ADSL2+ Wireless N150 Modem Router
Right click on Local Area Connection and select Properties
Double click on Internet Protocol TCP/IP
Ensure “Obtain an IP address automatically” is selected
Ensure “Obtain DNS server address automatically” is
Click on OK
Configuring in Layer2 PPPoE for Windows XP and 2000
Important Message
Your modem has been pre-configured, you do not need to
follow each step of the set-up guide but should retain this
document in case you need to manually configure your
To configure your PC/Laptop with your wireless password
please proceed to step 4d. To change your wireless
password please proceed to step 4.
Physical Connection
Network Configuration
Configuring Internet Connection in Layer 2 PPPoE
Configuring Wireless
Change of Password
1. Physical Connection
Please refer to diagram CASE2 in the Quick Reference Guide.
Please note: Have your router powered on and
connected directly to your PC via Ethernet Cable
before you begin, as these instructions are based
on wired Ethernet connection
2. Network Configuration
PPPoE connection does not require you to have an IP address or
DNS settings manually encoded on your network card. PPPoE
connection uses authentication to establish the Internet connection
and its after doing this that your router is assigned an IP and DNS
settings from TPG.
To begin, your PC needs to receive a private IP address from the
router. Most ADSL routers have DHCP enabled by default that will
take care of this.
To ensure your Network Card is ready for this, please follow the
following steps:
Click on Start -> Settings ->Control Panel -> Network
Page 1 of 4
3. Configure Layer 2 PPPoE
Open your browser and in the address bar type and press enter
Enter admin for both the username and password and click on
OK. If you have changed the login credentials, please enter the
current username and password for your router interface.
You may change the password by entering in a new password.
Click NEXT to continue.
Select the appropriate time zone for your location. Click NEXT
to continue.
In the ISP Connection Type screen, choose PPPoE/PPPoA.
Click NEXT to continue.
Enter the following connection information into relevant field,
Click NEXT to continue.
You should now see the site map screen.
Username: can be found in the ADSL Configuration Details
Password: the password you nominated at the time of
VPI: 8
VCI: 35
Connection Type: PPPoE LLC
You can use Quick Start to setup the router’s ADSL connection
with ease. Click Quick Start to get into the quick setup
Click RUN WIZARD to start up this procedure.
Page 2 of 4
Please click NEXT to confirm your changes.
Go to Interface -> Wireless to setup the wireless parameters.
Ensure that the following is selected:
SSID: Netcomm Wireless (router default)
Note: SSID is the name of your wireless network. You can
change the SSID. Only devices with the same SSID can
Authentication Type: WPA-PSK/WPA2-PSK
Encryption: TKIP/AES
Pre Shared Key: initially configured to be the same as
your TPG password.
Note: Pre Shared Key is the password of your wireless
network. You can enter your own password as an option.
Please click CLOSE to exit the Quick Start Wizard.
4. Configuring Wireless
Things you need to know before you begin:
By default the NB14WN that you purchased from TPG is
configured with the following wireless security settings:
SSID (name for the wireless connection): Netcomm
Wireless (router default)
Authentication Type: WPA-PSK/WPA2-PSK
Encryption: TKIP/AES
Pre Shared Key: initially configured to be the same as
your TPG password. You can enter your own text as an
Click on Save
To connect using wireless, go to Start -> Control Panel
Double click on ‘Network Connections’
Right click on your wireless adapter and go to ‘View Available
Wireless Networks’
To use Wireless be sure that you already have set up your
wireless adapter.
To begin your wireless setup please connect your computer
to your router via Ethernet cable.
If you are still logged into your router, click on “Wireless” in the
top menu. If you are not logged in anymore use your browser
to go to and login with admin as the username and
admin as your password.
Page 3 of 4
Find the SSID (network name) of your router and click on Connect.
By the default, the network name should be Netcomm Wireless.
However if you have changed the network name in step 4c, please
select your personal wireless network name.
You will now be prompted to enter your WAP Key /wireless
password. This is the same as your TPG password if you did not
change it on the router.
Click on Connect.
You should now see your status as ‘Connected’.
Your Netcomm NB14NW modem is pre configured with the TPG
IPTV settings. Should you require further assistance please contact
the TPG helpdesk on 131423 opt 2
6. Change of Password
For security purposes we highly recommend that you change your
password if you are using your default or if you believe your password
security has been compromised.
To change your password, first please visit
Your new password will take approximately 10-15 minutes to take
effect, after which you must reconfigure your new password in your
To update the password in your router, please follow Step 3 of this
guide (Configure Layer 2 PPPoE).
Please Note: ADSL routers will by default be capable
of automatic authentication. This means your
router will use your credentials you have provided
to make the Internet connection. Each time your
router is powered on, it will initialize this automated
authentication process after which your router
will receive a public IP address (fixed or dynamic
depending on your plan) and DNS settings from TPG
Support Information
For any installation, configuration or billing enquiries, please call:
13 14 23
Or you can email your queries to helpdesk@tpg.com.au
Or visit www.tpg.com.au/helpdesk for further information.
The Help Desk service is available:
Monday to Friday
8:00am - Midnight
9:00am - 9:00pm
Public holidays
9:00am - 6:00pm
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF