zioncom ip路由器用户手册

zioncom ip路由器用户手册
User’s Guide
Great thanks for your purchasing ipTIME PRO 54G Wireless Router ,ipTIME
PRO 54G Supports IEEE802.11G Standard ,transferring date with speed of 54Mbps ,
also conforms to IEEE802.11B Standard. ipTIME PRO 54G satisfy enterprise with
small scale, SOHO user to lay out WAN and LAN. ipTIME PRO 54G provide
multi-protection for the security for the networks, such as support or prohibit SSID
broadcast, not allow AP to broadcast SSID network name for SSID prevention.
ipTIME PRO 54G support WEP for the security of WLANS with powerful firewall.
ipTIME PRO 54G allow many PCs to share one PC’s WAN Cable and one Internet
account by ISP. ipTIME PRO 54G allow varies ways to internet, such as ADSL,
Cable Modem, dial up automatically, easy to configure. ipTIME PRO 54G combines
4 port Ethernet Switch to connect with Ethernet adapters. VLAN server allow Internet
user to visit website, FTP and other service in LAN. ipTIME PRO 54G control the
outside visit, configure different authorized access. ipTIME PRO 54G support Web
management, DMZ, network game and videoconference.
This manual is the user’s guide for ipTIME PRO 54G.
This manual consists of hardware specification, installation guide, configuration
guide and definition on how to use ipTIME PRO 54G.
Pls use this manual for your reference.
First, Pls read the installation guide in chapter 4, note some points when install.
Second, Pls read chapter 6, in order to allow ipTIME PRO 54G to run in
corresponding Internet environment.
-1-
www.zioncom.net
User’s Guide
TABLE OF CONTENTS
1. WARNING…………………………………………………….……..…..4
2.PACKAGE CONTENTS…...…………………………………………...5
3.SPECIFICATION………………………………………………………..6
4.INSTALLATION………………………………………………………...10
4.1 Before Installation………………………………………………………………10
4.2 Installation ……………………………………………………………………....11
4.3 Sketch Map ……………………………………………………………………..14
5. LOCAL COMPUTER SETUP….……………………………….........15
5.1 Windows 2000 SETUP…………………………………………………………15
5.2 Windows XP SETUP……………………………………………………..….....19
6. IP ROUTERSETUP ………………………………………..………….24
6.1 Start Internet Explore to Login……………………………………..…………..24
6.2 PPPoE Configuration …………………………………………………………..24
6.3 Dynamic IP(Cable Modem...) Configuration………………………………… 30
6.4 Static IP Configuration …………………………………………………………35
6.5 Status…………………………………………………………………………….38
6.5.1 WAN Status………………………………………………………………...38
6.5.2 Wireless Status………………………………………………………….....39
6.5.3 LAN Status ………………………………………………………………....40
6.6 Basic Configuration ………………………………………………………….....41
6.6.1WAN Configuration …………………………………………………….…..41
6.6.2 Wireless Configuration ……………………………………………..……..41
6.6.3 LAN Configuration……………………………………………………...….44
6.6.4 Connection Configuration ……………………………………………......46
6.6.5 IP Routing List ……………………………………………………..…...…48
6.7 System………………………………………………………………………..…49
6.7.1 Administrator Configuration …………………………………………......49
6.7.2 System Up gradation ……………………………………………………..50
6.7.3 System Memorandums………………………………………………..….54
-2-
www.zioncom.net
User’s Guide
6.7.4 Others Configuration ………………………………………………….....54
6.8 QoS……………………………………………………………………………...56
6.8.1Basic Configuration …………………………………………………….....57
6.8.2 IP QoS……………………………………………………………………...57
6.8.3 Application Programme QoS…………………………………...………..58
6.8.4 Ports QoS…………………………………………………………………..60
6.9 NAT………………………………………………………………………………61
6.9.1Application ……………………………………………………………….....61
6.9.2 Virtual Server……………………………………………………………....63
6.9.3 Port Transfer ……………………………………………………………....67
6.9.4 Port Trigger………………………………………………………………...68
6.9.5 NAT ON/OFF………………………………………………………..……..69
6.10 Advance Configuration ……………………………………………………....70
6.10.1 Firewall…………………………………………………………………….70
6.10.2 DDNS…………………………………………………………………...…72
6.10.3 Remote Wake-up……………………………………………………...…74
6.10.4 URL Filtering …………………………………………………………..…76
6.10.5 Remote Management…………………………………………………....76
6.10.6 Time Management ………………………………………………….…...78
6.10.7 VPN…………………………………………………………………….….79
Appendix A. UTP Cable specification………………………………….….……...81
-3-
www.zioncom.net
User’s Guide
1. Warning
1.
Pls used adaptor provided by manufacturer, otherwise will break ipTIME
PRO 54G.
2.
Do not drop IP Router down or any damage to the Router and its
electronic component.
3.
Do not disassemble IP Router, otherwise warranty for repair will not be
guaranteed
4.
Do not exposure IP Router under Sunshine, to avoid heat.
5.
Pls keep IP Router dry and away from fire.
6.
Pls keep IP Router under shield and run under 0-40 to the perfect state.
-4-
www.zioncom.net
User’s Guide
2. PACKAGE CONTENTS
Package contents of Wireless IP Router as follows:
1.
Wireless IP Router ipTIME Pro 54g
2.
Switch DC Power Adapter (7.5V,1.5A)
3.
Ethernet Cable
4.
User’s Guide
-5-
www.zioncom.net
User’s Guide
3.SPECIFICATION
This Wireless IP Router is a highly integrated Wireless IP Router with many
functions such as Gateway, Switch, DHCP server, Firewall etc:
11G 54Mbps : Support 802.11g , high-speed data rate up to 54Mbps for
802.11g(draft) and 11Mbps for 802.11b with wide range coverage.
Network Address Transform (NAT):With providing Internet application this IP
Router can allow more than one user to connect with Internet at the same time by
sharing one public IP address; It supports many connection ways:xDSL、Cable
Modem、LAN/ Leased Line and so on.
4 Ports 10/100M Switch:It has 4 Network 10/100M switch ports,port support
MDI/MDIX automatic identification function, Switch port can connect to other
switches, so that can support over hundred computers to go to Internet at the same
time.
PPPoE(ADSL) Automatic Disconnection/Connection : Users can optionally
choose automatic disconnection in idle time and connection in access time to save
Internet access cost.
DHCP Server Supported:All of the networked computers can retrieve TCP/IP
settings automatically from this product.
Static IP address Binding: Authorize user to manage and configure PC in LAN in
most by binding MAC address and IP address together.
System Memorandum: ipTIME pro 54g record routing history and forwarder to
administrator mailbox.
UPnP: Defaulted UPnP enable user to configure networking hardware and software.
Management Based on Web Page : Both network configuration and system
configuration are based on inside Web Server. The user interface is clear and usage
is easy. By this interface users can also update software to enhance the system
stability and expansibility.
Internet Access Control:Different administration can be setup for different users.
Data Package Filtration: Port Filtration, IP Address Filtration, MAC Address filtration,
Key word Filtration enable user to configure IP router to analyze data package can
be forwarded or refused.
-6-
www.zioncom.net
User’s Guide
Virtual Server:Allow other users from Internet access WWW, FTP server or other
servers in LAN.
QoS: Control the IP Router bandwidth forwarding and transferring by configuration
IP Address QoS , application QoS and port QoS.
Firewall:Users can randomly refuse or allow data from Internet
Scheduler: Manage and control Local Network accessing Internet by configuration
time.
DMZ Server:Allow one computer to be totally open to Internet to make sure special
application.
Remote Management:Users can totally manage office or home network wherever
they are.
DDNS:By this function users can set up their own web station.
Remote Wake-up: Enable user to remote wake up PCs in LAN.
Support VPN Pass-through:Supports VPN Pass-through PPTP dialogue,and also
supports users to configure VPN Server and Client in LAN.。
VPN server: Allow you to setup VPN server, allow 5 VPN client logging at same time
Detailed Specification
ITEM
Standard
Protocol
SPECIFICATION
External
WIRELESS IP ROUTER
IEEE 802.11G、IEEE 802.11B、IEEE 802.3、IEEE 802.3u、
IEEE 802.3x、
TCP/IP, NAT, DHCP, UDP, FTP, PPPoE, PPTP,
L2TP,HTTP,DNS, IPSec/VPN Pass-through…
WAN
Port
LAN
Wireless
Frequency
Parameter
Range
One 10/100Mbps RJ-45 port, automatic
sense cross cable
Four 10/100Mbps speed Ethernet switch
port, auto sense cross cable
2.412~2.472 GHz
Forward
1, 2, 5.5, 11Mbps(802.11b)
Speed
6, 9, 12, 18, 24, 36, 48, 54 Mbps (802.11g)
-7-
www.zioncom.net
User’s Guide
Opt.
Channel
Data
Modulation
Cable
Control
interface
14
CCK, DQPSK, DBPSK, OFDM
RF Power
16-18dBm
Antenna
1*2.4Ghz Dipole Antenna
Type
1*2.4Ghz Embedded Antenna
UTP100Base-TX:UTP/STP 5 or above standard
Based on Web application
-8-
www.zioncom.net
User’s Guide
10/100Mbps switch
LAN/WAN port auto sense cross cable
WAN port static/dynamic IP flexible setting up
Support 64/128 bit WEP and MAC
Support AP client Bridge-Point-to Point mode
Support client mode
PPPoE dial-up and connection time setting up
PPPoE dial-up and automatic/manual connection
Double IP Configuration
Support VPN Pass-through
DHCP Service
DNS relaying
DMZ Server
Inside
Static IP Address Binding
function
System Memorandum forwarding
IP Router configuration back-up
UPNP
Connection setting up and stat.
Time control on access to internet
Firewall
NAT ON/OFF
Port/IP/MAC/Key word Filtration
Remote control
Remote Wake-up
DDNS
Gateway
Virtual Server
Qos & VPN Server
-9-
www.zioncom.net
User’s Guide
Product Specification
CPU
KENDIN KS8695PX (ARM9)
FLASH
2MB Flash
Memory
16MB SDRAM
LAN
connection
WAN
connection
Static or dynamic IP address
xDSL、Cable Modem、Special cable、LAN
Power supply
DC 7.5V/1.5A switch power adapter
Size
179mm×*119mm×*39mm
Temperature
0 ~ 60 ℃
Humidity
10 ~ 85%
Compatible OS:
Windows 95/98/ME/NT/2000/XP
Mac OS
Linux or other UNIX system
Notes:
If the specification and functions of IP Router have been changed, it will
not be informed. The users please take care of it by themselves.
4.INSTALLATION
4.1 BEFORE INSTALLATION:
4.1.1. Firstly please confirm your computer OS (Windows 95,98,NT, ME, 2000,
XP, Linux, Mac) and Web browser (Internet Explorer 4.0 with JavaScript
function、Netscape Navigator 4.0 or above version)。
4.1.2. Make sure there is LAN Card which has been correctly installed in your
computer.
4.1.3. If you are xDSL user, please remember your user ID and password.
4.1.4. If you connect Internet by LAN or WAN, please get the following
information from your network administrator: IP address is static or
-10www.zioncom.net
User’s Guide
dynamic, DNS, default gateway, account and so on.
* If your computer has installed ADSL PPPoE dial-up software before the
installation of IP Router, please backup your installation software and uninstall your
ADSL PPPoE dial-up software by Start->control panel->Add or Remove Programs.
4.2 INSTALLATION
4.2.1. Setup WAN connection: connect broadband cable (xDSL, Cable Modem
or LAN/ Leased cable) with WAN port of IP Router.
4.2.2. Setup LAN connection: connect your computer LAN card’s port or your
switch UPLINK port with one LAN port of IP Router by a common
network cable.
Note: All LAN ports of IP Router can automatically sense cross cable, so you
can either use through cable or cross cable to connect LAN card or
switch.
4.2.3. Turn on the power: connect and the power supply, turn on it. Then IP
Router comes to self-detect state. During the self-detect: PWR LED will
be long light, RUN LED will slow flash after correct startup, other four
LAN LED and WAN LED will flash only twice rapidly, then the system will
come to normal work state.
4.2.4. Start computer
LED
Description
Explanation
PWR
Power LED
Long light
LED flash when device work normally.
RUN
System status LED
LED doesn’t on or flash refer some problem
with device
WLAN
WAN
LAN
WLAN
port
connection LED
WAN
port
connection LED
LAN
port
Flashing refers to data transformation
Flashing refers to data transformation
Flashing refers to data transformation
-11www.zioncom.net
User’s Guide
connection LED
WLAN
PWR
RUN
WAN
LAN 1 ~ 4
Port explanation
Antenna
Power jack
Reset
Antenna provide wireless LAN functionality and
ensure optimal signal strength
Connect power adapter (7.5V/1.5A)
Press Reset button. Switch the power off/on. After
switching the power on, about 5 seconds later
-12www.zioncom.net
User’s Guide
RUN LED will flash rapidly, then release the
button. After IP Router startup, all configurations
will restore to default configuration.
WAN
LAN 1~4
Connect xDSL/Cable Modem or Special cable
Connect personal computer or hub, switch and so
on
Antenna
Power Port
Reset
WAN
LAN 1 ~ 4
NOTE:After switch or hub expand, Wireless IP Router can connect at most 253
client computers in LAN or WLAN.
-13www.zioncom.net
User’s Guide
4.3 NETWORK SKETCH MAP
Note:During the usage, the sequence of turn on is:firstly turn on Modem’s
power supply ,1 minute after Modem startup turn on IP Router power supply ,
then turn on the computer .
-14www.zioncom.net
User’s Guide
5.
LOCAL COMPUTER SETUP
Users should configure local network to access Internet by IP Router.
Users should know the default configuration of IP Router before installation.
Users must connect with IP Router again after configure computer’s local
network. Please make sure your computer setting is as follows, Otherwise IP
Router can not be correctly connected (Linux and Mac users please setup as
follows by relative conference).
The default configuration of IP Router is:
— IP address:192.168.0.1
— Subnet Masks:255.255.255.0
Users can setup static or dynamic IP configuration.
5.1 Windows 2000 SETUP
(1)
Install IP Router.
(2)
Start Windows 2000 and check LAN LED is on or off. If off, please confirm
the connection of your computer with IP Router.
(3)
Click “start”->“Setting”->“Panel Control”.
-15www.zioncom.net
User’s Guide
(4)
Double click the “Network and Dial-up Connection” in “control panel”.
(5)
Click “Local area connection”->“Properties”->“Internet protocol
(TCP/IP)”and “Properties”.
(6)
(7)
Click “General ” bar, Select “Obtain an IP address automatically” and “Obtain
DNS server address automatically”
Click “OK”.
-16www.zioncom.net
User’s Guide
(8)
Click ”Start” ->“Run”.
(9)
Input ”cmd” ,then click “OK”.
(10) Input “ipconfig” in Pop-up Command window.
(9) Please make sure your IP is the same with below. If same then your
configuration is successful, or please redo the above steps and restart your
computer.
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
The default gateway is 192.168.0.1
-17www.zioncom.net
User’s Guide
(10) Input “ping 192.168.0.1”, then “Enter”.
(11) If you can see “Reply from 192.168.0.1: bytes=32 time=2ms TTL=64”,then the
connection between your computer and IP Router is completed.
-18www.zioncom.net
User’s Guide
5.2 Windows XP SETUP
(1)
Install IP Router.
(2)
Start Windows XP and check LAN LED is on or off. If off, please confirm
the connection of your computer with IP Router.
(3)
Click “Start”->“Setting”->“Panel Control”
(4)
Double click the “Network and Internet Connections” in “control
panel”.
(5)
Click “Network connection”->“local area
connection”->“properties”-> “Internet protocol(TCP/IP)” and
“Properties”.
(6)
Click “General “, Select “Obtain an IP address automatically” and
“Obtain DNS server address automatically”
(7)
Click “OK”
-19www.zioncom.net
User’s Guide
-20www.zioncom.net
User’s Guide
-21www.zioncom.net
User’s Guide
(8)
Click “Start”->“Run”
(9)
Input “cmd “, Click “OK”
(10) Input “ipconfig” in the pop-up command window.
(11) Please make sure your IP is the same with below. If same then your
configuration is successful, or please redo the above steps and restart
your computer.
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
The default gateway is 192.168.0.1
-22www.zioncom.net
User’s Guide
(12) Input “ping 192.168.0.1”, then “Enter”.
(13) If you can see “Reply from 192.168.0.1: bytes=32 time=2ms TTL=64”,then
the connection between your computer and IP router is completed.
-23www.zioncom.net
User’s Guide
6. IP ROUTER SETUP
6.1
START INTERNET EXPLORRE TO LOGIN
Run Internet Explorer (
) ,and click the “Stop (
) button in
Internet Explorer’s toolbar.
Input http://192.168.0.1 in Internet Explorer’s address bar.
192.168.0.1 is Default IP address of Router.
You may see the following login web page. Click “Login” button and make
relative configuration. Check
“WAN Setup” to Setup Wizard. The setup
wizard enables you to configure the router quickly and conveniently.
Check “WLAN Setup” to WLAN setup wizard. The wireless setup wizard
enables you to configure the wireless setting.
You can login directly without account & password confirmation because
there is no account information required by factory default configuration.
Conn. Type:
IP ROUTER current connection type, Dynamic IP is default
value.
Conn. Status: IP Router current connection Status
WAN IP: IP ROUTER WAN current IP address
Connected PC:
IP address of the computer which connects to IP ROUTER.
-24www.zioncom.net
User’s Guide
6.2
PPPoE(ADSL) USER SETUP
This connection way is suitable for virtual dial-up Internet connection.
Open external ADSL Modem and check the WAN LED of IP ROUTER.
If WAN LED is off, check the network cable between external modem and
WAN port.
Click “Basic setup “-> “WAN setup”, as follows:
-25www.zioncom.net
User’s Guide
Select “PPPoE User (ADSL)” radio button.
Key in the “User ID” and “Password” provided by your Internet service
provider.
Click the “Apply” button.
You may see the popup window.
In case “Conn. Status” is “Successfully connected”, the configuration is
correct.
Click “Show Internet connection status” and see the 6.5.1.
-26www.zioncom.net
User’s Guide
If In case “Conn. Status” is “Invalid ID/password”, the configuration is
incorrect.
Click the “close” button and check your ID& password.
If “Conn. Status” keeps unchanged, check whether your service type is
correct.
Confirm the WAN connection status: If WAN connection is successfully
established, then by clicking “Show Internet Information” you can enter
WAN status web page; or click “Status”-> “WAN status”, as the following.
Connection Type should be PPPoE (ADSL)
Connection Status should be “successfully connected”
-27www.zioncom.net
User’s Guide
Physical Address is shows Router WAN port MAC Address.
WAN IP Address, Subnet mask, Default Gateway, Primary DNS
server and Secondary DNS server can be different from the following
values. (These addresses are provided by your ISP)
“Disconnect” is manual disconnection button. If you click then
the system will disconnect with Internet
-28www.zioncom.net
User’s Guide
“Connect” is manual connection button. By clicking it the
system can be connected to Internet again.
Click “Save” to save current configuration.
Restart all PCs connect with IP Router.
-29www.zioncom.net
User’s Guide
Notes: Please save IP Router Configuration after completion, otherwise
configuration will lose when power off or restart.
Other Configurations:
MTU: Input MTU value of data package, default value is 1454. Normally
please do not change it.
Disconnect PPP session if idle time is longer than
Min: If you
choose this option and setup the time T, then the IP router
automatically disconnects from Internet after T idle time.
Connect On Demand: IP Router can automatically connect with Internet
if there is Internet access after disconnection. Note: during usage if there
is disconnection due to external causes, then the IP Router will try to
connect with Internet at once until successful connection. This function is
the IP Router inner function and does nothing with Connect On Demand
function. Connect On Demand is only effective to Disconnect PPP
session if idle time is longer than
Min.
Connect Manually: By this option users have to connect with Internet
manually after disconnection. This option is only effective to Disconnect
PPP session if idle time is longer than Min.
Prevent reconnection although no response from PPP server: This
option is to shut off IP Router inner automatic connection function. By
choosing this option if external network disconnects, IP Router will not try
to connect at once.
6.3
DYNAMIC IP USER (Cable/Modem…) SETUP
By this connection way IP Router can get IP address automatically from
ISP (such as: CHINA TELCOM). It is suitable for connection ways such as
Cable Modem, LAN and so on.
-30www.zioncom.net
User’s Guide
Turn on the external Cable Modem and check the WAN LED of IP
Router.
If WAN LED is off, please re-confirm the network cable between
external Modem and WAN port.
Click “Basic Setup”->“WAN Setup” as diagram:
Choose Dynamic IP user (Cable Modem…)
Click Apply to complete.
You will see the following pop-up window
If Conn. status is “Successful connected”, the configuration is correct.
Click “Show Internet Information” and see the 6.5.1
-31www.zioncom.net
User’s Guide
If connection status keeps to be “Connecting to Internet”, please do the
following steps:
Close the pop-up window.
Turn off Cable Modem power supply then on, and confirm the WAN LED
status.
Re-click “Apply” button.
Check the WAN Connection Status: If the status is “Successfully
connection”, click “Show Internet Information” to enter WAN status page;
or click Status->WAN status, as following diagram:
-32www.zioncom.net
User’s Guide
If WAN connection is successfully established, you can see the following.
Connection Type should be “Cable Modem (DHCP)”
Connection Status should be “Successful connected”
Physical Address is shows Router WAN port MAC Address.
WAN IP Address, Subnet mask, Default Gateway, Primary DNS
server and Secondary DNS server in your computer may be different
from the following value (These addresses are provided by your ISP).
Disconnect button as follows is manual WAN port IP address release
function button. If click it IP Router will release WAN port IP address and
disconnect with Internet.
-33www.zioncom.net
User’s Guide
“Connect” button is manual WAN port IP address refresh function
button. If click it WAN port will re-get dynamic IP address and connect
with Internet.
Click “Save” button to save current configuration, then restart all PCs
connected with IP Router
-34www.zioncom.net
User’s Guide
Note:
After completed setup, please save IP Router configuration,
otherwise the configuration will be lost when IP Router is power off or
restarts.
Other configuration:
Physical address Clone:If you want to change WAN port MAC
address you can choose this option; If this option is un-chosen the
WAN MAC address is default value; By this option the displayed MAC
address is your current MAC address; You can also manually add the
WAN port MAC address; without the option WAN port MAC address
will restore to default value.
Allow private IP to be accepted: Allow WAN port assigned private IP
address.
6.4
STATIC IP USER SETUP
If you have static IP address provided by ISP, you can choose this option.
Turn on the external modem and check the WAN LED of IP Router
If the WAN LED is off, please check the network cable between
external modem and the WAN port.
Click Basic Setup->WAN Setup as following diagram:
-35www.zioncom.net
User’s Guide
Input WAN IP address, Subnet mask, Default Gateway, Primary DNS
Server and Secondary DNS Server provided by ISP.
Click Apply to complete.
You will see the following pop-up window:
Check WAN connection status: If it is “Configuration is done”, click
“Show Internet Information” to enter WAN status page; or click
Status->WAN status, as following diagram:
-36www.zioncom.net
User’s Guide
If WAN connection is successfully established, you can see the following.
Connection Type should be “Static IP”
Connection Status should be “successful connection”
Physical Address is shows Router WAN port MAC Address.
Confirm WAN IP Address, Subnet mask, Default Gateway,
Primary DNS server and Backup DNS server is same with
the values provided by ISP or not.
Click the “Save” button to keep current configuration, then restart
computers in LAN to re-get IP relative information.
Note:
After completion please save the configuration, otherwise configuration
will be lost when IP Router is power off or restarts.
-37www.zioncom.net
User’s Guide
6.5
STATUS
6.5.1 WAN Status
Click “Status”->“WAN Status” as following:
This page shows current Internet connection status (WAN port), including
Connection Type, Connection Status, WAN IP address, Subnet mask, Default
Gateway and DNS server. If it is dynamic IP way, “Disconnect” button or
“Connect” button will be shown above. Click “Disconnect” button to release
current WAN Port IP Address, then click “Connect” button to refresh WAN IP
address; if it is PPPoE way, then “Connect” or “Disconnect” button will be shown
above. Click “Connect” button to connect with Internet, click “Disconnect” button
to disconnect with Internet.
Refresh:Refresh current web page. All of the following web pages will
have this button with the same function.
Save:Save IP Router current configuration. All of the following web pages
will have this button with the same function.
-38www.zioncom.net
User’s Guide
6.5.2 Wireless Status
Click “Status”->“Wireless Status” as following:
This web show current wireless part configuration, including:
Wireless Status: Show current wireless connector status.
SSID (networking name): Show current wireless networking name.
Mode: Current used wireless connector forwarding mode
Region: Show current channel region information
Channel: show current used channel
SSID Broadcast: Show SSID is on or off
Authentication Type: Show current used certification way
Encryption Strength: Show WEP encryption length (64/128 bits)
MAC Authentication: Show how to identify wireless customer by MAC
address.
-39www.zioncom.net
User’s Guide
6.5.3 LAN Status
Click “Status” –>“LAN Status” as follows:
LAN Information : Show user current LAN connecting status (LAN port and wireless
connection ) and DHCP server status, include MAC address of the LAN port ,and IP
rent regions and quantities of IP address shared by IP Router among IP
address ,subnet mask, DHCP server in LAN .
Shared IP information: Show IP address information rent by DHCP server
Serial Number: The position in the subject
Physical Address: MAC address of the client PC
Types: Wireless /Wired, dynamic / static
-40www.zioncom.net
User’s Guide
6.6
BASIC SETUP
6.6.1 WAN Setup
Click ”Basic Setup”->“WAN SETUP” as following:
The way for Dynamic IP User, PPPoE(ADSL) user and static IP user to set up
are illustrated in Chapter 6.2 ,6.3,and 6.4 respectively . Pls refer to those chapters.
ipTIME PRO 54G not only connect Internet by cable also with other AP by
wireless, named wireless client mode. In this mode, wireless client PC cannot
connect with this Wireless router in wireless way but by cable.
If choose this mode, configure wireless connection as Internet connection,
click ” Applied” and “restart “. This mode enable user to obtain IP in WAN setup.
Note:
1.
In client mode, click “ Basic Setup ”->”Wireless Setup” configure
corresponding SSID and encryption way.
2.
in client mode , wireless router WAN port will be disable.
6.6.2 Wireless Setup
Click ”Basic Setup”->“Wireless SETUP” as following:
This web show the basic wireless parameter and wireless certification way
configuration
-41www.zioncom.net
User’s Guide
Basic Setup: Show current wireless status and basic parameter for
configuration
Status: Show wireless connector status (on/off, AP/Client mode)
Operation: Wireless connector can be configured as on or off.
SSID: Record wireless SSID
Mode: If wireless connector conforms to 11G and 11B standard, pls choose “G
and B”; If wireless connector only run under 11G standard, choose “g only
mode”.
Region: Configure region for wireless channel, no need to setup.
Channel: Choose the wireless networks channel in AP mode; In client mode,
option for channel is disable.
Broadcast of SSID Option: if SSID configured, AP broadcast SSID to wireless
client.
After finishing configuration, click “Apply”.
-42www.zioncom.net
User’s Guide
WEP Setup: Configure Certification way and WEP key.
Authentication Type: Choose authentication type (automatic/open
system/share Key)
Encryption Strength: Choose Key length (64/128bits)
Key Input Method: Choose string, HEX or Pass phrase
Basic Key: Fill in Key value
After finishing configuration, click “ Apply ” .
MAC Authentication: Configure MAC authentication, choose type
(Open/Accept/Reject) and click “Apply”
In open type: All the wireless clients can connect.
In Accept type: Specified clients can connect
In Reject type: Specified client was reject to connect.
-43www.zioncom.net
User’s Guide
Notes:
After setup, pls click “Save”. Save IP Router configuration, otherwise,
configuration will be lost when power off or router restarted.
6.6.3 LAN Status
Click ”Basic Setup”->“LAN/DHCP SETUP” as following:
-44www.zioncom.net
User’s Guide
LAN port basic parameter and DHCP server parameter can be setup in this
web page.
System IP Setup:If you want to change IP Router LAN port address, you
can setup as follows:
System IP address:IP address in LAN. This IP address is factory
default value 192.168.0.1, and you can change it.
Subnet Mask:Subnet mask in LAN. This value cannot be changed.
TCP/IP protocol configuration includes IP address, subnet mask,
Gateway and DNS server and so on. It is not easy to configure TCP/IP
protocol correctly in all computers in LAN, but it is lucky that –DHCP Server
has provided this function. If you choose the DHCP function, you can let
DHCP Server configure TCP/IP protocol in all computers in LAN
automatically.
DHCP Setup: If you want to able or disable DHCP Server, change DHCP
address range, you can choose the following options:
DHCP Server Status:Display DHCP Server current status.
DHCP Server Operation:Able and disable DHCP Server. The default
value is able DHCP Server.
DHCP IP Pool:IP address range automatically allocated by DHCP Server
is address pool.
Manual DNS configuration: Let DHCP Server automatically allocated the
DNS Server to Client PC.
Static Lease Management:This function makes sure the convenient
control of the IP address in LAN computers. Static lease IP can obligate static
IP address for computer with appointed MAC address. Afterwards when the
-45www.zioncom.net
User’s Guide
computer asks DHCP Server for IP address, DHCP Server will give it the
obligated IP address.
Add hardware address & IP pair on the real network: Choose this function,
IP Router list PC IP address and MAC address, specify IP address and MAC
address to be binded, click “Add” to implement binding.
Add hardware address & IP pair manually: Choose this option, user just
input the MAC address and IP address of PC to be binded
Notes:
1.
In order to use DHCP function of the IP Router, TCP/IP protocol of
computers in LAN must be configured as “automatically get IP
address”.
2.
After completion please click “Apply” to make the configuration valid.
Please save the configuration, otherwise configuration will be lost
when IP Router is power off or restarts.
6.6.4Link Setup/Info
Click “Basic setup”->” Link Setup/Info” as follows:
-46www.zioncom.net
User’s Guide
All IP Router ports’ speed, Link information and port statistics data and so on
can be setup by this web page:
Link Setup:Setup every port’s connection speed.
Port:
IP Router WAN Port and LAN Port.
Mode: Automatic mode and manual mode turn on/off.
Speed:Setup port speed.
Apply:Apply current setup.
Link Information:Display all current ports connection status.
-47www.zioncom.net
User’s Guide
Port:IP Router WAN port and LAN port.
Link:Connection port is being used or not.
Speed:Current port speed.
Duplex:If FULL, then it is full Duplex; If HALF,then it is half- Duplex
Link Statistics:Display received and sent-out data flow from every current
port.
Note:
Click “Save” to save this IP Router configuration, otherwise configuration
will be lost when power is off or PC restarted.
6.6.5 Routing Table
Static routes can be added if you require specific routes, Click “Basic
setup”->” Routing Table” as follows:
Type:Routing Type. Have two options: NET/Host.
Target: Enter in the IP of the specified network or host that you
want to access using the static route
-48www.zioncom.net
User’s Guide
Mask: Enter in the subnet mask to be used for the specified network,
For example:255.255.255.0=>24.
Gateway: Enter in the gateway IP address to the specified network.
For Complete Setup, Please click “Add” button to add a Routing rule.
Note:
Click “Save” to save this IP Router configuration, otherwise configuration
will be lost when power is off or PC restarted.
6.7
SYSTEM
6.7.1 PASSWORD
Click “System” -> “Password” as follows:
System administrator ID and password can be changed by this web page.
-49www.zioncom.net
User’s Guide
Firstly please input your old ID and password, and then input your expected new
ones. If your old ID and password which have been input are correct then click
“Apply” to successfully change.
Admi E-Mail Setup: If user wants to receive IP Routing log, configure Email address
and SMTP server to receive.
Note:
1.
According to the safety, we strongly recommend you to change
the initial administrator username and password. If you forget
your system password please change them to factory default
values by Reset button.
2.
If want to restore the default value, Please press Reset button and
pull out the power adapter DC plug then insert the DC plug, about
5 seconds later RUN LED will flash rapidly, then release the
button. After IP Router startup, all configuration will restore to
default configuration.
6.7.2 Firmware Upgrade
Click “System” ->“Firmware Upgrade”,as follows:
IP Router will be obtained new function by upgradetion .
-50www.zioncom.net
User’s Guide
How to upgrade firmware:
Login our website www.zioncom.net, download advanced software to local hard disk;
pls pay attention to model number.
By updating the IP Router software, you can get new functions or
performance.
Software update steps:
1)
Login our company homepage:www.zioncom.net, download new
version software to your local hard disk.
* Please notice production and software type.
2)
Click “Browse” button to choose you downloaded file.
-51www.zioncom.net
User’s Guide
3)
Click “Upgrade” button to upgrade system software.
-52www.zioncom.net
User’s Guide
4)
After update, IP Router will restart automatically.
5)
Please check you firmware version.
Note:
Update phase is about 60 seconds. During the update progress
please do not turn the power off otherwise the IP Router will be damaged.
6.7.3 System log
Click “System” ->“System log”,as follows:
-53www.zioncom.net
User’s Guide
This web record IP router system log and can switch system log status for
checking system history happens on the Router.
6.7.4 Misc.
Click “System” ->“Misc.”,as follows:
-54www.zioncom.net
User’s Guide
Setup Hostname: Configure IP Router name in the networking presented on
the report forwarded to administrator mailbox.
Config Mgmt /Restart:
Config Backup: Enable user to backup all the configurations.
Config Restore: Restore previous configuration on router.
Restore Default: Restore defaulted configuration provided by manufacturer,
including:
Defaulted user name: Blank
Defaulted IP address: 192.168.0.1
Defaulted Subnet Mask: 255.255.255.0
Restore defaulted configuration provided by manufacturer, router will reboot
automatically.
Restart System: Click “Restart System”, router will reboot automatically.
System Time Setup: For sake of Scheduler. pls configure accurate time system.
Refresh router current time in accurate time zone : Or choose other systerm server
until time to be refreshed.
UPNP Setup: UPNP is configured as defaulted. General plug and play UPNP refer
to system architecture for the networking between PC and other universal intelligent
equipments, especially for the SOHO user. UPnP works with wired or wireless
-55www.zioncom.net
User’s Guide
networks and can be supported on any operating system. UPnP boasts
device-driver independence and zero-configuration networking, enable
networking equipments connect automatically and working harmoniously.
6.8
QoS
6.8.1Basic Setup
Click “QoS” ->“Basic Setup”,as follows:
Function: Above web is for user to configure Qos basic functions status, access to
the Internet and bandwidth speed.
Setup Method:
Start up Qos , configure the access to the internet and bandwidth speed under
subject of internet throughput, Qos specify the throughput level of the internet
application, and then click “Apply ”.
-56www.zioncom.net
User’s Guide
Notes:
1.
If
Internet
throughput
configuration
changed,
current
Qos
configuration will be missing.
2.
Save current configuration before router power is off or reboot.
3.
For the management, prefer to static lease IP or using static IP
address on client’s PC.
6.8.2 IP QoS
Click “QoS” ->“IP QoS”,as follows:
Function:
IP Qos enable user to control forwarding and downloading speed between the
maximum and minimum on PC with specified IP address.
Setup Method:
-57www.zioncom.net
User’s Guide
Fill in specified IP address in the column, choose operating mode (maximum
Limit /Minimum Guarantee), and then fill value in forwarding and downloading
Bandwidth throughput, click “Apply”.
If delete current configuration, choose the value, click ”del”
Notes:
1.
If
Internet
throughput
configuration
changed,
current
Qos
configuration will be missing.
2.
Save current configuration before router power is off or reboot.
3.
For the management, prefer to static lease IP or using static IP
address on client’s PC.
6.8.3 Application QoS
Click “QoS” ->“Application QoS”,as follows:
-58www.zioncom.net
User’s Guide
Function :
QoS on application programme bandwidth throughput will be specified between
maximum or minimum value.
Setup Method:
Choose application programme to be specified, choose operation mode
(maximum Limit /Minimum Guarantee), specify the bandwidth throughput value, and
click “Apply”.
If want to delete current configuration, choose the column to be deleted, and
click “Apply”.
Notes:
1.
If
Internet
throughput
configuration
changed,
current
Qos
configuration will be missing.
2.
Save current configuration before router power is off or reboot .
3.
For the management, prefer to static lease IP or using static IP
address on client’s PC.
-59www.zioncom.net
User’s Guide
6.8.4 Port QoS
Click “QoS” ->“Port QoS”,as follows:
Function:
QoS on port bandwidth throughput will be specified between maximum or
minimum value.
Setup Method:
Choose port to be specified, choose operation mode (maximum Limit /Minimum
Guarantee), specify the bandwidth throughput value, and click “Apply”.
If want to delete current configuration, choose the column to be deleted, and
click “Apply ”.
Notes:
1.
If Internet throughput configuration changed, current Qos
configuration will be missing.
2.
Save current configuration before router power is off or reboot.
-60www.zioncom.net
User’s Guide
3.
For the management, prefer to static lease IP or using static IP
address on client’s PC.
6.9
NAT
6.9.1 Applications
Click “NAT”->”Applications”, as follows:
-61www.zioncom.net
User’s Guide
Some programs such as Internet network game, Video meeting, network phone
and so on need more than one connection. Because of Firewall some of the
programs can not work with simple NAT IP Router. But “Applications” can make
those programs work well with NAT IP Router.
Function:
This page is only for the special application programs that cannot work well with
Firewall or Proxy Server. If use these functions I, make the special application
programs work well with IP Router.
Setup Method:
Choose needed application grogram. Then fill the program’s IP address in
“Internal IP address”. Click “Apply” to make it effective.
Note:
1.
If you want to save all values after IP Router power off or restart, please
click “Save” button which is in right-above to save current values.
2.
If you want to choose option “Applications” , we recommend you to use
“Reserving IP” function or use static IP address in client computer in
order to manage it easily.
3.
The following is the list of all application port:
-62www.zioncom.net
User’s Guide
Application
BuddyBuddy
TCP 812, TCP 987
WinAmp Broadcasting
TCP 8000
GuruGuru
TCP 9292
TCP 9999
NetMeeting
TCP 1720
WinMX
TCP 6699
UDP 6257
Remote Desktop
TCP 3389
UDP 3389
Soribada2
UDP22321
Windows XP/2000
6.9.2
Port
Internal Server
Click “NAT”-> “Internal Server” as follows:
-63www.zioncom.net
User’s Guide
Because there is Firewall function in the IP Router, if computers in WAN try to
access servers in LAN through the IP Router, under default configuration the firewall
protection will not allow the access, then conflict occurs – at the same time IP Router
has to protect computers in LAN from WAN, at the other time it has to allow access
of valid users in WAN.
Here the IP Router provides you “Internal Server” function to solve the conflict.
Virtual Server provides one service port. All service requests to this port will be
relocated to the servers whose IP address has been appointed in LAN.
-64www.zioncom.net
User’s Guide
Function:
After been setup the IP Router can allow some services, such as DNS、SMTP、
POP3、HTTP、NEWS、FTP、Telnet、PPTP in LAN, to be open to Internet. Then users
from Internet can access servers in your LAN; Or by setting up DMZ Server you can
allow all application services and ports of one Server in your LAN to be open to
Internet.
Setup Method:
1.
Please confirm the LAN services which you wan to be open to Internet
according to the following list:
Protocol
DNS
SMTP
2.
Server
DNS (Domain Name Server)
SMTP (Simple Message Transfer
Protocol)
POP3
POP3(Post Office Protocol)
HTTP
Web Server
News
News Server
FTP
FTP File Transfer Server
Telnet
Telnet Server
PPTP
VPN (Virtual Private Network)
Choose the Server which you want to be open to Internet, then input Server
IP address. Click “Apply” button to make current setup valid. Note: All
open protocol port should be standard port, otherwise IP Router can not
transfer the data package from the invalid port which you have configured;
-65www.zioncom.net
User’s Guide
You can change external port number. But other users who want to access
the services which you have setup have to setup the port number before
successful access.
3.
If you want to setup “DMZ Host” please choose “DMZ ” option, then input
the internal Server’s IP address which you want to be open to Internet. IP
Router will transfer all received data packages except those which have
been setup in “Internal Server” to DMZ Server, and will allow the unlimited
dual communication between DMZ Server and outside Internet. If you are
using a new network application but IP Router can not transfer data
package without knowing the Port of this application, then you can setup all
DMZ ports to be open. After DMZ service being effective, firewall protection
of this computer will be invalid, please notice the safety.
NOTE:
1.
If you want to save all values after IP Router power off or restart, please
click “Save” button which is in right-above to save current values.
2.
If you use “Internal Server”, we recommend you to use “Reserving IP”
function or use static IP address in client computer in order to manage it
easily.
-66www.zioncom.net
User’s Guide
6.9.3
Port Forwarding
Click “NAT”->”Port Forwarding” as follows:
Function:
By the Port Range which user has setup, “Port Forwarding” will be defined as
Service Port. All requests to this port will be transferred to the computer which
appointed with “Internal PC IP address”.
Setup Method:
Input port transfer details which you want to setup in “Rule Name”. Choose
“Protocol” and “External Port Range” which you want to setup. Then setup
“Internal PC IP Address” and Port Transfer Range. Click “Add” to apply current
configuration. If you want to delete rule, then choose the rule which you want to
delete, click “Delete”.
Rule Name: Port transfer details need to be added.
Protocol: Port transfer protocol. There are 2 choices: TCP and UDP.
-67www.zioncom.net
User’s Guide
External Port Range:Port Range which is open to outside.
Internal PC IP Address:IP address of the computer to which IP Router
will transfer data.
Internal Port Range:Internal PC Port Range.
Note:
1.If you want to save all values after IP Router power off or restart, please
click “Save” button which is in right-above to save current values.
2.If you use “Port Forwarding”, we recommend you to use “Reserving IP”
function or use static IP address in client computer in order to
manage it easily.
6.9.4
Port Trigger
Click “NAT”->”Port Trigger” as follows:
-68www.zioncom.net
User’s Guide
Function:
If application program is connected form forward ports. All in trigger ports will be
opened to prepare for connection.
Setup Method:
Key in the description which you setup the function on the trigger port, Setup the
protocol and range of the trigger port, then setup the protocol and range of the
forward port, Click “Add” Button and add the rule, If want to delete the current rule,
Please select the rule which you want to delete and click “Del” button.
Rule Name: The description of adding the trigger port.
Port Trigger: Setup the trigger port.
Protocol: Select the trigger port’s protocol (TCP / UDP)
Port Range:Trigger port’s range.
Port Forward: Setup the forward port
Protocol: Select the forward port’s protocol (TCP / UDP)
Port Range:Forward port’s range.
6.9.5
NAT ON/OFF
Click “NAT”->“NAT ON/OFF”,as follows:
Make this router be operated on the NAT Off mode,If this option is checked,
all features about NAT will be disabled automatically
-69www.zioncom.net
User’s Guide
6.10
Advanced Setup
6.10.1 Firewall
Click “Advanced”->”Firewall” as follows:
Function:
Blocking Dos:Blocking list from all attack, all default value of the options
mentioned above is ON.
-70www.zioncom.net
User’s Guide
Blocking ICMP (ping) from Internet: In order to setup Ping package from
Internet to which IP Router has no response. It is for the protection from
shock wave attack and other hacker detects.
Blocking ICMP (ping) from LAN to Internet: In order to setup Ping
package from LAN to which IP Router has no response. It is for the
protection from shock wave attack.
Connection Filtering::By setting up IP address Filter, data package from
source IP address to destination address can be accepted or dropped.
Setup Method:
1.
Choose Dos attack from which needed protected, then click “Apply”
button to effect current configuration. (Note: Current all options’ default
value is ON)
2.
Setup relative parameter of connection filter. Click Add to effect current
configuration. If you want to delete current rule, then choose the rule and
click “Delete” button.
Direction:Setup the orientation of connection filter. There are two
options: “WAN”->”LAN” and “LAN”->”WAN”.
Source IP Address:IP Router address of the computer which sends
the data.
Net Mask: Subnet Mask of the computer which sends the data. Such
as 255.255.255.0 will be 24.
Destination IP Address:IP Router address of the computer which
receives the data.
Net Mask: Subnet Mask of the computer which receives the data.
Such as 255.255.255.0 will be 24.
Protocol:Protocol support. There are four options: Any、TCP、UDP
and ICMP,Any refers to all protocols.
Destination Port:Protocol port of destination computer. If any, then it
cannot be setup.
-71www.zioncom.net
User’s Guide
Accept/Drop:Setup “Connection Filtering” to accept or drop data
package.
Note:
1.
If you want to save all values after IP Router power off or restart, please
click “Save” button which is in right-above to save current values.
2.
If you use “Connection Filter” , we recommend you to use “Reserving IP”
function or use static IP address in client computer in order to manage it
easily.
6.10.2 DDNS
Click “Advanced”->”DDNS” as follows:
With Internet connections ways such as ADSL or Cable Modem, normally ISP
-72www.zioncom.net
User’s Guide
will allocate a dynamic IP address. Dynamic domain name service is a method of
keeping a domain name linked to dynamic IP address gets from ISP. But dynamic
domain name service depends on dynamic domain name service system. This
function can allow you to use registered dynamic domain name service no matter
how IP address changes.
Before use DDNS, an account provided by DDNS provider is needed.
Choose Dynamic DNS to be Stat, input valid “User ID” and “Password” that
got from DDNS provider. Fill your registered domain name in “Host Name”. Click
“Apply” button to effect current configuration.
DDNS Status:Display current DDNS status. “Started” or “Stopped”.
DynDNS Operation:DDNS “Start/Stop”。
User ID:The valid ID which you get from DDNS provider.
Password:The valid password which you get from DDNS provider.
Host Name:The valid domain name which you get from DDNS provider.。
-73www.zioncom.net
User’s Guide
6.10.3 WOL
Click “Advanced ”->”WOL”:
Function:
This function allows the wake-up signal from LAN or remote equipment to connect
to IP Router’s Internal network, and supports network wake-up computers.
Setup Method:
1.
If you want to send network wake-up signal to special client computer,
please input the computer’s name and LAN Card’s MAC address. Then
click “Add” button to add new rule.
2.
After setup, click “Wake-up PC” button to send network waken-up signal
to the computer which you want to wake up.
3.
If you want to delete current rule, please choose rule then click “Delete”
button.
-74www.zioncom.net
User’s Guide
6.10.4 URL Filter
Click “Advanced ”->”URL Filter” as follows:
Function:
In order to control the web stations which can be accessed by the computers in
LAN, you can use “URL Filter” function by PC’s IP or MAC address to appoint the
web stations which can be allowed to access or not.
Setup Method:
1.
Click “start” button to start URL Filter function.
2.
Input the IP address or MAC address which you want o filter in “IP Address”.
Input the web station address which you want to filter in “Input String”. For
example, if you want to forbid users to access “www.xxx.com”, you may input
-75www.zioncom.net
User’s Guide
“www.xxx.com” in “Input String”.
3.
Click “Add” button to effect current configuration.
4.
If you want to delete current rule, please click “Delete” button follow with the
rule.
Status:URL filter current status. “Started ” or “Stoped”.
Operation:URL setup “Start” and “Stop” switch. Click “Start” button to
start “URL Filter”, click “Stop” button to forbid “URL Filter”.
IP Address:Setup all computers which you want to limit. Include IP address
and MAC address limit. Choose “All IP” to limit all computers in LAN; when
choose MAC address, the default MAC address is the MAC address of the IP
Router which you are accessing.
Input String:The web station URL or keyword which you want to limit the
access.
By inputting www.xxx.com to limit users to access www.xxx.com
By inputting web sites’ keywords, such as sex xxx (between is Blank) to
forbid users to access www.sex.com and www.xxx.com.
Note:
1.
If you want to save all values after IP Router power off or restart, please
click “save” button which is in right-above to save current values.
2.
If you use “URL Filter”, we recommend you to use “Reserving IP”
function or use static IP address in client computer in order to manage it
easily.
6.10.5 Remote Management
Click “Advanced”->”Remote Mgmt” as follows:
-76www.zioncom.net
User’s Guide
This page is to setup IP Router’s remote management and WEB management
ports. After start Remote Management, users can remote manage the IP Router by
“http://WAN port IP address: Your setup Port (between is colon)”; If you want to
start remote management, please setup “Management port” then click “Apply”.
Status:Display the status and management Port number of remote
management setup.。
Operation:IP Router remote management Start/Stop switch.
Management Port:Remote WEB management port number.
-77www.zioncom.net
User’s Guide
6.10.6 Scheduler
Click “Advanced”->”Scheduler” as follows:
Function:
This function can limit Internet access time of client computers in LAN. Then
client computers in LAN can not access Internet in special time, but in other time
the access can be allowed.
Setup Method:
1.
Setup the days which you want to limit or “Everyday”.
2.
Choose limited time period or “All Day”.
3.
Input the IP or MAC address of the computer which you want to limit or “All
IP”.
4.
Click “Add” button to effect current configuration.
5.
If you want to delete current rule, please click “Delete” button follows with
the rules.
-78www.zioncom.net
User’s Guide
Days To Block:The days you want to limit. From “Monday” to
“ Sunday” or “Everyday”.
Time Of Day To Block:The time you want to limit. “24 Hours” or “All
Day”.
Address To Block:The computers you want to limit. “IP /Mask” or
“Physical”, or “All IP”.
Note:
1.
If you want to save all values after IP Router power off or restart, please
2.
If you use “Scheduler”, we recommend you to use “Reserving IP”
click “save” button which is in right-above to save current values.
function or use static IP address in client computer in order to manage it
easily.
6.10.7 VPN Setup
Click “Advanced”->”VPN Setup” as follows:
-79www.zioncom.net
User’s Guide
Function:
This wireless router VPN server,allow 5 user to get in at same time.
Setup Method:
VPN(PPTP)setup:Check Apply button to open VPN server
VPN(PPTP)account:Type in VPN client Account and Password,also enter
account IP address then check add button
If want to delete current account, check the account and check delete button to
delete it.
Note:
If you want to save all values after IP Router power off or restart, please click
“save” button which is in right-above to save current values.
-80www.zioncom.net
User’s Guide
1 Appendix A
UTP Cable specification
Twisted pair Category-5 straight-through cable
Twisted pair Category-5 Cross over cable
Straight-through Cable
Cross over Cable
-81www.zioncom.net
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising