FortiGate-311B QuickStart Guide

FortiGate-311B QuickStart Guide
LED
Power
Status
State
Description
Green
The FortiGate unit is on.
Off
The FortiGate unit is off.
QuickStart Guide
FortiGate-311B
Green
Flashes during startup
Off
The FortiGate unit is running normally.
Green
The FortiGate unit is running in HA mode.
Off
The FortiGate unit is not in HA mode.
Alarm
Off
The FortiGate unit is running normally. LED not used.
Left LED
Ports 1 to 10
Green
The correct cable is in use and the connected equipment has power.
Off
No network cable connected.
Green
Network speed of 1000 Mbps.
Amber
Network speed of 100 Mbps.
Off
Network speed of 10 Mbps.
HA
Right LED
Ports 1 to 10
NP2 Powered
311B
STATUS
ALARM
1
POWER
HA
1/2
3/4
7/8
5/6
USB
9/10
ASM
CONSOLE
Visit these links for more information and documentation for your Fortinet product.
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class A Part 15 CSA/CUS
25 May 2009
• Technical Documentation - http://docs.forticare.com
• Fortinet Knowledge Center - http://kc.forticare.com
• Fortinet Technical Support - http://support.fortinet.com
01-30007-97512-20090525
Package Contents
Connector
Type
Speed
Protocol
Description
Ports 1 to 10
RJ-45
10/100/1000
Base-T
Ethernet
10-port connection to up to ten devices or the internal network.
CONSOLE
RJ-45
9600 bps 8/N/1
RS-232 serial
Optional connection to the management computer.
Provides access to the command line interface
USB
USB
USB
Optional connection for USB key for firmware
backup and installation.
Front
Status LEDs
Power LED
QuickStart Guide
10 port Ethernet
network connection
RJ-45 serial
connection
USB
FortiGate-311B
AMC
single-width
module slot
Rack-Mount
Brackets
NP2 Powered
311B
1
Tools and Documenation
STATUS
ALARM
POWER
HA
1/2
3/4
5/6
7/8
9/10
USB
ASM
CONSOLE
NP2 Powered
Copyright 2009 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
311B
STATUS
ALARM
1
POWER
HA
1/2
3/4
5/6
7/8
9/10
USB
ASM
CONSOLE
4 Rubber feet
Back
Welcome | Bienvenue | Willkommen | ᱑ㄫ | Bienvenido | Benvenuto
64 GB SSD
HDD1
Ground
HDD2
FSM slots
PWR 1
PWR 2
2 AC Power Cables
AC power
connections
Straight-through
RJ-45 to
Ethernet cable DB-9 Serial Cable
Connecting
Connect the following to the FortiGate unit. Ensure the FortiGate unit is placed on a stable
surface.
•
Affix the rubber feet to the underside of the FortiGate unit.
•
Insert an Ethernet cable into the one of the 10 ports on the FortiGate unit. Insert the
other end to the router connected to the Internet, or to the modem.
•
Connect the RJ-45 to DB-9 serial cable to the RJ-45 serial connection port. Insert the
other end to a computer or switch.
•
Connect both AC Power Cords to a surge protected power bar or power supply.
•
If you are adding a second FSM module, remove the screws and faceplate and plug
the module into the HDD2 slot.
RJ-45 to DB-9 serial cable
connects to management
computer
Ethernet cables connect to
computers on the internal network
and to the Internet (public switch
or router)
NP2 Powered
311B
1
HDD1
STATUS
ALARM
POWER
HA
1/2
3/4
5/6
7/8
9/10
USB
ASM
CONSOLE
HDD2
Note: The FSM modules are not hot swappable.
PWR 1
PWR 2
Dual power
cables connect
to power supply
Caution: Risk of explosion if battery is replaced by incorrect type. Dispose of used
batteries according to the instructions.
Power Requirements: AC 90-240V, 50-60Hz
Configuration Tools
Web-based manager
Command Line Interface (CLI)
The FortiGate web-based manager is an easy to use management tool.
Use it to configure the administrator password, the interface and default gateway addresses,
and the DNS server addresses.
The CLI is a full-featured management tool. Use it to configure the administrator password,
the interface addresses, the default gateway address, and the DNS server addresses. To
configure advanced settings, see the Tools and Documentation CD included with the
FortiGate unit.
Requirements:
• An Ethernet connection between the FortiGate unit and management computer.
• A web browser such as FireFox or Internet Explorer on the management computer.
Requirements:
• The RJ-45 to DB9 serial connection between the FortiGate unit and management computer.
• A terminal emulation application (HyperTerminal for Windows) on the management
computer.
Collecting Information
NAT/Route Mode
Port
Port
Port
Port
Port
General settings
IP:
____.____.____.____
Administrator password:
Netmask:
____.____.____.____
Network Settings:
Default Gateway:
____.____.____.____
IP:
____.____.____.____
Primary DNS Server:
____.____.____.____
Netmask:
____.____.____.____
Secondary DNS Server:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
The internal interface IP address and netmask must be valid for the internal network.
Transparent mode
Management IP:
IP:
____.____.____.____
Netmask:
____.____.____.____
The management IP address and netmask must be valid for the network from which you will
manage the FortiGate unit.
A default gateway is required for the FortiGate unit to route connections to the Internet.
Factory default settings
NAT/Route mode
Transparent mode
Port 1 interface
192.168.1.99
Management IP
0.0.0.0
Port 2 interface
192.168.100.99
Port 3 interface
0.0.0.0
Administrative account settings
Port 4 interface
10.10.10.1
User name
admin
DHCP server on Internal
interface
192.168.1.110
– 192.168.1.210
Password
(none)
To reset the FortiGate unit to the factory defaults, in the CLI type the command
execute factory reset
Configuring
NAT/Route mode
Transparent mode
You would typically use NAT/Route mode when the FortiGate unit is deployed as a gateway
between private and public networks. In its default NAT/Route mode configuration, the unit
functions as a firewall. Firewall policies control communications through the FortiGate unit.
You would typically use the FortiGate unit in Transparent mode on a private network behind
an existing firewall or behind a router. In its default Transparent mode configuration, the unit
functions as a firewall.
Web-based Manager
Command Line Interface
1. Connect the FortiGate internal interface to a management computer Ethernet interface.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
2. Configure the management computer to be on the same subnet as the internal interface
of the FortiGate unit. To do this, change the IP address of the management computer to
192.168.1.2 and the netmask to 255.255.255.0.
3. To access the FortiGate web-based manager, start Internet Explorer and browse to
https://192.168.1.99 (remember to include the “s” in https://).
4. Type admin in the Name field and select Login.
1. Use the RJ-45 to DB9 serial cable to connect the FortiGate Console port to the management computer serial port.
2. Start a terminal emulation program (HyperTerminal) on the management computer. Use
these settings:
3. Baud Rate (bps) 9600, Data bits 8, Parity None, Stop bits 1, and Flow Control None.
4. At the Login: prompt, type admin and press Enter twice (no password required).
NAT/Route mode
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To configure interfaces
1. Go to System > Network > Interface.
2. Select the edit icon for each interface to configure.
3. Set the addressing mode for the interface. (See the online help for information.)
• For manual addressing, enter the IP address and netmask for the interface.
• For DHCP addressing, select DHCP and any required settings.
• For PPPoE addressing, select PPPoE, and enter the username and password and
any other required settings.
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
To configure a Default Gateway
1. Go to Router > Static and select Edit icon for the static route.
2. Set Gateway to the Default Gateway IP address you recorded above and select OK.
Transparent mode
To switch from NAT/route mode to transparent mode
1. Go to System > Config > Operation Mode and select Transparent.
2. Set the Management IP/Netmask to 192.168.1.99/24.
3. Set a default Gateway and select Apply.
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To change the management interface
1. Go to System > Config > Operation Mode.
2. Enter the Management IP address and netmask that you recorded above and select
Apply.
NAT/Route mode
1. Configure the FortiGate internal interface.
config system interface
edit internal
set ip <intf_ip>/<netmask_ip>
end
2. Repeat to configure each interface, for example, to configure the WAN1 interface.
config system interface
edit wan1
...
3. Configure the primary and secondary DNS server IP addresses.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
4. Configure the default gateway.
config router static
edit 1
set gateway <gateway_ip>
end
Transparent Mode
1. Change from NAT/Route mode to Transparent mode and configure the Management IP
address.
config system settings
set opmode transparent
set manageip <mng_ip>/<netmask>
set gateway <gateway_ip>
end
2. Configure the DNS server IP address.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
Refer to the Tools and Documentation CD for information on how to control traffic, and how to configure HA, antivirus protection, FortiGuard, Web content filtering, Spam filtering, intrusion
prevention (IPS), and virtual private networking (VPN).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising