Horizon Hobby SPEKTRUM DX6i Transmitter

Horizon Hobby SPEKTRUM DX6i Transmitter
EN
®
Physical Transmitter Adjustments
Transmitter Mode Conversion
You can change transmitter modes between Mode 1 and Mode 2. This conversion requires both a
programming and a mechanical change.
Programming set up:
1. Power on the transmitter.
2. Press the roller, scroll to Setup List and press the roller to access the Setup List.
3. Select Copy/Reset in the Setup List. When the Copy/Reset menu screen opens, select Reset.
4. Move the Aileron D/R switch forward and backward FOUR TIMES. A screen will display Mode 1 and Mode 2.
5. Select the desired mode.
6. After you change the transmitter Mode in the Setup List, you will need to make
mechanical changes to the transmitter gimbals.
X4
CAUTION: Always power off the transmitter and remove the batteries before adjusting stick tension
or friction straps. Not doing so could result in property damage or injury.
Mechanical Conversion:
Mechanical conversion is required to change between Modes 1 and 2. The mechanical conversion
consists of the following steps:
• Removing the
• Changing the
• Adjust the Elevator
rear case
Throttle Ratchet
Centering Screw
Removing the Rear Case:
1. Power off the transmitter and remove the transmitter batteries.
2. Remove the six Phillips head screws that secure the rear transmitter case half.
3. Put the transmitter face down on a piece of foam or a towel and remove the rear case.
Throttle Friction Straps
CAUTION: Use care to not pull or disconnect any of the wires attached to the back
transmitter half.
Changing the Throttle Ratchet:
1. Locate the silver throttle friction straps on both gimbals.
2. To change the throttle ratchet, loosen the throttle strap so it does not touch the throttle gimbal. Tighten the
opposite throttle strap to engage the desired throttle ratchet.
Adjusting the Elevator Centering Screw:
When changing between Modes 1 and 2, you must adjust the elevator centering screw.
1. Hold the Elevator or Throttle stick in the full up or full down position when you are adjusting the elevator
centering screw. Holding the gimbal stick reduces the load on the elevator centering mechanism and makes
it easier to adjust the centering screw.
2. Locate the gimbal where the elevator centering spring is engaged. Use a Phillips screwdriver to tighten the
elevator centering screw. Tightening the screw will disengage the centering spring.
3. Using a Phillips screwdriver, loosen the opposite elevator centering screw until the lever engages.
Elevator Centering
Screw
Stick Tension
Adjustment Screws
Adjust Stick Tension
With the rear of the transmitter case off you can adjust the stick tension.
1. Locate the gimbal tension adjustment screws located on each axis of each gimbal. Turn the desired
screws a small amount using a small Phillips screwdriver.
2. Locate the silver throttle friction straps on the throttle gimbal. One strap engages a serrated section on
the gimbal for a ratcheted throttle, while the other strap engages the smooth section on the gimbal.
Use a small Phillips screwdriver to tighten or loosen the screw for the friction strap.
NOTICE: Always do a test of stick tension while turning these screws to ensure stick tension is not too
loose or too tight. Tightening a screw too much can damage a spring. Loosening a screw too much can let a
spring fall off and cause a short-circuit in the transmitter.
Friction
Re-assembling the Transmitter
1. Put the rear of the transmitter case on, taking care to not pinch any wires.
2. Install and tighten the six Phillips screws.
3. Reinstall the batteries.
Ratchet
IMPORTANT: Your Spektrum DX6i transmitter includes 4 AA Alkaline batteries to power the transmitter. If you wish to use rechargeable batteries in your transmitter, Spektrum offers
optional rechargeable AA batteries (SPM9527) and a charger (SPM9551). NEVER attempt to charge alkaline batteries.
EN
Compliance Information for the European Union
AT
EE
IE
PL
IS
BE BG
ES FI
IT LT
PT RO
LI NO
CZ CY DE DK
FR GR HR HU
LU LV MT NL
SE SI SK UK
CH
Declaration of Conformity
Instructions for disposal of WEEE by
users in the European Union
(in accordance with ISO/IEC 17050-1)
No. HH2014040701
Product(s):
SPM DX6i 6CH Transmitter System and Transmitter Only
Item Number(s):
SPM6630, SPMR6630
Equipment class:
2
The object of declaration described above is in conformity with the requirements of the
specifications listed below, following the provisions of the European R&TTE Directive
1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC:
EN 300-328 V1.7.1: 2006
EN 301 489-1 V1.9.2: 2012
EN301 489-17 V2.1.1: 2009
This product must not be disposed of with other waste.
Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated
collections point for the recycling of waste electrical
and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information
about where you can drop off your waste equipment for recycling,
please contact your local city office, your household waste disposal
service or where you purchased the product.
EN60950-1:2006+A11:2009+A1:2010+A12: 2011
EN55022:2010 + AC:2011
EN55024:2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
Signed for and on behalf of:
Horizon Hobby, LLC
Champaign, IL USA
April 7, 2014
Robert Peak
Chief Financial Officer
Horizon Hobby, LLC
©Horizon Hobby, LLC. DSMX is a registered trademark of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Created 3/14 44094
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising