Puratek Aquarium Reverse Osmosis / Deionization

Puratek Aquarium Reverse Osmosis / Deionization
Puratek Aquarium Reverse Osmosis
/ Deionization
Installation and Maintenance Manual
Thank You for your purchase of a Puratek System by Vertex™ Aquaristik. With
proper installation and maintenance, this system will provide you with high quality
water for years to come. All Puratek products are rigorously tested for safety,
efficiency and reliability.
We prioritize with ease of use, Maximum Purity & Minimum Waste water
production.
Please take a moment to read these instructions to ensure optimal performance.
When using or installing electrical devices, take care and/or consult a
professional. Your safety is our number one concern.
Important Reminders
Be sure to follow these directions carefully. Failure to do so may result in damage
to your Puratek RO/DI Unit and or possible damage to property.
Dealers and or the manufacturer are not responsible & cannot be held
accountable for any personal or property damage resulting from the use or
misuse of this product.
Carefully remove your new Puratek RO/DI Unit from its original packaging,
inspect the unit for damages. All damages must be reported to your dealer
WITHIN 48 hours of receipt and marked by the delivery driver on the waybill.
Each Puratek RO/DI Unit will have the following parts:
-
Top Bracket including: Booster pump, Oil filled pressure gauge, Electronic
Controller, Electronic Components, Reverse Osmosis Chamber
100 GPD Reverse Osmosis Membrane
Clear Canister for Sediment filter and sediment filter.
Clear Canister for Carbon block and Carbon block.
Clear Canister for DI Cartridge and DI Cartridge.
0.25” OD tubing.
Water line connections & Accessories.
Filter Housing wrench.
Once you have verified that there is no damage and that all the parts are present,
you may begin installation.
System Specifications
Power:
Daily Production:
Inlet Water Temperature:
Main Rejection:
Treatment Stages:
Back Flush:
Product to Waste water Ratio
AC110V-DC24V
100GPD / 264l
5-45℃ / 41-113 F
99%
4
Automatic
Approximately 1:1.5
Reverse Osmosis layout and components
This unit is fully automated by using a Microprocessor Controller.
Installation
Chambers when facing the Puratek unit
4
Left
right
3
2
1
1- Insert Sediment filter in Canister # 1.
2- Insert Carbon block in Canister # 2.
3- Insert DI Cartridge in Canister # 3.
4- Insert RO Membrane in Canister # 4.
5- Tighten shut all canisters & use silicone lubricant on O-rings if necessary.
6- Connect the Water line Connector supplied to the Cold water line, use
Teflon tape to ensure complete seal.
7- Connect the water inlet on Chamber # 1 to water source using the tubing
supplied.
8- Connect Tubing to the Water Outlet on Chamber #3 using the tubing
supplied. This is your product water supplying a reservoir or pressurized
tank.
9- Connect the Waste water line (blue color tube) attached to the unit to drain.
10- Force all tubing in the quick disconnect fittings all the way& reinsert the
blue security lock back on.
11- Turn on the source Water.
12- Recheck to see all connection are complete & canisters are shut properly.
13- Plug the unit into the wall receptacle.
After following the above steps, your installation is. Dispose of the product
water for the first half hour after installation, repeat the same practice after
future membrane exchanges every time.
Microprocessor controller Functions
-
The Microprocessor is programmed for 10second delay.
After the delay the unit will flush itself for Maximum efficiency, this will last
for 15 seconds. The Microprocessor’s flush LED is on during this function.
After flushing the Membrane, the unit starts producing water. The
Microprocessor’s making RO LED is on during this function.
While producing water, the LCD will display the water purity in Parts per
millions.
It will take 20 seconds for the unit to display the correct calibrated PPM.
If the water source is interrupted, the unit will shut itself off & the Source
water LED will go on.
The unit is programmed to flush itself once every 2 hours for 15 seconds,
during this function the Flush light will go on.
The unit is equipped with high pressure switch which will turn itself off if
the outlet water line closed by means of float valve or any other.
Filter change instruction
1- Turn Off the unit and disconnect from Electricity.
2- Shut off the water supply
3- Release the pressure from the water outlet by manually opening the float
valve or any other valve used for water shut off.
4- Use filter housing wrench to open the Canisters.
5- Replace the filters.
6- Make sure the O-Ring is in place, and turn the housing counter-clockwise
to close.
7- Make sure there are no leaks then turn the water supply on.
8- After changing the RO Membrane, dispose of the product water for half
hour.
Filters and Membrane storage
*Sediment & Carbon Block Filters do not have a shelf life.
*Reverse Osmosis Membranes could be stored in the refrigerator for up to one
year in it’s sealed original packaging. If the membrane dries out, it will not
produce water.
*DI Cartridges can be kept in a cool & dry place for at least one year in it’s
sealed original packaging.
Trouble shouting Guide
PROBLEM
CAUSE
SOLUTION
Milky colored
Air in system
Air in the system is a normal occurrence with
water
initial startup of the Unit. This will disappear
after some times.
Slow production
Low water pressure
This system requires min 40 psi incoming
Crimps in tubing
water pressure. Check booster pump.
Clogged pre-filters
Replace pre-filters
Fouled membrane
Replace membrane
Check tubing for crimps or blockage
Offensive smell
Fouled membrane
Replace membrane
Dirty Tank/ Reservoir
Drain and storage tank
No waste water
Clogged flow restrictor
Replace flow restrictor
Leaks
Fitting not tightened
Tighten fittings as necessary.
Missing o-ring
Reinstall the O-ring
Misalignment of hole in Realign drain saddle.
drain saddle
For more information about this or any other Vertex™ products contact
your dealer or visit us at:
www.vertexaquaristik.com
Thank you
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising