2008 Frame Pool Setup Instruction.indd
FRAME POOL SETUP INSTRUCTION SHEET
SITE PREPARATION
WARNING - VERY IMPORTANT!
•
•
•
Site must be level. FAILURE TO DO SO MAY CAUSE POOL COLLAPSE.
The pool must be assembled on a smooth and level site of firm soil that is free of stones, gravel, sticks, blacktop or other oil base compounds. Do not install pool on a wooden deck or any type of wooden surface.
FAILURE TO FOLLOW THE INSTRUCTIONS BELOW WILL CAUSE POOL TO COLLAPSE AND
WILL VOID THE WARRANTY!
1. Select a level area, and completely remove all debris, twigs, stones, etc. DO NOT select an area under overhead
electrical lines, trees or within 15 feet of a house, building, etc. The area should also be at least 10 feet away,
and no more than 21 feet away, from a 110 volt AC outlet, protected by a Ground Fault Circuit Interrupter.
2. Contact your local utilities, checking that no underground cables, telephone lines, gas lines, etc. run beneath the
area you have selected.
POOL INSTALLATION
TIP: It will be much easier to install your pool if you unfold it and let it lay in direct sunlight for about 2
hours prior to installation. This will help to insure a wrinkle-free fit because the pool material will be more
pliable allowing it to form into shape during installation.
1. Carefully unfold the Frame Pool and inspect the seams prior to setup. Lay the
pool out flat on the ground, positioning the power filter mounting area of the pool
wall so that it is 10 to 21 feet from the electrical outlet you plan to use for the
pool pump. You should have at least three people to assist with the assembly of
this pool.
92
FIG. 1
2. Locate the metal pipe and Tee Fittings for the frame section of the pool. The
shorter pipe sections with the larger diameter and the pair of holes at both ends are the Horizontal Beams (91).
The longer pipe sections with the smaller diameter and the Spring Pin (96) at one end are the Vertical Legs
(94). Take the Horizontal Beams (91) and insert them into the pockets
91
stitched along the top edge of the pool wall. Rotate it in the pocket so
92
91
that the holes are on the top and bottom of the pipe protruding from
each end of the pockets. Take one end of the pipe and insert it into a Tee
Fitting aligning the holes with the holes in the Horizontal Beam. Do
FIG. 2
NOT install any of the Pins (93) at this time. Continue around the pool
in either direction installing all of the Tee Fittings onto the Horizontal Beams. See Fig 1.
3. When you get to the last connection, install the last Tee Fitting on the end of one of
the beams. Lift up on both of the last two Beams in order to get them to insert into the
Tee Fitting. Angle them towards each other and guide the Beam into the Fitting as you
lower them both down together. See Fig. 2. This step may require two people. Now,
begin inserting the Pins (93) down through the top of the Tee Fittings until the Pin snaps
into place on the lower side of the Fitting as shown in Fig. 3.
93
Should you encounter any problems, contact the Parts Department
at (800) 813-0206 between 8:00 a.m. and 5:00 p.m. Mon. thru Fri. Eastern Standard time.
FIG. 3
4. Once the top frame is assembled, locate the Vertical Legs (94). The Vertical Leg sections will have a Spring Pin
(95) pre-installed at the top end. First, insert the leg down through the belt that runs around the middle of the
pool, see Fig. 4. Now, to connect them into the top frame, push the buttons in as you insert the Leg up into the
Tee Fitting. Look through the hole in the Fitting as you insert and rotate the pipe until the buttons align with the
holes and pop out, locking the leg in place. Finally, take one of the Leg Caps (96) and insert the bottom of the
Vertical Leg into it until it stops.
5. Go around and check all of the Fittings, Legs, and Beams for proper fit, making sure that all the Pins have been
securely fastened in all of the holes. Grab the Vertical Legs at the bottom and gently pull them out making sure
that they remain vertical and perpendicular to the top ring.
6. Make sure the drain fitting is plugged securely and the cap is in place. Start filling the pool with water. After
about 1-inch of water is on the bottom, stop filling and smooth wrinkles out of the bottom of the pool.
7. NOTE: IF MORE THAN 1-2 INCHES OF WATER COLLECTS ON ANY ONE SIDE BEFORE THE POOL
STARTS FILLING IN THE CENTER, THE POOL IS NOT LEVEL ENOUGH, AND MUST BE CORRECTED, SEE “SITE PREPARATION”, PAGE 1. NOTE: THE WEIGHT OF THE WATER WILL PREVENT ANY
ADJUSTMENT AFTER THIS POINT.
8. Continue to check the Vertical Legs and pull them out at the bottom if necessary, making sure they remain vertical and perpendicular to the top ring.
9. Following the instructions under “Power Filter Installation” in the “Swimming Pool Filter System” owner’s
manual, begin installing your power filter unit according to it’s manual.
10. Make sure the drain fitting is plugged securely and the cap is in place.
93
92
95
94
94
96
FIG. 4
96
Should you encounter any problems, contact the Parts Department
at (800) 813-0206 between 8:00 a.m. and 5:00 p.m. Mon. thru Fri. Eastern Standard time.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising