GRAFIK Eye® QS Wireless Control Unit with EcoSystem

GRAFIK Eye® QS Wireless Control Unit with EcoSystem
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 1 07.16.12
GRAFIK Eye® QS Wireless Control Unit with EcoSystem®
Open
1
Preset
2
Close
3
4
Off
LUTRON
Description
GRAFIK Eye® QS Wireless with EcoSystem® is the premier energy-saving
lighting and shade control. The GRAFIK Eye® QS control unit features an
astronomic timeclock and intuitive lighting presets, which are seamlessly
integrated with EcoSystem® fluorescent ballasts and LED drivers, and Lutron’s
QS components and systems. Now with wireless technology and an integral
EcoSystem® bus supply, you can use the GRAFIK Eye® QS Wireless control
unit with EcoSystem® to control ballasts and shades without interfaces, and
integrate with a variety of Lutron wireless products and systems, including
Radio Powr SavrTM occupancy, vacancy, and daylight sensors, Sivoia®
QS wireless shades, Pico® wireless control, and other GRAFIK Eye® QS
wireless control units. Additionally, the GRAFIK Eye® QS wireless control
unit is compatible with all Lutron wired QS products and systems, including
Quantum®.
Mechanical Dimensions
94 in
(239 mm)
4 in
(10 mm)
2 in
(51 mm)
4$ in
(119 mm)
Front View
Side View
Fits into a 4-gang U.S. backbox, 3` in (90.4 mm) deep (Lutron P/N 245-254) or
3 in (76.2 mm) deep (Lutron P/N 241-400)
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 1
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 2 07.16.12
System Topologies
The GRAFIK Eye® QS Wireless control unit with EcoSystem® can be specified in three different system topologies.
Examples of each are shown below.
Example of Wired System
Wired QS link
LUTRON
LUTRON
GRAFIK Eye® QS
wireless control unit
GRAFIK Eye® QS
wireless control unit
LUTRON
LUTRON
LUTRON
Quantum®
processor
LUTRON
seeTouch®
QS
wallstation
LUTRON
LUTRON
QSE-CI-NWK-E
Sivoia® QS
shade
QS Sensor
Module
LUTRON
LUTRON
LUTRON
Wired
occupancy
sensor
EcoSystem®
ballast
Energi Savr
NodeTM unit
Example of GRAFIK Eye®-centric
Wireless System
Example of Mixed GRAFIK Eye®-centric
Wired/Wireless System
30 ft
(10 m)
wireless
range;
60 ft
(20 m) in
open air
GRAFIK Eye® QS
wireless control unit
Wireless
daylight
sensor
Wireless
Sivoia® QS
shade
LUTRON
Wired QS link
LUTRON
LUTRON
Pico®
wireless
control
LUTRON
Wireless
occupancy
sensor
LUTRON
GRAFIK Eye® QS
wireless control unit
GRAFIK Eye® QS
wireless control unit
LUTRON
LUTRON
LUTRON
seeTouch® QS
wallstations
Wireless
Sivoia® QS
shade
LUTRON
EcoSystem®
ballasts
EcoSystem®
ballasts
Pico® wireless
control
Wireless
daylight
sensor
S pecificat ion Sub mitt al
LUTRON
®
Job Name:
Job Number:
Page 2
LUTRON
LUTRON
Model Numbers:
LUTRON
Wired
occupancy
sensor
Wireless
occupancy
sensor
LUTRON
LUTRON
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 3 07.16.12
Application Suggestions and Differences between GRAFIK Eye® QS with EcoSystem® Control Unit
and Energi Savr NodeTM with EcoSystem® Unit
GRAFIK Eye® QS with
EcoSystem®
Energi Savr NodeTM (ESN)
with EcoSystem®
ESN
Wireless
router
LUTRON
GRAFIK Eye® QS with
EcoSystem® control unit
Mobile
digital
device
Suggested/Recommended Applications
Single rooms, partitioned spaces,
e.g., conference room, classroom,
ballroom, lobby
Open spaces, multiple
enclosed rooms, e.g., open
office, window offices
Programming Method
Info Screen on the QS control unit
Via Energi Savr NodeTM App for
iPod mobile digital device
Integral Timeclock
Yes
Yes (using a QS Timeclock or
contact closure interface)
Compatible with seeTouch® QS Keypads
Yes
Yes
Compatible with EcoSystem® Wall Controls
No
Yes
Compatible with EcoSystem® IR Sensors
No
Yes
Includes dry contact closure for integration to BMS
or Security Systems
Yes
Yes
Input Voltage
120-127 or 220-240 V
50/60 Hz
120/240/277 V
50/60 Hz
Number of EcoSystem® Busses
1
1 or 2
Number of Zones
6, 8, or 16
Programmable (maximum 100)
Number of Line-Voltage Outputs
3 (Zones 1-3 only)
--
Compatible with other QS Devices
Yes
Yes
iPod is a trademark of Apple Inc., registered in the United States and other countries.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 3
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 4 07.16.12
Open
1
Preset
2
Close
3
4
Off
LUTRON
Note: General Engraving (-EGN) shown.
1
2
3
4
5
6
OK
Open
1
Preset
2
Close
3
4
Off
USB type
mini B
Optional
shade
control
keypad
Zone
control
®
Infrared
receiver
Lighting
control
keypad
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Info
screen
Features
• Lutron’s proprietary Clear Connect® RF technology.
Operates in the 434 MHz band.
• Pushbutton recall of four preset lighting scenes,
plus Off.
• Sixteen (16) total available scenes, plus Off scene.
• Zones 1, 2, and 3 can control many light source
types directly or through power modules.
• Optional integrated shade control buttons, which
can also be added to the unit after installation.
• Master override buttons to raise and lower all lights.
• Allows setup of lighting scenes and shade presets
using buttons on the control unit.
• Built-in infrared (IR) receiver.
• External IR connection.
• Built-in astronomic timeclock.
• Info screen shows zone light level percentage,
energy savings, zone labeling, programming, and
EcoSystem® setup.
• Lockout option prevents accidental changes.
• Occupancy sensor input and 24 V power for one
occupancy sensor.
• QS communication link for seamless integration of
lights, motorized window treatments, occupancy
sensors, wallstations, and integration interfaces.
• Compatible with all Lutron QS system components.
• Wireless communication for seamless integration
with a variety of Lutron wireless products and
systems, including Radio Powr SavrTM occupancy,
vacancy, and daylight sensors, Sivoia® QS wireless
shades, Pico® wireless controls, and other
GRAFIK Eye® QS Wireless control units.
• Control up to 6, 8, or 16 EcoSystem® zones from
internal bus supply.
• Zones 1, 2, and 3 are integral line voltage dimming
zones and can be optionally programmed as
EcoSystem® zones.
• Up to 64 EcoSystem® or Hi-lume® 3D ballasts can
be addressed and grouped to zones.
• Integral EcoSystem® setup and programming
through the info screen.
• Backlit buttons with engraving make unit easy to
locate and operate.
• Available in a variety of colors and finishes.
Page 4
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 5 07.16.12
Specifications
Input Power
• 120 - 127 V
• 220 - 240 V
Zones 1, 2, and 3 can also control the following lighting
sources with a smooth, continuous square law dimming
curve or on a full conduction non-dim basis through
separate Lutron power modules:
• Electronic low-voltage transformers (use ELV or
Phase-Adaptive power module)
• Lutron 3-wire controlled electronic fluorescent dimming
ballasts (use fluorescent 3-wire power module)
• Non-dim (use switching module)
• 0 - 10 V (use TVI)
50/60 Hz
50/60 Hz
Listings (120 - 127 V
• UL
• CSA
• NOM
• CEC (Title 24)
• FCC Part 15 Class B
• IC RSS-210
• SCT
)
Note: A zone may be programmed to control only one load
type at a time.
Environment
• 32 to 104 °F (0 to 40 °C)
• Relative humidity less than 90% non-condensing
Lighting Sources/Load Types
All Zones
• EcoSystem® and Hi-lume® 3D ballasts, and Hi-lume®
LED drivers directly wired to integral EcoSystem® digital
link
• Before system is addressed, Zone 4 will transmit
broadcast commands to all EcoSystem® loads wired to
the GRAFIK Eye® QS.
• Zones on Energi Savr NodeTM products wired to the
same QS link
- Zones on Energi Savr NodeTM with Softswitch®
- Zones on Energi Savr NodeTM for 0-10 V
- Zones on Energi Savr NodeTM with EcoSystem®
Please refer to “Remote Zone Mapping” for important
information.
• DMX channel(s) through DMX output interface
(QSE-CI-DMX). Please refer to “Accessory Controls: DMX
Output Interface”
Zones 1, 2, and 3 can also control the following lighting
sources with a smooth, continuous square law dimming
curve or on a full conduction non-dim basis:
• Incandescent
• Halogen
• Magnetic low-voltage transformer
• Lutron Tu-Wire® electronic fluorescent dimming ballast
• Advance Mark X® electronic dimming ballast
• Neon and cold cathode
• Non-dim (incandescent, magnetic low-voltage, Tu-Wire®,
or neon/cold cathode)
• Cree LR4/6, 120 V
fixtures (for loading capacities,
please refer to the LED report card located at
www.lutron.com/LEDtool)
Please refer to “Capacities” for more information.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Key Design Features
• RF meets FCC Part 15 Class B.
• Lightning strike protection meets ANSI/IEEE standard
62.41-1980. Can withstand voltage surges of up to
6000 V
and current surges of up to 3000 A.
• Tested to withstand 16 kV electrostatic discharge without
damage or memory loss.
• RTISSTM-equipped: Compensates in real time for incoming
line voltage variations (no visible flicker with +/-2% change in
RMS voltage per cycle, and +/-2% Hz change in frequency
per second).
• Power failure memory retains programming and light level
settings for up to 10 years in the event of a power loss.
• The GRAFIK Eye® QS control unit supplies 3 Power Draw
Units (PDUs) on the QS link.
For complete information, see “Power Draw Units on the QS
Link,” Lutron P/N 369405
• Faceplate is hinged at the top and bottom, and stays open
at 180° for ease of access.
• Direct control of 120 V
and 277 V
EcoSystem®,
Hi-lume® 3D, and Hi-lume® LED ballasts (no interface
required).
Page 5
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 6 07.16.12
Specifications
Scene and Shade Buttons
• Large, rounded buttons are easy to use.
• Backlit buttons with optional engraving make it easy to
find and to operate the control unit in low light conditions
(backlight can be disabled).
• Optional button engraving is angled up to the eye for
easy reading.
• Predefined label stickers are included for field labeling.
• 4 preset lighting scenes, plus Off, are accessible from the
front of the control unit.
• 12 additional scenes are stored in the control unit and
are accessible from the integral timeclock, seeTouch® QS
wallstations, and QS interfaces.
• Light levels fade smoothly between scenes. Fade time
can be set differently for each scene: 0 to 59 seconds, or
1 to 60 minutes. Maximum fade time from Scene Off is
3 seconds.
Shade Control
• The GRAFIK Eye® QS control unit can include up to
3 shade button columns. Each column has backlit
open, preset, close, and raise/lower buttons.
• Each shade button column can be programmed to
operate one shade or a group of shades. (Shades may
be assigned to more than one shade button column).
• Faceplates are available with 1, 2 and 3 shade button
columns.
Wireless shade limitations:
• Access to the Sivoia® QS Wireless electronic drive unit
(EDU) is required to associate shades with the GRAFIK
Eye® QS control unit and set their raise/lower limits.
Exception: Sivoia® QS Wireless cellular shades allow limit
setting from the GRAFIK Eye® QS wireless control unit.
• Wired and wireless shades may not be programmed into
the same shade button column; however, both may be
used on the same GRAFIK Eye® QS control unit.
• Scene commands that affect wireless shades across
multiple shade button columns will have a 1-second
delay from column to column. This does not occur in
RadioRA® 2 systems.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Zone Control
• Each zone has a dedicated raise and lower button to adjust
the zone.
• Each zone has a dedicated 7 LED bar graph for level status.
Percentage of light level and energy saved is displayed on
the info screen.
• All zone information has blue backlit LEDs. Backlight turns
off when idle for 30 seconds.
• High-end and low-end trim settings are adjustable per zone
(high end from 99 to 55%; low end from 45 to 1%).
Note: Trim for remote zones must be adjusted locally on the
Energi Savr NodeTM unit.
• Each zone is programmable to only one load type at a time.
Info Screen
• OLED (organic LED) screen is viewable from all angles.
• Screen turns off when idle for 30 seconds.
• Programmable zone labels.
• Programmable scene labels.
• Status of real-time zone percentage and energy savings.
• Programmable timeclock schedules.
• Programmable shade labels.
• Selectable display languages:
- English
- Spanish
- French
- Italian
- German
- Portuguese
Astronomic Timeclock
• Integral to all units.
• 7 daily schedules available.
• One available holiday schedule is programmable by date up
to one year in advance.
• 25 events per day maximum.
• Timeclock events are programmable to control scenes that
affect any Energi Savr NodeTM unit connected on the QS link
without changing the local scene on the GRAFIK Eye® QS
control unit.
• Astronomic times are programmable by integral city
database or by entering latitude and longitude. Sunrise/
Sunset times automatically adjust throughout the year
based on location.
• Automatically adjusts for Daylight Saving Time (DST); DST is
programmable.
• Local timeclock events can activate any of the following features:
- Scenes 1 to 16 and Off
- Any available shade presets
- Start and End afterhours mode
- Enable and Disable daylighting for all zones/groups
- Enable and Disable occupancy for occupancy/vacancy
sensors
- Enable and Disable occupied events for all occupancy
sensors
Page 6
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 7 07.16.12
Specifications
System Communications and Capacities
• Low-voltage type IEC PELV/NEC® Class 2 wiring connects
control units, wallstations, motorized shades, and control
interfaces.
• A QS system can have up to 100 devices and 100 zones.
• A QS system can have up to 30 wireless devices.
• Class 1/Class 2 wiring connects ballast to control unit.
Infrared
• Infrared (IR) receiver allows infrared transmitters to select
8 scenes, raise/lower lighting zones, or raise/lower
shades.
• Transmitter buttons imitate buttons on faceplate.
• 50 ft (15 m) line of sight range.
• Terminal block infrared input for connection to a wired
IR input from third-party equipment.
• IR can be disabled via programming.
• Works with Lutron GRX-IT and GRX-8IT infrared remote
controls.
Accessory Controls: seeTouch® QS Wallstations
(QSWS2)
• Wired seeTouch® QS keypads provide the following
features:
- Access to one or more of the 16 scenes on the
GRAFIK Eye® QS Wireless control unit
- Zone toggle, partitioning, sequencing, fine tune, panic
mode, and timeclock enable/disable
- Contact closure inputs
- Various other functions that are available on specific
wallstation configurations. Refer to the seeTouch®
specification submittal.
Wireless RF Compatibility
• Lutron’s proprietary Clear Connect® RF Technology
• Operates in the 434 MHz band
• Compatible with other Lutron wireless products/systems,
such as:
- Pico® wireless control (P/N PJ-)
- Radio Powr SavrTM occupancy/vacancy/daylight sensors
(P/N LRF2-)
- Sivoia® QS wireless products
- Other GRAFIK Eye® QS wireless control units
(P/N QSGRJ-)
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Accessory Controls: Pico® Wireless Control
(PJ models)
• The Pico® Wireless Control is battery powered. It can
control GRAFIK Eye® QS wireless control units within a
30 ft (10 m) range (60 ft/20 m in open air). It provides the
following features:
- Control of one or more zones on the GRAFIK Eye® QS
Wireless control unit: turns zone(s) on or off, raises/lowers
zone(s), allows programmable light levels for each button,
and goes to user-programmable preset level
- Control of one or more scenes on the GRAFIK Eye®
QS Wireless control unit: the Pico® wireless control can
access any three sequential scenes (1 through 16), or any
two sequential scenes and Off; and can raise and lower
lighting levels.
Note: “Unaffected” is not a valid level for Pico® zone
programming.
Accessory Controls: QS Sensor Module (QSM2)
• The QS Sensor Module provides a means to link wired
or wireless occupancy sensors or daylight sensors, Pico®
controls, and wired infrared sensors to a GRAFIK Eye® QS
control unit via the wired QS link.
- Occupancy sensors wired (or wirelessly linked) to a QS
Sensor Module can be used by one or more GRAFIK
Eye® QS control units on the wired link.
- Daylight sensors wired (or wirelessly linked) to a
QS Sensor Module can be used by one or more GRAFIK
Eye® QS control units on the wired link.
- Pico® wireless controls can control either one or more
zones or scenes on the GRAFIK Eye® QS control unit.
- Pico® wired controls can be used, when connected to
a QS Sensor Module, to control one or more zones or
scenes on the GRAFIK Eye® QS control unit.
- Infrared sensors can control either one or more zones or
scenes on the GRAFIK Eye® QS control unit. Functionality
varies; refer to the documentation for the QS Sensor
Module for details.
Page 7
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 8 07.16.12
Specifications
Accessory Controls: Contact Closure Input/Output
Interface (QSE-IO)
• Recalls preset light levels for the following set of scenes
on the GRAFIK Eye® QS control unit:
Scenes 1-4 and Off Scenes 9-12 and Off
Scenes 5-8 and Off Scenes 13-16 and Off
• Sequence scenes 5-16, Enable/Disable Zone Lockout,
Enable/Disable Scene Lockout, Enable/Disable Panic
Mode, Enable/Disable Timeclock.
• Occupancy Sensors. An individual input counts as 1
occupancy sensor for the GRAFIK Eye® QS control unit.
Each input can be assigned to either Scene Control or
Zone Control (please refer to the Occupancy Sensor(s)
section of this guide).
• Zone Toggle. Allows an input to toggle one or more
zones between programmable preset level(s) and off.
• Shade Output mode. A Shade Column on the GRAFIK
Eye® QS control unit can be linked to control outputs 1-3
and/or outputs 4-5 on the QSE-IO.
Accessory Controls:
DMX Output Interface (QSE-CI-DMX)
• Any zone on the GRAFIK Eye® QS control unit can be
mapped to any single DMX512 Channel.
• Any zone on the GRAFIK Eye® QS control unit can be
simultaneously mapped to any three DMX512 channels
(providing RGB/CMY control).
• DMX loads cannot be used with daylighting.
Accessory Controls: Ethernet and RS232 Interface
(QSE-CI-NWK-E)
• Allows for monitoring and control of the outputs and local
scenes of the GRAFIK Eye® QS control unit.
Accessory Controls: QS Keyswitch Wallstations
(QSWS2-KS)
• Recalls preset light levels for any two scenes including Off
• Allows fine-tuning (raise/lower level) of a zone or group of
zones
• Starts/Stops scene sequencing (Scenes 1-4 or Scenes
5-16)
• Enables/Disables Timeclock
• Enables/Disables occupancy sensors
• Enables/Disabled daylight sensors
• Allows toggle of Zone(s) to a preset level and off
• Enables/Disables panic mode
• Starts/Stops afterhours mode
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
EcoSystem® Ballasts and Devices
• Supports all EcoSystem® ballasts (maximum of 64 ballasts
per GRAFIK Eye® control unit)
• Supports occupancy and daylight sensors wired to a ballast
• Does NOT support IR sensors (or IR keypads) wired to the
ballast
Other Accessory Controls and Devices
• Energi Savr Node® QS (ESN). Refer to the Specification
Submittal for complete details.
Occupancy Sensor(s)
• The GRAFIK Eye® QS control unit works with occupancy
sensors through either:
- Scene Control: Up to four sensors activate user-selectable
occupancy and vacancy scenes.
- Zone Control: up to four sensors per zone activate userselected occupancy and vacancy zone levels.
• Occupancy sensors may include:
- Contact closure sensors wired to CCI input on back of
GRAFIK Eye® QS control unit
- Wireless Radio Powr SavrTM occupancy or vacancy
sensors (model numbers starting with LRF2)
- Wired sensors connected to EcoSystem® ballasts or
interfaces
- Wired or wireless sensors connected to a QS Sensor
Module (QSM)
• If any sensor in a group detects occupancy, then the
GRAFIK Eye® QS control unit will go to the designated
occupancy scene or zone level.
• If all sensors in a group detect vacancy, then the
GRAFIK Eye® QS control unit will go to the designated
vacancy scene or zone level.
• Low battery: the Diagnostics screen will display a low
battery symbol when applicable.
• If the GRAFIK Eye® QS control unit does not receive a signal
from an occupancy sensor on the link (usually due to a
dead battery), the lights associated with that sensor will go
to the occupied level.
Page 8
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 9 07.16.12
Specifications
Daylight Sensor(s)
• The GRAFIK Eye® QS control unit with EcoSystem® works
with compatible daylight sensors to adjust electric light
levels based on measured daylight levels. Sensors can
be configured to control either GRAFIK Eye® QS zones or
groups of EcoSystem® loads independent of zoning.
• Daylight sensors may include:
- Wireless Radio Powr SavrTM (model numbers starting
with LRF2)
- Wired sensors connected to EcoSystem® ballasts or
interfaces
- Wired or wireless sensors connected to a QS sensor
module (QSM)
• In Zone Mode, a daylight sensor can control one or more
GRAFIK Eye® QS zones. Each zone can be calibrated to
target light levels.
- A zone can be controlled by no more than one daylight
sensor
• In Group Mode, a daylight sensor can control one or more
EcoSystem® loads, regardless of how they are zoned on
the GRAFIK Eye® QS control unit.
- A group can be controlled by a single daylight sensor
- Each group can be calibrated to independent target light
levels
- Up to 16 groups are available
• Daylight control can be enabled or disabled on a sceneby-scene basis
- By default, daylight control is enabled in all scenes
Note: Daylight control through the GRAFIK Eye® QS
control unit only affects select lighting loads. Shade
groups cannot be controlled by daylight sensors.
Daylighting does not affect DMX or RGB/CMY DMX loads.
Daylighting of Remote Zones linked to Energi Savr NodeTM
zones must be configured at the Energi Savr NodeTM unit
or through the iPod.
Contact Closure Input (CCI) with Power Supply Output
• Each GRAFIK Eye® QS control unit has one contact
closure input (Terminal A).
- The attached device must provide a dry contact closure
or solid-state output.
- Input is miswire-protected up to 36 V .
• The contact closure is capable of accepting the following
types of inputs:
- Maintained (default): The GRAFIK Eye® QS control unit
will act on both a contact closure and a contact open/
release event.
- Momentary: The GRAFIK Eye® QS control unit will act on
only contact closure events.
• Each GRAFIK Eye® QS control unit can supply 50
mA maximum at 24 V .
- Useful for powering occupancy sensors.
- An auxiliary power supply must be used if the device
requires more than 50 mA.
• The CCI is capable of operating in the following modes
- Occupancy: If an occupancy sensor is wired directly to
the GRAFIK Eye® QS control unit.
- Emergency: This setting allows the GRAFIK Eye® QS
control unit to work with a LUT-ELI. When an emergency
situation is detected, all lights will go to full on, and no
operations will be allowed until the emergency signal is
cleared.
- Afterhours: Allows the CCI to start and end the
afterhours mode.
- Timeclock: Allows the CCI to enable and disable the
timeclock.
- Scene Lockout: Prevents the user from making any
changes to the control unit. The current scene will stay
on until the CCI enables normal operation.
- Save Never: Prevents any changes from being saved
while the CCI is being used.
- Disable CCI: The CCI will have no effect on the system
and will not appear on the list of available sensors.
Security Lockout Password
• A 4-digit password (using characters A to Z and 0 to
9) can be enabled/disabled to lock out access to the
Programming Menu.
• By default there is no password enabled on the GRAFIK
Eye® QS control unit.
• If the 4-digit password is forgotten, contact Lutron
Technical Support to regain access.
iPod is a trademark of Apple Inc. registered in the U.S. and other
countries.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 9
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 10 07.16.12
Specifications
Remote Zone Mapping
• Map a GRAFIK Eye® QS zone directly to an Energi Savr
NodeTM output so that programmed scenes in the
GRAFIK Eye® QS control unit will directly control the
output levels of the Energi Savr NodeTM.
• Adjust high-end and low-end trim for remote zones
through the Energi Savr NodeTM or Energi Savr app
software.
• Change load types of remote zones through the
Energi Savr NodeTM or Energi Savr app software.
• Configure daylighting for remote zones through the
Energi Savr NodeTM or Energi Savr app software.
• Required:
- GRAFIK Eye® QS control unit with firmware version
7.000 or higher
- Energi Savr NodeTM unit with firmware version 6.000 or
higher
- Energi Savr app version 6.0.0 or higher (required only if
the Energi Savr NodeTM unit has been configured using
the app)
Partitioning
• When partition is open, creating one large space,
automatically combines lighting preset functions for
multiple GRAFIK Eye® QS control units.
• When partition is closed, creating two or more smaller
spaces, lighting preset functions become independent.
• Requires one QSWS2-2B wallstation, a GRX-IRPS infrared
transmitter/receiver pair, and a GRX-12VDC power supply
for operation.
• If occupancy sensors are required in a partitioned space,
note that each room’s occupancy sensor(s) will operate
independent of the partition status.
S pecificat ion Sub mitt al
Page 10
®
Job Name:
Job Number:
Model Numbers:
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 11 07.16.12
Capacities
220 - 240 V
Unit Capacity (watts)
MLV
Zone Capacity (watts)
MLV
50 / 60 Hz
120 - 127 V
50 / 60 Hz
3000
2000
3000 VA / 2400 W
2000 VA / 1600 W
40 – 1200
25 – 800
40 – 1200 VA / 40 – 960 W
25 – 800 VA / 25 – 600 W
®
Load Type Notes (Zones 1, 2 and 3)
• All electronic low-voltage (ELV) lighting used with an interface must be rated for reverse phase control dimming. Before
installing an ELV light source, verify with the manufacturer that their transformer can be dimmed. When dimming, an
ELV interface (such as the PHPM-PA-DV-WH) must be used with the control unit.
• Not all zones must be connected; however, connected zones must have a minimum load as specified above.
• Maximum total lighting load for a magnetic low-voltage (MLV) varies by input voltage:
- 120 - 127 V : 800 VA / 600 W
- 220 - 240 V : 1200 VA / 960 W
• Maximum total lighting load for Lutron Tu-Wire® and Advance Mark X® electronic dimming ballasts (120 to 127 V
only) must not exceed 6 A per zone or 16 A per unit.
• No zone may be loaded with more than the capacity specified above. For higher wattage applications, or for 277 V
applications, use Lutron power module PHPM-PA, PHPM-WBX, PHPM-PA-DV, PHPM-SW, or PHPM-WBX-DV.
• For controlling low-wattage loads (CFL, LED) in a non-dim application, contact Lutron Technical Support for the
appropriate solution.
System Limits
• The QS wired communication link is limited to 100 devices or 100 zones.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 11
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 12 07.16.12
GRAFIK Eye® QS Wireless with EcoSystem®
Standard Model Numbers
See following pages for Ordering Custom (Non-Standard) Model Numbers
See Standard Color Combinations page for faceplate, stripe, and button colors
QSGRJ - _ E - _ _ WH
Prefix
White
(standard
color)
EcoSystem®
Number
of Zones
6 = 6 zones
8 = 8 zones
16 = 16 zones
Number
of Shade
Columns
Omit = none
1=1
shade
column
Available Standard Model Numbers
6 Zones
8 Zones
QSGRJ-6E-WH
QSGRJ-8E-WH
QSGRJ-6E-TWH
QSGRJ-8E-TWH
QSGRJ-6E-1WH
QSGRJ-8E-1WH
QSGRJ-6E-1TWH
QSGRJ-8E-1TWH
Top Door
Color
Omit = W
hite
T = Translucent
Example:
QSGRJ-6E-1TWH
6-zone standard white unit with
1 shade column and translucent
top door.
Unit will ship unengraved
with engraving certificate that
customer can redeem at no
charge.
16 Zones
QSGRJ-16E-WH
QSGRJ-16E-TWH
QSGRJ-16E-1WH
QSGRJ-16E-1TWH
Important Note:
For any non-standard units, you must order BOTH a base unit and a Faceplate Kit.
Please see the Custom Ordering Information on the following pages.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 12
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 13 07.16.12
GRAFIK Eye® QS Wireless with EcoSystem®
Custom Color Options and Model Numbers
You must order a Base Unit and a Faceplate Kit
See Standard Color Combinations page for faceplate, stripe, and button colors
Base Unit
Example:
QSGRJ - _ E
QSGRJ-6E
6-zone base unit
and
QSGFP-2IV-EGN
Ivory faceplate kit with two
shade columns and general
engraving
EcoSystem®
Prefix
Number
of Zones
6 = 6 zones
8 = 8 zones
16 = 16 zones
Faceplate Kit
(includes coordinating stripe and buttons)
QSGFP
Faceplate
Prefix
-
-
Number
of Shade
Columns
Omit = none
1 = 1 column
2 = 2 columns
3 = 3 columns
1 9
Color/
Finish
Top
Door
Color
Keypad
Engraving
Code
Omit = s ame as
unit
T = Translucent
2 10
3 11
4 12
5 13
6 14
7 15
1 9
8 16
Faceplate Custom Color/Finish Codes
Architectural Matte
Finishes
Standard
(ship in 48 hours)
White
Ivory
Beige Gray
Brown Black Almond
Light Almond
WH
IV
BE
GR
BR
BL
AL
LA
Architectural Metal
Finishes
Bright Brass
Bright Chrome
Bright Nickel
Satin Brass
Satin Chrome
Satin Nickel
Antique Brass
Antique Bronze
Anodized Aluminum
Finishes
ClearCLA
Black BLA
Brass BRA
®
BB
BC
BN
SB
SC
SN
QB
QZ
Satin Color Matte
Finishes
Job Name:
Job Number:
9-16
1-8
Snow
SW
Biscuit BI
Eggshell
ES
Taupe
TP
MN
Midnight
LimestoneLS
ST
Stone
Desert Stone
DS
TerracottaTC
Hot
HT
GoldstoneGS
PalladiumPD
Plum
PL
TurquoiseTQ
Bluestone
BG
Sea Glass
SG
Greenbriar
GB
Sienna
SI
Merlot
MR
Mocha Stone
MS
S pecificat ion Sub mitt al
Model Numbers:
2 10
Keypad Engraving Codes
3 11
4 12
5 13
6 14
Omit = U
nengraved
OK
Ships with engraving certificate that
customer can redeem at no charge
EGN = General Engraving
1
Open
2
Preset
3
Close
4
Off
Lighting
keypad
Shade
column
NST = N
on-Standard Text Engraving
Please visit the GRAFIK Eye® QS website
at www.lutron.com/grafikeyeqs
for custom engraving forms. Submit
completed form with order, and unit will
ship engraved as specified by customer.
Page
13
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 14 07.16.12
GRAFIK Eye® QS Wireless with EcoSystem®
Custom Options and Model Numbers
See previous pages for Standard and Other Custom Model Numbers
See Standard Color Combinations page for faceplate, stripe, and button colors
Custom Button Kit
QSGB - 5B - WH Custom Button
Kit Prefix
Button
Configuration
3BRL = 3-button with
raise/lower
(shade column)
5B = 5-button
3 11
4 12
1 9
2 10
(lighting keypad)
5 13
Keypad
Engraving
Code
Button
Color/
Finish
6 14
7 15
1 9
8 16
9-16
1-8
Button Kit Custom
Color/Finish Codes
Architectural Matte
Finishes
White
Ivory
Beige Gray
Brown Black Almond
Light Almond
WH
IV
BE
GR
BR
BL
AL
LA
3 11
4 12
5 13
6 14
7 15
8 16
Omit = U
nengraved
OK
Ships with engraving certificate that
customer can redeem at no charge
EGN = General Engraving
Satin Color Matte
Finishes
Snow
Biscuit Eggshell
Taupe
2 10
Keypad Engraving Codes
SW
BI
ES
TP
1
Open
2
Preset
3
Close
9-1
1-8
4
Off
Lighting
keypad
Shade
column
NST = N
on-Standard Text Engraving
Please visit the GRAFIK Eye® QS website
at www.lutron.com/grafikeyeqs
for custom engraving forms. Submit
completed form with order, and unit will
ship engraved as specified by customer.
Custom Stripe Kit
QSGS - WH
Stripe Color/
Finish
Stripe
Kit
Prefix
Stripe Custom Color/Finish Codes
Same as Faceplate colors on previous page
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 14
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 15 07.16.12
GRAFIK Eye® QS Wireless with EcoSystem®
Standard Color Combinations
See previous pages for Standard and Custom Model Numbers
F (faceplate)
S (stripe)
Open
1
Preset
2
Close
3
4
Off
LUTRON
Suffix Faceplate (F)
Architectural Matte
WHWhite
IV
Ivory
BE
Beige
GR
Gray
BR
Brown
BL
Black
AL
Almond
LA
Light Almond
Architectural Metal
BB
Bright Brass
BC
Bright Chrome
BN
Bright Nickel
SB
Satin Brass
SC
Satin Chrome
SN
Satin Nickel
QB
Antique Brass
QZ
Antique Bronze
Anodized
CLA
Clear
BLA
Black
BRA
Brass
®
Stripe (S)
Button (B)
Job Number:
F (faceplate)
Example:
If you order QSGRJ-6E-1WH, your GRAFIK
Eye® QS with 6 lighting zones and 1 shade
column will come with a white faceplate
(both top and bottom), gray stripe, and white
buttons.
Suffix Faceplate (F) Stripe (S)
Satin Matte
MN
Midnight
Gray
Gray
White
Beige
Ivory
TPTaupe
Gray
Ivory
Beige
SWSnow
Gray
Black
Gray
ES
Eggshell
Beige
Black
Brown
BI
Biscuit
Eggshell
Gray
Black
LS LimestoneGray
Light Almond Almond
STStone
Gray
Almond
Light Almond DS
Desert Stone Taupe
TCTerracottaTaupe
Black
Black
BG
Bluestone
Gray
Black
HTHot
Black
Taupe
Black
Black
MRMerlot
Taupe
Black
Black
SI
Sienna
Brown
Black
Black
GB
Greenbriar
Gray
Black
Black
SG
Sea Glass
Gray
Black
MS
Black
Mocha Stone Taupe
Black
Black
GSGoldstoneIvory
PDPalladium Gray
Black
Black
PLPlum
Taupe
TQTurquoise Gray
Black
Black
Black
Black
S pecificat ion Sub mitt al
Job Name:
B (buttons)
Faceplate is comprised of a top and bottom.
The bottom will always be the color indicated
under “faceplate.” The top may be the
same color or translucent. Use the chart for
faceplates that have the same color top and
bottom. If a translucent lid is chosen, the
stripe will automatically be the same color as
the bottom lid.
Model Numbers:
Button (B)
Black
Taupe
Snow
Eggshell
Biscuit
Gray
Gray
Taupe
Taupe
Gray
Taupe
Taupe
Brown
Gray
Gray
Taupe
Ivory
Gray
Taupe
Gray
Page 15
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 16 07.16.12
Overview
Terminations
Load wiring
EcoSystem® bus (E1, E2)
Communication link
Occupancy sensor/contact closure input
and 24 V
power
IR input
Wire Gauge
12 AWG (4.0 mm2)
14 AWG (2.5 mm2)
16 AWG (1.5 mm2)
18 AWG (1.0 mm2)
®
Maximum EcoSystem®
Bus Length
2200 ft (671 m)
1400 ft (427 m)
900 ft (275 m)
570 ft (175 m)
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 16
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 17 07.16.12
Power Group Wiring Example
On the QS link, there are devices that supply power and devices that consume power. Each device has a specific
number of Power Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that
supplies power and one or more devices that consume power; each Power Group may have only one power-supplying
device. Refer to the QS Link Power Draw Units specification submittal (Lutron P/N 369405) for more information
concerning PDUs.
Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram.
Between devices on the QS link that supply power, connect only terminals 1, 3, and 4 (NOT terminal 2), shown by the
letter B on the diagram.
Wiring can be T-tapped or daisy-chained.
A
Power Group 1
LUTRON
GRAFIK Eye® QS
control unit
Supplies PDUs
A
LUTRON
B
Control Interfaces
Consume PDUs
(Do not connect
terminal 2: 24 V )
Wallstations
Consume PDUs
Power Group 2
A
Connect all 4
terminals within a
power group:
1: Common
2: 24 V
3 and 4: Data
B
LUTRON
Energi Savr NodeTM QS
unit Supplies PDUs
LUTRON
Connect only 3
terminals between
power groups:
1: Common
3 and 4: Data
Do not connect
Terminal 2: 24 V
LUTRON
Wallstations
Consume PDUs
B
(Do not connect
terminal 2: 24 V
)
Power Group 3
A
Wireless Occupancy Sensor
does not consume PDUs
QS Power Supply
Supplies PDUs
LUTRON
Control Interfaces
Consume PDUs
Wallstations
Consume PDUs
B
(Do not connect
terminal 2: 24 V )
®
Quantum® processor
Supplies PDUs
S pecificat ion Sub mitt al
Job Name:
Job Number:
QS Sensor Module with
wired Occupancy Sensor
Consumes PDUs
Model Numbers:
Page 17
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 18 07.16.12
Line Voltage Wiring
}
Do not use
Rear of
QS control unit
To Load 1
Line voltage (hot/live)
is labeled L.
To Load 2
To Load 3
Loads 1, 2, 3,
120-127 V
or
220-240 V
1 2 3 4 5 6 L N
120-127 V
or
220-240 V
Distribution Panel
• Pull power wiring from distribution panel and to light fixtures.
• Each line voltage terminal can accept one 12 AWG (4.0 mm2) wire.
• Consult Lutron for non-dim relay wiring and/or load side emergency transfer wiring.
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 18
3
2
1
4
4
Wireless Control 3Unit with EcoSystem®
3
2
2
1
Preset Dimming Controls
1
369314c 19 07.16.12
EcoSystem® Bus Wiring
4
3
2
1
4
3
EcoSystem® Bus Link Terminal Detail
2
1
1 2 3 4 5 6 L N
4
3
2
1
E2
E1
EcoSystem®
ballasts
E2
E1
To additional EcoSystem®
ballasts
EcoSystem® Bus Wiring Example
To additional ballasts and
modules (up to 64 total)
EcoSystem® Bus
EcoSystem®
Ballast
LUTRON
GRAFIK Eye® QS
with EcoSystem®
(limit one per
EcoSystem® link)
®
EcoSystem®
Module
Occupancy
Sensor
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Eco-10® or
Hi-lume®
Ballast
EcoSystem®
Ballast
EcoSystem®
Ballast
Daylight Sensor
Page 19
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 20 07.16.12
IEC PELV/NEC® Class 2 QS System Wiring
• Wiring can be daisy-chained or T-tapped.
• Wiring must be run separately from line/mains voltage.
• Total length of control link must not exceed 2000 ft (610 m).
Wire Sizes (check compatibility in your area)
QS Link Wiring Length
Wire Gauge
Less than 500 ft (153 m)
Power (terminals 1 and 2)
1 pair 18 AWG (1.0 mm2)
Lutron Cable Part Number
GRX-CBL-346S (non-plenum)
GRX-PCBL-346S (plenum)
Data (terminals 3 and 4)
1 twisted, shielded pair 22 AWG (0.5 mm2)
500 to 2000 ft
(153 to 610 m)
Power (terminals 1 and 2)
1 pair 12 AWG (4.0 mm2)
GRX-CBL-46L (non-plenum)
GRX-PCBL-46L (plenum)
Data (terminals 3 and 4)
1 twisted, shielded pair 22 AWG (0.5 mm2)
Daisy-Chain Wiring Example
GRAFIK Eye® QS
Control Unit
seeTouch® QS
wallstations
Sivoia® QS
Shade
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
Sivoia® QS
smart panel
LUTRON
LUTRON
LUTRON
LUTRON
T-Tap Wiring Example
GRAFIK Eye® QS
Control Unit
seeTouch® QS
wallstations
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
Sivoia® QS
smart panel
Sivoia® QS
Shade
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 20
Wireless Control Unit with EcoSystem®
Preset Dimming Controls
369314c 21 07.16.12
Mounting
Fits into a 4-gang
U.S. backbox,
3` in (90.4 mm) deep
(Lutron P/N 245-254)
or
3 in (76.2 mm) deep
(Lutron P/N 241-400)
Hinged
top lid
Mounting
screws (4)
GRAFIK Eye®
QS with
EcoSystem®
control unit
Hinged
bottom lid
®
S pecificat ion Sub mitt al
Job Name:
Job Number:
Model Numbers:
Page 21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising