YASKAWA AC Drive-J1000 Option RS

YASKAWA AC Drive-J1000 Option RS
YASKAWA AC Drive-J1000 Option
RS-232C Interface
Technical Manual
Type SI-232/J, SI-232/JC
To properly use the product, read this manual thoroughly and retain
for easy reference, inspection, and maintenance. Ensure the end user
receives this manual.
J1000オプションユニット
RS-232Cインタフェース
オプションユニット
取扱説明書
形式 SI-232/J, SI-232/JC
製品を安全にお使い頂くために,この取扱説明書を必ずお読みください。
また,本書をお手元に保管していただくとともに,最終的に本製品をご使用になる
ユーザー様のお手元に確実に届けられるよう,お取り計らい願います。
J1000
MANUAL NO. TOBP C730600 32A
Contents
1 PREFACE AND SAFETY . . . . . . .5
2 RECEIVING . . . . . . . . . . . . . . . . . .9
3 PRODUCT OVERVIEW . . . . . . . .11
4 OPTION COMPONENTS. . . . . . .12
5 INSTALLATION PROCEDURE . .14
6 RELATED DRIVE PARAMETERS . . .20
7 TROUBLESHOOTING . . . . . . . . .21
8 SPECIFICATIONS . . . . . . . . . . . .22
9 YASKAWA LOCATIONS. . . . . . .23
10 REVISION HISTORY . . . . . . . . .24
TOBPC73060032A RS-232C Interface Technical Manual
3
Copyright © 2007 YASKAWA ELECTRIC CORPORATION
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any
means, mechanical, electronic, photocopying, recording, or
otherwise, without the prior written permission of Yaskawa. No
patent liability is assumed with respect to the use of the
information contained herein. Moreover, because Yaskawa is
constantly striving to improve its high-quality products, the
information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this
manual. Yaskawa assumes no responsibility for errors or
omissions. Neither is any liability assumed for damages resulting
from the use of the information contained in this publication.
4
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
1 Preface and Safety
1 Preface and Safety
◆ Applicable Documentation
The following manuals are available for the RS-232C Interface
Option:
Option Unit
Yaskawa AC Drive -RS-232C Interface
Option Technical Manual
J1000
Read this manual first.
The Technical Manual is packaged with the
RS-232C Interface Option and contains a
basic overview of wiring, settings, functions,
and fault diagnoses.
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
5
1 Preface and Safety
Yaskawa Drive
To obtain instruction
manuals for Yaskawa
products access these
sites:
U.S.: http://
www.yaskawa.com
Europe: http://
www.yaskawa.eu.com
Japan: http://www.emechatronics.com
Other areas: contact a
Yaskawa AC Drive- Yaskawa representative.
J1000
For questions, contact the
Technical Manual
local Yaskawa sales
office or the nearest
Yaskawa representative.
U.S.: Yaskawa AC
Drive-J1000 Quick
Start Manual
Other areas:
Yaskawa AC DriveJ1000 Quick Start
Manual
◆ Terms
Note: Indicates a supplement or precaution that
does not cause drive damage.
Drive:
Option:
6
Yaskawa AC Drive -J1000 Series
Yaskawa AC Drive -J1000 RS-232C Interface
Option
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
1 Preface and Safety
◆ Registered Trademarks
• Other company names and product names listed in this manual
are registered trademarks of those companies.
◆ Supplemental Safety Information
Read and understand this manual before installing, operating, or
servicing this option unit. The option unit must be installed
according to this manual and local codes.
The following conventions are used to indicate safety messages in
this manual. Failure to heed these messages could result in serious
or possibly even fatal injury or damage to the products or to related
equipment and systems.
DANGER
Indicates a hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a hazardous situation, which, if not avoided, could
result in death or serious injury.
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
7
1 Preface and Safety
CAUTION
Indicates a hazardous situation, which, if not avoided, could
result in minor or moderate injury.
NOTICE
Indicates an equipment damage message.
8
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
2 Receiving
2 Receiving
◆ Receiving
Confirm the packaging after receiving the RS-232C Interface
Option. If the wrong model is received or the RS-232C Interface
Option does not function properly, contact your supplier.
Components packaged with the option:
• The RS-232C Interface for copy unit/PC communication (SI232/J or SI-232/JC)
• Technical manual
◆ Additional Parts (Sold Separately)
Option
Drive Wizard
Plus
Part
Number
Comments
-
Available for download from
e-mechatronics.
www.e-mechatronics.com
for
or at www.yaskawa.com in the
U.S.
PC Interface
Cable
WV103
D-sub 9 pin - RJ-45
USB Copy Unit
JVOP-181
Provided with an RJ-45 cable
and a USB cable
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
9
2 Receiving
Part
Number
Comments
LED Operator
JVOP-182
Available soon
(Contact Yaskawa for detail)
LED Operator
Cable
1 meter:
WV001
3 meter:
WV003
CAT5e UTP straight-through
cable with RJ-45 8 pin
connector
Option
◆ Tool Requirements
Use a flat-blade screwdriver with the dimensions below for
installation or removal of the option cover and RS-232C option.
Blade width
Blade thickness
3.0 mm max.
0.6 mm max.
10 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
3 Product Overview
3 Product Overview
◆ About this Product
The RS-232C Interface Option allows the drive to be connected to
a network or external device.
Possible connected devices include:
• LED Operator
• Personal computer using DriveWizard Plus
• USB Copy Unit
These devices can be used to edit, view, and copy parameter
settings in the drive.
SI-232/JC can be more easily connected and disconnected than SI232/J. This is useful when copying parameter settings between
multiple drives.
◆ Applicable Models
The RS-232C Option can be used with Yaskawa drive models in
the table below.
Drive
Drive Software Version <1>
CIMR-J……A…………BA…
≥1010
<1> See “PRG” on the drive nameplate for software version
number.
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 11
4 Option Components
4 Option Components
Figure 1
A
C
D
J1000
B
A – RJ-45 Port
B – Option
Model
Number
C – Option
Connector to
Drive
D – Connection
Tabs <1>
<1> Connection tabs are found only on the RS-232C interface (SI232/J).
12 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
4 Option Components
◆ Dimensions
The installed Option interface adds 17.8 mm (0.70 in) to the total
depth of the drive.
2.8(0.11)
15(0.60)
mm(in)
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 13
5 Installation Procedure
5 Installation Procedure
◆ Section Safety
DANGER
Electrical Shock Hazard
Disconnect all power to the drive, before servicing.
Failure to comply will result in death or serious injury.
Wait at least one minutes after all indicators are off. The drive
has internal capacitors that remain charged even after the 24 V
Power Supply option is disconnected. The drive charge LED
will extinguish when the DC bus voltage is below 50Vdc.
Measure drive DC bus voltage to confirm safe level.
14 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
5 Installation Procedure
NOTICE
Damage to Equipment
Use only Yaskawa connection cables or recommended
cables.
Failure to comply may cause the drive or option to function
incorrectly.
Properly connect the connectors.
Failure to comply may prevent proper operation and possibly
damage equipment.
Do not exceed communication cable bend radius
specifications.
Failure to comply may result in broken wires or loose
connections.
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 15
5 Installation Procedure
◆ Attaching the Option Interface
1. Insert a flat-blade screwdriver into the
2.
opening as shown in the diagram below to
remove the option cover from the drive.
Insert the connector on the back of the
interface into the CN5 port on the drive so
that it clicks into place.
Note: The RS-232C Interface (SI-232/J) has three
additional connection tabs that must also
click into place to properly mount the
option.
flat-blade
screwdriver
CN5 port
Tab
Tab
ab
16 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
5 Installation Procedure
◆ Removing the option interface
1. Use a flat-blade screwdriver as shown in
the diagram to press gently against the
small openings and disconnect the option
unit.
J10
00
underside of
interface unit
flat-blade
screwdriver
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 17
5 Installation Procedure
◆ Connecting Peripheral Devices to the
RS-232C Interface Option
NOTICE: Only use specific cables recommended by
Yaskawa. Yaskawa cannot guarantee proper operation if
non-specified cables are used.
AC drive J1000
SI-232/JC
J1000
SI-232/J
or
<4>
<2>
USB Copy Unit
USB Copy Unit
ERR
<1>
CN5
LED Operator
(Available soon)
Re
ad
Ve
rify
Co
py
COM
connect
J1000
LOCK
JVOP-181
YASKAWA
<3>
DriveWizardPlus
18 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
5 Installation Procedure
<1>
<2>
<3>
<4>
Use the LED operator cable, WV001 or WV003.
Only use the RJ-45 cable supplied with the USB Copy Unit.
Only use the USB cable supplied with the USB Copy Unit.
Only use the cable, PN: WV103, when connecting the drive
to a PC.
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 19
6 Related Drive Parameters
6 Related Drive Parameters
No.
Name
o2-06
Operation
Selection
when Digital
Operator is
Disconnected
Description
Default
Determines if the drive will
stop when the digital operator
is removed in Local mode or
with b1-02 set to zero.
0: Disabled - The drive will
not stop when the digital
0
operator is removed.
1: Enabled - The drive will
fault (OPR) and coast to
stop when the digital
operator is removed.
20 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
7 Troubleshooting
7 Troubleshooting
Problems with the option interface may trigger an operator error.
Refer to the J1000 Technical Manual for all other errors.
◆ Fault
LED Operator
Display
oPr
Cause
Fault Name
Digital operator connection fault
Possible solution
• Check the connection between the LED
LED operator is
operator and the drive
not properly
• Replace the cable if damaged
connected to the
• Turn off the drive input power and
drive or cables are disconnect the LED operator
damaged
• Next reconnect the operator and turn the
drive input power back on
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 21
8 Specifications
8 Specifications
◆ Drive Specification
Item
Specification
Model
Number
SI-232/J: RS-232C Interface for use with remote
digital operator
SI-232/JC: RS-232C Interface for use with copy
unit and PC communication
Storage/
Installation
Area
Indoors (an area free from oil mist and dust)
Ambient
Temperature
-10 to +50°C
Humidity
95% RH or less with no condensation
Storage
Temperature
-20 to +60°C allowed for short-term transport of
the product
Altitude
1000 m or less
22 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
9 Yaskawa Locations
9 Yaskawa Locations
IRUMA BUSINESS CENTER (SOLUTION CENTER)
480, Kamifujisawa, Iruma, Saitama 358-8555, Japan
Phone 81-4-2962-5696 Fax 81-4-2962-6138
YASKAWA ELECTRIC AMERICA, INC.
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone 1-847-887-7000 Fax 1-847-887-7370
YASKAWA ELETRICO DO BRASIL LTDA.
Avenida Fagundes Filho, 620 Sao Paulo-SP CEP 04304-000, Brazil
Phone 55-11-3585-1100 Fax 55-11-5581-8795
YASKAWA ELECTRIC EUROPE GmbH
Am Kronberger Hang 2, 65824 Schwalbach, Germany
Phone 49-6196-569-300 Fax 49-6196-569-312
YASKAWA ELECTRIC UK LTD.
1 Hunt Hill Orchardton Woods Cumbernauld, G68 9LF, United Kingdom
Phone 44-1236-735000 Fax 44-1236-458182
YASKAWA ELECTRIC KOREA CORPORATION
7F, Doore Bldg. 24, Yeoido-dong, Youngdungpo-Ku, Seoul 150-877, Korea
Phone 82-2-784-7844 Fax 82-2-784-8495
YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.
151 Lorong Chuan, #04-01, New Tech Park 556741, Singapore
Phone 65-6282-3003 Fax 65-6289-3003
YASKAWA ELECTRIC (SHANGHAI) CO., LTD.
No.18 Xizang Zhong Road. Room 1702-1707, Harbour Ring Plaza Shanghai 200001, China
Phone 86-21-5385-2200 Fax 86-21-5385-3299
YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE
Room 1011A, Tower W3 Oriental Plaza, No.1 East Chang An Ave.,
Dong Cheng District, Beijing 100738, China
Phone 86-10-8518-4086 Fax 86-10-8518-4082
YASKAWA ELECTRIC TAIWAN CORPORATION
9F, 16, Nanking E. Rd., Sec. 3, Taipei, Taiwan
Phone 886-2-2502-5003 Fax 886-2-2505-1280
(Address revision No.: 07-8-13)
YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual 23
10 Revision History
10 Revision History
The revision dates and numbers of the revised manuals are given
on the bottom of the back cover.
MANUAL NO. TOBP C730600 32A
Published in Japan
December 2007 07-12
Date of
publication
Date of original
publication
Date of
Published
Rev.
No.
Section
Revised Content
December 2007
–
–
First edition
24 YASKAWA ELECTRIC TOBPC73060032A RS-232C Interface Technical Manual
YASKAWA AC Drive-J1000 Option
RS-232C Interface
Technical Manual
Any inquiries related to the product can be directed to the address listed at chapter 9.
YASKAWA ELECTRIC CORPORATION
YASKAWA
In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture
thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure
to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply.
Specifications are subject to change without notice for ongoing product modifications and improvements.
© 2007 YASKAWA ELECTRIC CORPORATION. All rights reserved.
MANUAL NO. TOBP C730600 32A
Published in Japan December 2007 07-12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising