AR-721E

AR-721E
SOYAL
®
AR-721E
V100630
ACCESS CONTROL SYSTEM
Contents
2 User Guide
1 Product
3 Specification
Separate controller connected to 2 WG readers, can enhance the security of the system.
Can connect to Door Open Button, Door Sensor, and Tamper Switch.
When Door open to Long or Force open, it's can be detected.
4 Control Mode, allowing users the flexibility of use with.
Can automatically determine to use stand-alone or networking.
Specification
CPU
8 bit CPU
Temperature
-20℃ ~ +60℃
Event log
1456
RAM
512 k Bits
Digital Input
2 Door Open Button/ 2 Door Sensor/ 2 Housing open detection/ Prepared for 2 DI
Aux. WG Port
WG 26 / WG 34
Power Supply
10 ~ 24
Relpy Output
2 Door Relay/ 1 Alarm Relay/ Prepared for 1 Relay output
Anti-pass-back
YES
Power Consumption
< 3W
Transistor Output Prepared for 2 DO
Lift Control
NO
Interface
RS-485
Door Relay Time
Time Zone
63 (stand-alone /networking)
Baud Rate
9600 bps﹐N﹐8﹐1
Alarm Relay Time Toggle, 0.1~600Ses
Real Time Clock
YES
External WG Readers
2 WG (Controller power supply)
User Capacity
DIP_SW
4 (Node ID: 1~16)
Toggle, 0.1~600Ses
3,000
Connector Table
P5
8
7
P4
6 5
4
2
3
2 1
OUT 1
12 11 10 9
8
7
P1
Connector: P1
2 1
Code
LA+
LBGND
DC 12V
N.O.
ALM
N.O.
3
3
DO 1
N.O.
4
Dip-switch
4
4
2 1
OUT 2
ON
1
3
Connector: P2
Code
COM
OUT1
BZ
LG
LR
TAM
SEN
PB
WD1
WD0
GND
12V
N.O.
6 5
4
3
2 1
P2
3
2 1
P3
Node ID is setting by DIP_Switch
ON
Node ID: 01~16
1
2
3
4
1
2
3
4
ON
off
off
off
Node ID 02
off
ON
off
off
Node ID 03
ON
ON
off
off
Node ID 15
ON
ON
ON
ON
Node ID 16
off
off
off
off
DIP SW
Node ID 01
Connector: P3
~
Code
COM
DI2
DI1
Wiring Diagram
P1
AR-321H
Connect to PC
Converter
Pin
1
2
3
4
Description
RS-485(A+)
RS-485(B-)
DC Power 0V
DC Power 12V
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Description
COM
N.C./N.O.
Beeper Output
LED Green Output
LED Red Output
Tamper Switch Input
Door Sensor Input
Exit Switch Input
Wiegand DAT:1 Input
Wiegand DAT:0 Input
DC Power 0V Output
DC Power 12V Output
Pin
1
2
3
Description
COM
DI 2
Fire-alarm Input
Connector: P4
Code
COM
DO1
COM
ALM
Connector: P5
Code
COM
OUT2
BZ
LG
LR
TAM
SEN
PB
WD1
WD0
GND
12V
Connector: P6
Code
DO3
DO2
Pin
1
2
3
4
Description
COM
N.C./N.O.
COM
N.C./N.O.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Description
COM
N.C./N.O.
Beeper Output
LED Green Output
LED Red Output
N.C.
N.C.
N.O.
Wiegand DAT:1 Input
Wiegand DAT:0 Input
DC Power 0V Output
DC Power 12V Output
Pin Description
1 DO 3
2 DO 2
P4 Connect to Alarm or Other Equipment
12V
GND
BA+
POWER
12VDC
Equipment
12V
GND
AR-721E P1
12V
B- A+
4 3 2 1
Alarm
4 3 2 1
COM
12 11 10 9
COM
P6
2 1
AR-721E P4
POWER
12VDC
2 Door WG Controller
P5 Connect to Magnet Lock or Electric Bolt
P2
AR-321H
Connect to Electric Strike
POWER
12VDC
Electric Strike
POWER
12VDC
or
Magnet Lock
N.C.
Electric Bolt
N.C.
N.C.
COM
N.C.
COM
BZ
GLED
RLED
WG 1
WG 0
GND
12V
Door Sensor
Tamper Switch
N.O.
Reader A
BZ
GLED
RLED
WG 1
WG 0
GND
12V
Door Sensor
N.O.
Reader B
EXIT
EXIT
12 11 10 9 8 7 6 5 4 3 2 1
AR-721E P2
Reader
N.O.
N.C.
N.C.
GND
12V
N.O.
N.O.
N.C.
N.C.
12 11 10 9 8 7 6 5 4 3 2 1
Push Button
N.C.
Tamper Switch
Push Button
AR-721E P5
※ Notice
If the Power line more than 100 m between the Controller and Reader, it is recommended NOT to use the "Wiegand Power".
12 11
See connection mode within the dashed box , Controller and Reader must to do "common-COM-point".
P3
AR-321H
About Digital Input
P6 About Transistor Output
N.C.
N.O.
COM
CTL
12V
N.O.
N.O.
Relay Outpot Module
Equipment
Equipment
N.C.
N.O.
COM
CTL
12V
DI 1
DI 2
COM
3 2 1
Relay Outpot Module
AR-721E P3
POWER
12VDC
12V
GND
P6
AR-721E
4 3 2 1
2 1
DO 3
AR-721E
DO 2
POWER
V100630
P1
Adding and Deleting Tag
Add Single Tag or Random tags
Input
123456
(or Master Code) → 19 UUUUU 00001
[e.g.] 2 readom cards with user addresses No. 100 and No. 101:
Access programming mode → 19
00100
00001
→ Present the tag(s) with reader (single tag or random numbered cards one by one) → Done
→ Present the tags one by one → Done
Add the Sequential tags
Input
123456
(or Master Code) → 19
UUUUU
QQQQQ
→ Present the tags (Present the tag with the lowest number first.) → OK
[e.g.] User Address NO.101 to NO.120 have 20 pcs of sequential tags:(62312~62332):
Access programming mode → 19
00101
00120
→ Close Tag into RF Area(only use the tag NO.62312) → OK
Delete a Single Tag
Delete All Tags
Input
123456
(or Master Code) → 10
[e.g.] Delete User Address: 00058
Access programming mode → 10
SSSSS 9 EEEEE
Input
123456
(or Master Code) → 29
29
Tag Information
00058 9 00058
Delete a batch of Tags
Input
123456
(or Master Code) → 10
[e.g.] Delete User Address: 00101~00245
Access programming mode → 10
SSSSS 9 EEEEE
CARD CODE
SITE CODE
00101 9 00245
Operation process
A. Enter/ Exit Program Mode
Enter the program mode
Input
123456
or
PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input
876112
→ program mode accessed
Exit the program mode
Input
Master Code modification
Access programming mode → 09 PPPPPPRRRRRR
[e.g.] Set the Master code to be 876112, input
123456
[Input the 6-digit new master code twice.]
→ 09 876112876112
CARD CODE
SITE CODE
SOYAL
®
AR-721E
V100630
ACCESS CONTROL SYSTEM
B. Chang the Node ID of Reader
Access programming mode → 00
NNN
[Node ID: 001~255]
C.Set up M4/M8
Access programming mode → 04
N
[N=4/8]
D. Set up the password
Card or PIN: Access programming mode → 12
Card and PIN: Access programming mode → 13
UUUUU
PPPP
UUUUU
[e.g. User address: 00001 and pass code: 1234, input 12
PPPP
[e.g. User address: 00001 and pass code: 1234, input 13
00001
00001
1234
1234
E. Anti-pass-back(Reader A and Reader B must to be setting)
Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or to situations need
access and exit monitor.
Controller enable
Access programming mode → 20 DDD
[128= Anti-pass-back(0=Disable; 1=Enable)/ 064=Access/Exit(0=Exit; 1=Access).]
[e.g.] Enable Anti-pass-back, and set to Exit door= (128 x 1) + (064 x 0) = 128
Access programming mode → 20 128
(Please refer to function default value for details.)
Card enable
Access programming mode → 26
SSSSS
EEEEE
N
[SSSSS= User address start; EEEEE= User address end; N=0(control)/ 1(Not control)/ 2(reset)]
[e.g.] User address from 00152 to 00684 enable the anti-pass-back function: 26 00152 00684
0
[e.g.] No. 154 enable the anti-pass-back, and induction into the door has not been induced to leave. When he re-induction into the door will become
invalid , then he needs to set the reset. Access programming mode → 26
00154
00154
2
→ Reset
F. Auto Open Time Zone
Door will keep open after the first flashing card.There are 2 time zones supported.
Enable/Disable auto open zone
Access programming mode → 20
004
[004= enable Auto-Open Time Zone; 000= disable Auto-Open Time Zone]
Enable/Disable auto open door without presenting card
Access programming mode → 24
001
[001= enable Auto-Open Time Zone; 000= disable Auto-Open Time Zone]
Set up open time
Access programming mode → 08 N HHMMhhmm 6543217H
N: 2 sets of auto-open zone (N=0=1st set; N=1=2nd set)
HHMMhhmm=Staring time to ending time (e.g. 08301200=08:30 to 12:00)
6543217H= 7 days of week (Sat/Fri/Thu/Wed/Tue/Mon/Sun) + Holiday (F= 0: disable; 1: enable); Holidays establish by the software.
[e.g.] To set the second time zone as 9:30 AM to 4:20 PM, Monday, Wednesday and Friday: 08 1 09301612 01010100
→ Done
G. Setting Up the Arming
Alarm conditions:
1. Arming is enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: When power is off and then on, reader on arming bffore power off.
Enable/Disable Arming status (Factory default armingcode is: 1234) :
Standby Mode
Door is not open
After door open
The normal procedure to open door → Input 4 digit arming code →
→ Input 4 digit arming code → Present valid card
Enter Program Mode
Enable: Access programming mode →
Disable: Access programming mode →
※ [The normal procedure to open door] can refer to [Access Mode].
Function Default Value
20
DDD
Selection
1: No
※0: Yes
Auto Re-lock
※0: Disable
1: Enable
1
002
Networking/Stand-Alone
Auto Open
※0: Disable
1: Enable
2
004
Networking/Stand-Alone
0: Disable
※1: Enable
4
016
Networking/Stand-Alone
Door open button input
Bit
0
Value
001
※Default Value
Application
Networking
Function
Attendance
Master Reader of Network
※0: Slave
1: Mater
5
032
Networking
Access/Exit
※0: Exit
1: Access
6
064
Networking
Anti-pass-back
※0: Disable
1: Enable
7
128
Networking
Bit
0
Value
001
6
064
24
DDD
Function
Auto-open door without cards at auto open zone
Selection
1: Enable
※0: Disable
Stop Alarm by door close or by push button
※0: None
1: Yes
※Default Value
Application
Networking/Stand-Alone
Networking/Stand-Alone
]
]
2 Door WG Controller
28
DDD
V100630
※Default Value
Application
Networking/Stand-Alone
Bit
5
Value
032
1: Enable
6
064
Networking/Stand-Alone
1: Enable
7
128
Networking/Stand-Alone
Function
Can be password-free in the Card or PIN mode
Selection
1: Enable
※0: Disable
Reset the Anti-pass-back by the software
※0: Disable
Arming for force open
※0: Disable
Selection= 0(none value)/ 1(1 x each value)
[e.g.] DDD value of Enable “Auto Open” + ”Exit by Push Button +”Anti-pass-back” =004+016+128=148;
As a result of that, the command will be 20 148 .
Mode4/ Mode8
Mode 4: 1.Card only; 2.Card and PIN (4-digit PIN) +
; 3.Card or User address (5-digit) + Individual PIN (4-digit individual PIN) +
Mode 8: 1.Card only; 2.Card and PIN (4-digit individual PIN) +
; 3.Card or PIN (4-digit individual PIN)
Command List
※ General instructions
Function
Command
Description
PPPPPP
Entering programming mode
Notes
PPPPPP=Master Code, default value=123456
Exiting programming mode
Control mode setting
04
N
Master card setting
07
SSSSS
Auto-open time zone setting
08
N
N=Mode 4=Mode4;8=Mode8
EEEEE
SSSSS-EEEEE=00000-02999;
SSSSS=Starting user address; EEEEE=Ending user address
HHMMhhmm
6543217H
N= 0(1st time zone) / 1(2nd time zone)
HHMM= Starting time; hhmm= ending time
(i.e.: 08301200=08:30 to 12:00)
6543217H= 7 days of week (Sat/Fri/Thu/Wed/Tue/Mon/Sun) + Holiday
(F= 0: disable; 1: enable); Holidays establish by the software.
Master code setting
09
PPPPPPRRRRRR
Suspend / Delete tag
10
SSSSS
10
SSSSS=Starting user address, EEEEE=Ending user address
PPPPPP=New master code
RRRRRR=Repeat the new master code
EEEEE
=Suspend
9
=Delete;
Active the suspended cards
11
SSSSS 9 EEEEE
SSSSS EEEEE
Set the cards as Card mode OR PIN mode
12
UUUUU
PPPP
Access mode: Card or PIN; UUUUU=user address;
13
UUUUU
PPPP
Access mode: Card and PIN; UUUUU=user address;
15
PPPP
SSSSS=Starting card number, EEEEE=Ending card number
by user address
Set the cards as Card AND PIN mode
PPPP=4-digit pass code 0001~9999
by user address
Duress code setting
PPPP=4-digit pass code 0001~9999
PPPP=4-digit pass code (default value=4321)
P.S. Duress code will be unavailable and become a public PIN at access mode “Card or PIN” of M6
Card number modification
16
UUUUU
Arming pass code setting
17
PPPP
SSSSSCCCCC
UUUUU= User address; SSSSS=5-digit site code; CCCCC=5-digit card code
PPPP=4-digit pass code ( default value=1234; disable Arming PWD=0000)
P.S. Arming PWD code will be unavailable and become a public PIN at access mode “Card PIN” and of M6
Door open waiting time
18
TTT
Set the card by induction(M4/M8)
19
UUUUU
TTT=Door open waiting time: 001~600=1~600 sec.; default value: 15 sec.
QQQQQ
UUUUU=User address;
QQQQQ=Card quantity(00001=Continuously inducting)
Controller parameter setting
24
DDD
Please refer to function default value for details.
Controller time clock setting
25
YYMMDDHHmmss
YYMMDDHHmmss: Year/ Month/ Day/ Hour/ Min./ Sec.
Anti-pass-back (Enable user)
26
SSSSS
EEEEE
N
SSSSS=Starting user address; EEEEE=Ending user address;
N=0/Enable; N=1/Disable; N=2/Initial
Controller control setting
28
DDD
Delete all tags
29
29
※ Individual instruction set
Function
Command
Keyboard Lock/ Unlock
Please refer to function default value for details.
Description
Notes
Press and hold for 2 seconds to lock the keyboard, again to unlock.
Exiting programming mode and enabling arming status
Node ID setting (for Reader)
00
NNN
NNN=Node ID, range: 001~254
Door relay time setting
02
TTT
TTT=Door relay time 000= Output constantly
001~600=1~600 sec.
601~609=0.1~0.9 sec.
Alarm relay time setting
03
TTT
TTT=Alarm relay time 001~600=1~600 sec.
Controller additional setting
20
DDD
Please refer to function default value for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising