Comnet FVT/FVR10D2I1C4E Datasheet

Comnet FVT/FVR10D2I1C4E Datasheet
10-bit Digitally Encoded Video + 2 Bi-directional Data
+ Aiphone™ Intercom + 4 Contact Closure + 100Mbps Ethernet
+ Redundant Point-to-Point Dual SFP* Optical Ports
FVT/FVR10D2I1C4E
INCLUDED
HARDENED
1 CH
3 CH
1 CH
2 CH
1 CH
1 CH
The ComNet™ FVT/FVR10D2I1C4E environmentally hardened units provide
transmission of one independent video channel and two bi-directional data channels.
They also provide transmission of one Aiphone™ intercom channel and four contact
closure channels with tamper supervision in addition to one 10/100Mbps Ethernet
channel. The FVT/FVR10D2I1C4E has dual SFP optical ports to provide a redundant
point-to-point fail safe topology in the event of loss of one fiber or one optical
module. Plug-and-play design ensures ease of installation and no electrical or optical
adjustments are ever required.
FEATURES
› 10-bit digital video encoding and decoding for high-quality
video transmission that meets the requirements of EIA
RS-250C for short-haul video transmission
› Bi-color (Red/Green) LED status indicators provide rapid
indication of critical operating parameters in addition to alarm
contacts for fault monitoring
› 2 Bi-directional data channels supporting RS232, RS422, and
2 or 4-wire RS485 with tri-state data interfaces
› Duplex Aiphone™ intercom channel
› Operational status monitored via web management interface
through the addition of the ComNet network managed
chassis and network management interface module
› Four contact closure channels with supervision
› Hot-Swappable Modules
› True 100Mb Ethernet channel
› Interchangeable between stand-alone or rack mount use –
ComFit
›D
ual SFP optical ports redundant Point-to-Point configuration
› Exceeds all requirements for RS-250C short-haul transmission
› Voltage transient protection on all power and signal input/
output lines provides protection from power surges and other
voltage transient events.
› Lifetime Warranty
› Made in the USA
* Small Form-Factor Pluggable Module. Sold separately.
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
FVT/FVR10D2I1C4E
10-bit Digitally Encoded Video + 2 Bi-directional Data + Aiphone™ Intercom + 4 Contact
Closure + 100Mbps Ethernet + Redundant Point-to-Point Dual SFP Optical Ports
SPECIFICATIONS
Video
Indicating LEDs- Power - Link - Video - Data
Video Channels
Video Input
Overload
Bandwidth
Differential Gain
Differential Phase
Tilt
Signal-to-Noise Ratio:
1
1 volt pk-pk (75 ohms)
>1.5V pk-pk
10 Hz – 6.5 MHz
<2%
<0.7º
<1%
67 dB Typical
- Intercom - Contact Closure - Ethernet
Connectors
Data
Data Channels
Data Interface
Data Format
Data Rate
Bit Error Rate:
Operating Mode:
2
RS232, RS422 and RS485 (2W/4W)
NRZ, MRZI Manchester, Bi-Phase and Sensornet
DC-250 Kbps (NRZ)
<1 in 10-9 @ Maximum Loss Budget
Simplex or Full-Duplex
Intercom
Channels
Compatibility
1
Aiphone™ LED and LEF
Ethernet
Power
Operating Voltage Range
Power Consumption
Dual Redundant Input 8 to 24 VDC
4W
Electrical & Mechanical
Current Protection
Circuit Board
Size (L × W × H)
Shipping Weight
Automatic Resettable Solid-State Current Limiters
Meets IPC Standard
6.1 × 5.3 × 2.2 in (15.5 × 13.5 × 5.6 cm)
< 2 lb / 0.9 kg
Environmental
Data Interface
Data rate
Maximum Bitrate
10/100 BASE-T/TX
10/100 Mbps Full Duplex
100Mbps
Contact Closure
Optical2 × SFP, Dual Port configuration¹
Power
Terminal Block
Video
BNC
Data
RJ45
Intercom
RJ45
Contacts
RJ45
Ethernet
RJ45
Alarms
RJ45
Channels
Response Time
Input
Output
Supervision
MTBF
Operating Temp
Storage Temp
Relative Humidity
> 100,000 hours
-40ºC to +75ºC
-40ºC to +85ºC
0% to 95% (non-condensing)²
3 Simplex, 1 Duplex
25 msec
Dry Contact Closure
SPST Relay, 0.5 A Contact rating – normally open
Open Circuit / Short Circuit Detection
ORDERING INFORMATION
# Rack
Slots
Part Number
Description
Fiber Information
FVT10D2I1C4E
Transmitter Video / Bi-directional Data / Aiphone™ Intercom / 4 Contact Closure / 100Mb Ethernet / SFP
See SFP Modules data sheet
2
FVR10D2I1C4E
Receiver Video / Bi-directional Data / Aiphone™ Intercom / 4 Contact Closure / 100Mb Ethernet / SFP
See SFP Modules data sheet
2
Accessories
DC Plug-in Power Supply (Included)
Options
[2] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)
DIN-Rail Mounting Adaptor Plate Kit - with Mounting Hardware (Optional, order model DINBKT1 or DINBKT4)
[1] Multimode fiber needs to meet or exceed fiber standard ITU-T G.651. Single mode fiber needs to meet or exceed fiber standard ITU-T G.652.
Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J. In a continuing effort to improve
and advance technology, product specifications are subject to change without notice.
TYPICAL APPLICATIONS
OPTICAL FIBER
COPPER CABLE
V
D
V
2
I
2
FVT10D2I1C4E
E
Dual Redundant
Fiber Links
SFP dependent
fiber selection
I
FVR10D2I1C4E
E
C
C
D
C
3
3
C
3 CORPORATE DRIVE | DANBURY, CONNECTICUT 06810 | USA | T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [email protected]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE | T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | [email protected]
© 2015 Communication Networks. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks.
05 Jan 2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement