for the Dishwasher..................... . .........12
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solv e the problems by yourself ,
please ask for the help of professional technicians.
Po sitioning the Appliance................... .. ..........13
Ab out Power Connection........................ . .......13
Water Co nnection.................................. . .......14
Start of dishwasher................................ .. ......15
Be fore calling for service........................... . .....16
Error codes.................................... . ..............17
Tech nical info rmation.............................. .......18
The manufacturer, following a policy of constant
development a nd u pdating of the product, may
make modifications without giving prior notice.
When using your dishwasher, follow the precautions listed below:
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Children should be supervised to ensure that they do
not play with the appliance.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed :
1) Locate sharp items so that they are not likely
to damage the door seal;
2 ) Warning: Knives and other utensils with
sharp points must be loade d in the basket
with their points down or placed in a
horizontal position.
Check th at the detergent comparment is e mpty
after completion of th e wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only deterge nt and rinse additives
designed for an automatic dishwasher.
Never use soap, laun dry dete rgent, or hand
washing detergent in you r dishwa sher. Keep
these products out of the reach of children.
Keep children away from detergent and rinse aid, keep
children away from the open door of the dishwasher,
there could still be some detergent left inside.
This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Dishwash er detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left open,
since this could increase the risk of tripping.
If the s upply cord is damaged, it must be replaced
by the man ufacturer or its serv ice agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please d ispose of packing materials properly.
Use the dishwasher only for its intended function.
During installatio n, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum nu mber of place settings to be
washed is 14 .
The maximum pe rmissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa .
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
Program Button : To Press the button to select
appropriate Program.
Alt Button: Dual zone wash function, press the
button to select either upper basket or lower basket
loaded, and the response indicator .
Program step indicators:
On/Off Button: To turn on/off the power supply.
Delay Button : To Press the button to delay.
Display screen : to sho w the remaining time
and the state(ru nning sta te, delay time etc )
Program indicators:
Rinse Aid indica tor:
Indicates when the dispenser needs to be refilled.
Pre-wash indicator:
Main-wash indicator:
Rinse indicator:
Drying in dicator:
Prog ram end indicator:
Delay time ,Remain time ,or error codes indicator:
Alt function indicator:
Ba ck View
Front view
1
2
3
7
4
5
8
9
6
10
1
2
3
Top spray arm
Cutlery rack
Upper basket
4
5
6
Inner pipe
Lower basket
Dispe nser
7
8
9
11
Cup shelf
Spray arms
Filter assembly
10
11
Inle t pipe conne ctor
Drain pipe
Before using your dishwas her for the first time:
A. Fill th e rinse a id dispenser
B. Fill in detergent
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black . The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning lig ht in the control p anel, you can judge the amount of rinse-aid by the color of the
optical level
indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the
rinse-aid
diminis hes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid lev el indicator changes, as illustrated be low.
Fu ll
3 / 4 fu ll
1 / 2 fu ll
1 / 4 fu ll - Should refill to eliminate spotting
Empty
RINSE AID DISPENSER
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.
Attention!
Clean up any rinse aid spill during filling with an absorbent cloth to avoid excess foaming
during the next wash.
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to repla ce the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a pro ble m, increase the amount of rinse
aid dispensed by removing the dispe nser lid and rotating the dial to "5". If the
dishes still are not drying properly or show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phos phate and without chlorine
3.Without phosphate and without chlorine
Normally new pulveris ed d etergent is without p hosphate. Thus the water softene r function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 °dH. If detergents without phosphate are used in the case of hard water
often white sp ots appear o n dishes and gla sses. In this case please add more detergent to reach
better results. Detergents with out chlorine do only bleach a little. Strong and coloured sp ots will not
be removed completely. In this case please choose a progra m with a higher temp erature.
Concentrated Detergent
Ba sed on their chemical composition, detergents can be split in two basic types:
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
Th e use of“no rmal ” washing programs in combination with concentrated detergents
reduces pollution a nd is good for your dishes ; these wash programs are specifically matched
to the dirt-diss olving prope rties of the enzymes of the concentrated detergent. For this reason
“normal”wash programs in which concentrated detergents are used can achieve the same
results that can oth erwise only be achieved using “intensive ” programs.
Detergent Tablets
Deterg ent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve an d develop their full cleaning power during short
progra ms. Therefore please use long programs when using d etergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
Th e dispenser mus t be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More h eavily soiled items need more deterge nt. Always add the
detergent just before starting the dishwasher, otherwise it could g et damp and will not
dissolve properly.
Amount of Detergent to Use
Detergent powder
Detergent tablet
If th e lid is close d: press rele ase button. The lid will spring ope n.
Always add the dete rgent just before starting each wash cycle.
Only use branded detergent aid for d ishwash er.
Dishwasher detergent is corrosive! Take care to keep it ou t of reach of c hildren.
Proper Use of De terg ent
Use only deterge nt specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered d etergent into the dispenser until you're ready to wash dishes.
Fill in Detergent
Fill the detergent dispen ser with detergent.
The marking ind icates the dosing levels , as
illustrated o n the right:
A
The place of main wash cycle detergent placed.
B
The place of pre-wash cycle detergent placed.
Please observe the man ufacturers dosing an d storag e
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
deterge nt dose in the pre-wash detergen t ch amber. This detergent will take effect during the pre-wash phase.
You find information abou t the amount of detergent for the single programme on the las t page.
Plea se a ware, that according to the level soiling and the specific hardness of water differences are possible.
Plea se o bserve the manufacturer's recommendations on the detergent packaging.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low a temperature as possible.
To prevent damage, do not take gla ss a nd c utlery out of the dishwasher immediately
after the programme h as ended.
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
(For best performance of the dishwasher, follow these loading guide lines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts o f leftover food. Soften remnants of burnt food in pans.
It is not necess ary to rinse the d ishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots /pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items suc h as cup s, glasses, pans etc. With the opening facing downwards so that
water can not collect in the con tainer or a deep b ase.
Dishes and items of cutlery must not lie ins ide one another, or cover each oth er.
To avoid damage to glasse s, th ey must not touc h.
Load large ite ms which are most difficult to clea n into the lower bask et.
The upper basket is designed to ho ld more delicate and lighter dishware such as glasses , coffee
and tea cups
Long bladed knives stored in an upright position are a potential haza rd!
Long and/or sharp items o f cutlery such as carving kniv es must be positioned
horizonta lly in the upper b asket.
Please do not ove rload yo ur dishwasher. This is important for good results and for
reasonab le consumption of energy.
To prevent water dripping from the uppe r basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.
The u pper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishe s an d co okware so that they will
not get moved by the spray of wate r.
We suggest that you place large items and the most
difficult to clea n ite ms are to be placed into the lo wer
basket: such as pots, pans, lids, se rving dishes and
bowls, as shown in the figure below. It is pre ferable to
place serving dishes and lids on the side of the rack s
in order to avoid blocking the ro tation of the top spray
arm.
Please be reminded that:
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slan ted to allow water to flow out.
The Botto m Basket features fo lding spikes so that larger or more pots and pans can be loaded.
Adjusting the Upper Basket
Folding back the cup shelives
The height of the upper basket can be adjusted in order to Fo r better stacking of po ts and pans,
the spikes c an b e folded down as
create more space for large utensils both for the upper
sho w in the picture right.
/lower basket. The height of the upper basket can be
adjusted by lift up the basket for the upper position, and up
press the handle to lower the upper basket, see the picture
below:
Folding Spikes of Lower Basket
Fo r better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Cutlery should be pla ced in the cutlery rack separately
from each other in th e ap propriate positions, and d o
make sure th e utensils do not nest together, this may
cause bad performance.
For a top quality cleaning, place the silverware in the basket
making sure that:
They do not nest together.
Silverware is placed with the male face up.
Long utensils in the middle.
Cutlery basket has 5 positions:
Mode 1
Position one: lift the left basket up, both left and right
baskets are slanting.
Mode 2
Position two: adjust the left basket to lower position, left
basket is flat and right basket is slanting.
Mode 3
Position three: lift the right basket up, both left and right
baskets are flat.
Mode 4
Position Four: Move the right basket from right to left, two
basket are overlapping.
Mode 5
Position Five: Remove the right basket from the tray,
only has the left basket.
(
Intensive
Heavy
Normal
) Means: need to fill rinse into the Rinse-Aid Dispenser.
For the heaviest soiled
loads, such as pots, pans,
casserole dishes and dishes
that have been sitting with
dried food on them for a
while.
Pre-wash(50℃)
Wash (65 ℃)
Rinse
Rinse
Rinse(55℃)
Drying
Fo r heavily soiled loads,
such as pots, plates, gla sses
and lightly soiled pans.
Pre-wash(45 ℃)
Wash (55 ℃)
Rinse
Rinse (60 ℃)
Drying
Pre-wash
Wash (45 ℃)
Rinse
Rinse(50℃)
Drying
Pre-wash
wash(40℃)
Rinse
Rinse(60℃)
Drying
Standard daily cycle for
normally soiled loads, such
as pots、plates、glasses.
(*AS/NZS 200 7.1)
Glass
1Hour
Rapid
For lightly soiled cr ockery
and glass
For lightly soiled loads that
do not need excellent drying
efficiency.
Pre-wash(50℃)
Wash(60℃)
Rinse (50℃)
Drying
A shorter wash for lightly
Wash (40 ℃)
soiled loads and quic k wash. Rinse
Rinse (45 ℃)
5/27 .5g
(Or All in1)
165
1.4
16.5
5 /27.5g
(Or All in1 )
175
1.2
13.5
5/27.5g
(Or All in1 )
165
0.74
12.6
20g
115
0.85
13.5
5/27.5g
60
0.85
9
20g
35
0.5
10
* AS/NZS 2007.1 : This program is the test cycle. The information for comparability test
in accordance with AS/NZS 2007.1 , as follows:
Capacity: 14 setting
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
Open the door slightly 50mm to assist in drying of the dishes after every wash
Startin g a cycle wash
1 Draw out the lower and upper basket, load the dishes a nd push them back.
It is commended to load the lower basket first, then the upper one (see the section entitled
“Loading th e Dishwashe r”).
2 Pour in the detergent (se e the section entitled“Detergent and Rinse Aid”).
3 Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ , th e specificatio n
of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
4 Open the door, p ress the ON/OFF Button, and the display will turn o n.
5 Press the program Button to selected your desired program.
If a pro gram is selected , the resp onse light will light. Then close the door, the dishwasher begins
to start.
Premis e:
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
d etergent may have already been relea sed, and the appliance may have already drain ed the wash water.
If this is the case, th e detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
2 Open the door , the machine will pause, press the program bu tton more than
3 s then you can cha nge the program to the desired cycle setting (see the section entitled " Starting a wash
cycle. . ." ).
1
If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door . After
you close the door ,the machine will keep on working after 10 sec onds.
A forgotten dish can be added any time before the detergent cup opens.
3 Add forgotten dishes.
1 Open the door a little .
2
After the spray arms stop working, you can open the door
completely.
4
Close the door, the dishwasher will run
after 10 seconds.
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 sec onds, then stop. Turn off
the appliance using the ON/OFF button, shut off the wate r supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the ON/OFF butto n.
2.Turn o ff th e water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool d own around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler an d the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty th e lower basket first and then the upper one. T his will avoid water dripp ing from the upper Basket onto
the dishes in the lower one.
Wash the arms in When
soapy following
and warmthis
water
and use from
a softstep1
brushtotostep 3, the filter system will be removed;
procedure
It is dangerous
tothem
openthorough
the door when washing, because the hot water may scald you.
clean the jets. Replace
them
afteritrinsin
when following
from gStep
3 to Step 1,ly.the filter system will be installed.
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter, a flat (Main filter)
And a microfilter(Fine filter).
Main filter
2
1
Fo od and soil particles trap ped in this filter are pulverized by a
specia l jet on the lower spray arm and washed down to drain.
1
Coarse filter
2
La rger ite ms, such as p ieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
3
Fine filter
3
This filter holds soil and food residues in the sump area a nd
preve nts it from being redeposit on the dishes during wa sh cycle.
Filter assembly
The filter efficiently re mo ves food particle s from the wash water, allowing it to be rec ycled during the cycle.
For best performance and results, the filter must be cleaned re gularly. For this reason, it is a goo d idea to
remove the larger food particles trapp ed in the filter after e ach was h cycle by rinsing the semicircular filter and
cup under runnin g water. To remove the filter device, pull the cup handle in the upward d irection.
The d ishwasher must never b e used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
1
Step 1:Turn the filter in anti-clockwise direction,
2
Step 2:lift the filter assy up
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
Remarks:
- Inspect the filters for blo cking a fter e very time the dishwa sher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Re move any foo d remna nts and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a c leaning b rush. Reassemb le the filter p arts as shown in the figures
on the last page and reinsert the entire assembly in the dis hwa sher, positio ning it in its seat and pressing downwards.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the e dge around the door, you should use only a soft warm, damp cloth.
To avoid pene tration o f wa ter into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door loc k
and electrical components.
Abrasive agents or some paper towels shou ld not be used becau se of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time a fter washing cycles,
please operate as follows:
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe an d water valve. (Use a pan to gather th e water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
If your dishwasher cannot work because of the ice,
please contact professional service persons.
Cleaning the Spray Arms
It is necessary to clean the spra y arms re gularly fo r hard
wate r che micals will clog the sp ray arm jets a nd bearings.
To remove the up per spray arm, hold the nut, rotate the arm
clockwise to remove it.
To remove th e lower spray arm, pull out the spray arm u pwa rd.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
After Every Wash
When not in Use for a LongTime
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
It is recommend that you run a was h cy cle with the
dishwasher empty an d the n remove the plug from the
socket, turn off the wa ter supply and leave the door of
the appliance slightly open. This will help the d oor
seals to last longer and prevent odours from forming
within the appliance.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
No Solvents or Abrasive Cleaning
To cle an the e xterior a nd rubber p arts of the dishwasher,
do not use solvents or abrasive cle aning products.
Only use a clo th with warm so apy water.
To remove spots o r stains from the surface of the
interior, use a cloth da mpened with water a n a little
vinegar, o r a cleaning pro duct mad e specifically for
dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. T he dishwasher is equipped with water supply and drain hoses th at can
be positioned either to the righ t or the left sides to facilitate proper installation.
Once the appliance is positioned for levelling, the height of the dishwashe r
may be altered via adjustment of the screwing level of the feet. In any case,
the applia nce should not be inclined more than 2 .
For personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Plea se look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp , time delay fuse or c ircuit breaker recommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power being correspond s to
those on the rating plate. Only in sert the plug into an electrica l socke t which is earthed
prop erly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a a daptors or the like as
they could cause ove rheating an d burns.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
Improper connection of the equipment earthing conductor can result in the risk of an
for personal safety:
electric shock.
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
Check with
qualified
electrician
or service representative
if you areTHE
in doubt
whether the
DO a
NOT,
UNDER
ANY CIRCUMSTANCES,
CUT OR REMOVE
EARTHING
appliance
is properly earthed.
CONNECTION
FROM THE POWER CORD.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.
The a ppliance mus t be connected to th e water mains using n ew hose-sets.
The o ld hose-sets sho uld not be re used.
Wate r pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the
minimum consult our Service Department for advice.
1
2
3
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
Turn water fully on before starting the dishwasher.
The safety supply hose con sists of the double walls. The hose's system guarantees its intervention by blocking the
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer
corrugated hose is full of water.
A hose that attaches to a sink spray can burst if it is installed on the same water line as the d ishwash er. If your sink
has one, it is recommended that the hose be disconnected and the hole plu gged.
1Turn off the water.
the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
2 Release
room, from severe splashing.
3 Unscrew the safety supply hose from the faucet.
Connect the cold water supply hose to a thread ed 3/4(inch) conn ector an d make sure that it is fastened tightly in place.
If th e water pipes are new or have not been use d for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked
and damage the appliance.
Drain hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Front
Counter
Drain pipe
A
MAX 1000mm
NOTE
The top of the hose
must be less than
1000mm.
B
40mm
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height less than 1000 mm (maximum) from the bottom of the dish.
The water drain hose should be fixed .
Start of Dishwasher
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 The power plug is correctly plugged in
4 The power is switched on
5 The inlet and drain hoses are connected
6 All packing materials and printings should be taken out from the dishwasher
Attention:
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
15
Fuse blown, or the
circuit breaker tripped
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Error code:E1;
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
Kink in drain hose
Check drain hose.
Filter clogged
Check coarse the filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 4 litres of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step. Open the door after draining
is stop and check if the suds have disappeared.
Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
The affected items are
not corrosion resistant.
A programme was not
Always run the quick wash programme .
without any crockery in the dishwasher and
run after dishwasher
without selecting the Turbo function (if present),
salt was added.
Traces of salt have
after adding dishwasher salt.
gotten into the wash cycle.
The lid of the softer
is loose
Check the lid .Ensure it is correctly closed.
A spray arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Items of crockery
are loose in the
wash cabinet
Interrupt the programme,
and rearrange the items of crockery.
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
the path of spray arms.
Rearrange the items so that the spray arm can rotate
freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Use of cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
When some malfunctions come on, the appliance will display error codes to warn you:
E1
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
E4
Overflow.
Some element of dishwasher leaks .
E8
Failure of orientation of distributary valve.
Open circuit or break of distributary valve.
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
Height :
Width :
Depth :
845mm
598 mm
600mm (with the door closed)
Water pressure:
Power supply:
Capacity:
0.04-1.0MPa
see rating label
14 place settings
a
a
c
c
e
a
b
a
b
f
IN
2.Lower basket:
a
a
a
IN
1.Upper basket:
a
a
c
c
c
d
c
c
c
c
c
c
c
a
a
c
c
f
f
a
a
a
Dessert dishes
f
Soup plates
e
Dinner plates
d
Glasses
c
Saucers
b
a
Cups
Loading the baskets according to (*AS/NZS 2007.1) :
5
2
Information for comparability tests in
accordance with (*AS/NZS 2007.1)
Voltage:230V/5 0Hz
Capacity: 14 place settings
Position of the upper basket: lower
Programme: Normal
Detergent(Pre/ main): 5 g/27.5 g
Rinse aid setting: 6
3 Dessert spoons
2 Soup spoons
1 Forks
1
3
4
3.Cutterly basket:
5 Knives
4 Teaspoons
4
3
1
2
5
IN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising