Features PremiSys™ Two-Reader Controller

Features PremiSys™ Two-Reader Controller
Features
• The Two-Reader Controller connects to the PremiSys system
components listed below. A mix of up to 32 of these hardware
components, connected using one port via two-wire RS-485,
is possible:
~~ The Input Board provides 16 supervisable inputs
The Two-Reader Controller is an intelligent controller for
IDenticard® PremiSys™ access control. With an onboard
Ethernet port, two reader ports and increased memory, the
Two-Reader Controller is a cost-effective access control
solution for any size application, from single-controller
installations to applications requiring scores of controllers.
Once the system databases are loaded into the controller
memory, the Two-Reader Controller can perform interface
and management functions without dependence on a host
computer.
Communications with the host PC are selectable at the time
of installation: TCP/IP via an onboard Ethernet port or serial
RS-232. Communications with other system boards such
as Input, Output and Reader Boards are two-wire RS-485.
The Two-Reader Controller can connect to a maximum of 32
Reader, Input and Output Boards in any combination using
two-wire RS-485 (4,000 feet / 1219 m maximum cable length
per run). Standard communication speed is 38,400 baud;
however, baud rates are selectable and range from 2,400
to 115,200, depending on system, network, computer and
other hardware characteristics.
~~ The Output Board provides 16 Form C, SPDT output relays
~~ The One- or Two-Reader Boards are used with all readers
in the PremiSys system. A maximum of 64 reader ports
can be utilized, including the two on the controller.
• The Two-Reader Controller includes the following components
and features:
~~ A primary port featuring onboard Ethernet
~~ An alternate port for RS-232 communications, allowing
redundancy to the host in the event that the primary
host-communications link is lost
~~ Two reader ports
~~ Four relays configurable for normally open or normally closed
operation
~~ Eight general-purpose input points that can be supervised or
not to serve as door-input points, request-to-exit points, etc.
~~ Two dedicated input points for monitoring power loss to the
board and enclosure tampering
~~ 17 MB memory including 16 MB non-volatile flash memory for
card and system information and 1 MB SRAM for transactions
and new card information
~~ 16 MB SDRAM for system firmware and database storage for
the application
~~ LEDs to indicate controller status
~~ A DIP switch for Web browser communication to the controller,
for the purpose of configuring the communication parameters
~~ A 3-volt lithium coin cell that provides RAM and clock backup
• The Two-Reader Controller is to be housed in a wall-mounted
enclosure that can contain other PremiSys components as well. The
Two-Reader Controller can be wired to alert system operators if the
enclosure is tampered with. An optional lock for the enclosure door
is available.
• The Two-Reader Controller is rated for Class 2 low-voltage
applications. IDenticard®-approved 12 VDC power supplies are
available. A relay on this power supply can be wired to provide a
power-loss alert. Optional backup power can be provided by a
12-volt battery connected to the power supply.
• Firmware for the Two-Reader Controller is FLASH upgradeable.
PremiSys™
Two-Reader Controller
PREM-CTLR2RDR
PremiSys™ Two-Reader Controller
Specifications
Controller Certifications
Options and Accessories
One-Reader Board | PREM-BRD1RDR
This board can connect to one reader and provides two input points and
two relays. The One-Reader Board’s reader port supports connection to ABA
and Wiegand format readers in a wide variety of reader types, including
smart card and biometric readers, as well as keypads.
Two-Reader Board | PREM-BRD2RDR
This board can connect to two readers and provides eight input points and
six relays. The Two-Reader Board’s reader ports support connection to ABA
and Wiegand format readers in a wide variety of reader types, including
smart card and biometric readers, as well as keypads.
UL: UL 294 recognized: Access Control System Units - component
CE Compliant, FCC Part 15 Class A, NIST Certified Encryption
Dimensions and Weight
Controller Width
Controller Height
Controller Depth
Controller Weight
Environmental Specifications
Temperature
Relative Humidity
CAUTION! The processor in this component is intended for use only in a Class 2,
low-voltage circuit.
Two-Reader Controller
Input Voltage
Output Board | PREM-BRDOUT
One Output Board provides 16 output relays. Relays typically are used for
door and elevator control as well as for general facility control.
Relay Rating
(each of four relays)
Card Reader Power
(each of two readers)
Large Enclosure | PREM-ENCLG
The Large Enclosure has eight positions available for a controller and/or
other boards and/or power supply.
Small Enclosure | PREM-ENCSM
The Small Enclosure can hold one controller, board or power supply.
PremiSys™ Altronix® Ten-Amp P/S with Eight Isolated Outputs
Power Supply | PREM-PS10ALT
This power supply/controller module is rated at 12 VDC and 10 Amps
supervised (AC & battery). It accepts 115 VAC 60 Hz 1.9 Amp input voltage,
has eight power-limited outputs and is UL Listed for Access Control System
Units (UL 294). This power supply features eight independently controlled
fail-safe and/or fail-secure power outputs.
32°F to 158°F (0°C to 70°C) operating
-67°F to 185°F (-55°C to 85°C) storage
0 to 95% RH noncondensing
Power Specifications
Input Board | PREM-BRDIN
One Input Board provides 16 supervised input points and two relays.
Eight-Channel MUX Board | PREM-BRD8MUX
The MUX Board is a multiplexer that expands a single communications
channel on a controller into multiple data channels for connection to I/O
boards in the system. Common uses are for star-topology wiring
arrangements or home-run wiring.
8.0 inches (203 mm)
6.0 inches (152 mm)
1.0 inch (25 mm)
9 ounces (255g) (nominal)
RAM and Clock Backup
12-24 VDC ± 10%, 500 mA maximum (reader current not
included)
12 VDC @ 250 mA (plus reader current) nominal
24 VDC @ 150 mA (plus reader current) nominal
5 A at 30 VDC
12 VDC (10.8-13.2 VDC) ± 10% nominal or
unregulated, current limited to 150 mA for each reader
OR
12 to 24 VDC ± 10% (pass-through voltage) current
limited to 125 mA for each reader
Lithium coin cell, 3.0 V, type BR2325, BR2330, CR2330
Wiring Specifications
Power to Two-Reader
Controller
Primary – Ethernet-to-Host
Port 1 (alternate) – RS-232
to Host or Ethernet to Host
via separate Network Card
Ports 2
Twisted pair, 18 AWG (0.823 mm2)
Ethernet: Category 5 cable
RS-232: Twisted pairs, 22 AWG (0.325 mm2), with overall
shield. Maximum cable length: 25 feet (7.6 m)
Twisted pairs, 22 AWG (0.325 mm2), with shield. Maximum
cable length: 4000 feet (1219 m) of wire, total
copper, including drops
Use wire and gauge as required by load
Connection to RelayControlled Devices
Connection to Input-Point One twisted pair per input, 30 ohms maximum
Devices
Connection to Readers
Refer to the reader manufacturer specifications for
cabling requirements. Maximum cable length: 500 feet
(150 m), total copper, including drops
Alarm Inputs
Twisted pair, 30 ohms maximum
Communications Specifications
Primary Port
Port 1 (alternate port)
Port 2
Ethernet: 10/100Base-T interface up to 115,200 bps
RS-232: 9600; 19,200; 38,400 or 115,200 bps
Two-wire RS-485: 2400 to 38,400 bps
Access Control Specifications
Inputs – Dedicated
Inputs – Assignable
Relays
Relay Contact Type
Relay Configuration
SRAM Capacity
SDRAM Capacity
Flash Memory Capacity
Two unsupervised, dedicated alarm inputs for enclosure
tamper and power loss
Two supervised, end-of-line (EOL) resistors, 1K/2K ohm
1% ¼ watt standard
Two supervised, end-of-line (EOL) resistors, 1K/2K ohm
1% ¼ watt standard
Form C
Single-pole double-throw (SPDT)
1 MB battery-backed
16 MB
16 MB
Indicators
Visible
25 Race Avenue, Fl. 1 • Lancaster, PA 17603
TEL 855.367.4721 • 717.295.8039 • FAX 717.427.1654 • www.IDenticard.com
All brand and product names mentioned may be trademarks or registered trademarks of their respective
companies in the United States and/or other countries. See current IDenticard® price list or other product
documentation for warranties and limits of liability. Copyright ©2015 IDenticard Systems Worldwide, Inc.
All rights reserved. Rev. 9/15
19 red, single-color LEDs
2 LEDs for Ethernet connection, one green, one yellow
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising