63-1228—06 - M6410A,M7410F,M6435A,M7435F

63-1228—06 - M6410A,M7410F,M6435A,M7435F
M6410A,M7410F,M6435A,M7435F Actuators
V5852A, V5853A, V5862A, V5863A Valves
40.5 LB (180N) NON-SPRING/SPRING RETURN ACTUATORS
AND 1/2 INCH, 3/4 INCH CARTRIDGE GLOBE VALVES
SPECIFICATION DATA
M6410A and M7410F Series 1000 Non-Spring Return Valve
Actuators provide floating or modulating control of Series
1000 and 2000 V5852A, V5853A, V5862A and V5863A
Cartridge Globe Valves.
Spring Return (M6435A, M7435F)
M6435A and M7435F Series 1000 Spring Return Valve
Actuators provide floating or modulating control of Series
1000 and 2000 V5852A, V5853A, V5862A and V5863A
Cartridge Globe Valves.
Valves
The actuators are used in electronic temperature control
systems, which use hot and/or cold water (with glycol up to
50 percent) as the controlled medium in variable air volume
(VAV) terminal units, fan-coil units, small reheaters and
recoolers.
The V5852A, V5853A, V5862A, V5863A Series 1000 and
2000 Cartridge Globe Valves can also be controlled by
MP958A Pneumatic Valve Actuators.
FEATURES
• Small size allows installation in limited space.
• Long stroke allows wider range of control.
Actuators
•
•
•
•
•
•
•
Low power consumption.
Synchronous motor.
No mounting tools required (including the MP958).
Low-maintenance plastic housing.
Conduit connector standard.
No separate linkage required.
M64XXA provides 3-position floating control without
proportional feedback.
• M74XXF receives 0 to 10 Vdc or 2 to 10 Vdc input
signal, selectable at the site.
• M74XXF includes direct/reverse acting switch.
Non-Spring Return (M6410A, M7410F)
• Especially suitable for Excel® Controller or Individual
Room Controller (IRC) System.
• Internal valve position indicator.
• Magnetic coupling for torque limitation independent of
voltage supply, and self-adjustment of close-off port.
• Ready-to-wire connecting cable.
• Force-limiting end switches.
• No calibration required.
•
•
•
•
•
•
V5852A is a two-way female sweat valve.
V5853A is a three-way female sweat mixing valve.
V5862A is a two-way female NPT valve.
V5863A is a three-way female NPT mixing valve.
Soft valve seat provides low leakage rate.
Valve inserts are changeable without draining valve
when used with the insert replacement tool.
• Threaded plastic cover allows manual operation.
• Brass body and stainless steel stem.
SPECIFICATIONS
CAUTION
Equipment Damage Hazard.
Installing a high-force (67.5 lb [300 N]) actuator on
1/2 or 3/4 in. valve can damage the valve beyond
repair.
Use only Series 1000 (40.5 lb [180 N]) actuators with
these smaller (1/2 in. and 3/4 in.) valves.
IMPORTANT
— Complete valve body soldering (V5852, V5853)
before installing cartridge inserts.
— Install low-force actuators (40.5 lb) only on small
valves (1/2 in., 3/4 in.).
Models:
 M6410A: Non-Spring Return Valve Actuator. Provides
floating control of the V5852A, V5853A, V5862A, V5863A
Valves.
 M6435A: Spring Return Valve Actuator. Provides floating
control of V5852A, V5853A, V5862A, V5863A Valves.
Stem retracts upon power failure.
 M7410F: Non-Spring Return Valve Actuator. Provides
modulating control of V5852A, V5853A, V5862A, V5863A
Valves.
 M7435F: Spring Return Valve Actuator. Provides
modulating control of V5852A, V5853A, V5862A, V5863A
Valves. Stem retracts upon power failure.
63-1228-06
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES




 M7410F: 0 to 10 Vdc or 2 to 10 Vdc Electronic Actuator, or
 M7435F: Spring Return Valve Actuator (modulating
control; stem retracts upon power failure).
 MP958: Pneumatic Valve Actuator.
 Valve inserts are provided as spare parts. See Table 2.
V5852A: Two-way Sweat Valves.
V5853A: Three-way Sweat Mixing Valves.
V5862A: Two-way NPT Valves.
V5863A: Three-way NPT Mixing Valves.
Control Modes:
 M6410A, M6435A: Floating.
 M7410F, M7435F: Modulating.
Rangeability:
 Two-way Valve: 100:1.
 Three-way Valve: 50:1 for controlled port (A to AB).
Ambient Ratings:
 Operating Temperature Range: 32° to 122°F (0° to 50°C).
 Storage Temperature Range: -40° to 158°F (-40° to 70°C).
 Humidity Range: 5 to 95% RH (noncondensing).
Flow Characteristic:
 V5853, V5863:
 A to AB: Equal Percentage.
 B to AB: Linear.
 V5852, V5862: Equal percentage.
Electrical Ratings:
 Input Power:
 M6410A, M7410F: 24 Vac, +10/-30 percent, 50/60 Hz.
 M6435A, M7435F: 24 Vac, +20/-15 percent, 50/60 Hz.
 Power Consumption:
 M6410A: 0.7 VA.
 M7410F: 1.4 VA.
 M6435A: 10 VA.
 M7435F: 5 VA.
 Input Signal (M7410F, M7435F): Modulating 0 to 10V,
2 to 10V (adjustable), 0.1 mA.
 Input Impedance (M7410F, M7435F): 100K ohms.
Valve Cv Rating:
 See Table 1.
NOTE: To determine the capacity index (Cv) needed for
your application, use the following formula: Cv =
gallons per minute divided by the square root of
the pressure drop across the valve when the
valve is fully open.
Valve Close-off Ratings:
 See Table 1.
Mounting:
 Actuator screws onto valve body.
Body Material:
 Yellow Brass:
Connections:
 M6410A, M7410F: 4.9 ft (1.5m) cable.
 M6435A, M7435F: 1.5 sq mm terminals.
Stem and Plug Assembly:
 Stem: Stainless steel.
 Plug: Brass.
Weight:
 M6410A: 5 oz (0.15 kg).
 M7410F: 5.6 oz (0.16 kg).
 M6435A, M7435F: 17.6 oz (0.5 kg).
Table 1. Valve Close-off Ratings.
Pipe Size in
in. (mm)
Stroke:
 1/4 in. (6.5 mm).
1/2 (13)
Running Time:
 At 50 Hz:
 M6410A, M7410F: 150 seconds.
 M6435A, M7435F: 60 seconds.
 At 60 Hz:
 M6410A, M7410F: 125 seconds.
 M6435A, M7435F: 50 seconds.
Two-way
0.2
232
0.3
232
Three-way
116
0.5
3/4 (19)
0.7
232
1.2
174
1.9
174
2.9
58
36
34b or 15c
4.6
Spring Return Time:
 10 seconds.
a The
Cv for the bypass port (B) on all three-way valves is
reduced by one Cv level. Example: A Port Cv = 0.5;
B Port Cv = 0.3 with the load matched to the proper Cv.
b For V5853A1XXX and V5863A1XXX Valves (Series 1000).
c For V5853A2XXX and V5863A2XXX Valves (Series 2000).
Stem Force:
 40.5 lb (180 N).
Suitable Medium:
 Water with maximum 50% glycol.
IMPORTANT
Mount all valve types in return flow. When delta pvalues exceed 8.70 psi (60 kPa), noise can develop.
Controlled Water Temperature:
 36° to 230°F (2° to 110°C).
Leakage Rate:
 <0.02% of Cv.
Approvals (Actuators):
 Underwriters Laboratories Inc. listed for plenum use
(UL94-5V).
Actuator Required:
 M6410A: Non-Spring Return Valve Actuator (3-position
floating).
 M6435A: Spring Return Valve Actuator (3-position floating;
stem retracts upon power failure).
63-1228—06
Close-off Rating (psi)
Cva
Accessories and Replacement Parts:
 WV108B Brush Tool for valve seat cleaning (used with
WV108M tool).
2
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES
 WV108M Insert Replacement Tool, for replacing cartridge
insert without draining system.
Table 2. Valve Insert Replacement Parts.
Diameter
(in.)
For Valve
Cv
Part
Number
Interchangeable With
Two-Way
1/2
3/4
V5852A2007, V5862A2005
0.2
0902812
0902809, 0902810, 0902811
V5852A2015, V5862A2013
0.3
0902811
0902809, 0902810, 0902812
V5852A2023, V5862A2021
0.5
0902810
0902809, 0902811, 0902812
V5852A2031, V5862A2039
0.7
0902809
0902810, 0902811, 0902812
V5852A2049, V5862A2047
1.2
0902808
0902807
V5852A2056, V5862A2054
1.9
0902807
0902808
V5852A2064, V5862A2062
2.9
0902814
0902815
V5852A2072, V5862A2070
4.6
0902815
0902814
Three-Way
1/2
3/4
V5853A2006, V5863A2004
0.3
0902821
0902822, 0902823, 0902824
V5853A2014, V5863A2012
0.5
0902822
0902821, 0902823, 0902824
V5853A2022, V5863A2020
0.7
0902823
0902821, 0902822, 0902823
V5853A2030, V5863A2038
1.2
0902824
0902821, 0902822, 0902824
V5853A2048, V5863A2046
1.9
0902825
None
V5853A2055, V5853A1008,
V5863A1006, V5863A2053
2.9
0902827
None
V5853A2063, V5853A1016,
V5863A1014, V5863A2061
4.6
0902827
None
M8286
3
63-1228—06
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES
TYPICAL SPECIFICATION
Dimensions in in. (mm):
4-1/4 (108)
Cartridge Globe Valves
3-3/16 (81)
Cartridge globe valve supplier must be Honeywell.
Valves shall be available in two- and three-way
mixing models with brass bodies and stainless
steel stem. Valves must have nominal rangeability
of 50:1 or better. Valves must have a leakage rating
less than 0.02% of the Cv.
1-5/16
(33)
5
(126)
Valves shall be usable with hot water, chilled water,
or glycol solutions up to 50 percent. Valves must
have available insert replacement tools to facilitate
changing the cartridge without draining the valve.
Cartridge Globe Valve Actuators
M19615
Cartridge globe valve actuator supplier must be
Honeywell. Electric actuators shall provide either
floating or modulating control of two- and threeway cartridge globe valves. Actuator will operate
at 24 Vac (+10/-30%) and 50/60 Hz. Actuator must
screw onto compatible valve body without the aid
of mounting tools. Actuator must be available in
both spring return and non-spring return models.
Actuators shall have an ambient temperature
rating of 32 to 122 degrees Fahrenheit.
Spring Return Actuators (M6435A, M7435F)
2-5/16 (58)
3-15/16
(100)
1/2 (13)
2-3/8 (61)
1-15/16
(49)
M8225A
Non-Spring Return Actuators
(M6410A, M7410F)
1/4 STROKE
(7)
V5852/V5862
FLOW DIAGRAM
1-3/16 (30)
23/32
(18)
INLET
OUTLET
VALVE
SIZE
A
B
(NPT)
C
D
(NPT)
D
(SWEAT)
1/2 (13)
2-1/3 (60)
1/2 NPT
1-1/3 (34)
1/2 NPT
5/8 (16)
3/4 (19)
3-2/9 (82)
3/4 NPT
1-1/4 (32)
3/4 NPT
7/8 (22)
C
D
E
(SWEAT)
1/2 (13) 2-1/2 (63) 5/6 (21) 1-1/4 (32)
3/4 (19) 3-2/9 (82)
C
B
B
D
A
1/4
(7) STROKE
V5853/V5863
FLOW DIAGRAM
1-3/16 (30)
23/32
(18)
PORT AB
PORT A
D
B
B
B
A
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
VALVE
SIZE
A
B
NPT
1-1/3 (34)
5/8 (16)
1 (27)
1-3/5 (41)
1-2/7 (33)
7/8 (22)
B
NPT
C
D
E
(NPT)
1/2 (13) 2-5/7 (69) 1/2 NPT 1-1/4 (32)
1-1/3 (34)
1/2 NPT
3/4 (19) 3-2/9 (82) 3/4 NPT 1-3/5 (41)
1-2/7 (33)
3/4 NPT
V5863 (NPT)
E
C
V5853 (SWEAT)
PORT B
VALVE
SIZE
A
NOTE: SOLDER ENDS CONFORM TO ANSI B16-18.
M34543
By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising
out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and
subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees, arising out of, or
resulting from, any modification to the literature by you.
® U.S. Registered Trademark
© 2013 Honeywell International Inc.
63-1228—06 M.S. Rev. 04-13
Printed in United States
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising