D1260/D1260B - Bosch Security Systems

D1260/D1260B - Bosch Security Systems
D1260/D1260B
Owner's Manual
EN
Keypad
D1260/D1260B | Owner's Manual
This system includes a telephone line seizure feature. The system may be programmed to
communicate with a central monitoring station to report system events. You will not be
able to use your phone while the system is communicating with the central monitoring
station. In the unlikely event that the central station is not able to receive the report, your
phone may be unavailable for up to 20 minutes while the panel makes additional
communication attempts.
Some commands listed below may not be available. Contact your security company for
more information.
Cleared Events Are Not Lost ............................. 14
Contents
Entry Delay Tone and Display............................ 14
Introduction .................................................. 5
Exit Delay Tone and Display .............................. 14
Your Keypad ......................................................... 5
Keystroke Checking Tones ................................ 14
About This Owner’s Manual ................................. 6
Silencing an Alarm............................................. 14
Part I: Security system basics ........................ 7
To SILENCE an alarm: ....................................... 14
Using the keypad ................................................. 7
How Your System Reports Alarms ..................... 15
Command center keys ......................................... 7
Part II: System Commands ........................... 16
Points ................................................................. 8
Entering a Passcode .......................................... 17
What is a Point? ................................................... 8
Turning On the System (Arming) ...................... 17
Controlled Points ................................................ 8
To Turn Your Security System On (Arm): .......... 17
24-Hour Points ..................................................... 8
Turning Off the System (Disarming) ................. 17
Your Custom Display ........................................... 8
To Turn Your Security System Off (Disarm): ..... 18
View Faulted or Bypassed Points ........................ 9
Turning On the System (Arming) With a Duress
Passcode ........................................................... 18
To automatically scroll faulted or bypassed points
................................................................. 9
Warning Displays and Tones .............................. 10
Keypad Quiets for Keystrokes ........................... 10
Priority of Events ............................................... 10
Fire Alarms ......................................................... 11
Silencing Fire Alarms ......................................... 11
Burglary Alarms.................................................. 12
Silencing Burglary Alarms .................................. 12
Fire Trouble and Fire Supervisory Events .......... 13
Silencing Fire Trouble and Fire Supervisory
conditions .......................................................... 13
Special Fire Trouble and Fire Supervisory Display
13
Viewing Fire Trouble and Fire Supervisory
conditions .......................................................... 13
Turning On the System (Arming) With Doors or
Windows Open .................................................. 18
MASTER ARM ? (COMMAND + 1) ...................... 20
Description ........................................................ 20
Using Master Arm: ............................................. 20
Master Arming all Areas .................................... 20
MASTER ARM INST ? (COMMAND + 1 + 1) ....... 22
PERIMETR INST (COMMAND + 2) ..................... 23
Turn On the Perimeter With No Delays ............. 23
Using Perimeter Inst: ........................................ 23
PERIMETR DELAY ? (COMMAND + 3)................ 24
Turn On the Perimeter With Delays .................. 24
Silence the Trouble Sounder & Clear Trouble
Display (COMMAND + 4) ................................... 24
Description ........................................................ 24
Non-Fire Trouble and Supervisory Events ......... 13
Using COMMAND 4: .......................................... 24
Silencing Non-Fire Trouble and Supervisory
Events ............................................................... 13
VIEW MEMORY ? (COMMAND + 4 + 0) .............. 25
Special System Trouble Display ........................ 14
Using View Memory: .......................................... 25
2
View Event Memory ........................................... 25
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Contents
WALK TEST ? (COMMAND + 4 + 4) .................... 26
Description ........................................................ 51
Walk Test ........................................................... 26
Using Chg SKEDS .............................................. 51
RESET SENSORS ? (COMMAND + 4 + 7) ........... 27
DEL USER ? (COMMAND + 5 + 3) ..................... 54
Reset Sensors .................................................... 27
CHG RELAYS ? (COMMAND + 5 + 4) ................. 55
Using Reset Sensors: ......................................... 28
CHG PASSCODES ? (COMMAND + 5 + 5) ......... 56
WATCH MODE ? (COMMAND + 6) ..................... 29
Description ........................................................ 56
Watch Mode....................................................... 29
Using Chg Passcodes ........................................ 56
Entering Watch Mode: ....................................... 29
ADD/CHANGE USER (COMMAND + 5 + 6) ........ 57
Exiting Watch Mode: .......................................... 29
DEFAULT TEXT ? (COMMAND + 5 + 7) .............. 65
PERIMETR PART ? (COMMAND + 8) .................. 31
FIRE TEST ? (COMMAND + 5 + 8) ..................... 66
Partially Turn On the Perimeter ......................... 31
DISPLAY REV ? (COMMAND + 5 + 9) ................. 68
Using Perimetr Part: .......................................... 31
SERVICE MENU ? (9 + 9 + Enter) ...................... 68
Special Alerts (COMMAND + 7 and COMMAND +
9)
............................................................... 32
Using View Log .................................................. 69
Using COMMAND 7: ........................................... 32
Using Display Rev .............................................. 71
Using COMMAND 9: ........................................... 32
Using Service Walk Test .................................... 71
Part III: Advanced Commands ...................... 34
Using Default Text ............................................. 72
Advanced Commands ........................................ 34
Using Setup ....................................................... 72
Terms Used in This Section ............................... 34
Part IV: Multi-Area Use ................................. 74
BYPASS A POINT? (COMMAND + 0) ................. 36
Description ........................................................ 36
Working with Multiple Areas from a Single
Command Center .............................................. 74
Using Bypass a Point ......................................... 36
View Area Status ............................................... 75
UNBYPASS A POINT? (COMMAND + 0 + 0) ....... 38
View Point Status .............................................. 75
Description ........................................................ 38
MOVE TO AREA ? (COMMAND + 5 + 0) ............. 76
Using Unbypass a Point: .................................... 38
Turning On the System ..................................... 77
SEND REPORT ? (COMMAND + 4+1 or 4+2) ..... 40
Turning on Selected Areas ................................ 77
Description ........................................................ 40
Turning on Multiple Areas with a Passcode ...... 78
Using Send Report ............................................. 40
Faulted Points in Other Areas ........................... 78
REMOTE PROGRAM ? (COMMAND + 4 + 3) ...... 41
Turn On the Entire System Without Delays....... 79
Description ........................................................ 41
Turning on All or Selected Areas ....................... 79
For systems without a phone number ............... 41
Turning Off the System ..................................... 80
For systems with a phone number or network
connection ......................................................... 42
Turning Off Multiple Areas with a Passcode ..... 80
CHANGE TIME/DATE (COMMAND + 4 + 5) ........ 44
Turning Off Selected Areas ............................... 81
DOOR CONTROL (COMMAND + 4 + 6).............. 45
Appendix ..................................................... 83
Description ........................................................ 45
Using Door Control ............................................ 45
Supplementary Information for Adding Passcodes
.............................................................. 83
Access Level ...................................................... 47
User Authority Levels ........................................ 83
CHANGE DISPLAY (COMMAND + 4 + 9) ............ 48
Passcode Worksheet ......................................... 83
Brighten/Dim Display ........................................ 48
User Interface .................................................... 83
Show Continuous Time/Date............................. 48
User Interface .................................................... 85
EXTEND CLOSING (COMMAND + 5 + 1) ............ 49
User (Passcode) Worksheet (User 000 to 038) 86
Using Print Log .................................................. 70
Turning Off Multiple Areas with Disarm All ....... 80
CHG SKEDS ? (COMMAND + 5 + 2) ................... 51
Bosch Security Systems | 12/15 | F01U036089-04
3
D1260/D1260B | Owner's Manual Contents
♦ User (Token) Worksheet (User 000 to 038)
D9412x/D7412x Only ........................................ 87
User (Passcode) Worksheet (User 039 to 075). 88
♦ User (Token) Worksheet (User 039 to 075)
D9412x/D7412x Only ........................................ 89
Figure 6:
Escape Route ................................ 103
Tables
Table 1:
D1260/D1260B Keypad keys............. 7
User (Passcode) Worksheet (User 076 to 114)
(101-249 = D9412x only) ................................... 90
Table 2:
Keypad Commands ......................... 16
Table 3:
Door Status ..................................... 46
♦ User (Token) Worksheet (User 076 to 114)
D9412x/D7412x Only (101-249 = D9412x only) 91
Table 4:
Sked Table ...................................... 53
Table 5:
Screen Area Definitions .................. 76
User (Passcode) Worksheet (User 115 to 150)
(101-249 = D9412x only) ................................... 92
User (Token) Worksheet (User 115 to 150) (101249 = D9412x only) ........................................... 93
User (Passcode) Worksheet (User 151 to 189)
(101-249 = D9412x only) ................................... 94
User (Token) Worksheet (User 151 to 189) (101249 = D9412x only) ........................................... 95
User (Passcode) Worksheet (User 190 to 226)
(101-249 = D9412x only) ................................... 96
♦ User (Token) Worksheet (User 190 to 226)
D9412x/D7412x Only (101-249 = D9412x only) 97
User (Passcode) Worksheet (User 227 to 249)
(101-249 = D9412x only) ................................... 98
User (Token) Worksheet (User 227 to 249) (101249 = D9412x only) ........................................... 99
User (Passcode) Worksheet (Blank) ............... 100
User (Token) Worksheet (Blank) ..................... 101
Security System Limitations ............................ 101
Fire Safety and Evacuation .............................. 102
Standard Displays ............................................ 103
System Trouble Displays ................................. 104
Security System Glossary ................................ 106
Maintenance and Service ................................ 107
How to Clean the Command Center ................ 107
Your Alarm Company ....................................... 107
Figures
Figure 1:
D1260/D1260B front panels ............. 5
Figure 2:
D1260/D1260B Digital Keypad .......... 6
Figure 3:
Using soft keys for display menus ..... 6
Figure 4:
Smoke Detector Locations (Plan
View) .............................................. 102
Figure 5:
Smoke Detector Locations (Elevation
View) .............................................. 102
4
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Contents
Introduction
Your security system helps to secure life, property, and investments against fire, theft, and bodily
harm. The keypad is an advanced digital device that offers a variety of features not available with
other systems. Its highly visible, backlit keypad and built-in sounder alert you to a number of system
events. A familiar ATM style design and ease-of-use make it ideal for property monitoring.
Your Keypad
Your Keypad is composed of two main sections: the numeric keypad section and the display/selection
keys (also referred to as “soft keys”).
Figure 1: D1260/D1260B front panels
D1260B 2
1
D1260
1
4
#
4
3
1 - LCD Display
3-
2 - Digital Keypad
4 - Keypad Function Keys
Bosch Security Systems | 12/15 | F01U036089-04
Soft Keys
5
D1260/D1260B | Owner's Manual | Introduction - About This Owner’s Manual
The numeric keypad section is a standard 3x4keypad matrix that should be very familiar to you.
It has been designed to closely resemble that of a
standard telephone with the numeric keys of 1-0;
and * and # keys. The display is an easy-to-read 4
line by 20-character liquid crystal display that
becomes backlit when a key is pressed or a
system event occurs.
About This Owner’s Manual
This owner’s manual is divided into five main
sections:
•
•
Figure 2: D1260/D1260B Digital Keypad
#
D1260
•
D1260B
The soft keys are used to make selections when
the display shows an arrow pointing next to it.
For example, the display shown to the right is
what will appear when there are faulted points in
your system. Pressing the soft key adjacent to
the View Points> display will then begin to scroll
the faulted point(s) in your system.
Figure 3: Using soft keys for display menus
•
•
6
Security System Basics: Covers how to use
the Keypad, the various keys on the Keypad,
what a “Point” is and the various types of
Points, and custom displays.
System Commands: This section covers
system commands, such as turning the
system on and off, resetting sensors, etc.
Your security company programs the
functions described in this section. Some of
them may not be included in your system.
Some of the functions covered may require
you to enter your personal passcode.
Advanced Commands: Allow users to
perform advanced system functions like add
and delete user passcodes, reassign authority
levels to user passcodes and operate or
change programmed scheduled events
(Skeds) from the keypads. As you make
changes to the system, update the
information contained in the tables in this
guide to provide an accurate account of the
programmed information.
Multi-Area Use: Each of the functions
described in the preceding section on
Advanced Commands is presented as though
your system includes only one area. If your
system includes more than one area, it can be
set up one of two ways by the installing
company: (1) Each keypad will only have
access to the local area to which it is
assigned, or (2) Each keypad may access
either some or all areas beyond the one to
which it is assigned.
Appendix: Covers the limitations of a
Security System, Fire Safety and Evacuation,
Maintenance and Service of your Security
System and How to Clean the Keypad.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part I: Security system basics
Part I: Security system basics
Using the keypad
Your security system provides quick access to
functions by pressing the COMMAND key and
one or two additional keys.
D1260
D1260B
Another way to access functions is through the
Command Menu. To access the Command Menu,
press the soft key adjacent to Menu> shown in
the display.
Pressing the soft key adjacent to the function
being displayed initiates the function.
To exit the Command Menu, press the <Exit soft
key.
Use the Command Menu to locate functions you
don’t use often or that don’t have a command
number.
Pressing the <Previous or Next> soft key while in
the Menu List allows you to scroll up or down
through the list of functions programmed by your
security company.
Command center keys
Table 1: D1260/D1260B Keypad keys
Key
D1260
#
Name
Description
COMMAND
Use the COMMAND key in combination with one or two numeric keys to
perform a function
ENTER
The ENTER key is used to complete the entry of your passcode at the
command enter. Whenever a function requires that you enter your
passcode at the keypad, first press the digits of the code and then
press the ENTER key. Your system will not recognize your passcode
until you press ENTER.
EXIT
When Exit> or <Exit appears in the keypad display, pressing the soft key
adjacent to it will bring you one level up in the function or will exit you
out of the function you are in. These functions may be displayed on
either side of the display.
Previous
When viewing a list, pressing the <Previous soft key will take you back
to the previously shown item.
Next
Press the Next> soft key to pass over the present item(s) in a menu or
function.
D1260B
Bosch Security Systems | 12/15 | F01U036089-04
7
D1260/D1260B | Owner's Manual | Part I: Security system basics - Points
Points
Fire alarms have a unique audible warning signal.
What is a Point?
A “point” is a detection device, or group of
devices connected to your security system.
Points display individually at the keypad with
custom text. The text can describe a single door,
motion sensor, smoke detector, or an area such
as UPSTAIRS or GARAGE. There are two basic
types of points, controlled and 24-hour.
Controlled Points
Controlled points respond to alarm conditions
depending upon whether the system is turned on
(armed) or turned off (disarmed). Controlled
points are programmed to respond instantly to
alarm conditions or to provide a delay for you to
reach the keypad and disarm the system.
The type of alarm appears before the point text
when there is an alarm. There are two types of
controlled points, perimeter points and interior
points.
Non-Fire Points
Non-fire 24-hour points are always armed and
cannot be disarmed.
Your Custom Display
“At an idle state” means that the system is not
currently performing a function entered by a
user. There are three idle states the system may
be in:
•
•
•
Turned on (Armed)
Turned off (Disarmed) with no points faulted
(doors or windows open) in the area
Turned off with faulted points (doors or
windows open) in the area.
Perimeter Points
These points usually include all exterior doors
and windows of the building.
Interior Points
These points usually include interior forms of
burglary detection devices, such as motion
sensors, or inside doors, for example.
24-Hour Points
24-hour points are always on, even when the
burglary system is disarmed (turned off). There
are two types of 24-hour points, fire points and
non-fire points.
Fire Points
Fire points exclusively monitor fire detection
devices. They are always armed and cannot be
disarmed. You can clearly distinguish fire points
from other non-fire points at the keypad.
When there is a fire alarm, the display shows the
following:
*FIRE ALARM* is displayed on the first line, text
identifying the point as a fire point is displayed
on the second line, and instructions for silencing
the alarm are displayed on the third and fourth
lines.
8
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part I: Security system basics - View Faulted or Bypassed Points
This manual uses the default idle state displays for examples of these idle states. Your security
company may have programmed custom text for the idle displays in your system. The custom text and
the default text for the three system idle displays follow.
Default Text
Area Name Text
Custom Text
________________
Appears on the top line of the
display
Throughout this manual, all examples of “AREA # NAME TEXT” will use “AREA 1
WAREHOUSE.” The actual name of Area 1 will differ depending on the specifics of your
system.
Area Is On Text
________________
The Silence> soft key is only shown when the keypad buzzer is active
Area Off Text
________________
Indicates the area is turned off
(disarmed). 24-hour points
remain armed.
Area Not Ready Text
________________
Indicates that the area is turned
off, but not ready to arm.
View Faulted or Bypassed Points
To properly arm your system, all the doors and
windows in the system must be in the normal
(not faulted) condition. Viewing the faulted
points helps you find faulted points and correct
them so proper arming is possible.
Your keypad offers two ways of displaying faulted
and bypassed point information. The first causes
the faulted or bypassed point information to
scroll automatically through the display. The
second allows you to manually scroll through
each individual point description.
Bosch Security Systems | 12/15 | F01U036089-04
To automatically scroll faulted or bypassed
points
1. Ensure your keypad shows idle text.
The View Points> soft key may be displayed
on the third line of the keypad if there are
faulted points.
2. Press any number key. The text for Area 1 is
displayed first followed by the number (#) of
faulted points on the next line
9
D1260/D1260B | Owner's Manual | Part I: Security system basics - Warning Displays and Tones
3. The display changes to show the point text
description of the faulted points. If there is
more than one faulted point, the display will
automatically cycle through all of them before
returning to idle text.
These displays scroll at the rate of 3 seconds
each.
Warning Displays and Tones
Your keypad emits one of several distinct tones
and displays custom text to alert you to system
events. Additional bells or sirens may also be
connected to your system. Bells or sirens
mounted on the exterior of your premises alert
neighbors to emergencies and provide an audible
guide for police and fire fighters.
Keypad Quiets for Keystrokes
4. The display returns to idle text after scrolling
through the faulted and bypassed point
information.
Pressing any key on the keypad lights the keys
and quiets any warning tones. If you don’t press
another key within 20 seconds, the keypad lights
go out and the warning tones resume.
Priority of Events
If more than one event occurs, your system sorts
them into one of four groups. The groups
(highest priority first) are:
The View Points> soft key will be shown
when there are faulted points.
To manually scroll faulted or bypassed points:
1. Ensure your keypad shows idle text.
2. Press the View Points> soft key to display
the first faulted point.
•
•
•
•
Fire Alarms
Burglary Alarms
Fire Troubles and Fire Supervisory conditions
Non-Fire Troubles and Non-Fire Supervisory
conditions.
The group with the highest priority scrolls first in
the keypad’s display. Descriptions of the tones
and displays for each group and instructions for
silencing the tones are included in the
descriptions that follow.
Press the Next> soft key or the <Previous
soft key repeatedly to display the faulted and
bypassed point information.
If faulted or bypassed points in other areas
exist, then the display changes to show these
points before returning to idle text.
10
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part I: Security system basics - Fire Alarms
Fire Alarms
Fire alarms are the highest priority events. When
a fire point activates, your keypad emits a
pulsating high-pitched fire tone. Evacuate all
occupants and investigate for smoke or fire.
Ensure that all occupants know the difference
between the burglary tone and the fire tone. The
tone sounds for the time set by your security
company.
Silencing Fire Alarms
Your system may be programmed so that you
cannot silence some fire alarms until the fire
event clears. Entering COMMAND 4 clears the
scrolling point text from the display.
The *Alarm Silenced* message will continue to
alternate with idle text as a reminder that it is
still possible to view the text of the points in
alarm by using the View Memory function. See
VIEW MEMORY ? (Command 40) for more
information.
Entering a personal passcode with the proper
authority level silences a fire alarm and disarms
the system if it was armed.
The system will now display *Alarm Silenced* on
the second line and Clear Display> appears on
the fourth.
To clear the event memory and remove the
*Alarm Silenced* message from the display,
press the Clear Display> soft key.
The display will show the instructions for clearing
the message. Enter a valid passcode and press
the Clear> soft key.
Then the number of points in alarm (# FIRE
ALARMS) and then the area text appears (AREA 1
NAME TEXT) followed by the custom text of all the
points in alarm (SMOKE DETECTOR), in the order of
occurrence.
If there is more than one point causing an alarm, the
display will show each point for three seconds
before showing the next one.
If a fire trouble still exists after acknowledging
the alarm, the display shows Fire Trouble.
When the last alarm is shown, the next display is
the idle text. The cycle is repeated until COMMAND
4 is pressed.
3 seconds
3 seconds
3 seconds
To remove this display, the fire point(s) must be
returned to normal. If you wish to review cleared
events, use COMMAND 40.
3 seconds
Bosch Security Systems | 12/15 | F01U036089-04
11
D1260/D1260B | Owner's Manual | Part I: Security system basics - Burglary Alarms
Burglary Alarms
Silencing Burglary Alarms
Burglary alarms are the second priority. When a
burglary point activates while your system is
armed, your keypad emits a steady high-pitched
burglary tone. The tone sounds for the time set
by your security company.
Entering a personal passcode with the proper
authority level silences a burglary alarm and
disarms the system if it was armed.
The system will now display *Alarm Silenced*
The keypad display shows the number of burglary
points activated, the point text then idle text.
and then the number of points in alarm ###
Alarms and the custom text of all the points in
alarm, in the order of occurrence.
If there is more than one point causing an alarm,
the display will show each point for three
seconds before showing the next one. When the
last alarm is shown, the next display is idle text
followed by the first alarm
Entering COMMAND 4 clears the scrolling point
text from the display.
The *Alarm Silenced* message will continue to
alternate with idle text as a reminder that it is
still possible to view the text of the points in
alarm by using the View Memory function. See
VIEW MEMORY ? (Command 40) for more
information.
3 seconds
3 seconds
3 seconds
3 seconds
To clear the event memory and remove the
*Alarm Silenced* message from the display,
press the Clear Display> soft key.
The display will show the instructions for clearing
the message. Enter a valid passcode and press
the Clear> soft key.
12
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part I: Security system basics - Fire Trouble and Fire Supervisory Events
Fire Trouble and Fire Supervisory
Events
When a fire trouble or fire supervisory condition
occurs, your keypad emits three warble tones,
then a pause (repeatedly).
The system displays the number of fire points
that are in a trouble or supervisory condition as
well as the point text of the affected points.
Some fire points, when tripped, will
display FIRE TROUBLE for a preset
amount of time. If no other fire
activity is detected, this condition
will automatically clear. If the
condition remains or another fire
detector is tripped, a fire alarm will
occur.
Viewing Fire Trouble and Fire Supervisory
conditions
Silencing Fire Trouble and Fire Supervisory
conditions
Pressing COMMAND 4 or the Silence> soft key
silences the conditions. In addition to this,
entering a personal passcode with the proper
authority level silences the condition and disarms
the panel if it was armed. If you wish to review
these cleared troubles, using COMMAND 40 can
do this.
Some systems may be programmed
to automatically re-sound the
keypad’s trouble tone after a period
of time if the fire trouble or fire
supervisory condition remains.
Consult your security company for
further information.
Special Fire Trouble and Fire Supervisory
Display
If you silence the keypad or clear a trouble or
supervisory condition for a Fire Point from the
display and the fire point remains in trouble, Fire
Trouble or Fire Supervisory appears in the
keypad’s display. This remains in the display until
the condition causing the trouble is cleared.
Bosch Security Systems | 12/15 | F01U036089-04
After pressing COMMAND 4 or entering your
passcode, the text of the fire point in trouble
continues to automatically scroll through the
display. Press View Points> soft key and then
Next> soft key to scroll these displays manually if
you wish. Events scroll in chronological order.
Non-Fire Trouble and Supervisory
Events
When a trouble event occurs, your keypad may be
programmed to emit three warble tones, then a
pause (repeatedly).
If the system was armed the keypad display
shows the number of non-fire trouble events or
non-fire supervisory events and then custom text
for each activated point.
Silencing Non-Fire Trouble and Supervisory
Events
Pressing COMMAND 4 or the Silence> soft key
silences the Trouble and/or non-fire Supervisory
conditions. In addition to this, entering a
personal passcode with the proper authority level
silences a trouble and disarms the panel if it was
armed. Press the View Points> soft key then the
Next> soft key to scroll these displays manually.
If you wish to review these cleared troubles, use
COMMAND 40 to do this.
13
D1260/D1260B | Owner's Manual | Part I: Security system basics - Special System Trouble Display
Special System Trouble Display
Exit Delay Tone and Display
These displays appear on all keypads in the
system. See Standard Displays for a description of
each system trouble display. Entering your
passcode, COMMAND 4 or pressing the Silence>
soft key will silence a system trouble tone, but
the System Trouble display will not clear until the
faulted condition is corrected.
After you arm your system, the keypad emits a
repeating beep tone, displays AREA 1 NAME
TEXT is now arming… then
A system trouble display begins by sounding a
trouble tone and then three seconds later the
specific System Trouble Display is shown, such
as Service AC Fail.
EXIT NOW! and counts down the exit delay time.
Keystroke Checking Tones
Valid Entry
Some system may be programmed to
not initiate a trouble tone during
these conditions.
Cleared Events Are Not Lost
If you clear the alarms and troubles from the
display, you can still view all the events that
occurred since the last time the system was
armed by using COMMAND 40 (View Event
Memory).
Entry Delay Tone and Display
When you enter an armed system through a point
programmed for entry delay, the keypad emits a
repeating warble tone and displays the following
to remind you to turn off your security system.
If you press an appropriate key for the function
or entry you desire, the keypad emits a muted
beep tone, indicating it accepted your keystroke.
Invalid Entry
A flat buzz tone sounds when you perform a
function that is not allowed or when the keypad
has no information to display.
Silencing an Alarm
The audible alarm sounds for a specific period of
time before it automatically shuts off. If an alarm
occurs and you want to silence the siren before
the time expires, simply enter your personal
passcode and press ENTER.
To SILENCE an alarm:
Enter your passcode and press ENTER
.
If you fail to turn off the security system before
the entry delay time expires, it may sound the
burglary tone and may also send an alarm report
to your security company.
14
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part I: Security system basics - Silencing an Alarm
How Your System Reports Alarms
Your security system may be programmed to
automatically disconnect your telephones when
sending reports to your security company. Once
the report is completed, your security system
returns the telephones to normal operation
(check with your security company). Other
methods of communicating alarm conditions are
also available. Please consult your security
company for services available in your area.
Your system makes repeated attempts to send
reports to your security company.
In the event your security system fails to
communicate, the keypad sounds a Trouble Tone
and displays AREA 1 WAREHOUSE Comm Fail
Route Grp1 (where the Route Group can be 1, 2,
3, or 4):
Notify your security company of the
communications failure.
If your system uses telephone lines
as its means of communication and
telephone service is interrupted,
your security system cannot send
reports to your security company
unless it has an alternate means of
transmitting them.
Bosch Security Systems | 12/15 | F01U036089-04
15
D1260/D1260B | Owner's Manual | Part II: System Commands - Silencing an Alarm
Part II: System Commands
Below is a summary of the commands covered in
this section.
Some of these functions may not be
available in your system. Please
consult your security company to
determine which commands have
been made available to you.
If you attempt to enter a function that’s not
available or if the function is available in the
system but your passcode is not authorized to
perform the function, then **No Authority** will
display on the Keypad.
Table 2: Keypad Commands
COMMAND
Function
Master Arm
+
Master Arm Instant
Perimeter Instant
Perimeter Delay
Silence Trouble Sounder & Clear
Trouble Display
+
+
+
View Memory
Walk Test
Reset Sensors
Watch Mode
Press the COMMAND key and then the one or
two digits shown in the table below to perform
the function. When you use a command to
perform a function, the displays in the function
list below do not appear at your keypad.
Special Alert
Perimeter Partial
Special Alert
+
Walk Test
Some commands listed below may
not be available. Contact your
security company for more
information.
16
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - Entering a Passcode
Entering a Passcode
1. The display may prompt you to enter your
passcode.
and the exit delay tone begins. After exit
delay time expires,
the display changes to idle armed text.
2. The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all passcode digits (from
a minimum of 3 to a maximum of six) are
entered.
Turning Off the System (Disarming)
3. Press ENTER.
Turning On the System (Arming)
Your security system can be turned on (armed) in
many different ways, depending on the arming
command used. Arming Commands are those
commands used to turn on the system. The most
basic arming command is to arm the entire
system. The simplest way to arm your system is
to enter your personal passcode or press
[COMMAND] [1].
There are several other arming commands to turn
on the system. These are described later in this
manual.
Entering your personal passcode turns off your
security system. When the system is turned on,
you must enter through a designated entry door
to prevent an instant alarm condition. Opening
the door starts entry delay time and the Keypad
emits a pulsing “beep” tone to remind you to
turn off the system. Enter your passcode before
the delay time expires and the system will turn
off.
If you enter through the wrong door or fail to
disarm before the entry delay time expires, you
will cause an alarm.
If this happens, silence the alarm (by entering
your personal passcode and pressing ENTER)
and call your security company to let them know
that it is not an emergency situation.
To Turn Your Security System On (Arm):
1. Enter your passcode and press ENTER.
2. The keypad briefly displays AREA 1 NAME
TEXT is now arming…,
Bosch Security Systems | 12/15 | F01U036089-04
17
D1260/D1260B | Owner's Manual | Part II: System Commands - Turning On the System (Arming) With a
Duress Passcode
To Turn Your Security System Off (Disarm):
2. The display shows Check Area #.
1. Enter your passcode and press ENTER.
2. You must press the ENTER key within 5
seconds of entering your passcode, or the
passcode entry will be invalid.
3. One of the messages below may display in
place of Check Area #.
3. The display returns to idle disarmed text.
Turning On the System (Arming) With a
Duress Passcode
Indicates the system is programmed not to
arm with particular points faulted (doors or
windows open).
Your passcode may have a special duress feature
that is simply your personal passcode with its
last digit increased by 1 or 2.
If an intruder demands that you arm or disarm
the security system, you can use your duress
passcode. The duress passcode arms or disarms
the system and sends an alarm report to your
security company. There is no alarm tone or
visual indication at the premises that the report
is sent. Check with your security company before
attempting to use this feature.
Indicates that the system’s number of
allowable bypassed points has been reached.
Your system’s maximum number of bypassed
and/or force armed points is set by your
security company. Check with them to learn
this number.
Turning On the System (Arming) With
Doors or Windows Open
If a protected door or window is open, you may
have the option of “force arming” with that point
faulted. Faulted points (opened doors or
windows) that are force armed are not included
in the system. The remaining points arm
normally.
Force armed points either return to normal
operation after you turn off your system or return
to normal when the door or window is closed.
Your system might not offer force arming or it
may be restricted to specific points. Contact your
security company for more information.
Indicates that more than the number of
allowable points are faulted. Bypassed points
are counted as faulted. Your system’s
maximum number of bypassed and/or force
armed points is set by your security company.
Check with them to learn this number.
4. The display shows AREA 1 WAREHOUSE Not
Ready to Arm.
1. Use your passcode or an arming function to
start the arming process.
18
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - Turning On the System (Arming) With Doors
or Windows Open
5. Pressing the View Points> soft key will show
the specifics for any points that are faulted, if
any, and bypassed, if any.
Faulted points are displayed first then
bypassed points.
8. Once the last bypassed point is displayed,
the display will change to show the soft key
to either force arm the faulted points (Force
Arm>) or force arm the faulted/bypassed
points (Force/Bypass Arm>).
6. The display changes to show the number of
faulted points in the area.
Press Next> soft key repeatedly to scroll
through the point text for each faulted point.
9. Press the appropriate soft key to arm your
system with the faulted/bypassed points
removed from service.
If you do not want to go through the list of
faulted points and want to go directly to the
Force Arm> soft key or Force Bypass> soft
key, press the COMMAND button.
7. Once the last faulted point is displayed,
pressing the Next> soft key will start
displaying a summary and then specifics of
any bypassed points.
Bosch Security Systems | 12/15 | F01U036089-04
19
D1260/D1260B | Owner's Manual | Part II: System Commands - MASTER ARM ? (COMMAND + 1)
MASTER ARM ? (COMMAND + 1)
Description
Use this function to turn on the entire system,
both perimeter and interior. When you turn on
the system, the display shows how many seconds
of exit delay time you have to exit the protected
area. You should leave before exit delay time
expires.
Leaving after exit delay has expired will cause the
entry delay to start. You may also cause an alarm
on an interior device. Enter your personal
passcode to disarm the system.
This function may be used by your cleaning
service, a serviceman, or others who need to turn
on your system when they leave.
5. If your system is programmed to require a
passcode when performing a COMMAND 1,
the display prompts you to enter your
passcode.
The passcode is shown as asterisks (*).
6. If the passcode has valid authority for this
command, the display shows Exit now # (# =
exit delay time remaining) seconds
remaining.
Using Master Arm:
Using the COMMAND +1 shortcut
will only arm the area where the
keypad has been assigned. Example,
if the D1260 is assigned to Area 1,
only Area 1 will be armed when
COMMAND + 1 is pressed.
After the exit delay time expires, the display
changes to idle armed text.
1. The display shows disarmed idle text.
7. To disarm your security system, enter your
personal passcode and press ENTER.
Master Arming all Areas
2. Press the COMMAND key.
3. The display shows *System Command*.
If you prefer, you may use the Master Arm ?>
command in the Command Menu to initiate this
function which will arm all available areas
according to your authority level.
1. The display shows disarmed idle text.
4. Press the 1 key
2. Press the MENU> soft key to enter the
Command Menu,
3. then press NEXT> soft key repeatedly
20
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - MASTER ARM ? (COMMAND + 1)
4. until you reach the MASTER ARM ?> prompt.
Press the soft key.
5. The display may prompt you to enter your
passcode.
9. The next available area will appear with the
option to arm it.
Every time the Next>,<Previous or Arm> soft
keys are pressed, the display scrolls to the
next unarmed area.
The passcode is shown as asterisks (*) when
entered.
6. If there is more than one area that is set up,
the option is given to arm all of them with
MASTER ARM ALL ?
10. To arm all available areas, press the Arm>
soft key when the display reads Master Arm
All ?
11. The display changes to show that all areas
are arming.
or by pressing the Next> soft key…
Depending on what areas are armed or areas
that you have authority, 12345678 may or
may not appear.
to view each unarmed area and optionally
arm each one.
12. then displays Exit now # (# = exit delay time
remaining).
7. To arm a selected area, press Next> until the
desired area appears (Area name text along
with Arm Area # ?).
8. Then press Arm>
After the exit delay time expires, the display
changes to idle armed text.
13. To disarm your security system, enter your
personal passcode and press ENTER.
Bosch Security Systems | 12/15 | F01U036089-04
21
D1260/D1260B | Owner's Manual | Part II: System Commands -
14. The display changes to show that all the
areas are disarmed.
2. Press the COMMAND key. The display shows
*System Command*.
Depending on what areas are armed or areas
that you have authority, 12345678 may or
may not appear.
3. Press the 1 key. Now press the 1 key again.
4. The keypad display shows AREA 1
WAREHOUSE All On Instant.
The display returns to idle text.
5. To disarm your security system, enter your
personal passcode and press ENTER.
MASTER ARM INST ? (COMMAND + 1 +
1)
Use this function to turn on a single area, both
perimeter and interior without delays. When
entering COMMAND 11, remember that the
second 1 must be pressed within 2 seconds after
pressing the first 1.
The menu entry MASTER ARM INST> is different
in that it allows all or selected areas to be armed
instantly.
COMMAND 11 does not comply with
SIA CP-01 Standard.
Using the COMMAND + 1 + 1
shortcut will only instantly arm the
area where the keypad has been
assigned. Example, if the D1260 is
assigned to Area 1, only Area 1 will
be armed when COMMAND + 1 + 1
is pressed.
1. The display shows disarmed idle text.
22
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR INST (COMMAND + 2)
PERIMETR INST (COMMAND + 2)
Turn On the Perimeter With No Delays
Description
Use this function to turn on only the perimeter of
your building, leaving the interior of the building
disarmed. This function allows no exit or entry
delay time through the perimeter, including the
designated exit delay door.
This function is useful in residential systems
when everyone is home and ready to retire for
the evening. You can have the security of an
armed perimeter, yet move freely throughout the
interior of the premises.
It is also useful in commercial systems when you
are working before or after business hours and
wish to have the perimeter armed. Remember
there are no entry or exit delays when you use
this function. You must disarm (turn off) the
system to enter or exit the premises.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu,
then press NEXT> soft key
repeatedly.
until you reach the PERIMETR INST
?> prompt, then press the adjacent
soft key.
4. The display shows Perimeter On Instant.
Using Perimeter Inst:
1. Interior points are not armed with this
command and may remain faulted while
arming with COMMAND 2.
2. Press the COMMAND key.
The display shows *System Command*.
3. Press the 2 key.
After arming the perimeter without delays,
you cannot enter or exit the premises without
disarming the system. Opening a perimeter
door before disarming will generate an alarm.
If this happens, silence the alarm by turning
off your system and call your security
company to let them know that it is not an
emergency situation.
5. To disarm your security system, enter your
personal passcode and press ENTER.
The display then returns to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
23
D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR DELAY ? (COMMAND + 3)
PERIMETR DELAY ? (COMMAND + 3)
Turn On the Perimeter With Delays
4. The display shows Exit now! # (# = exit
delay time remaining).
Description
In residential systems this function allows you to
only arm the perimeter and exit through a door
programmed for exit delay. The interior of the
building remains disarmed. People or pets are
free to move throughout the interior of the
premises.
This function is also useful in commercial
systems when you are working before or after
business hours and wish to have the perimeter
armed. Other system users can enter through
doors programmed for entry delay, which will
start the entry delay sounder and countdown.
After the exit delay expires, Perimeter On
Delayed is displayed.
5. To disarm your security system, enter your
personal passcode and press ENTER.
Using Perimeter Delay
1. Interior points are not armed with this
command and may remain faulted while
arming with COMMAND 3.
The display then returns to idle text.
2. Press the COMMAND key.
The display shows *System Command*.
Silence the Trouble Sounder & Clear
Trouble Display (COMMAND + 4)
3. Press the 3 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu,
then press NEXT> soft key
repeatedly.
Description
Use COMMAND 4 to silence the trouble sounder
during system events. This command also clears
system messages from the display. If an alarm
has occurred and was silenced, the *ALARM
SILENCED* display will continue to scroll to
remind you that cleared events can be seen with
the View Memory function (refer to VIEW
MEMORY ? (COMMAND + 4 + 0) on page 25).
Using COMMAND 4:
1. The display shows disarmed idle text.
until you reach the PERIMETR DELAY
?> prompt, then press the adjacent
soft key.
24
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - VIEW MEMORY ? (COMMAND + 4 + 0)
Press the COMMAND key. The display shows
*System Command*.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
2. Press the 4 key.
3. The Keypad sounder is silenced.
Press NEXT> soft key repeatedly.
When you reach the VIEW MEMORY
?> prompt, press its adjacent soft
key.
VIEW MEMORY ? (COMMAND + 4 + 0)
View Event Memory
Description
Press ENTER.
Your system stores events that occurred since
the last time memory was cleared. Use
COMMAND 40 to view Event Memory.
Event Memory allows you or a service technician
to review events after they are cleared from the
keypad’s display. *ALARM SILENCED* will
continue to scroll to remind you that events are
stored in Event Memory.
Each time you turn on the system on, the Event
Memory is erased and the ALARM SILENCED
message is cleared.
4. Your system displays event summary lines
and point text in this order:
a. fire alarm summary line
b. point text for each fire alarm event
c. alarm summary line
d. point text for each alarm event
e. fire trouble summary line
Using View Memory:
f. point text for each fire trouble event
1. The display shows disarmed idle text.
g. trouble summary line
h. point text for each trouble event.
5. Press NEXT> to scroll through the events.
2. Press the COMMAND key. The display shows
*System Command*.
3. Press the 4 key and then the 0 key.
Bosch Security Systems | 12/15 | F01U036089-04
If there are no events to view, There are
currently no events in memory displays.
6. You can return to idle text at any time by
pressing Exit> soft key.
25
D1260/D1260B | Owner's Manual | Part II: System Commands - WALK TEST ? (COMMAND + 4 + 4)
WALK TEST ? (COMMAND + 4 + 4)
Walk Test
2. Press the COMMAND key. The display shows
*System Command*.
Description
Use this function to test keypads, detection
devices, and sounders (both interior and
exterior) to be certain they function properly. You
can review untested points at your keypad to
help pinpoint any problems.
You cannot arm your system while in the walk
test mode, and no alarm reports are sent to your
security company unless a 24-hour point is
activated (such as fire or panic). A Walk Test
Start Report may be programmed to be sent to
your security company.
Upon initiation, the walk test will test the
burglary bell pattern on the bell output and ring
the keypad burglary bell for 2 seconds. The AC
will be disabled for 4 minutes in order to test the
system’s battery power. If the battery cannot
maintain the system for the 4-minute period, the
keypad will appear to go dead. If your keypads
are programmed to be supervised, the main
alarm panel will beep intermittently during this 4minute period. If this happens, contact your
security company. At the end of the 4-minute
period, AC is returned to the system and the
panel restores. To test individual detection
devices, simply activate sensors and open
protected doors and windows one-at-a-time. As
each detection device is faulted, the Keypad
emits a brief tone and the display indicates for
60 seconds that the point has been tested. This
verifies that each detection device is working
properly.
3. Press the 4 key and then the 4 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the WALK TEST ?>
prompt, press its adjacent soft key.
Press ENTER.
4. The burglary bell sounds for 2 seconds. When
the display shows ### points remain to be
tested (### is the number of points) you can
begin.
Using Walk Test:
1. The display shows disarmed idle text.
If you know the point number, you
can enter it by pressing its number
key and then the ENTER key
The display will change to show the
point that was entered. If the point
is invalid the message “Invalid Point”
or “This is not a valid walk point”
appears.
26
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - RESET SENSORS ? (COMMAND + 4 + 7)
Test each point by first opening and then
closing the door or window or other
detection device.
Check the display after testing each point.
For interior points, walking past the device
once is sufficient. If any point does not test
correctly, contact your security company for
service.
The display momentarily shows All points
have been tested.
The displays then shows idle text.
5. During the Walk Test you may want to see the
points that remain untested by pressing the
View untested pts> soft key.
The display shows ### points untested.
RESET SENSORS ? (COMMAND + 4 +
7)
Reset Sensors
Description
Press the Next Pt> or Prev Pt> soft keys to
see information about specific points that
have not yet been tested.
6. Move through this list by pressing the Next
Pt> soft key.
Detection devices, such as smoke detectors and
shock sensors, must be reset after being
activated. This function momentarily removes
power from these sensors to reset them.
It also clears point information from the display,
leaving the *ALARM SILENCED* message in the
display as a reminder that the View Memory
function can be used to view the cleared point
information.
The display changes to show the information
for that point.
Press the Exit> soft key to return to the ###
points remain to be tested screen before
continuing with the walk test.
7. When all points have been tested, 0 points
remain to be tested is displayed.
To clear the event memory and remove the
*Alarm Silenced* message from the display,
press the Clear Display> soft key.
Press the <Exit soft key.
Bosch Security Systems | 12/15 | F01U036089-04
27
D1260/D1260B | Owner's Manual | Part II: System Commands - RESET SENSORS ? (COMMAND + 4 + 7)
The display will show the instructions for clearing
the message. Enter a valid passcode and press
the Clear> soft key.
Arming the system will also clear the display and
the event memory.
4. The display shows for approximately 15 to 20
seconds.
The display then shows retrieving the panel
information.
Using Reset Sensors:
1. The display shows disarmed idle text.
The display then returns to show idle text.
2. Press the COMMAND key. The display shows
*System Command*.
3. Press the 4 key, followed by the 7 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
If you enter this function and the detector or
sensor resets momentarily, but then returns to a
faulted condition, the conditions causing the
activation may still be present or the detector
may be faulty. Check to be certain that there is
no smoke, fire, or other danger present. If you
can’t reset the detector or sensor contact your
security company.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the RESET
SENSORS ?> prompt, press its
adjacent soft key.
Press ENTER.
28
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - WATCH MODE ? (COMMAND + 6)
WATCH MODE ? (COMMAND + 6)
Watch Mode
Description
With your security system disarmed, you can use
watch mode to monitor some points. Each time
some points are faulted (door or window is
opened) the keypad chimes once and displays
the point text for 60 seconds. No alarms are
generated by this mode except 24-hour alarms
(fire, panic, etc.).
When the keypad’s keypad lighting is on, the
keypad does not chime. The keys light for 20
seconds whenever you press a key.
Use this function in residential systems to
monitor entries or exits in your home. In
commercial systems it can serve as a door chime
to alert you when a customer or delivery person
enters your business.
Contact your security company to
find out which points are watch
points and whether or not your
system automatically turns the
Watch Mode on whenever you
disarm.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the WATCH MODE
?> prompt, press its adjacent soft
key.
Press ENTER.
3. The display briefly shows Watch Mode is now
on.
Entering Watch Mode:
1. The display shows disarmed idle text.
The display returns to show idle text.
Press the COMMAND key. The display shows
*System Command*.
2. Press the 6 key.
Bosch Security Systems | 12/15 | F01U036089-04
29
D1260/D1260B | Owner's Manual | Part II: System Commands -
Exiting Watch Mode:
1. The display shows disarmed idle text.
Press the COMMAND key. The display shows
*System Command*.
3. The display briefly shows Watch Mode is now
off.
The display returns to show idle text.
2. Press the 6 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the WATCH MODE
?> prompt, press its adjacent soft
key.
Press ENTER.
30
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR PART ? (COMMAND + 8)
PERIMETR PART ? (COMMAND + 8)
Partially Turn On the Perimeter
Description
This function is used to turn on the perimeter of
your building while selected portions of the
perimeter remain turned off. Perimeter points
that are not secure (faulted) when this function
is entered are automatically bypassed and are
not included in the system. This function does
not turn on the interior of your building.
Entry/exit delays are provided with this arming
command.
Use this function in residential systems to turn
on the front of your house while the interior and
the rear perimeter doors are left turned off,
giving you freedom of movement between the
house and patio.
In commercial systems, when you need access to
the large overhead doors to receive deliveries,
using this function will allow you to keep the rest
of the building perimeter armed.
Using Perimetr Part:
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the PERIMETR PART
?> prompt, press its adjacent soft
key.
Press ENTER.
3. The display prompts the user to exit the area
and starts counting down from 10 seconds to
arm the system.
1. The display shows disarmed idle text.
Press the COMMAND key. The display shows
*System Command*.
# is the number of seconds remaining,
counting down from 10 seconds, before the
system is armed.
4. When exit delay time expires and the system
turns on, the display shows:
2. Press the 8 key.
5. When performing a COMMAND 8 and no
points are faulted or if the points return to
normal before the exit delay time expires, the
system is turned on as in COMMAND 3.
6. To disarm, enter your personal passcode and
press ENTER.
Bosch Security Systems | 12/15 | F01U036089-04
31
D1260/D1260B | Owner's Manual | Part II: System Commands - Special Alerts (COMMAND + 7 and
COMMAND + 9)
Special Alerts (COMMAND + 7 and
COMMAND + 9)
Description
Commands 7 and 9 can be programmed to
respond to a choice of numerous situations that
may need immediate attention. They may also be
used to send a silent alarm to your security
company without sounding an alarm signal on the
premises. Check with your security company for
the options they offer.
3. Your COMMAND 7 special alert has been
programmed to:

notify your alarm company

ring a bell on your premises

display at your keypad
Description:
__________________________________________
__________________________________________
__________________________________________
Using COMMAND 7:
1. The display shows disarmed idle text.
Press the COMMAND key. The display shows
*System Command*.
2. Press the 7 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the USER CMD 7 ?>
prompt, press its adjacent soft key.
Press ENTER.
32
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part II: System Commands - Special Alerts (COMMAND + 7 and
COMMAND + 9)
Using COMMAND 9:
1. The display shows disarmed idle text.
Press the COMMAND key. The display shows
*System Command*.
2. Press the 9 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the USER CMD 9 ?>
prompt, press its adjacent soft key.
Press ENTER.
3. Your COMMAND 9 special alert has been
programmed to:

notify your alarm company

ring a bell on your premises

display at your keypad
Description:
__________________________________________
__________________________________________
__________________________________________
Bosch Security Systems | 12/15 | F01U036089-04
33
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - Advanced Commands
Part III: Advanced Commands
Use this section of the manual to perform advanced system functions like add and delete user
passcodes, reassign authority levels to user passcodes and operate or change programmed scheduled
events (Skeds) from the keypads. As you make changes to the system, update the information
contained in the tables in this guide to provide an accurate account of the programmed information.
Advanced Commands
Some commands listed below may not be available. Contact your security company for
more information.
Advanced
COMMAND
Function
Advanced
COMMAND
Function
Bypass a Point
+
Change Sked
+
Unbypass a Point
+
Delete Passcode
+
Test Report
+
Change Relay
+
Status Report
+
Change Passcode
+
Remote Program
+
Add Passcode
+
Change Time/Date
+
Default Text
+
Door Control
+
Fire Test
Access Level Change
+
Display Rev
+
Change Display
+
Move to Area
View Log
+
Extend Closing
View Point Status
Print Log
Terms Used in This Section
Listed below are some of the terms you’ll see throughout this section. Each term is covered in greater
detail later in this section and in Part II: System Commands.
Account
One or more areas reporting under a particular account number.
Area
A group of detection devices connected to your security system.
Arm and Disarm
To switch your burglar detection devices “on” and “off.” When the burglar
detection device is armed and is tripped, an alarm may be set off. When the
burglar detection devices are disarmed, the security system will not detect
intruders. Detection devices programmed as 24-Hour or Fire points are
always on.
Authority Levels
Levels of access authority assigned to passcodes.
Keypad
Arming station used to operate your security system.
Keypad Scope
Determines which areas a particular keypad can access.
34
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - Terms Used in This Section
Panel
The main control unit, which is locked in a steel enclosure. It sends data to
and receives inputs from the keypads.
Relays
Optional dry contact outputs that respond to system events.
Skeds
Functions programmed by your security company that occur at
predetermined times.
User Passcodes
A three to six digit number entered at a keypad to access the system.
Bosch Security Systems | 12/15 | F01U036089-04
35
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - BYPASS A POINT? (COMMAND + 0)
BYPASS A POINT? (COMMAND + 0)
Description
This command allows you to bypass points that
you do not want included in the system. Points
that are not included in the system do not detect
intruders and cannot send any reports. You can
bypass points when an area is disarmed.
Bypassing a point reduces the level of security
and should be used with discretion. Points
remain bypassed until you unbypass them or
some points may return when the area is
disarmed. See Unbypassing a Point (COMMAND
00).
You could use COMMAND 0 to leave a window
open over night without initiating an alarm. Also
see Turning the System On With Doors or Windows
Open.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the BYPASS A
POINT ?> prompt, press its adjacent
soft key.
Press ENTER.
Using Bypass a Point
1. The display shows disarmed idle text.
3. You will prompted for your passcode. It will
appear on the display as asterisks (*).
Press the COMMAND key. The display shows
*System Command*.
4. The display changes to show Enter point
number or press next key.
2. Press the 0 key.
36
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - BYPASS A POINT? (COMMAND + 0)
5. If a digit is pressed, the display shows Enter
point number: #. As soon as a digit key is
pressed, the display changes to Entering
point number:.
•
FRONT DOOR cannot by bypassed.
indicates the system is programmed not
to allow that point to be bypassed.
•
Invalid point Please try again. indicates
that the entered point doesn’t exist and
the display returns to allow another point
to be entered.
•
No additional points. indicates that there
are no more points that can be bypassed.
(# is the point number entered)
If you know the point number you wish to
bypass, enter the number and press the
Enter> soft key or the ENTER button.
If you don’t know the number of the point
you wish to bypass, you can view the list of
devices that can be bypassed by pressing the
Next> soft key.
Continuously pressing Next> scrolls through
the available points that can be bypassed.
When the point text of the point you wish to
bypass appears, press the Bypass> soft key.
One of the following messages displays
(FRONT DOOR is used here as an example):
• FRONT DOOR is not bypassed indicates
the point is not bypassed and the option
is given to bypass it.
•
FRONT DOOR is now bypassed. indicates
the point was successfully bypassed.
•
FRONT DOOR is already bypassed.
indicates that the point has already been
bypassed.
Bosch Security Systems | 12/15 | F01U036089-04
6. You can return to idle text by pressing <Exit.
7. If the bypassed point is a 24-hour point, the
message 24Hr Point Bypassed begins
alternating in the display with A1 AREA IS
OFF.
37
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - UNBYPASS A POINT? (COMMAND + 0
+ 0)
If the bypassed point is a Fire Point, the
message Fire Point Bypassed begins
alternating in the display with A1 AREA IS
OFF.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the UNBYPAS A
POINT ?> prompt, press its adjacent
soft key.
UNBYPASS A POINT? (COMMAND + 0 +
0)
Description
Unbypassing a point is a way to return a
bypassed point to the security system so that it
can once again respond to trouble and alarm
conditions.
Press ENTER.
3. You will prompted for your passcode. It will
appear on the display as asterisks (*).
Using Unbypass a Point:
1. The display shows disarmed idle text.
4. The display changes to show Enter point
number or press next key.
Press the COMMAND key. The display shows
*System Command*.
2. Press the 0 key twice.
38
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - UNBYPASS A POINT? (COMMAND + 0 +
0)
5. If digits are pressed, the display shows Enter
point number: #. As soon as a digit key is
pressed, the display changes to Entering
point number:.
•
FRONT DOOR is already bypassed.
indicates that the point has already been
bypassed.
•
FRONT DOOR cannot by bypassed.
indicates the system is programmed not
to allow that point to be bypassed.
•
Invalid point Please try again. indicates
that the entered point doesn’t exist and
the display returns to allow another point
to be entered.
•
No additional points. indicates that there
are no more points that can be bypassed.
(# is the point number that was entered)
If you know the point number you wish to
unbypass, enter the number and press the
Enter> soft key or the ENTER button.
If you don’t know the number of the point
you wish to unbypass, you can view the list of
devices that can be unbypassed by pressing
the Next> soft key.
Continuously pressing Next> scrolls through
the available points that are currently
bypassed.
When the point text of the point you wish to
unbypass appears, press the Unbypass> soft
key.
One of the following messages displays
(FRONT DOOR is used here as an example):
• FRONT DOOR is not bypassed indicates
the point is not bypassed and the option
is given to bypass it.
6. You can return to idle text by pressing <Exit.
•
FRONT DOOR is now bypassed. indicates
the point was successfully bypassed.
Bosch Security Systems | 12/15 | F01U036089-04
7. If you are attempting to unbypass a 24-Hour
or Fire Point that is still faulted, the keypad
will display Cannot unbypass 24hr faulted
points.
39
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SEND REPORT ? (COMMAND + 4+1 or
4+2)
SEND REPORT ? (COMMAND + 4+1 or
4+2)
Description
This function tests the communication link
between your security system and your security
company. It is an important part of maintaining a
high level of security for your property.
Two types of test reports may be sent. The first
type of report is a simple test report (Command
41). The second type of report is a status report
(Command 42). This status report indicates the
current condition of your system.
Using Send Report
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the SEND REPORT
?> prompt, press its adjacent soft
key.
1. Always call your security company before
sending a test report.
2. The display shows disarmed idle text.
Another menu appears allowing for
the selection of sending a test report
(Test Rpt?>) or a status report
(Status Rpt?>). Press either one of
the adjacent soft keys.
Press the COMMAND key. The display shows
*System Command*.
3. Press the 4 key then the 1 key to send a test
report.
4. The keypad displays Sending report… Please
wait… until the report is transmitted to the
security company.
Press the 4 key then the 2 key to send a
status report.
5. When the transmission is complete the
keypad displays Report sent for 5 seconds.
If the <Exit soft key is pressed before
5 seconds have elapsed, idle text will
be displayed.
40
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - REMOTE PROGRAM ? (COMMAND + 4 +
3)
The display returns to idle text.
For systems without a phone number
1. The display shows disarmed idle text.
6. If the test (or status) report doesn‘t
successfully transmit to the central station,
the keypad may sound a trouble tone and
display Comm Fail Route Grp# (# = 1-4) after
numerous unsuccessful attempts.
2. Call this phone number:
___________________________
This number is designated for the Remote
Account Manager.
You must make the call using the telephone
located at:
___________________________
REMOTE PROGRAM ? (COMMAND + 4
+ 3)
Description
This function allows the user to initiate Remote
Account Manager sessions. When the phone is
ringing at the panel, the user initiates this
function to have the panel seize the line.
Your security company can remotely program
your security system using the telephone line to
which your panel is connected. Typical remote
programming functions include: changing
personal passcodes, changing entry/exit delays,
resetting the system clock/calendar, and
adding/deleting system arming commands.
3. Identify yourself and your premises (account
number, name, address, etc.) and advise the
operator of the services you wish to have
performed. When the operator instructs you,
proceed to steps 4 and 5.
4. Press the COMMAND key. The display shows
*System Command*.
5. Press the 4 key then the 3 key.
6. Do not hang up the telephone.
Your security company may ask you to follow the
steps below to begin a remote programming
session. The time it takes to program the panel is
dependent on the number of changes made to
the program.
You’ll notice that two sets of procedures are
presented. The one you use will depend upon
whether your system has a pre-programmed
telephone number in its memory.


My system has a phone number
My system does not have a phone
number
Bosch Security Systems | 12/15 | F01U036089-04
41
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - REMOTE PROGRAM ? (COMMAND + 4
+ 3)
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
11. At the conclusion of the programming session
your system sends a report to the security
company and then returns your telephone to
normal service and your display to idle text.
Press NEXT> soft key repeatedly.
For systems with a phone number or network
connection
When you reach the REMOTE
PROGRAM ?> prompt, press its
adjacent soft key.
Press ENTER.
7. The display changes to show the two choices
that are available for connecting to RAM:
• Contact RAM: RAM via phone or network
• Answer Now
8. Press the Answer Now> soft key to connect
to RAM.


My system uses a phone number for
Remote Programming
My system uses an IP Address and
network connection for Remote
Programming
12. Ensure your keypad shows idle disarmed
text.
13. Press the COMMAND key. The display shows
*System Command*.
14. Press the 4 key then the 3 key.
When your security company is
communicating with your panel
during a RAM session, the D1260
may display Call for Service…
9. The display shows RAM connecting…
10. The security system will now disconnect
telephones sharing its telephone line during
the remote programming session. Hang up
the telephone now.
42
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - REMOTE PROGRAM ? (COMMAND + 4 +
3)
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
18. The display shows RAM connecting…
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the REMOTE
PROGRAM ?> prompt, press its
adjacent soft key.
19. The security system will now call the
telephone number or connect to the IP
Address specified for network connection
during the remote programming session.
20. At the conclusion of the programming session
your system sends a report to the security
company and then returns your telephone to
normal service and your display to idle text.
Press ENTER.
15. The display changes to show the two choices
that are available for connecting to RAM:
• Contact RAM: RAM via phone or network
• Answer Now
16. Press the Contact RAM> soft key to specify
the connection method to RAM.
17. Press either the RAM via phone> (to connect
the panel to the RAM software via a preprogrammed phone number) or RAM via
network> soft key (to connect the panel to
the RAM software via a pre-programmed IP
network address).
Bosch Security Systems | 12/15 | F01U036089-04
43
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHANGE TIME/DATE (COMMAND + 4
+ 5)
CHANGE TIME/DATE (COMMAND + 4 +
5)
The time and date in your system must be correct
for scheduled events to occur at the correct
times. Check the time at least once a month to
ensure accuracy. Use this function to set both
the time and date. The system uses a 12-hour,
AM/PM format. There is the option to
continuously display the time and date in place of
area status. The Time and Date will be shown
continuously until a new command is entered or
the current area’s status has changed. See
CHANGE DISPLAY (COMMAND + 4 + 9),
Time/Date Display for more information.
4. The display changes to Enter new time:
To just change the date, press the Set Date>
soft key, See Step 6.
If you input the wrong time, press the <Exit
soft key to clear the time.
Enter the new time using a 12-hour (HH:MM)
format.
Ex: If the desired time is 12:34, press 1 + 2 +
3+4
1. Ensure your keypad shows idle disarmed
text.
The Set Date> soft key will disappear
when the first digit is entered.
2. Press the COMMAND key. The display shows
*System Command*.
Press the Enter> soft key or the [ENTER]
button.
5. The display changes to show AM> or PM> soft
keys.
3. Press the 4 and then the 5 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press the AM> soft key to select AM.
Press the PM> soft key to select PM.
6. The display shows Enter new date:
Press NEXT> soft key repeatedly.
When you reach the CHG TIME/DATE
?> prompt, press its adjacent soft
key.
44
See Step 9 for use of the Time/Date Display>
soft key.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DOOR CONTROL (COMMAND + 4 + 6)
If you input the wrong date, press the <Exit
soft key to clear the time.
DOOR CONTROL (COMMAND + 4 + 6)
Description
There are three functions with the door control
function:
•
Enter the new date using a MM/DD/YY
format.
Ex: If the desired time is January 1, 2002,
press 0 + 1 + 0 + 1 + 0 + 2
•
•
Cycle Door – momentarily unlocks a door to
allow a person into an area
Unlock Door – unlocks a door to allow free
access
Secure Door – locks a door and prohibits
access regardless of a user’s authority level
Using Door Control
1. Ensure your keypad shows idle disarmed
text.
7. Press the Enter> soft key or the [ENTER]
button.
8. The Time/Date Display> soft key is used to
show how the time and date entered will
look.
9. The new time and/or date is displayed for 20
seconds before the display returns to idle
text.
2. Press the COMMAND key. The display shows
*System Command*.
3. Press the 4 key and the 6 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press the <Exit soft key to return to idle text.
Press NEXT> soft key repeatedly.
When you reach the DOOR
CONTROL ?> prompt, press its
adjacent soft key.
Bosch Security Systems | 12/15 | F01U036089-04
45
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DOOR CONTROL (COMMAND + 4 + 6)
4. The display will change and show a choice of
Cycle Door>, Unlock Door>, and Secure
Door>.
Press the adjacent soft key.
Cycle Door
The display changes to show that all the
doors are at a normal state except for Door 3,
which is cycled.
4. Enter another door number to cycle or press
the Exit> soft key to leave this function.
1. If you wish to momentarily unlock an access
door to allow a person into an area, press the
Cycle Door> soft key.
Unlock Door
2. The display will read *Cycle Door*1 2 3 4 5 6
7 8 if all door are at a normal state and are
available.
2. The display will read *Unlock Door*1 2 3 4 5
6 7 8 if all door are at a normal state and are
available.
If a door is not at a normal state, the number of
the door would be replaced with a symbol
indicated in Table 3.
Table 3: Door Status
Symbol
Meaning
-
Door is not active, in scope, or user does
not have access level authority.
C
Door is on timed door sequence.
U
Strike and shunt are latched active (held
open).
X
Strike and shunt are deactivated
(secured).
F
There is a problem with the door. Call
your security company.
3. Enter the number of the door you wish to
cycle then press the ENTER key. This door
will be cycled and the display will change to
reflect the new status of the doors.
1. If you wish to unlock an access door to allow
free access, press the Unlock Door> soft key.
If a door is not at a normal state, the number
of the door would be replaced with a symbol
indicated in Table 3.
3. Enter the number of the door you wish to
unlock then press the ENTER key. This door
will be unlocked and the display will change
to reflect the new status of the doors.
For example, if you wanted to unlock Door 3,
press 3 then press the ENTER key.
The display changes to show that all the
doors are at a normal state except for Door 3,
which is unlocked.
4. Enter another door number to unlock or
press the Exit> soft key to leave this function.
For example, if you wanted to cycle Door 3,
press 3 then press the ENTER key.
46
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - Access Level
Secure Door
1. If you wish to unlock an access door to allow
free access, press the Unlock Door> soft key.
2. The display will read *Secure Door*1 2 3 4 5
6 7 8 if all door are at a normal state and are
available.
2. Press the Menu> soft key to enter the
Command Menu.
3. Press Next> soft key repeatedly until you
reach the CHANGE LEVEL ?> prompt.
Press the adjacent soft key.
4. A prompt will appear asking for entry of the
Authority Level to be modified.
If a door is not at a normal state, the number
of the door would be replaced with a symbol
indicated in Table 3 on page 46.
3. Enter the number of the door you wish to
secure then press the ENTER key. This door
will be secured and the display will change to
reflect the new status of the doors.
For example, if you wanted to secure Door 3,
press 3 then press the ENTER key.
The display changes to show that all the
doors are at a normal state except for Door 3,
which is secured.
5. Enter the level number (1 – 14) and press the
Enter> soft key.
6. If the level entered is currently enabled, the
keypad will ask if you want to disable this
level.
(Level 14 is used here as an example.)
4. Enter another door number to secure or
press the Exit> soft key to leave this function.
7. If the level entered is currently disabled, the
keypad will ask if you want to enable this
level.
Access Level
This function is used to manually enable/disable
access authority levels assigned to users. It can
also be used to temporarily disable a user’s
access level instead of deleting and then readding the user.


I have this feature.
I do not have this feature.
(Level 14 is used here as an example.)
8. After selecting whether to disable or enable
the level, the display prompts you again to
enter an Authority Level to modify.
1. Ensure your keypad shows idle disarmed
text.
9. Press the <Exit soft key when you are
finished.
Bosch Security Systems | 12/15 | F01U036089-04
47
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHANGE DISPLAY (COMMAND + 4 +
9)
CHANGE DISPLAY (COMMAND + 4 + 9)
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
This function presents three options:
•
•
•
dim the display
brighten the display
continuously show the time and date in the
display.
Press the MENU> soft key to enter
the Command Menu.
Brighten/Dim Display
You can change your keypad’s display to make
the backlit LCD display bright or dim. When the
display is dim, the tones are softer than when the
display is bright. Use this option for keypads in
bedrooms where a brighter display and louder
tones could interfere with sleep.
If you dim the keypad backlit display and an
alarm or trouble condition arises, the display
automatically brightens and the volume
increases. The backlit display returns to dim
lighting when you clear the alarm or trouble
condition.
Press NEXT> soft key repeatedly.
When you reach the CHG DISPLAY ?>
prompt, press its adjacent soft key.
4. The display changes to show the display
options:
Show Continuous Time/Date
Use this function to replace the disarmed idle
text with a continuous time and date display and
to prevent a passersby from knowing the status
of your system.
Any time your keypad has an event to display, the
time and date display is automatically removed.
To return the time and date display, you must
perform this function again.
1. Ensure your keypad shows idle disarmed
text.
•
•
•
Bright Display> - Press to increase the
LCD’s backlit brightness. The backlight
adjustment will take effect after 20
seconds of inactivity.
Dim Display> - Press to decrease the
LCD’s backlit brightness. The backlight
adjustment will take effect after 20
seconds of inactivity.
Time/Date Display> - Press to
continuously show the time and date
instead of idle text.
2. Press the COMMAND key. The display shows
*System Command*.
If your system is turned on (armed),
you cannot display the time.
3. Press the 4 and then the 9 key.
48
To further adjust the LCD’s
brightness, the settings for the
Bright Display> and Dim Display>
soft keys can be changed by
accessing the Service Manual (99 +
Enter).
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - EXTEND CLOSING (COMMAND + 5 + 1)
EXTEND CLOSING (COMMAND + 5 + 1)
Your system may be programmed to expect you
to arm within a scheduled closing window, which
is a duration of time that is programmed by your
alarm company. Your system may also be
programmed to automatically arm at the end of
the window.
COMMAND 51 lets you extend the scheduled
closing window time either prior to the closing
window time or during the closing window time.
Use this function when you expect to stay past
the scheduled end of the closing window. Your
alarm company sets the length of time prior to
the start of the closing window in which you are
allowed to extend the closing window.
Close window is not currently active displays
during the time when the keypad won’t allow the
window to be extended.
If the alarm or trouble condition clears before the
end of the close window Please Close Now
message returns to the keypad display.
If you have not armed or extended closing, the
Please Close Now message and beep will
reappear after 10 minutes. Your alarm company
sets the length of time for the closing window. To
extend the window, enter the new time at which
you would like the reminder tone to begin. This
time will be the new beginning of the closing
window. The time length of the closing window is
programmed by your security company and
remains fixed.
When you hear the warning you can:
•
•
•
At the beginning of the closing window, the
keypad beeps and displays Please Close Now to
remind you to arm your system. It remains in the
display until you arm, the close window ends, or
you extend closing.
Press the Silence> soft key will silence the
beep and clear the message for 10 minutes
Leave before the end of the closing window
Stay past the scheduled end of the closing
window, by using COMMAND 51 to extend
the closing window.
Extending the closing window does
not effect the amount of time
available to close.
For example, if your closing window
starts at 4:00 p.m. and stops at 4:30
p.m. and you extend closing to 5:00
p.m., the closing window will now be
between 5:00 and 5:30 p.m.
The closing window can only be
extended once the window has
started.
Alarm or trouble messages replace this message
in the event of an alarm or trouble condition.
Pressing the Silence> soft key will silence the
beep and clear the message for 10 minutes.
Bosch Security Systems | 12/15 | F01U036089-04
49
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - EXTEND CLOSING (COMMAND + 5 +
1)
1. Ensure your keypad shows idle disarmed
text.
5. Enter the new time using a 12-hour (HH:MM)
format.
Ex: If the desired time is 12:34, press [1] [2]
[3] [4]
2. Press the COMMAND key. The display shows
*System Command*.
Press the AM> soft key to select AM.
Press the PM> soft key to select PM.
6. The display changes to show the new start
time briefly before returning to idle text.
3. Press the 5 key and then the 1 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
7. Press the Accept> soft key to accept the
Close Start time.
Press NEXT> soft key repeatedly.
When you reach the EXTEND
CLOSING ?> prompt, press its
adjacent soft key.
4. The display changes to show the current start
time.
Press the Change> soft key to change the
start time.
Press the Accept> soft key to accept the start
time and return to idle text.
50
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)
CHG SKEDS ? (COMMAND + 5 + 2)
Description
A Sked is a function programmed to be
performed automatically at a scheduled time by
your security system. You can change the
scheduled time for some functions, disable the
Sked and thus prevent it from automatically
happening or restart a previously disabled Sked.
Contact your security representative to
determine what Skeds may be programmed for
your system.
To change a Sked’s time, enable a Sked, or
disable a Sked, follow the procedure below to
first select the Sked from a list of Skeds
programmed for your system.
Using Chg SKEDS
1. Ensure your keypad shows idle disarmed
text.
2. Press the COMMAND key. The display shows
*System Command*.
3. Press the 5 key and then the 2 key.
Bosch Security Systems | 12/15 | F01U036089-04
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the CHG SKEDS ?>
prompt, press its adjacent soft key.
4. The number of the first Sked programmed
into your system is displayed, plus either its
time or an indication that it is disabled.
Press the Next> soft key to scroll through the
list of Sked numbers to find the one you wish
to change.
Your alarm system may be programmed with
up to 40 Skeds. If the Sked number being
displayed is not programmed, the keypad will
display Skd11 – No program. (11 is used as
an example).
51
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)
When an X appears in the Sked display, it is
an indication that “Except on Holidays” is
enabled.
•
Except on holiday>
Pressing this soft key will disable the
sked on holidays and change the first line
of the display to Skd 1 08:00am with
the X.
Specific holidays are programmed by your
security company.
When an * appears in the Sked display, it is
an indication that the Sked has or will
happen today.
Consult your security company and
determine which holidays have been
programmed in your system.
The display changes to allow a new time to
be entered.
5. If the Sked is currently enabled, the sked is
shown with Disable this sked> on the second
line. Press the adjacent soft key.
6. The display changes to show that the sked is
disabled.
Enter the new time using a 12-hour (HH:MM)
format.
Ex: If the desired time is 8:00, press 8 + 0 + 0.
If the Sked is currently disabled, the display
says Skd 1 is disabled.
Press the Enable this sked> soft key.
7. The display shows two soft keys:
Press the Enter> soft key or the ENTER
button.
8. If the time is a valid time, the keypad display
changes to show the new time with a
selection of AM or PM.
•
Only on holiday>
Pressing this soft key will enable the sked
only on holidays and change the first line
of the display to Skd 1 X 08:00AM
without the X.
Press the AM> soft key to select AM.
Press the PM> soft key to select PM.
9. The display shows the Sked with the new
time.
Press the <Exit soft key to return to idle text.
52
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)
Table 4: Sked Table
SKED #
Except
on
Holiday
Time
Date
Day of Week
SKED 1
Yes / No
SMTWTFS
SKED 2
Yes / No
SMTWTFS
SKED 3
Yes / No
SMTWTFS
SKED 4
Yes / No
SMTWTFS
SKED 5
Yes / No
SMTWTFS
SKED 6
Yes / No
SMTWTFS
SKED 7
Yes / No
SMTWTFS
SKED 8
Yes / No
SMTWTFS
SKED 9
Yes / No
SMTWTFS
SKED 10
Yes / No
SMTWTFS
SKED 11
Yes / No
SMTWTFS
SKED 12
Yes / No
SMTWTFS
SKED 13
Yes / No
SMTWTFS
SKED 14
Yes / No
SMTWTFS
SKED 15
Yes / No
SMTWTFS
SKED 16
Yes / No
SMTWTFS
SKED 17
Yes / No
SMTWTFS
SKED 18
Yes / No
SMTWTFS
SKED 19
Yes / No
SMTWTFS
SKED 20
Yes / No
SMTWTFS
SKED 21
Yes / No
SMTWTFS
SKED 22
Yes / No
SMTWTFS
SKED 23
Yes / No
SMTWTFS
SKED 24
Yes / No
SMTWTFS
SKED 25
Yes / No
SMTWTFS
SKED 26
Yes / No
SMTWTFS
SKED 27
Yes / No
SMTWTFS
SKED 28
Yes / No
SMTWTFS
SKED 29
Yes / No
SMTWTFS
SKED 30
Yes / No
SMTWTFS
SKED 31
Yes / No
SMTWTFS
SKED 32
Yes / No
SMTWTFS
SKED 33
Yes / No
SMTWTFS
SKED 34
Yes / No
SMTWTFS
SKED 35
Yes / No
SMTWTFS
SKED 36
Yes / No
SMTWTFS
SKED 37
Yes / No
SMTWTFS
SKED 38
Yes / No
SMTWTFS
SKED 39
Yes / No
SMTWTFS
SKED 40
Yes / No
SMTWTFS
Bosch Security Systems | 12/15 | F01U036089-04
Function
53
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DEL USER ? (COMMAND + 5 + 3)
DEL USER ? (COMMAND + 5 + 3)
This function allows a user to be deleted.
Enter the user number, not the passcode.
(123 is as an example.)
This function will delete the
passcode, Master User, and all subusers associated with the user
number.
1. Ensure your keypad shows idle disarmed
text.
Press either the Enter> soft key or the ENTER
button.
5. If the user number entered is a valid user in
the system, the display will show Delete User
123? Are you sure?
2. Press the COMMAND key. The display shows
*System Command*.
(123 is as an example.)
If the user number entered is not a valid user
in the system, the display will show This user
is currently not in use.
3. Press the 5 key and then the 3 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
6. Press the Yes> soft key to delete the user.
The display briefly shows that the user has
been deleted before returning to idle text
(123 is used as an example).
Press NEXT> soft key repeatedly.
When you reach the DEL USER ?>
prompt, press its adjacent soft key.
The user text is not deleted when
deleting a user. To modify a user’s
text, see Add/Change User
(Command 56).
4. The display changes to show Enter user # to
be deleted:
54
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG RELAYS ? (COMMAND + 5 + 4)
CHG RELAYS ? (COMMAND + 5 + 4)
Your security company may program relays for
automatic control and/or control from your
keypad of devices such as premises lighting or
entry gates. Contact them for further information
regarding the use of relays in your security
system.
1. Ensure your keypad shows idle disarmed
text.
2. Press the COMMAND key. The display shows
*System Command*.
4. The command center display changes
*Change Relay* Enter relay number:
Valid entries are 1 to 128, depending how the
system is configured.
Enter the relay number then press either the
Enter> soft key or the ENTER button.
5. If the relay is valid and turned off, the display
changes to Change Relay* Relay 123 is
currently off.
(123 is used as an example.)
3. Press the 5 key and then the 4 key.
Press the Turn on> soft key to turn on the
relay.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
6. If the relay is valid and turned on, the display
changes to Change Relay* Relay 123 is
currently on.
(123 is used as an example.)
Press the Turn off> soft key to turn off the
relay.
When you reach the CHG RELAYS ?>
prompt, press its adjacent soft key.
7. The display returns to the *Change Relay*
Enter relay number:
Press the <Exit soft key to return to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
55
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG PASSCODES ? (COMMAND + 5 +
5)
CHG PASSCODES ? (COMMAND + 5 +
5)
Description
Use this function to change your personal
passcode without assistance from the security
company.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Before you begin:
•
•
Choose a new passcode three to six digits
long. If you choose a passcode with the same
digit in consecutive order (for example “33”
in 334697), take care when entering it.
To avoid conflicting with other passcodes and
duress codes, your system does not let you
change passcodes to an existing passcode or
to within plus or minus 2 of an existing
passcode. For example, if 1234 were an
existing code, your system would not let you
change your code to 1232, 1233, 1234, 1235,
or 1236.
Using Chg Passcodes
1. Ensure your keypad shows idle disarmed
text.
2. Press the COMMAND key. The display shows
*System Command*.
Press NEXT> soft key repeatedly.
When you reach the CHG
PASSCODES ?> prompt, press its
adjacent soft key.
4. You will prompted for your passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the
asterisks.
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all passcode digits
are entered.
5. The display changes to Enter new passcode:
Enter the new passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the
asterisks.
3. Press the 5 key and then the 5 key.
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all passcode digits
are entered.
56
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)
6. Press the ENTER button.
If an invalid passcode is entered, the
command center will momentarily display
Passcode is already in use. Please try again.
7. If the new passcode is valid, the display
changes to Enter new passcode again:
ADD/CHANGE USER (COMMAND + 5 +
6)
Use this function to add or change a user to your
system without assistance from your security
company. You need to know which user numbers
are available, the authority level you want to
assign to the new passcode and the areas in
which it will be valid before you add it.
The user numbers identify users in reports
transmitted from your system. Additionally, you
will be able to change the following:
Enter the new passcode again.
•
As soon as a number is pressed, Entering:
appears on the third line next to the
asterisks.
•
•
•
•
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all six passcode
digits are entered.
8. If the passcode matches the previously
entered passcode, the display changes to
Passcode changed.
If the passcode does not match, the
command center will emit a error tone and
display Passcode not changed.
Contact your security company if you don’t know
what user numbers, authority levels, or areas are
available. See the Appendix for further
information on adding passcodes.
Before you begin, keep these points in mind:
•
•
•
9. The display automatically returns to idle text
after three seconds.
•
Bosch Security Systems | 12/15 | F01U036089-04
the authority level (which determines what
system functions the passcode can access)
the area number (which identifies which
parts of your security system the user will
have access to)
the name of the user
the card number they use for access control
whether they are a Master or Sub-User.
Do not try to add new users without knowing
the available user numbers. An already
defined user number will be overwritten
when the new user is defined. These are two
or three digit numbers, not to be confused
with passcodes, that identify users at your
security company.
When choosing passcodes, choose a new
passcode three to six digits long. If you
choose a passcode with the same digit in
consecutive order (for example “33” in
334697), take care when entering it.
To avoid conflicting with other passcodes and
duress codes, your system does not let you
change passcodes that are the same within
plus or minus 2 of an existing passcode. For
example, if 1234 were an existing code, your
system would not let you add or change your
code to 1232, 1233, 1234, 1235, or 1236.
Choose an authority level for each area. Not
assigning the authority level for an area
denies the passcode access to that area.
57
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5
+ 6)
1. Ensure your keypad shows idle disarmed
text.
6. The display changes to show the user number
entered and the user’s name (if any).
(User 2 is used as an example.)
Press the Continue> soft key to proceed on
to changing the user’s information.
2. Press the COMMAND key. The display shows
*System Command*.
If there is no name for the user, the text
USER 2 appears in the second line.
(User 2 is used as an example.)
3. Press the 5 key and then the 6 key.
Press the Continue> soft key to change the
user’s information.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the ADD/CHG USER
?> prompt, press its adjacent soft
key.
4. The display changes to show Add / Change
User Enter user #:
5. Enter the user number and press either the
Enter> soft key or the ENTER button.
58
7. The display changes to Add/Change Menu.
The display varies depending on the type of
control panel that was installed in your
system.

My system has a D9412 or D7412
Control Panel

My system has a D9112 or D7212
Control Panel
If your system has a D9412 or D7412 Control
Panel, this menu allows the following User
items to be changed:
• Passcode - Press the <Passcode soft key
to change the user’s passcode.
• Level - Press the <Level soft key to
change the user’s Authority Level.
• Name - Press the Name> soft key to
change the user’s name.
• Card - Press the Card> soft key to change
the user’s card.
• Sub-User - Press the Sub-User> soft key
to change the user’s sub-user status.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)
If your system has a D9112 or D7212 Control
Panel, this menu allows the following User
items to be changed:
• Name - Press the Name> soft key to
change the user’s name.
• Passcode - Press the <Passcode soft key
to change the user’s passcode.
• Level - Press the <Level soft key to
change the user’s Authority Level.
3. The display changes to Enter new passcode:
Enter the new passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the
asterisks.
Add/Change Passcode
1. Pressing the <Passcode or the Passcode>
soft key will allow you to add/change a user’s
passcode.
User 123 is used here as an example.
2. The display changes to User 123 Add a
passcode for this user?
Press the Yes> soft key to add a new
passcode.
Go to Step 3.
Pressing the No> soft key advances to
Add/Change Level, if the panel is a D9112 or
D7212, or Add/Change Card, if the panel is a
D9412 or D7412.
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all passcode digits
are entered.
Press the ENTER button.
If the passcode matches the previously enter
passcode, the display changes to Passcode
added.
Pressing the Next> soft key advances to the
Add/Change Level (if the panel is a D9112 or
D7212) or Add/Change Card (if the panel is a
D9412 or D7412).
If an invalid passcode is entered, the
command center will momentarily display
Passcode is already in use. Please try again.
If the user already has an assigned passcode.
it will be detected by the panel and will
automatically go to Step 4.
If the passcode does not match, the
command center will emit an error tone and
display Passcode not changed.
Pressing the Next> soft key advances to the
Add/Change Level (if the panel is a D9112 or
D7212) or Add/Change Card (if the panel is a
D9412 or D7412).
Bosch Security Systems | 12/15 | F01U036089-04
59
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5
+ 6)
4. The display changes to User 123 Change this
user’s passcode?
Press the Yes> soft key to change the
passcode.
Press the No> soft key not to change the
passcode and skip ahead to Add/Change
Level (if the panel type is a D9112 or D7212)
otherwise if the panel is a D9412 or D7412,
the Add/Change Card appears next.
If the passcode matches the previously enter
passcode, the display changes to Passcode
changed.
If the passcode does not match, the
command center will emit an error tone and
display Passcode not changed.
You will prompted for the user’s passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the
asterisks.
It will appear on the display as asterisks (*).
5. Press the <Exit soft key to return to the
Add/Change Menu.
Add/Change Level
1. Pressing the <Level or the Level> soft key will
allow you to add/change a user’s authority
level.
2. The display changes to User 123 Add Auth.
Level for this user?
Press the ENTER button.
The display changes to Enter new passcode
again:
Press the Yes> soft key to add an Authority
Level.
Enter the new passcode again.
Press the ENTER button.
If an invalid passcode is entered, the
command center will momentarily display
Passcode is already in use. Please try again.
60
Press the No> soft key to advance to
Add/Change Passcode - if the panel is a
D9112 or a D7212) or to Change Sub-User ID
- if the panel is a D9412 or a D7412.
Press the <Exit soft key to exit out of this
menu and return to the Level changed.
display (Refer Step 7).
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)
3. The display changes to Is this user
authorized in Area 1?
Press the No> soft key to advance to
Add/Change Passcode (if the panel is a
D9112 or a D7212) or to Change Sub-User ID
(if the panel is a D9412 or a D7412).
Press the <Exit soft key to exit out of this
menu and return to the Level changed.
display (refer to Step 7).
Press the Yes> soft key to/add change this
user’s authority level in Area 1.
Press the No> soft key if the user isn’t
authorized in Area 1 and proceed to display
user’s authorization in Area 2.
If the user is authorized in Area 1, the
displays changes to User’s current authority
level: 14 for Area 1.
(14 is used as an example here)
Press the <Exit soft key to exit out of this
menu and return to the Level changed
display.
If the user is authorized in Area 1, the
displays changes to User’s current authority
level: 14 for Area 1.
(14 is used as an example here)
To change the Authority Level, Enter a new
authority level (from 1 to 14), if desired, and
press either the Enter> soft key or the ENTER
button.
Before determining the Authority Level for a
user, please consult your security company to
assist you in selecting the correct authority
level.
To change the Authority Level, Enter a new
authority level (from 1 to 14), if desired, and
press either the Enter> soft key or the ENTER
button.
Before determining the Authority Level for a
user, please consult your security company to
assist you in selecting the correct authority
level.
Press the <Exit soft key to exit out of this
menu and return to the Level changed
display.
Press the <Exit soft key to exit out of this
menu and return to the Level changed.
display.
6. Repeat Step 5 for each area through Area 8.
7. Once the user’s authority level has been
verified for Area 8, the display changes to
Level changed.
If the Next> soft key is pressed, the display
changes to Add/Change Sub-User ID (for
D9412/D7412 panels) or Add/Change
Passcode (for D9112/D7212 panels).
4. Repeat Step 3 for each area through Area 8.
5. The display changes to User 123 Change this
user’s Auth. Level?
Press the Yes> soft key to add/change this
user’s authority level in Area 1.
Bosch Security Systems | 12/15 | F01U036089-04
61
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5
+ 6)
If the <Exit soft key is pressed, the display
changes to Add / Change User Enter User #:
3. Once the name appears as desired, press the
Continue> soft key.
4. The display will change to New user name is
JANE DOE Is this correct?
At this point you can accept or reject the
changes.
Adding/Changing a User’s Name
1. Pressing the Name> soft key will change the
display to <? JANE DOE
(JANE DOE is used as an example.)
Press the Yes> soft key to accept the name
and return to the main Add/Change Menu
(depending on panel model).
D9412/D7412:
2. To change the name use the following soft
keys:
Pressing this soft key will display a series of
help screens where the keypad can be used
to enter specific letters.
Pressing either of these soft keys will cause
the currently underlined character to change
the previous or next character in the list. The
available characters are A-Z, 0-9, @, #, $, &, *,
/, -, _, ?, and +.
Pressing either of these soft keys will cause
the cursor of the currently underlined
character to move left to the previous
position in the name or right to the next
position in the name.
Another option is to use the numeric keys to
add characters to the text. For the keys with
letters, pressing the digit will allow you to
cycle through the letters on the key. For
instance, pressing '2' will display an A.
Pressing it again will display a B, and
pressing it a third time will display a C.
The '0' (zero) key will display a 0. The '1' key
functions like a space bar - it puts a space in
the current position, and advances to the
next position.
62
D9112/D7212:
Press the <No soft key to reject the name and
return to Step 1.
Add/Change Card
1. Pressing the Card> soft key will allow you to
add/change a user’s access card or
credential.
2. The display changes to either one of the
following depending on if an access card
exists for the user:
User 123 Add Access Card for this user? - if
no access card exists for that user.
Pressing the Yes> soft key will jump to Step
3.
Pressing the No> soft key will jump to
Add/Change Level.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)
User 123 Change this user’s Access Card? if an access card already exists for this user
and you wish to change it. (In both cases,
123 is used as an example)
Then the display returns to Present card to
card reader now.
Pressing the <Exit soft key exits out of this
function and returns the display to idle text.
Pressing the Yes> soft key will jump to Step
3.
Pressing the No> soft key will jump to
Add/Change Level.
5. If the card is accepted, the display changes
to either Card added. or Card changed if the
card already exists in your system.
3. If a card reader is connected to your system,
the display changes to Present card to card
reader now.
Pressing the <Exit soft key exits out of this
function and returns the display to idle text.
If the display changes to D9210 not ready,
contact your security company.
Pressing the <Exit soft key exits out of this
function and returns the display to idle text.
Pressing the Next> soft key exits out of this
function and returns the display to either
Add/Change Level.
Pressing the <Exit soft key exits out of this
function and returns the display to idle text.
4. If the card you are trying to add to the system
already exists, an error tone sounds and the
display changes to Card already exists.
Please try again.
Pressing the <Exit soft key exits out of this
function and returns the display to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
63
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5
+ 6)
Add/Change Sub-User ID
For each user in the system, there can be up to
four access cards; one Master User (assigned in
the Card> prompt) and up to three sub-users.
4. If adding or changing a sub-user and a card
reader is connected to your system, the
display changes to Add (or Change) Sub-User
1: Present card to card reader now.
1. Pressing the Sub-User> soft key will allow
you to add/change a user’s Sub-User access
card or credential.
2. The display changes to User 123 Add/Change
Sub-User IDs? to add or change any of this
user’s sub-user IDs.
If the display changes to D9210 not ready,
contact your security company.
Pressing the Yes> soft key will jump to Step
3.
Pressing the No> soft key will jump to
Add/Change Passcode.
3. The display changes to Select Sub-User:
Press the <Sub-User 1 soft key to add or
change sub-user 1.
Press the <Sub-User 2 soft key to add or
change sub-user 2.
5. If 20 seconds elapse without pressing a key
the display returns to idle text. Pressing the
<Exit soft key exits out of this function and
returns the display to the main Add / Change
User display.
6. If the card you are trying to add to the system
already exists, an error tone sounds and the
display changes to Card already exists.
Please try again.
Press the <Sub-User 3 soft key to add or
change sub-user 3.
Press the Exit> soft key to return to the main
Add / Change User display.
If 20 seconds elapse without pressing a key
returns the display to idle text. Pressing the
<Exit soft key exits out of this function and
returns the display to the main Add / Change
User display.
64
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DEFAULT TEXT ? (COMMAND + 5 + 7)
Then the display returns to Present card to
card reader now.
DEFAULT TEXT ? (COMMAND + 5 + 7)
This function allows the current state of the area
for 3 seconds before returning to idle text.
1. Ensure your keypad shows idle disarmed
text.
Present the card to the reader to continue or
press the <Exit soft key to exit out of this
function and return the display to idle text.
7. If the card is accepted, the display changes
to either Card added. or Card changed if the
card already exists in your system.
2. Press the COMMAND key. The display shows
*System Command*.
3. Press the 5 key and then the 7 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Pressing the <Exit soft key exits out of this
function and returns the display to the main
Add / Change User display.
Pressing the Next> soft key exits out of this
function and returns the display to
Add/Change Passcode depending on if a
passcode already exists for the user.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the DEFAULT TEXT
?> prompt, press its adjacent soft
key.
4. The current state of the area is displayed for
3 seconds before returning to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
65
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - FIRE TEST ? (COMMAND + 5 + 8)
FIRE TEST ? (COMMAND + 5 + 8)
Use this function to test fire points and other 24hour points to be certain they function properly.
You can review both the tested and untested
points at your command center to help pinpoint
any problems.
Upon initiation, the fire test will test the fire bell
pattern on the bell output and ring the command
center fire bell for 2 seconds. The AC will be
disabled for 4 minutes in order to test the
system’s battery power. If the battery cannot
maintain the system for the 4-minute period, the
command center will appear to go dead. If this
happens, contact your security company. At the
end of the 4-minute period, AC is returned to the
system and the panel restores. A message will be
sent to your security company upon initiation and
completion of the Fire Test. During the Fire
Test, no 24-hour alarms will be sent to your
security company.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the FIRE TEST ?>
prompt, press its adjacent soft key.
4. When the display shows ### points remain to
be tested you can begin. (### is the number
of points).
Test each point by first activating the
detection device to fault the point.
If there is no activity on the system for 20
minutes, the system will automatically exit from
the Fire Test.
Using Fire Test:
1. Ensure your keypad shows idle disarmed
text.
2. Press the COMMAND key. The display shows
*System Command*.
If you know the point number, you
can enter it by pressing its number
key and then the ENTER key.
The display will change to show the
point that was entered. If the point
is invalid the message “Invalid Point”
or “This is not a valid walk point”
appears.
3. Press the 5 key and then the 8 key.
66
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - FIRE TEST ? (COMMAND + 5 + 8)
5. As you fault each point, your command center
will display the point text for 60 seconds and
ring the fire sounders for 2 seconds. This
verifies that the detection device is working
properly. Your system automatically resets
smoke detectors.
•
•
When a resettable point (such as a smoke
detector) is faulted, the display shows
Sensors…resetting…please wait… for 5
seconds. During this time power is
removed from smoke power relays.
Faulting a point more than once does not
increment the test count. However, the
command center emits a brief tone and
displays the point text each time you fault
the point allowing you to test multiple
devices assigned to one point.
6. When the point has been tested, the display
changes to show SMOKE DETECTOR tested.
Press the Point information> soft key to see
information about specific points that have
not yet been tested.
The display changes to show the information
for that point.
Move through this list by pressing the Next
Point> soft key.
Press the <Exit soft key to return to the ###
points remain to be tested. before continuing
the Fire Test.
8. When all 24-hour points have been tested, 0
points remain to be tested is displayed.
Press the <Exit soft key.
The display momentarily shows All points
have been tested.
7. During the Fire Test you may want to see the
points that remain untested by pressing the
View untested pts> soft key.
before returning to idle text.
The display shows ### pts untested.
Bosch Security Systems | 12/15 | F01U036089-04
67
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DISPLAY REV ? (COMMAND + 5 + 9)
DISPLAY REV ? (COMMAND + 5 + 9)
1. Ensure your keypad shows idle disarmed
text.
5. The display will return to idle text after 5
seconds.
SERVICE MENU ? (9 + 9 + Enter)
2. Press the COMMAND key. The display shows
*System Command*.
The service menu is used to access the following
commands:
•
3. Press the 5 key and then the 9 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
•
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
•
When you reach the DISPLAY REV ?>
prompt, press its adjacent soft key.
•
4. The display will change to Radionics D9412*
Version 6-40
(D9412 and 6-40 are used as an example,
other panels could be D9112, D7412, D7212)
•
68
View Log - Use this function to review events
in your system at your command center.
Reviewing past events may help you identify
problems. Viewing events does not require
any additional equipment since the
information is displayed at your command
center. Events are stored in the panel’s
memory in order of occurrence and tagged
with the date and time.
Print Log - The Print Log function lets you
print the events stored in your security
system’s log. You can choose to print the
entire log or set a start date and print the
events recorded from that date up to today.
Your system must include a parallel printer
interface and a printer to perform this
function.
Display Rev (COMMAND + 5 + 9) - The
command will retrieve the panel’s software
version and display it.
Service Walk (D9412/D9112 only) – The
command will allow all the points on the
system to be walk tested regardless of the
type of point. For D7412 and D7212 panels
this function must be added to the keypad’s
menu. Contact your security company for
more information.
Default Text – This command will show the
current state of the area for 3 seconds before
returning to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)
1. Ensure your keypad shows idle disarmed
text.
3. Enter the start date in the form of mm/dd.
For example, to enter 7/14 as the start date,
press 0 + 7 + 1 + 4
Once you start entering digits, the Go to last
event> soft key is replaced with the Enter>
soft key.
2. Press the 9 key twice.
3. Press the ENTER key.
4. The display changes to show the service
menu.
Press the <Exit soft key to exit this function
and return to idle text.
4. Press either the Enter> soft key or the ENTER
button.
Service Walk Test?> appears on D9412/D9112
Panels only
Using View Log
1. Press the View Log ?> soft key.
5. If the date entered is valid, the first event for
that date will appear.
Press the <Exit soft key to exit this function
and return to idle text.
If the date entered is invalid (there are no
events with that date in the log), it will
display the next latest event in the log.
2. The display changes to Enter start date:
Press the Go to last event> soft key to go to
the last event in the log.
Press the <Exit soft key to exit this function
and return to idle text.
Press the <Exit soft key to exit this function
and return to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
69
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)
6. The display will show one of two ways
depending on if the date entered was for an
event first in the log or not.
• If the date was for the first event in the
log, it will display the next latest event in
the log.
•
If the date was for an event (not the first)
in the log, the display will be the same
except the <Previous soft key has been
added.
Using Print Log
1. Press the Print Log ?> soft key.
2. The display changes to Enter start date:
Press the Print all events> soft key to print all
events in the log.
Press the <Exit soft key to exit this function
and return to idle text.
The events are sent to a connected printer
and display changes to Printing all events in
history for three seconds before returning to
idle text.
Press the <Exit soft key to exit this function
and return to idle text.
7. Press the Next> soft key to go to the next
event in the log.
If there are no more events in the log, *End of
Log* will appear.
3. Enter the start date in the form of mm/dd.
For example, to enter 12/21 as the start date,
press 1 + 2 + 2 + 1.
Press the <Previous soft key to go to the
previous event in the log.
Press the <Exit soft key to exit this function
and return to idle text.
Once you start entering digits, the Print all
events> soft key is replaced with the Enter>
soft key.
Press either the Enter> soft key or the ENTER
button.
70
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)
4. If the date entered is valid, the events for
that date will be sent to a connected printer
and the display will show Printing events. for
three seconds, before returning to idle text.
Using Service Walk Test
The Service Walk Test function is
only available in the Service Menu for
D9412 and D9112 panels. If the
panel model is D7412 or D7212, the
Service Walk Test will have to be
enabled on the Function list for the
command center through the panel’s
programming.
1. When the display shows ### points remain to
be tested you can begin. (### is the number
of points).
Using Display Rev
1. Press the Display Rev ?> soft key.
2. The display will change to *Bosch D9412*
Version 6-40
(D9412 and 6-40 are used as an example,
other panels could be D9112, D7412,
D7212).
3. The display will return to idle text after 5
seconds.
If you know the point number, you
can enter it by pressing its number
key and then the ENTER key.
The display will change to show the
point that was entered. If the point
is invalid the message “Invalid Point”
or “This is not a valid walk point”
appears.
Test each point by first opening and then
closing the door or window or other
detection device.
Check the display after testing each point.
For interior points, walking past the device
once is sufficient. If any point does not test
correctly, contact your security company for
service.
Bosch Security Systems | 12/15 | F01U036089-04
71
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)
2. During the Walk Test you may want to see the
points that remain untested by pressing the
View untested pts> soft key.
3. When all points have been tested, 0 points
remain to be tested is displayed.
The display shows ### pts untested.
Press the <Exit soft key.
The display momentarily shows All points
have been tested.
Press the Point information> soft key to see
information about specific points that have
not yet been tested.
The display changes to show the information
for that point.
Move through this list by pressing the Next
Point> soft key.
Press the <Exit soft key to return to the ###
points remain to be tested. before continuing
the Service Walk Test.
before returning to idle text.
Using Default Text
This function allows the current state of the area
for 3 seconds before returning to idle text.
1. Press the Default Text?> soft key to display
the current state of the area.
2. The current state of the area is displayed for
3 seconds before returning to idle text.
72
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)
Using Setup
The Setup function is accessed by pressing the
Setup? > soft key.
The adjustable functions that are available in this
menu are:
•
High Brightness,
•
Low Brightness,
•
Contrast.
Each of these selections have <- Level +> soft
keys on either side of the display that allows you
to increase (+) or decrease (-) the setting being
displayed. The High and Low Brightness are
associated to Command 49’s Bright Display and
Dim Display settings.
Also shown in this menu is the Command Center
address, whether the Encoding Tone is On or Off,
and the Command Center software revision.
Bosch Security Systems | 12/15 | F01U036089-04
73
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Working with Multiple Areas from a Single
Command Center
Part IV: Multi-Area Use
Working with Multiple Areas from a
Single Command Center
Each of the functions described in the preceding
section on Advanced Commands is presented as
though your system includes only one area. If
your system includes more than one area, it can
be set up in one of two ways by the installing
company:
•
•
Each command center will only have access
to the local area to which it is assigned, or
Each command center may access either
some or all areas beyond the one to which it
is assigned. This factor is referred to
hereafter as command center scope.
If your command center allows access to areas
other than the local area (that is to say, has
scope in other areas), then the command center
will limit your access to those areas within the
command center scope and for which your
personal passcode has authority.
Given that you have access to areas beyond the
local area, the means of accessing the various
system functions depends upon the specific
function.
For some functions, the command center allows
you to select the area (or point) in which to
perform the function. These “selectable”
functions are:
•
•
•
•
•
•
•
FIRE TEST?,
VIEW POINT STATUS? and
VIEW AREA STATUS?
Some functions may be area-specific. To perform
these functions, you must first use the MOVE TO
AREA ? function (Command 50) to gain access to
the desired area. Once in the desired area you
can perform the functions you wish. Area-specific
functions include:
•
•
•
•
•
•
•
•
PERIMETR INST? (Perimeter On Instant),
PERIMETR DELAY ? (Perimeter On Delay),
PERIMETR PART ? (Perimeter On Partial),
EXTEND CLOSING ?,
WATCH MODE ?,
COMMAND 7 ?,
COMMAND 9 ? and
CHG DISPLAY ?.
A last group of functions don’t relate to specific
areas and are thus system-wide. These are:
•
•
•
•
•
•
•
•
•
SEND REPORT?,
REMOTE PROG ?,
CHG TIME/DATE ?,
CHG SKEDS ?,
DEL PASSCODES ?,
CHG RELAYS ?,
CHG PASSCODES ?,
PRINT LOG ? and
VIEW LOG?
DISARM ?,
MASTER ARM AREA ?.
BYPASS A POINT? and
UNBYPASS A POINT?
Another group of functions may automatically
work in all areas in which you have passcode
authority and which are within the scope of the
command center. These are:
•
•
•
•
•
•
•
•
74
Turning On Multiple Areas with a Passcode,
Turning Off Multiple Areas with a Passcode,
DISARM ALL ?,
MASTER ARM ALL?,
VIEW MEMORY?,
WALK TEST?,
RESET SENSORS ?,
ADD PASSCODES ?,
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - View Area Status
View Area Status
View Point Status
Use this function when you need to know the
status (whether armed or disarmed) of areas
other than the one you’re in.
Use this function to identify the number or
location of each point in an area, and to show the
current condition of any point you select.
1. Ensure your keypad shows idle disarmed
text.
1. Ensure your keypad shows idle disarmed
text.
2. Press the Menu> key to enter the Command
Menu.
2. Press the Menu> key to enter the Command
Menu.
3. Press Next> repeatedly until you reach the
VIEW AREA STAT ?> prompt.
3. Press Next> repeatedly until you reach the
VIEW PT STATUS ?> prompt.
Press the adjacent soft key.
4. The display will change to show on the top
line the area name and the current status on
the second line.
Pressing the Next> soft key will change the
display to the next area and remain for 20
seconds or until the Next> soft key is pressed
for the next area. If the time has elapsed, the
display returns to idle text.
Pressing the <Previous soft key will change
the display to the previous area.
5. Press the <Exit soft key to return to idle text.
Press the adjacent soft key.
4. In this example, Area 1 is the area and there
are eight points assigned to area 1 that can
be viewed.
Press the Next> soft key to view the first
point in the area; press the <Previous soft
key to view the last point in the area. You
may press the <Exit soft key at any time to
exit this function.
5. The top line indicates that you are still in
View Point Status mode. The second line will
display the point text.
Pressing the Next> soft key takes you to the
next point in the area whereas the <Previous
soft key will take you to the previous point in
the area.
To view the status of a point, press the
Status> soft key.
Bosch Security Systems | 12/15 | F01U036089-04
75
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - MOVE TO AREA ? (COMMAND + 5 + 0)
6. After pressing the Status> key, the command
center will display the following information:
Refer to Table 5 for more information.
1. Ensure your keypad shows idle disarmed
text.
2. Press the COMMAND key. The display shows
*System Command*.
Table 5: Screen Area Definitions
Line
#
Area
Name
Definition
1
Area #
This may display numbers 1 to
8.
2
Pt #
This may display point numbers
1 to 127 and 129 to 247,
(Point
State), HW
Normal
indicates that the
point is not in the
faulted state.
Open
indicates that the
point is in an open
state.
Short
indicates that the
point is in a shorted
state.
Missing
indicates that the
point is missing.
MOVE TO AREA ? (COMMAND + 5 + 0)
With this function you can perform tasks in an
area other than the one you’re in without having
to physically go to that area. Your access to other
areas is limited by the scope of the command
center and your authority level. For example, if
your passcode gives you authority to all 8 areas,
but the command center you’re working with is
limited in scope to areas 1 and 2, then you will
only be able to move to either area 1 or area 2.
Upon moving to another area, the range of tasks
you may perform depends upon the command
center you’re working with. Once you’ve
performed a task (such as Turning the Area On),
the command center reverts back to its
programmed area after 10 seconds. Thus only
one task can be performed in another area at a
time.
76
3. Press the 5 key and then the 0 key.
If you prefer, you may use the
Command Menu in place of steps 2
and 3 to initiate this function.
Press the MENU> soft key to enter
the Command Menu.
Press NEXT> soft key repeatedly.
When you reach the MOVE TO AREA
?> prompt, press its adjacent soft
key.
4. You may be prompted for your passcode. If
so, enter your passcode and press the ENTER
key. It will appear on the display as asterisks
(*).
The <Exit soft key will quit this function and
return to idle text.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning On the System
5. The command center will then display the
Area Name Text of each area that falls within
the scope of the command center and
authority level of the user, if applicable. (All 8
area names are shown as an example).
If the user's authority level does not
permit access to a certain area and
that area is not within the scope of
the command center, or the area is
not enabled, it will not appear in the
display.
If the area you wish to move to does not
appear in this list, press the Next> key to
display additional areas.
7. You are now able to perform tasks in this
area. The number of areas to which you can
move will be limited by the scope of the
command center.
If you try to move to an area for which the
command center does not have scope, *NO
AUTHORITY* is displayed.
8. When you have completed all tasks in the
area you’ve moved to, simply allow the
command center to time-out and revert to
the area from which you started or enter the
Move to Area function again.
Turning On the System
Turning on Selected Areas
Areas covered in the scope of the command
center can be armed individually by accessing the
Master Arm function through the menu.
1. Press the Menu> key to enter the Command
Menu.
To select an area, simply press the soft key
corresponding to the Area Name.
6. Moving to…AREA 1 WAREHOUSE displays
briefly, and then the text of the area you’ve
moved to is displayed (AREA 1 WAREHOUSE
is used as an example here).
Bosch Security Systems | 12/15 | F01U036089-04
2. Press the Next> soft key repeatedly until you
reach the MASTER ARM ?> prompt then
press the adjacent soft key.
3. You will prompted for your passcode. It will
appear on the display as asterisks (*).
77
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning On the System
4. The display changes and shows MASTER ARM
ALL ? with the following options:
• <Previous soft key – will scroll to the last
area that can be armed (based on
passcode and authority level)
• Next> soft key – will scroll to the first
area that can be armed (based on
passcode and authority level)
• Arm> soft key – will arm all areas (based
on passcode and authority level)
• <Exit soft key – will return the display to
idle text
5. If the Next> soft key is pressed, the first area
that can be armed (based on passcode
entered and user authority level) is displayed
(AREA 1 WAREHOUSE is used an example of
the first area that can be armed).
1. Enter your passcode and press ENTER.
2. The command center will display the
following:
Command center scope and/or your authority
level limit the actual number of areas you may
turn on. For example, if you have authority to
arm all 8 areas but the scope of the
command center you’re using is limited to
areas 1, 2, and 5, then you will only be able
to turn on areas 1, 2, and 5.
3. If a point is faulted (door or window open for
example), see Turning On the System (Arming)
With Doors or Windows Open for further
information.
Faulted Points in Other Areas
6. Pressing the Arm> soft key will cause AREA 1
WAREHOUSE is now arming… to display for 3
seconds before the prompt to arm the next
available area is displayed.
If there is a faulted point in an area you select
(other than the one you are in), Check Area 1 (1
is used as an example here) appears for 3
seconds and then the display returns to the area
disarmed idle text.
If there is a faulted point in more than one area
and the system is being armed, the display will
prompt Check Area 1 3 meaning there are
faulted points in Areas 1 and 3.
Turning on Multiple Areas with a Passcode
You can use your personal passcode to turn on
both perimeter and interior points in all areas
where your passcode has authority. If there are
areas already turned on, this function turns on all
areas that are off without changing the status of
the areas that are already on.
78
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turn On the Entire System Without Delays
Try one of the following:
•
Clear faulted points (close doors and/or
windows) and return to step 1.
•
Bypass faulted points (if your system and/or
authority allows) and return to step 1.
•
Force arm (if your system and/or authority
allows). See Turning On the System (Arming)
With Doors or Windows Open for more
information.
Turn On the Entire System Without
Delays
You can use this Command Menu function to turn
on the entire system, both perimeter and interior,
without delays. You may use this function in all of
the areas or some of the areas where your
passcode has authority. If there are areas already
turned on, this function turns on all areas that
are off without changing the status of the areas
that are already on.
Turning on All or Selected Areas
4. The display changes and shows MASTER ARM
ALL ? with the following options:
• <Previous soft key – will scroll to the last
area that can be armed (based on
passcode and authority level)
• Next> soft key – will scroll to the first
area that can be armed (based on
passcode and authority level)
• Arm> soft key – will arm all areas (based
on passcode and authority level)
• <Exit soft key – will return the display to
idle text
5. If the Next> soft key is pressed, the first area
that can be armed (based on passcode
entered and user authority level) is displayed
(AREA 1 WAREHOUSE is used an example of
the first area that can be armed).
Areas covered in the scope of the command
center can be armed individually by accessing the
Master Arm function through the menu.
1. Press the Menu> key to enter the Command
Menu.
2. Press the Next> soft key repeatedly until you
reach the MASTER ARM INST ?> prompt then
press the adjacent soft key.
6. Pressing the Arm> soft key will cause AREA 1
WAREHOUSE is now arming… to display for 3
seconds before the prompt to arm the next
available area is displayed.
3. You will prompted for your passcode. It will
appear on the display as asterisks (*).
7. Once all available areas have been displayed,
the display returns to ARM INSTANT ALL ?
Bosch Security Systems | 12/15 | F01U036089-04
79
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning Off the System
8. To instantly arm all the areas that are within
the scope of the command center, press the
Arm> soft key.
Turning Off Multiple Areas with Disarm All
•
9. This display changes to show AREA 1
WAREHOUSE All On Instant indicating that
the all areas are armed.
•
Turning Off the System
Turning Off Multiple Areas with a Passcode
This function is useful for turning off multiple
areas with a few keystrokes. It is quicker than
disarming several areas independently. Your
passcode must have the proper authority level for
each area.
•
•
•
80
After enter your passcode, the following will
display Disarm: 12345678 All userauthorized areas are now disarmed. (Not all
area number may appear due to what areas
are in the scope of the command center.
•
This function turns off multiple areas with a
few keystrokes. It is quicker than disarming
several areas independently. Your passcode
must have the proper authority level for each
area. This function works the same as
entering your passcode to disarm, but allows
the Disarm All feature to be included in the
Command Menu.
When an area is turned on (armed), you must
enter a door programmed for entry delay
time. Opening the door, starts the entry delay
time. Failing to turn off the system before the
entry delay time expires or entering through a
door not programmed for entry delay time,
causes an alarm.
If this happens, silence the alarm by entering
your personal passcode and pressing ENTER.
Call your security company to let them know
that it is not an emergency situation.
1. The display initially shows that the system is
armed.
2. Press the Menu> key to enter the Command
Menu.
When an area is turned on (armed), you must
enter a door programmed for entry delay
time. Opening the door, starts the entry delay
time. Failing to turn off the system before the
entry delay time expires or entering through a
door not programmed for entry delay time,
causes an alarm.
If this happens, silence the alarm by entering
your personal passcode and pressing ENTER.
Call your security company to let them know
that it is not an emergency situation.
3. Press the Next> soft key repeatedly until you
reach the DISARM ?> prompt then press the
adjacent soft key.
4. If entering through a door which is part of an
area that is armed, the display changes to
show:
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning Off the System
5. Enter your passcode and press ENTER.
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all the passcode
digits are entered.
6. If the entered passcode is valid, the display
changes to show DISARM ALL?
Press the Disarm> soft key to disarm all
armed areas.
Turning Off Selected Areas
If your passcode has the proper authority level
this function allows you to turn off areas other
than the one you are in.
1. The display initially shows that the system is
armed.
2. Press the Menu> key to enter the Command
Menu.
3. Press the Next> soft key repeatedly until you
reach the DISARM ?> prompt then press the
adjacent soft key.
Press the Next> soft key to go to the first
armed area (see Turning Off Selected Areas).
Press the <Previous soft key to go to the last
armed area.
Press the <Exit soft key to return to idle text.
7. If the Disarm> soft key is pressed to disarm
all areas, the display changes to show
Disarm: 12345678 All user-authorized areas
are now disarmed. indicating that all areas
are being turned off. Command center scope
and/or your authority level limit the actual
number of areas you may turn off.
4. If entering through a door which is part of an
area that is armed, the display changes to
show:
5. Enter your passcode and press ENTER.
The passcode is shown as asterisks (*) when
entered and advance from the right side of
the display to the left until all the passcode
digits are entered.
For example, if you have authority to disarm
all 8 areas but the scope of the command
center you’re using is limited to areas 1, 2,
and 5, then you will only be able to turn off
areas 1, 2, and 5.
Bosch Security Systems | 12/15 | F01U036089-04
81
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning Off the System
6. If the entered passcode is valid, the display
changes to show DISARM ALL?
Press the Disarm> soft key to disarm all
armed areas.
7. Press the Next> soft key to go to the first
armed area.
8. The display changes to show DISARM AREA 1
? (or the first area that is armed).
Press the Disarm> soft key to disarm this
area.
Press the Next> soft key to scroll through the
remaining areas you have the authority to
turn off.
To disarm the area, press the Disarm> soft
key.
9. After turning off other areas, the command
center’s display returns to the idle text for
the area you are in.
82
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Supplementary Information for Adding Passcodes
If you are having trouble understanding the
concept of authority levels, try this simple
exercise. Refer to the column titled E/P on the
next page. Notice that your security technician
has marked some of the cells in this column with
the letter “E”, others the letter “P”, while others
are left blank. An “E” indicates that this function
is enabled for all authority levels. A “P” indicates
that the function is passcode protected. Look
across the same row, and notice that some of the
cells in the authority level area have the letter
“E”. For each authority level in which an “E”
appears, this function is enabled (with a
passcode required). A blank cell in the E/P
column means that this function is unavailable
for any authority level.
Appendix
Supplementary Information for Adding
Passcodes
Use the information contained in this
Supplement to help you add user passcodes.
User Authority Levels
Your security company uses the information
contained on this page to establish authority
levels for system users. For each of the 1- 14
authority levels, each command center function is
either enabled (E), disabled (blank), or Passcode
enabled (P). A function that is enabled (E) is
available to all users. A function that is passcode
enabled (P) is only available to users assigned an
authority level that includes that function. If you
do not want a particular command included in a
given authority level, leave it blank.
Under the heading Authority Level, you’ll see
columns 1-14, representing the fourteen
authority levels. Now look at the column labeled
1. Following down this column, you’ll see that
some cells are blank while some contain the
letter “E”, which stands for enabled. Wherever
there is an “E”, it means that that function is
available to users with an authority level of 1.
Passcode Worksheet
The passcode worksheet presents the information discussed previously onto one page, and also
includes the user’s ID number, assigned passcode, and his or her name.
An important piece of information included in the passcode worksheet is the listing of areas to which
the user has access, along with the authority level assignment for each of those areas.
User Interface
Authority Levels
#
Functions*
1
2
3
4
5
6
7
8
9
10
11
12
13
Disarm ?
Master Arm Delay ?
Master Arm Instant?
Perimeter Instant ?
Perimeter Delay ?
Watch Mode ?
Perimeter Part ?
View Area Status ?
View Memory ?
View Pt Status ?
Walk Test ?
Fire Test ?
Send Report ?
14
♦Door Control ?
♦Cycle Door ?
Command
CMD 1
CMD 11
CMD 2
CMD 3
CMD 6
CMD 8
CMD 40
CMD 44
CMD 58
CMD
41/42
CMD 46
E/P
1
2
3
4
5
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
P
P
E
P
P
E
E
E
P
P
P
E
Bosch Security Systems | 12/15 | F01U036089-04
6
7
8
9
10
11
12
13
14
E
E
E
83
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
Authority Levels
37
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
33
34
35
♦Unlock Door ?
♦Secure Door ?
♦Access Control
Level?
Change Display ?
Change Time/Date ?
Change Passcode ?
Add User ?
Del User ?
Extend Close ?
View Log ?
Print Log ?
User Command 7 ?
User Command 9 ?
Bypass a Point ?
Unbypass a Point ?
Reset Sensors ?
Change Relays ?
Remote Program ?
Move To Area ?
Display Rev ?
Service Walk ?
Default Text ?
Change Skeds ?
CMD 49
CMD 45
CMD 55
CMD 56
CMD 53
CMD 51
CMD 7
CMD 9
CMD 0
CMD 00
CMD 47
CMD 54
CMD 43
CMD 50
CMD 59
CMD 57
CMD 52
E
E
P
E
E
E
E
E
P
P
P
P
E
P
P
P
P
P
E
P
P
P
E
P
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
* Command Center Function Authority Level Options: Blank = Disabled, E = Enabled.
♦ D9412x/D7412x only.
Authority Level 15 can not be edited.
84
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User Interface
Authority Levels
#
Functions*
#
Custom Functions
Command
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Custom Function 128
Custom Function 129
Custom Function 130
Custom Function 131
Custom Function 132
Custom Function 133
Custom Function 134
Custom Function 135
Custom Function 136
Custom Function 137
Custom Function 138
Custom Function 139
Custom Function 140
Custom Function 141
Custom Function 142
Custom Function 143
E/P
1
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
M
I
2
3
4
5
6
M
D
P
D
P
D
P
D
D
7
8
9
10
11
12
13
14
♦Access Levels**
♦ Security Level ?
♦ Disarm Level ?
* Command Center Function Authority Level Options: Blank = Disabled, E = Enabled.
Authority Level 15 can not be edited.
♦ D9412x/D7412x only.
** Access Authority Level Options:
Security Level?
M = Any Armed State, P = Perimeter Armed, D = Disarmed, Blank = No
Access
Disarm Level?
I = Disarm to Perimeter Instant, D = Disarm All, Blank = No Disarm Rights
Bosch Security Systems | 12/15 | F01U036089-04
85
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 000 to 038)
User
###
Passcode
Note: Text shown in Times font (ex. 15)
User
Area Authority
Group
1
2
3
4
5
6
7
8
User Name
15
15
15
15
15
15
15
15
SERVICE
000
1 2 3 __ __ __
001
123456 ________
____
1_
__
__
__
__
__
__
__
USER 1
002
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 2
003
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 3
004
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 4
005
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 5
006
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 6
007
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 7
008
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 8
009
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 9
010
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 10
011
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 11
012
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 12
013
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 13
014
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 14
015
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 15
016
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 16
017
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 17
018
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 18
019
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 19
020
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 20
021
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 21
022
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 22
023
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 23
024
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 24
025
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 25
026
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 26
027
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 27
028
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 28
029
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 29
030
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 30
031
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 31
032
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 32
033
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 33
034
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 34
035
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 35
036
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 36
037
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 37
038
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 38
PASSCODE
Product Handler Note: RADXUSR1 is for Users 000 - 124; RADXUSR2 is for Users 125 - 249.
86
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
♦ User (Token) Worksheet (User 000 to 038) D9412x/D7412x Only
Use
r
Master ID ###-0
Sub-User ###-1
Sub-User ###-2
Sub-User ###-3
###
Site
Site
Site
Site
000
Not Available
Card Data
Card Data
Card Data
Card Data
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
Bosch Security Systems | 12/15 | F01U036089-04
87
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 039 to 075)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
039
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 39
040
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 40
041
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 41
042
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 42
043
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 43
044
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 44
045
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 45
046
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 46
047
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 47
048
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 48
049
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 49
050
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 50
051
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 51
052
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 52
053
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 53
054
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 54
055
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 55
056
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 56
057
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 57
058
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 58
059
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 59
060
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 60
061
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 61
062
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 62
063
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 63
064
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 64
065
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 65
066
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 66
067
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 67
068
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 68
069
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 69
070
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 70
071
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 71
072
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 72
073
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 73
074
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 74
075
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 75
88
User Name
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
♦ User (Token) Worksheet (User 039 to 075) D9412x/D7412x Only
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
Bosch Security Systems | 12/15 | F01U036089-04
89
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 076 to 114) (101-249 = D9412x only)
User
User
###
Passcode
076
1
2
3
4
5
6
7
8
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 76
077
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 77
078
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 78
079
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 79
080
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 80
081
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 81
082
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 82
083
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 83
084
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 84
085
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 85
086
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 86
087
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 87
088
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 88
089
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 89
090
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 90
091
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 91
092
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 92
093
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 93
094
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 94
095
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 95
096
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 96
097
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 97
098
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 98
099
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 99
100
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 100
101
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 101
102
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 102
103
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 103
104
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 104
105
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 105
106
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 106
107
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 107
108
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 108
109
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 109
110
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 110
111
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 111
112
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 112
113
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 113
114
__ __ __ __ __ __
__
__
__
__
__
__
__
__
USER 114
90
Group
Area Authority
User Name
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
♦ User (Token) Worksheet (User 076 to 114) D9412x/D7412x Only (101-249 = D9412x only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
Bosch Security Systems | 12/15 | F01U036089-04
91
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 115 to 150) (101-249 = D9412x only)
User
92
User
###
Passcode
115
Group
Area Authority
1
2
3
4
5
6
7
8
User Name
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 115
116
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 116
117
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 117
118
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 118
119
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 119
120
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 120
121
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 121
122
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 122
123
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 123
124
__ __ __ __ __
__
__ __ __ __ __ __
End RADXUSR1 Handler
__
USER 124
125
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 125
126
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 126
127
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 127
128
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 128
129
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 129
130
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 130
131
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 131
132
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 132
133
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 133
134
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 134
135
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 135
136
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 136
137
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 137
138
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 138
139
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 139
140
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 140
141
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 141
142
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 142
143
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 143
144
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 144
145
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 145
146
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 146
147
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 147
148
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 148
149
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 149
150
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 150
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Token) Worksheet (User 115 to 150) (101-249 = D9412x only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
115
116
117
118
119
120
121
122
123
124
End RADXUSR1 Handler
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
Bosch Security Systems | 12/15 | F01U036089-04
93
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 151 to 189) (101-249 = D9412x only)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
151
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 151_
152
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 152_
153
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 153_
154
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 154_
155
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 155_
156
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 156_
157
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 157_
158
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 158_
159
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 159_
160
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 160_
161
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 161_
162
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 162_
163
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 163_
164
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 164_
165
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 165_
166
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 166_
167
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 167_
168
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 168_
169
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 169_
170
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 170_
171
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 171_
172
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 172_
173
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 173_
174
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 174_
175
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 175_
176
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 176_
177
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 177_
178
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 178_
179
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 179_
180
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 180_
181
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 181_
182
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 182_
183
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 183_
184
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 184_
185
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 185_
186
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 186_
187
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 187_
188
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 188_
189
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 189_
94
User Name
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Token) Worksheet (User 151 to 189) (101-249 = D9412x only)
User
Master ID ###-0
Sub-User ###-1
Sub-User ###-2
Sub-User ###-3
###
Site
Site
Site
Site
Card Data
Card Data
Card Data
Card Data
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
Bosch Security Systems | 12/15 | F01U036089-04
95
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 190 to 226) (101-249 = D9412x only)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
User Name
190
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 190
191
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 191
192
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 192
193
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 193
194
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 194
195
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 195
196
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 196
197
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 197
198
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 198
199
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 199
200
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 200
201
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 201
202
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 202
203
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 203
204
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 204
205
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 205
206
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 206
207
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 207
208
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 208
209
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 209
210
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 210
211
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 211
212
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 212
213
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 213
214
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 214
215
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 215
216
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 216
217
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 217
218
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 218
219
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 219
220
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 220
221
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 221
222
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 222
223
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 223
224
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 224
225
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 225
226
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 226
96
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
♦ User (Token) Worksheet (User 190 to 226) D9412x/D7412x Only (101-249 = D9412x only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
Bosch Security Systems | 12/15 | F01U036089-04
97
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (User 227 to 249) (101-249 = D9412x only)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
User Name
227
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 227
228
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 228
229
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 229
230
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 230
231
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 231
232
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 232
233
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 233
234
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 234
235
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 235
236
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 236
237
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 237
238
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 238
239
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 239
240
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 240
241
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 241
242
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 242
243
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 243
244
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 244
245
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 245
246
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 246
247
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 247
248
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 248
249
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 249
98
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Token) Worksheet (User 227 to 249) (101-249 = D9412x only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
Bosch Security Systems | 12/15 | F01U036089-04
99
D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet
User (Passcode) Worksheet (Blank)
User
###
100
Passcode
User
Group
__ __ __ __ __ __
__ __ __ __ __ __
Area Authority
User Name
1
2
3
4
5
6
7
8
____
__
__
__
__
__
__
__
__
USER ___
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Security System Limitations
User (Token) Worksheet (Blank)
Use
r
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Security System Limitations
Not even the most advanced security system can
guarantee protection against burglary, fire, or
environmental threats. All security systems are
subject to possible compromise or failure-towarn for a variety of reasons including, but not
limited to, the following:
•
•
Sub-User ###-2
If sirens or horns are placed outside the
hearing range of people in remote areas of
the building or in areas, which are frequently
closed off, they do not provide the intended
protection.
If intruders gain access through unprotected
points of entry, the system will not detect
their entrance.
Bosch Security Systems | 12/15 | F01U036089-04
Site
•
•
•
Card Data
Sub-User ###-3
Site
Card Data
If intruders have the technical means of
bypassing, jamming, or disconnecting all or
part of the system, they will not be detected.
If the AC power supply is OFF and the backup battery is either missing or dead, sensors
will not detect intrusion.
Smoke detectors cannot detect smoke in
chimneys, walls, or roofs, or smoke blocked
by a closed door. They may not detect smoke
or fire on a level of the building different from
the one on which they are located. Smoke
detectors may not be able to warn in time
about fires started by explosions, improper
storage of flammables, overloaded electrical
circuits, or other types of hazardous
conditions.
101
D1260/D1260B | Owner's Manual | Appendix - Fire Safety and Evacuation
•
If phone lines are out of service, reports from
the security system to the Security Company
cannot be sent unless there is an alternate
means of communication. Telephone lines are
vulnerable to compromise by several means.
Inadequate maintenance and failure to test are
the most common causes of alarm failure. It is
strongly recommended that you test your system
once a week to be sure that all system
components are working properly.
Although having a security system may make you
eligible for reduced insurance premiums, the
system is no substitute for insurance. Warning
devices cannot compensate you for loss of life or
property.
Fire Safety and Evacuation
Residential fire is a leading cause of accidental
death. Most fire related deaths occur at night
when occupants suffocate in their sleep from
smoke and toxic gases, rather than from burns.
To help reduce this risk, the following program
should be implemented.
1. Minimize fire hazards. Smoking in bed,
cleaning with flammable liquids such as
gasoline, leaving children home alone, and
using unsafe holiday decorations are some of
the common causes of household fire.
2. Install a fire alarm system. The primary
purpose of this system is to protect lives by
giving the earliest possible warning of danger.
3. A smoke detector should be provided to
protect each sleeping area in a home
(Figure 4 and Figure 5).
Figure 4: Smoke Detector Locations (Plan
View)
4
2
5
3
1
6
1
3
3
1 - Smoke Detector
4 - Dining Room
2 - TV Room
5 - Kitchen
3 - Bedroom
6 - Living Room
Figure 5: Smoke Detector Locations
(Elevation View)
2
2
1 - Smoke Detector
1
1
2
2 - Bedroom
4. Practice an escape plan. Because there may
be very little time between detection of a fire
and the time it becomes deadly, it is
important that every member of the family
understand how to quickly evacuate
according to the plan.
5. Plan both primary and alternate escape
routes. Since stairwells and hallways may be
blocked during a fire, exiting through a
bedroom window must be a part of the
escape plan. If the sleeping area is above the
ground floor, install a means of safely
descending outside the building if one does
not already exist.
102
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Standard Displays
6. As a part of this plan, all family members
should arrange to meet at a location away
from the house (such as a neighbor’s house)
so you will know that everyone is accounted
for.
Figure 6: Escape Route
2
5
4
3
3
7
3
6
The command center emits a tweedle tone and
alternates between Enter Passcode and press
the ENTER key to disarm and AREA 1
WAREHOUSE is in entry delay. (AREA 1
WAREHOUSE is used as an example.)
You must turn off the system before entry delay
time expires to avoid creating an alarm event.
1
1 - Fire
5 - Dining Room
2 - Escape Routes
6 - Living Room
3 - Bedroom
7 - Smoke Detector
4 - Kitchen
7. If it is determined that the alarm was
accidentally sounded, the bell should be
silenced, the detectors reset, and your
security company notified immediately that
there is no emergency situation.
Exit Now
Arming your system starts exit delay time. The
command center emits a repeating beep tone
and displays AREA 1 WARE HOUSE is now
arming for 3 seconds and then displays Exit
Now!.
Standard Displays
Your command center uses standard and custom
displays to show the status of the security
system. Many standard displays are described
below. Your system may not use all of them.
Descriptions of your custom text follow.
System Command
Displays when you press the COMMAND key. The
system is waiting for you to enter a one or two
digit number to complete the command.
No Authority
The system does not recognize the passcode
entered.
Perimeter Delay
Enter Passcode to Disarm
When the system is turned on, entering through a
delay door starts entry delay time.
Bosch Security Systems | 12/15 | F01U036089-04
Indicates that the perimeter is armed (turned on)
with entry/exit delay time. (See Turning On the
System With Delays )
103
D1260/D1260B | Owner's Manual | Appendix - System Trouble Displays
Service Parameter
Perimeter Instant
Indicates that the perimeter is armed (turned on)
without entry/exit delay time. (See Turning On
the System Without Delays).
Indicates a problem with the panel. Your panel
may not be operating properly (Your Alarm
Company will be replaced with the name of your
security company). Call your security company
for service.
Service Low Battery
First Disarm – Area must be disarmed first
Indicates that the function requested can only be
performed when the area is disarmed. Disarm the
area to perform the function.
Indicates the security system’s battery is low, or
temporarily draining faster than the system can
charge it. If this display remains or appears
frequently, call your security company for service.
Service AC Fail
System Trouble Displays
If you see any of the system trouble displays
shown below, contact your security company to
determine whether repairs are needed.
The Silence> soft key is only
displayed if a trouble tone is present.
Press the Silence> soft key to silence
the following trouble conditions.
Indicates that AC power to the security system is
interrupted. Check the plug-in transformer and
circuit breaker. Entering COMMAND 4 silences
the trouble buzz. The display clears when AC
power returns.
Service Missing Battery
Call for Service
Call your security company. Your security system
may have failed (Your Security Co. will be
replaced with the name of your security
company).
104
Indicates the security system’s battery is
disconnected or shorted.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - System Trouble Displays
Service Communication Fail
Your security system makes repeated attempts to
communicate with the security company.
Indicates that a local printer (if installed) at your
premises is in a trouble condition. Check to be
sure the printer is powered on, the paper is
correctly is inserted, and the printer is selected.
Contact your security company if you have
questions or the display doesn’t clear. You
system may not include a local printer.
Service D9210
In the event your security system fails to
communicate, the command center buzzes and
displays
Comm Fail Route Grp1 (Route Group number
can be from 1 to 4)
Notify your security company of the
communication trouble.
Service Keypad
Indicates that one of the D9210 Access Control
Modules (possible of 8 total) connected to the
panel has encountered a problem. Contact your
security company.
Service Point Bus 1 (or 2)
Indicates that a command center, other than the
one displaying the message, is in a trouble
condition. Notify your security company.
Service Phone Line #1 (or #2)
Displays when a problem has occurred with the
panel’s Point Bus Wiring. Call your security
company.
Fire Point Bypass
Indicates telephone line trouble. Call your phone
company from another phone to report
telephone trouble. This message may not appear
in some systems.
This display indicates that fire points have been
bypassed.
Service Printer
24 Hour Point Bypass
Printer number could also be 18 or 19
This display indicates that 24-hour points have
been bypassed.
Bosch Security Systems | 12/15 | F01U036089-04
105
D1260/D1260B | Owner's Manual | Appendix - Security System Glossary
Security System Glossary
Area
A group of detection devices
connected to your security system.
Arm
To turn on your controlled points
(burglar detection devices). When
an area is armed and a controlled
point trips, an alarm occurs or
entry delay begins. When an area
is disarmed, faulting controlled
points does not generate alarms.
Authority
Level
Your security company or security
representative assigns an authority
level to your passcode. The
authority level determines what
command center functions you can
execute.
Bypass
Selectively remove points from the
security system. You might bypass
a point in order to arm the
perimeter with a window open.
Central
Station
Closing
Report
Command
Menu
106
A facility where trained personnel
monitor your security system 24
hours a day. Your security system
may be programmed to contact
the central station during alarm
conditions, enabling central
station personnel to dispatch the
proper authorities.
A report your system can be
programmed to send to the central
station indicating that an area has
been armed. Opening and closing
reports are commonly used by
commercial accounts.
A list of functions programmed by
your security company. They can
perform most command center
functions with only two or three
keystrokes.
Entry
Delay
A programmed delay of system
alarm response, which allows you
to enter an armed area through
the correct point and disarm the
area. If you don’t disarm before
the delay time expires, the system
begins an alarm response, which
may include reports to the central
station.
Exit Delay
A programmed delay of system
alarm response, which allows you
to exit after arming an area. If you
don’t exit before the delay time
expires, entry delay begins. You
must disarm the system. If you
don’t disarm before the delay time
expires, the system begins an
alarm response, which may include
reports to the central station.
Faulted
Point
A point that is not normal (a door
or window is open).
Force Arm
To turn on (arm) the security
system even though one or more
points are faulted. Force arming
bypasses the faulted points.
Idle Text
The security system displays idle
text at command centers when it
is not performing a user-requested
function. Idle text shows the
arming status of the system.
Master
Arm
To turn on (arm) both interior
points and perimeter points.
Menu
A list of functions you execute
from a command center.
Opening
Report
A report your system can be
programmed to send to the central
station indicating that an area has
been disarmed. Opening and
closing reports are commonly
used by commercial accounts.
Perimeter
Arm
An arming command that arms
only the perimeter points.
Bosch Security Systems | 12/15 | F01U036089-04
D1260/D1260B | Owner's Manual | Appendix - Maintenance and Service
Point
Relay
Trouble
A detection device or group of
devices connected to your security
system. Points display individually
at the command center with
custom text. The text can describe
a single door, motion sensor,
smoke detector, or an area such as
UPSTAIRS or GARAGE.
Your system may have relays
programmed to provide control of
devices such as premises lighting
or entry gates. Your security
company programs relays for
automatic control and/or control
from your command center.
A service condition that needs to
be corrected, such as a broken
wire
Maintenance and Service
This security system requires very little
maintenance, however, you should test the
system weekly to ensure it is working properly. A
test schedule and maintenance program can be
arranged. If you notice a change in operation
during normal use or testing, call for service as
soon as possible. Do not attempt to repair the
control panel, command centers, or detectors
yourself.
How to Clean the Command Center
If your command center gets dirty, apply a
household glass cleaner to a clean cloth or paper
towel and wipe the surface. Do not spray any
liquid directly onto the command center. It could
run inside the case and damage electrical
circuits.
Your Alarm Company
Name:
Call This
Number
Before
Testing
Bosch Security Systems | 12/15 | F01U036089-04
107
Bosch Security Systems
130 Perinton Parkway
Fairport, NY 14450-9199
www.boschsecurity.com
© 2015 Bosch Security Systems
F01U036089-04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising