Primo 60 Manual - Juwel Aquarium

Primo 60 Manual - Juwel Aquarium
Instruction Manual
Primo 60
www.juwel-aquarium.com
Introduction
Thank you for choosing a JUWEL Aquarium product.
Our products represent over 40 years experience in the manufacturing of aquariums
and their acessories applying most modern production techniques bringing together
the JUWEL Aquarium system, which is both easy to use and simple to maintain.
Important:
Please read this instruction manual carefully and completely to make sure you
have received all components before setting up the aquarium.
Please observe the safety instructions and maintenance guidelines given in this
manual.
This instruction manual has been carefully prepared to provide you with accurate
and complete information. All efforts have been made to ensure that the
information given is correct. However, we cannot accept responsibility for
printing or other errors. Technical details are always approximate and are not
warranted characteristics and may be subject to change without notice.
Always unplug all immersed electrical equipment from mains before placing your
hands into the water.
Important:
The use of additional air stones or air lines is not necessary with the JUWEL
Aquariums. If an air stone is used, this should always be placed in the middle of
the aquarium. Capillary leaks resulting from the use of these items will not be
accepted as a fault with the aquarium.
Do not transport or move your aquarium while still containing water or sand.
Always take care not to damage the seals while maintaining your aquarium.
Do not use toxic substances to clean your aquarium.
Safety instructions:
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
Operation with the RC circuit breaker only, max. 30mA.
The power plugs of the electrical devices must not become moist. Connect the
power plugs to the power supply at such a height that the connection cable
forms a loop which would enable the water to drip down.
The operation of a NovoLux LED luminaire is permitted only with an original
JUWEL driver for safety reasons.
Use only original JUWEL NovoLux LED luminaires and LED drivers when replacing
them.
Install the NovoLux LED luminaire only on the designated JUWEL brackets or
hoods.
Never attempt to open the NovoLux LED.
Never repair the electrical cord. Always replace the entire NovoLux LED Luminaire
or the LED Driver in case of damage.
2
Setting up the Aquarium
We have produced your JUWEL Aquarium with the utmost care using most advanced
production techniques. Extra strong packaging has been used to prevent damage to
the aquarium. Please note however, that your aquarium has been transported and
handled several times prior to reaching its final destination. We recommend
therefore, that you test the aquarium for leaks in a suitable area (e.g. garage), by
filling it with water and checking it very carefully.
Having made your checks, you should select the most suitable and desirable position
for your aquarium. The position selected should have an even and level surface and
should be able to support the weight of the filled aquarium. In order to prevent
excessive algae growth, we recommend that you select a position that is not exposed
to direct daylight.
We strongly recommend that the appropriate JUWEL Aquarium cabinet is used. They
have a water-repellent surface and they have been made to match the dimensions and
to bear the weight of the filled aquarium. The cabinet must be positioned on a level
surface. The JUWEL Aquarium is built with a special bottom frame for security. The
aquarium should be placed directly onto the cabinet. DO NOT place any additional
support, e.g. polystyrene, under the aquarium since this is not necessary with our
aquariums.
Weight of the aquarium in kg filled with water:
64
Suggestion: JUWEL Backgrounds
Front
Back
Complete the look of your aquarium by fitting one of our stunning backgrounds.
JUWEL Poster Backgrounds:
Vibrant plants or realistic rock on all double sided posters.
JUWEL Rock or Root Backgrounds:
Three dimensional Rock or Root backgrounds that give depth to the aquarium.
JUWEL Structured Backgrounds:
Subtle Bark effect that enhances the view of the aquarium.
JUWEL aquarium silicone:
The Rock, the Root and the Structured backgrounds are fitted to the inside of the
aquarium using the JUWEL silicone prior to filling.
JUWEL Terrace
Attractive terrace modules matching the design of the backgrounds Cliff, Stone, Rock
and Root.
All backgrounds are readily available from your JUWEL retailer.
3
Setting up your JUWEL Aquarium
In order to set up the aquarium and to prepare it for its intended use, please follow
these steps:
1. Make up the appropriate cabinet.
2. Place the aquarium in its chosen location.
24 h
3. Assemble the JUWEL backgrounds if applicable.
4. Ensure that the filter system is set up according to the instructions as described in
this manual.
5. Place your substrate in the aquarium.
6. Plant the low plant species in the aquarium.
7. Fill the aquarium with water up to half its height and plant the high plants.
8. Fill the aquarium with water slowly to the fill line.
9. Connect the pump and the heater to the power supply.
10. Place the lighting system onto the aquarium and connect the power supply.
You can add a few fish (4-5) after only a few days since you will need some livestock
to start the filter maturation process. The filter can take between 6 and 8 weeks to
fully mature. Should you choose to add further livestock during this period, then this
should be a gradual process.
The JUWEL Bioflow ONE filter
The JUWEL filter Bioflow ONE is a highly effective biological filter system with
components that are harmonized among each other in an ideal manner.
Installing the filter in the aquarium makes hose connections unnecessary and prevents
leaks. The pump output is not negatively affected by hose couplings, intake tubes
etc.
The pump capacity is dimensioned in such a manner that the biological filtering is
ensured by a sufficient flow through the filter material in an ideal manner.
The construction of the filter system enables you to quickly access the individual pump
and filter medium components, facilitating comfortable operation while cleaning and
maintaining the filter system.
In addition to this, the JUWEL Bioflow ONE filter system offers the option of
integrating the heater (optionally available).
4
Commissioning of the JUWEL Bioflow ONE filter
You should make the filter ready for use before setting up the aquarium, but do not
yet connect the electrical components to the power supply.
The JUWEL Bioflow ONE filter is consists of:
- Pump
- Filter housing with slot for the heater (optionally available)
- 2 blue filter sponges - bioPlus fine ONE
- 4 suction cups
- O2 diffuser
Prior to initial use of the filter, open the filter housing and remove the filter sponges,
in order to rinse them out under running water.
Reinsert the filter sponges into the filter housing and close it.
Now, insert the suction cups into the designated openings of the filter housing and
attach the filter in the rear right corner of the aquarium.
Now, attach the O2 diffuser (with assembled air hose and controller) onto the pump
outlet of the pump.
The JUWEL Bioflow ONE filter is now operational.
The JUWEL Aquarium Filter System is a biological filter system. For it to work
effectively, bacteria cultures will need to grow inside the blue sponges. This process
can take up 6-8 weeks for the filter to fully mature. Consequently we recommend to
decorate and plant the aquarium and add just a few (3-5) hardy fish in order to help
the maturation process. Please test the water on a weekly basis to monitor the water
conditions and once the water is safe you can begin to add more fish.
Servicing and maintenance of the JUWEL Bioflow ONE filter
BioPlus fine ONE - Replace one of the blue filter sponges at an interval of approx. 3
months.
Important:
Always use original JUWEL Aquarium filter media to ensure the optimum
performance of your system.
Tip:
EasyFeed - automatic feeder
We offer you the EasyFeed automatic feeder matching all JUWEL aquariums.
It is available from specialist retailers as original JUWEL Aquarium accessory (item No.
89000).
5
JUWEL AquaHeat - Operation and maintenance of the heater
The JUWEL aquarium heater is an essential component of the JUWEL filter system. Its
positioning within the filter housing and consequently in the water stream facilitates
even warming of the water in the aquarium.
You control the temperature of the water via the adjusting knob in the heater head.
You may specify the temperature the heater is supposed to heat the water to in
accordance with your individual requirements. The centre position between "+" and "-"
corresponds to a water temperature of approximately 23 - 26 degrees Celsius or 74-78
degrees Fahrenheit depending on the ambient temperature.
Please note that depending on the starting temperature of the water in the aquarium,
it may take approx. 12 hours and longer until the heater has heated the water to the
desired temperature. After that, the heater will automatically keep the water at the
desired temperature and switch on or off, accordingly. You recognise the operation of
the heater via the red glow light.
We also recommend you to check the temperature of the water by means of a
thermometer at regular intervals. The heater does not require further care or
maintenance.
Recommendation:
The JUWEL automatic heater warms the water of your aquarium up to 28°C
depending on a nomal room temperature of 21°C. If you keep your aquarium in
rooms below this or your fish need a higher temperature, we recommend to
purchase a second heater.
Safety instructions:
Only connect the heater once the aquarium is filled with water at least to the
minimum water level of the heater.
Maximum operating depth 80 cm.
Never use the heater outside the aquarium.
Operate the heater indoors only.
Safety instructions:
Always unplug the heater and allow it to cool before removing it from the filter.
Never attempt to open or repair the heater. Any signs of damage or malfunction
and the heater should be replaced with an original JUWEL Aquarium heater.
Never repair the electrical cord or plug. In case of damage replace the complete
heater.
Once removed never place on a flammable surface.
Recommendation
JUWEL Digital Thermometer 2.0
To monitor the temperature we recommend the JUWEL Digital Thermometer (Part No.
85702). Available from your JUWEL Aquarium retailer.
6
Maintenance of the JUWEL Eccoflow 300 pump
The JUWEL Eccoflow pump should be checked and cleaned at regular intervals (at least
once a month).
Please proceed as follows to that end:
1. Disconnect all electrical devices that are operated inside the water from the power
grid.
2. Remove the O2 diffuser from the pump outlet.
3. Remove the pump from the filter.
4. Disconnect the adapter (C) from the motor (A), by turning it anti-clockwise.
5. Remove the impeller (B) and the axle with their rubber bearings from the motor.
6. Thoroughly clean all components.
It is necessary to remove the impeller from the chamber and remove deposits and dirt
from the chamber itself as well as the impeller. Using the cleaning brush included with
the pump for this purpose. Otherwise the functionality of the pump will be impaired.
Also check the impeller for damage and possible signs of wear of the magnet.
7. After that, please reinstall the pump in reverse order in the filter. Before you
reconnect the devices that are operated in the water to the power supply.
Recommendation:
We recommend that you replace the parts subjected to wear and tear, e.g. the
impeller, axle and the rubber axle holders, adapter, at intervals of approx. 12 months
in order to ensure the optimum function and operating quietness of the pump. Inquire
at your specialist retailer for assistance.
Safety instructions:
Never operate the power head out of water.
Always unplug the power head from the power supply before removing it from the
filter.
The power head is intended for indoor use and for use in fluids up to 35°C.
Never repair the electrical cord or plug. In case of damage replace the complete
power head.
1
The lighting system JUWEL PrimoLux
2
3
The JUWEL PrimoLux lighting system enables you to achieve best lighting conditions
for your aquarium in an energy efficient way. It allows you furthermore to access the
aquarium under full lighting conditions.
The lighting system consists of
- hood (1)
PrimoLux 60/70
- JUWEL NovoLux LED with transformers (2)
2
- Operating flap/s (3) for food and water care products etc.
3
1
PrimoLux 110
7
Installation of the lighting system JUWEL PrimoLux
Position the enclosed brackets onto the socket provided for of the hood according to
the
illustration and screw them tight.
Now insert the NovoLux LED into the brackets.
Check that no sand or gravel is on the top edge of the aquarium and place the hood
onto the aquarium.
Then assemble the operating flap and connect the lighting system PrimoLux to the
power supply.
Tip:
The lighting system PrimoLux offers you the option to use additional NovoLux LEDs to
enhance the illumination or achieve special colour effects in the aquarium. Further
information will be available from your retailer or on our website www.juwel-aquarium.
com.
Maintenance and care JUWEL PrimoLux
The lighting system PrimoLux requires very little maintenance.
We recommend cleaning it with a soft towel and mild detergent as required.
Always disconnect the light from the power supply when carrying out maintenance
work.
8
Proper disposal (electrical waste)
The labelling on the product or on the accompanying literature declares that it
must not be disposed of, at the end of its service life, together with household
rubbish. Please dispose of this equipment separately from other waste, to protect
the environment or public health from damage by unregulated waste disposal.
Recycle the equipment and support the sustained recycling of material resources.
Private users should contact the dealer who sold them the product or the
responsible authorities, for a demonstration on how to recycle the equipment in
an environmentally friendly way.
Guarantee
We guarantee the performance of the JUWEL-Aquarium product or its accessories to the
purchaser for a period of 24 months from the date of purchase according to the
following conditions:
§ 1 Extent of the guarantee
(1) This guarantee extends to the JUWEL-Aquarium product and its components
excluding items subject to wear and tear such as light tubes and filter media. It is
limited to the product as such and does not cover damage to other property and/or
individuals. In addition, the provisions of the product liability law apply. These
provisions are not limited by the aforementioned arrangement.
(2) It is the prerogative of JUWEL-Aquarium to decide whether the guarantee is
performed by means of repair or replacement. If neither repair nor replacement can
ensure the performance of the JUWEL-Aquarium product the purchaser is entitled to
demand a reduction in price or to return the product against repayment of the
purchase price.
§ 2 Guarantee period and settlement procedure
(1) The guarantee period begins on the day of the purchase of the product from the
retailer. Claims under this guarantee will not be honoured, if
(a) the damage is caused as a result of improper use or maintenance or nonobservance of the instructions given in this manual
(b) the product or its components have been maintained by persons or companies not
authorised by the manufacturer to do so
(c) the product or its components have been damaged by mechanical means of
whatsoever kind, in particular broken glass
(2) All claims under this guarantee have to be notified to the retailer, from whom the
aquarium has been purchased without delay, however, not longer than 2 weeks from
the day of first occurrence of defects. Rights under the consumer protection laws will
remain unaffected.
(3) Guarantee claims will only be accepted if the validity of the claim is supported by
evidence of purchase of the JUWEL-Aquarium product.
This declaration of guarantee is a translation only. In case of doubts the original
German language version prevails.
We reserve the right to make technical alterations.
© JUWEL AQUARIUM
® JUWEL, Trigon, Vision, Rekord, Rio, Lido, Vio, Primo, Korall, MonoLux, DuoLux,
MultiLux, KoralLux, Violux, NovoLux, PrimoLux, SeaSkim, AquaHeat, EasyFeed, HighLite, Warm-Lite, Colour-Lite, Day-Lite, Juwel Twin-Lite, HiFlex, Juwel Eccoflow,
Bioflow, Cirax, Nitrax, Phorax, Carbax, BioPad, BioCarb, BioPlus, OxyPlus, Silexo,
Conexo.
JUWEL AQUARIUM GMBH & CO. KG
Karl-Göx-Straße 1 27356 Rotenburg/Wümme . GERMANY
Telefon +49(0)42 61/93 79-32
Telefax +49(0)42 61/93 79-856
Service-Mail service@juwel-aquarium.de
JUWEL AQUARIUM UK Branch
Gateway 11 Business Park
Penfold Drive, Wymondham Norfolk NR18 0WZ
Tel.: 01953 606 363 Fax: 01953 603 839
E-Mail: info@juwel-aquarium.co.uk
Service-Mail: info@juwel-aquarium.co.uk
9
Aquarien-Pass
PRIMO 60 - PrimoLux 60
Artikel
Bestell-Nr.
36360
36362 only UK
36263 only AU
36460
36462 only GB
36463 only AU
49260
49262 only GB
49263 only AU
JUWEL FILTER BIOFLOW ONE
Artikel
300
500
Bestell-Nr.
600
1000 1500
85092
85600
85800 only GB
85850 only AU
85751
85761 only GB
85771 only AU
88021
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising