monster superclean floor steamer (ez2)

monster superclean floor steamer (ez2)
MONSTER
SUPERCLEAN FLOOR STEAMER (EZ2)
INSTRUCTION MANUAL
Model #: EZ2 AUS, NZ
SAVE THESE INSTRUCTIONS
I M PO R TAN T SAF E
2
When using an electrical appliance, basic safety precautions
should always be observed, including the following:
Read all instructions before using this appliance.
WARNING:
To reduce the risk of fire, electrical shock, or injury:
1. This appliance is authorized for household/residential use only.
2. Do not charge or use outdoors or on wet surfaces. Do not immerse the floor
steamer in water or other liquids.
3. Do not allow to be used as a toy. Close attention is necessary when used by or
near children. Do not leave Steamer unattended. Always unplug unit when not
in use.
4. Use only as described and for the uses described in this manual. Use only
manufacturer’s approved and supplied parts and accessories. Use of other
accessories is not recommended and will void the warranty.
5. Always make sure the Handle Assembly is in the upright “off” position before
plugging in or unplugging. Keep cord away from heated surfaces (e.g.,
cooking surfaces), and sharp edges and corners.
6. Do not use if power cord or plug has been damaged, or if any part of
appliance has been dropped, damaged, left outdoors, or dropped in
water. Do not attempt to disassemble or repair appliance. Return it to the
manufacturer or an authorized service center for examination or repair.
7. Do not wrap cord too tightly around appliance. Never carry by the cord or
yank to disconnect from an outlet. To unplug, always grasp plug to remove
from outlet – do not pull on cord.
8. Do not handle cord or appliance with wet hands or without shoes on.
9. Look closely at Steamer and follow all labels and marking instructions.
10. Do not put any objects into openings. Do not use with any opening blocked.
11. Before filling with water or emptying, always place Handle Assembly in upright
“off” position, unplug Steamer and allow it to cool completely.
12. Turn the Boiler Cap slowly to open the boiler – this will allow any remaining
steam to escape gradually.
13. Use caution while emptying the appliance. Contact with hot water or steam
may cause burns.
14. Be sure Boiler Cap is (and remains) closed during use.
15. The Antibak Tank Cover should never be opened during use except to refill
while Steamer is stationary.
16. Never use cleaning solutions, perfumes, oils, Antibak or substances other than
tap or distilled/demineralized water in the Boiler. Use of any chemicals in Boiler
may damage Steamer and will automatically void the warranty.
17. Antibak should ONLY be used in the Antibak Tank (as detailed on pages 9 and 10).
18. When in use, never turn the appliance on its side. Do not direct steam at
people, animals, plants or electrical equipment (i.e, inside an oven).
19. Do not operate around flammable or combustible liquids such as gasoline, or in
areas where fumes may be present.
20. To reduce the likelihood of circuit overload, do not operate another high
wattage appliance on the same circuit. Plug in to a standard (220-240V,
50/600Hz) electrical outlet.
ATTENTION: This appliance is equipped with a 3-prong grounded power
cord. Insert only into a 3-prong grounded electrical outlet. Do not try to
remove the contacts of the grounded connection.
Safety Instructions
T
E
T Y I N S TR U C T I O N S
Euroflex relieves itself of any liability for damages that shall be the
result of improper use of the appliance, not in conformity with what’s
written in this instruction manual.
CAUTIONS
• Do not use your Floor Steamer without a Hard Surface Pad or Carpet Glide &
Pad attached to the system.
• Never leave your Floor Steamer in one spot on any surface for any period
of time. Always place on the Parking Pad and make sure the Floor Steamer
Handle Assembly is in the fully upright position when not in use - this turns the
Steamer Off.
• DO NOT disassemble Floor Steamer after assembly. This will cause damage.
*IMPORTANT*
Please read all of the
instructions for use and
Important Safety
Instructions carefully.
Remove and discard all
packaging materials
and keep them out
of the reach of children.
Save your back
No need to
press hard
The steamer
does the
work for you
WARNING
THIS FLOOR STEAMER WAS DESIGNED TO USE ANTIBAK CLEANING
SOLUTION ONLY! DO NOT USE ANY OTHER SOLUTION OR CLEANING
AGENT OR YOU WILL HARM THE STEAMER AND VOID THE WARRANTY.
Safety Instructions
SAVE THESE INSTRUCTIONS
21. Do not use extension cords or outlets with inadequate voltage.
22. Store appliance indoors in a cool, dry place.
23. If appliance is damaged, it must be repaired by the manufacturer or an
authorized service agent to avoid safety issues or risk of danger to the operator.
24. This appliance is not intended for use by persons (including
children) with
reduced physical, sensory or mental capabilities, or lack
of experience and
knowledge, unless they have been given supervision or
instruction concerning
use of appliance by a person responsible for
their safety.
25. Do not use Antibak sanitiser on carpets or rugs (or any other soft furnishings
such as mattresses or lounge). When using the Carpet Glide on carpets or rugs,
do not pull the trigger on the Handle to dispense Antibak. The steam coming
from the bottom of the Steamer is sufficient to refresh carpet or rugs.
26. Read and follow all important notices in this guide.
3
Product Feautres
One (1) Floor Steamer
1 - Cord Winder
2 - Handle
3 - Metal Extension Tube
4 - Measuring Cup (pre-marked)
5 - Filler Funnel
6 - Boiler Cap
7 - Steam Ready Indicator Light
(green)
8 - Power Indicator Light
(orange)
9 - Power Cord
10 - Front Steam Jets
11 - Antibak Tank Cover
12 - Hard Surface Floor Pad
13 - Carpet Floor Pad
14 - Parking Pad
15 - Carpet Glide
16 - Bottle of Antibak
17 - Antibak Tank Funnel
2
1
3
4
FILL UNIT WITH 2 CUPS WATER MAX
1 Cup
1/2 Cup
CLEAN BLAST
(Max)
5
Technical Data
6
11
7
8
9
Adapter Input: 220-240V~, 50/60Hz
Cord Length: 7 m
Power: 1200 watts
Boiler: Stainless Steel
Boiler Capacity: 0.6 lt
Pressure: 3.5 bars
15
10
16
12
13
14
D
G
RK
IN
PA
PA
17
4
Product Features
Assembly of Parts & Preparation of Steamer
Make sure all parts are in the box (see pg 4).
IMPORTANT: FOLLOW THESE INSTRUCTIONS CAREFULLY!
A. Assemble Handle
Before Use
1
After removing Handle Assembly from carton:
• Pull Extension Tube apart (shown below).
Pull apart Extension Tube

• Extend Tube to the
“Lock - I” position.

LOCK

K!
CLIC
• Snap connector down. When a “click” is heard, the Tube is locked in position.
“Maximum Extension” Position
*IMPORTANT*
Frontal steam can only be generated when Extension Tube is in the
“Maximum Extension” position. BE SURE EXTENSION TUBE IS FULLY
EXTENDED AND LOCKED IN PLACE FOR OPTIMAL STEAM OPERATION.
Before Use
5
Before Use
B. Attach Handle to Steamer
• Before starting, remove the self-tapping screw from the bottom
of Extension Tube.
• Insert the Handle Assembly into the Floor Steamer Base. Align
Arrow on Handle with Arrow on Base (as shown in Fig. A).
• Once inserted, twist Handle Assembly 90° clockwise (as shown
in Fig. B). Be sure Arrow on the Handle is aligned with Line/Lock
Icon on Base.
Fig. B
Fig. A
90°
Front View
Side View
Fig. C
• Align the Handle Assembly
screw hole with the opening
in the steamer housing.
Secure the Handle assembly
with self-tapping screw
which was removed from
bottom of Extension Tube
(as shown in Fig. C).
6
Before Use
Affix either the Hard Surface Floor Pad or Carpet Glide with
Carpet Pad to your Floor Steamer.
WARNING: To prevent floor damage, ALWAYS attach either the
HARD SURFACE FLOOR PAD or the CARPET GLIDE ACCESSORY
with CARPET PAD when using your Floor Steamer. NEVER use
without either of these attachments affixed to the machine.
Before Use
C. Attach Hard Surface Floor or Carpet Pad to Steamer
ATTACHING HARD SURFACE FLOOR PAD
Place Floor Pad face down on the floor, with
white hook and loop strips facing up. Hold
Floor Steamer about 2” above Pad and
gently place Floor Steamer onto the Pad.
Firmly press down to assure Pad is securely
adhered to the Floor Steamer.
ATTACHING CARPET GLIDE WITH CARPET PAD
Place Carpet Glide face up on floor. Center
and place Carpet Pad on top of Carpet
Glide. Hold Floor Steamer over the Carpet
Glide and gently lower the Steamer on to
the Glide. Make sure the 4 clips on Glide are
around the outside of the Steamer Base, and
then, using hands, attach 4 clips from the
Carpet Glide to the Steamer Base.
USE ON HARDWOOD FLOORS
For hardwood floors, use only on “sealed”
hardwood surfaces. Move Steamer forward
and backward while cleaning. Carefully
control the amount of steam used, as too
much water could cause damage.
IMPORTANT NOTE ABOUT LINOLEUM FLOORING
Steam can cause wax to be stripped from some varieties of linoleum
flooring causing damage. ALWAYS test a small, inconspicuous portion of
the floor BEFORE using steam to ensure that your linoleum floor does not
have this issue.
NOTE: See “Maintenance & Cleaning” for care and cleaning instructions for
Microfiber Pads.
Before Use
7
Before Use
D. Filling Boiler with Water
WARNINGS:
• Carefully read all instructions before removing Boiler Cap.
• Always unplug appliance before filling the Boiler.
*IMPORTANT*
Use ordinary tap water. Distilled or demineralized water is
recommended if tap water is too hard. DO NOT add detergents,
perfumes, oils, Antibak or other chemical substances to the Boiler.
The product warranty will be null and void if anything other than
water is added to the Boiler.
Follow these instructions to avoid overfilling
the Boiler.
• Be sure appliance is unplugged from the
electrical power outlet, and has cooled for
at least 5 minutes before filling with water.
• Make sure Handle Assembly is in the
upright “off” position. Remove Boiler Cap
by turning it counterclockwise.
200 ml
100 ml
ANTIBAK
(Max)
• Pour in 600 mls of water using
the Measuring Cup and Filler
Funnel provided – fill cup to the
“200 ml” marking three times.
Be careful not to overfill the
Boiler. Please note that excess
200
ml
100
ml
T
AN ax
(M
water will be flushed out during
use if the Boiler is overfilled,
resulting in wet floors.
• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – finger
tightening is sufficient to lock the steam in the Boiler.
If using cold water, heating time is about 3-5 minutes. If using warm
water, heating time is reduced.
*IMPORTANT*
Do not overfill the Boiler as excess water will be flushed out of the Boiler
before dry steam will emit. If re-filling the Boiler while Steamer has
been in use, be sure to allow Steamer to cool for at least 5 minutes and
loosen Boiler Cap slowly to allow any excess steam to escape before
completely removing Cap. (See step 2D, “Refilling Boiler During Use” for
detailed instructions.)
8
Before Use
This Monster Superclean Floor Steamer (EZ2) is equipped with a unique
on-demand option designed to sanitize your non-porous hard floor
surfaces (sealed wood, tile, marble, granite, linoleoum, etc.).
Included in this package is a 200 ml bottle of “Antibak”, a special
sanitizing agent that will quickly kill up to 99.9% of germs and bacteria.
Before Use
E. The Antibak Sanitizing System
The Antibak continues to work after it’s used, by killing bacterial spores
for up to 7 days following use. Be sure to use as directed.
A
Adding Antibak Sanitiser
• Push Antibak Tank Cover in the upward
direction (as shown in “A”) to reveal opening.
• Insert the small Antibak Tank Funnel in the
Antibak Tank.
• Use provided Measuring Cup to fill the Antibak
Tank (Figs. “B” and “C”). Pour Antibak into
Measuring Cup up to the “Antibak (Max)”
marking. We recommend tilting the Steamer
back when filling the Antibak Tank. Be careful
not to overfill.
REMEMBER: YOU CAN FILL THE ANTIBAK TANK WHEN
THE STEAMER IS ON AND HOT. BUT NEVER FILL THE
BOILER TANK WHILE THE STEAMER IS HOT!
200 ml
100 ml
ANTIBAK
(Max)
B
C
• Remove the small Antibak Tank Funnel from the
Antibak Tank.
D
• Close the Antibak Tank Cover “D”.
E
• You can now sanitize on
demand by pulling back the
Trigger on the Handle “E”.
Trigger
WARNING: Do not put Antibak sanitiser in the
Boiler. This will damage the Steamer and it will
void the warranty.
Continued on next page
Before Use
9
Before Use
E. The Sanitizing System (continued)
F
• The sanitiser is delivered to the surface only
through the front ports of the EZ2 Steamer “F”.
WARNING: Only use Antibak sanitiser in the
Antibak Tank located on the front of Steamer.
The EZ2 Steamer was designed to be used with
Antibak only. Any other cleaning solution used
may harm your Steamer and will void the warranty.
HINT: A little Antibak goes a long way – no need to soak your floor.
*IMPORTANT*
Using Your Floor Steamer
A. Using the Parking Pad
*IMPORTANT*
D
P
PA
The Parking Pad is provided to prevent floor
damage that can result from leaving a hot
steamer resting on the same spot for too
long. ALWAYS place Floor Steamer on the
Parking Pad when not in use, or while it is
cooling before storage.
You can use the Parking Pad if the Steamer
is warm or hot.
ING
10
2
AR
K
Using Your Floor Steamer
Do not use Antibak sanitiser on carpets or rugs (or any other soft furnishings
such as mattresses or lounge). When using the Carpet Glide on carpets or rugs,
do not pull the trigger on the Handle to dispense Antibak. The steam coming
from the bottom of the Steamer is sufficient to refresh carpet or rugs.
B. Starting the Appliance
• Be sure Boiler is filled with water, Boiler Cap is securely in place and
Antibak (if using) has been added to Antibak Tank.
• Insert the plug into a-3 prong grounded
electrical outlet (orange Power Indicator Light
will illuminate).
• Keep the Handle in the upright “off”
position. Wait until the (green) Steam Ready
Indicator Light illuminates.
• Once Boiler is filled and the green Steam Ready
Indicator Light illuminates, the Floor Steamer is
ready to clean.
PLEASE NOTE: The green Steam Ready Indicator
Light may turn on and off during
use. This is normal and not a fault.
Before Use & Using Your Floor Steamer
• To start cleaning using the
bottom steam ports, simply pull
the Handle downward. Always
use a Microfibre Pad.
You will find that your Floor
Steamer can easily clean most
hard floors using the underside
steam alone.
NOTE: Some water may be emitted when the Handle is first pulled down
after filling or when trigger on the Handle is pulled. This is normal.
To stop steam, simply return Handle to the upright position.
Using Your Floor Steamer
C. Using Floor Steamer
The Floor Steamer will stop producing steam when the
Boiler is empty. When this happens, refill with water
according to the instructions (see step 2D, “Refilling Boiler
During Use”).
To Use the Sanitizing System
The Monster Superclean Steamer will
sanitize non-porous hard floor
surfaces by using a sanitizing agent
called Antibak. The Antibak will
also keep floors sanitized by stopping
the growth of bacterial spores for 7
days after use.
To sanitise your floors using Antibak,
follow the filling instructions on page
9 of this manual.
To release the Antibak onto the floor,
pull the trigger on the Handle. The
Antibak will mix into the steam as it exits from the 4 front steam jets. Run the
steamer up and down on the floor to spread the Antibak.
A small amount of Antibak goes a long way. One pull of the trigger will release
enough Antibak to cover an area of 1 meter by 1 meter. The Antibak sanitiser
that is mixed with the steam coming from the front jets will get under furniture
and cabinets and disinfect to a distance of 30 cm.
Refill the Antibak Tank as needed. Once the Antibak runs out, replacement
bottles can be purchased from the appliance retailer who sold you the Monster
Superclean Floor Steamer.
REMINDER: If Floor or Carpet Pad become too wet or too
dirty, replace with a clean, dry Pad and continue cleaning.
*IMPORTANT*
Do not use Antibak sanitiser on carpets or rugs (or any other soft furnishings
such as mattresses or lounge). When using the Carpet Glide on carpets or rugs,
do not pull the trigger on the Handle to dispense Antibak. The steam coming
from the bottom of the Steamer is sufficient to refresh carpet or rugs.
Using Your Floor Steamer
11
Using Your Floor Steamer
D. Refilling Boiler During Use
When the Floor Steamer has run out of water, there will be no more
steam coming out of the unit. At this stage it is time to refill the Boiler.
Follow the refilling instructions below.
*IMPORTANT*
The Floor Steamer has a Boiler that should not be overfilled. To avoid the
potential for overfilling, only refill the Boiler when it is completely run out of
water and only add 600ml. Always follow the practice of using the Floor Steamer
until it has run out of water and then refill 600ml only.
If floor cleaning is completed and water remains in the Boiler, the Floor Steamer
can be stored with the remaining water in the Boiler, there will be no harm done
to the unit. At the next cleaning session simply heat up the unit and use the
water already in the Boiler, then refill when empty.
Or alternatively at the next cleaning session, open the Boiler Cap when the unit
is still cold and pour out the water and then refill (if this alternative method is
used, it is recommended that only 500ml of water is added, because the unit
will not completely drain when the water is poured out from the Boiler).
WARNING: Let Steamer cool 5 minutes before opening Boiler Cap.
Use care when opening Boiler Cap as it may still be hot and steam
may escape, causing burns. If Boiler is still hot, water may spurt out
during refilling which can also cause burns.
• Unplug the appliance from the electrical power outlet. This will stop
the Steamer from continuing to heat up.
• Once unplugged from the power outlet, place Handle in the “On”
position to release any residual steam and pressure from the Boiler.
• After all steam and pressure has been expressed from the Steamer,
return the Handle to the upright “Off” position.
• Slowly turn Boiler Cap counterclockwise. This will allow remaining
steam to escape.
• Be sure Steamer has cooled 5 minutes before refilling with water.
The product warranty will be null and void if
anything other than water is added to the Boiler.
• Pour in 600 mls of water using the Measuring Cup
and Filler Funnel provided – fill the Measuring
Cup to the 200 ml marking 3 times. Be careful
not to overfill the Boiler.
• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – finger
tightening is sufficient to lock the steam in
the Boiler.
• Insert plug into 3-prong electrical outlet. Wait for
green Steam Ready Indicator Light to turn on. Steamer is ready to use
once again.
200
ml
100
12
Using Your Floor Steamer
ml
T
AN ax
(M
• Always use ordinary tap water.
• If tap water is too hard, use distilled or demineralized water to
avoid the risk of mineral deposits and sediment from forming.
• Do not add detergents, perfumes, oils or other chemical
substances to the Boiler or Antibak Tank. This will damage the
Steamer and void the warranty.
• The green Steam Ready Indicator Light may turn on and off during
use. This is normal and not a fault.
• Only use Antibak sanitizer in the front Antibak Tank.
*IMPORTANT*
Do not overfill the Boiler as excess water will be flushed out of the
Boiler before dry steam will emit.
Cleaning the Floor Steamer
We recommend you periodically clean the Floor Steamer to prevent
the accumulation of calcium, mineral deposits and other sediment
caused by the use of tap water. After every 10-15 refills, fill the Boiler
three-quarters full of hot tap water, shake several times and empty
out the water into sink. Repeat several times to ensure that the Boiler
is flushed of any calcium or mineral deposits. Wipe the Steamer
base with a damp cloth and dry.
NEVER HOLD THE STEAMER UNDER THE TAP TO FILL. Use the Measuring
Cup and Funnel provided to fill the Boiler.
If distilled or demineralized water is regularly used in the Steamer,
cleaning of the Boiler can be done less frequently. In some areas tap
water is very hard, it is recommended that the Boiler is cleaned more
frequently if hard water is used.
The cleaning of the Boiler and Steamer is the sole responsibility of the
appliance owner. Calcium, mineral deposits and other sediment left
to build up in the Floor Steamer causing the Steamer to fail and/or the
steam pathways in the Steamer to block, is not covered by the product
warranty. Users must follow the cleaning instructions above.
Maintenance & Cleaning
3
Using Your Floor Steamer
REMINDERS
If the Steamer and Boiler are not cleaned according to the instructions above and the product fails and/or the steam pathways are
blocked, the appliance owner should send the product for servicing
by contacting the Customer Support Line.
The Monster Superclean Floor Steamer is intended for domestic
household use only. It is not intended for commercial use. Any use other
than for domestic household purposes will void the product warranty.
Using Your Floor Steamer & Maintenance & Cleaning
13
Maintenance & Cleaning
14
*IMPORTANT*
Do not add detergents, perfumes, oils, or other chemicals to the Boiler.
The product warranty will be null and void if anything other than water is
added to the Boiler.
Microfiber Pad Care & Cleaning
Your Microfiber Pads are designed for hundreds of uses. Clean Pads
regularly, either by hand (using mild soap and warm water) or in your
clothes washer on a delicate cycle, cool water. Never use fabric
softener or bleach. We recommend letting Pads air dry to maintain
maximum long term effectiveness.
Replacement pads are available at most retail outlets.
Microfiber washing instructions – ULTRA MICROFIBRE
HARD SURFACE FLOOR PAD
CARPET PAD
75% Polyester / 25% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric softener
80% Polyester / 20% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric softener
Maintenance & Cleaning
Possible Causes
Steam is not coming out of the
Solutions
Improper Handle assembly.
Steam Nozzles.
Call Customer Service to receive instructions
to correct the problem.
The Hard Surface Floor Pad
is not adhering to Steamer.
Not enough pressure was
applied when attaching Pad.
Position Steamer about 2” above Pad and
FIRMLY press it down onto the Pad.
Floor Pad requires replacing due to age of the Floor Pad.
Replacement Floor Pads can be purchased at
most electrical appliance reatail outlets.
The Cleaning Pads are getting
Boiler is overfilled.
soaked (too wet). Why?
Let Steamer run until excess water ceases.
-OR- Remove some water from Boiler once
the Boiler has cooled down completely.
Wait for green “Steam Ready Indicator Light”
to illuminate.
Green “Steam Ready Indicator
Light” is not illuminated.
The steam seems to be
Front Steam Jets are being
making my floor too wet.
used too frequently.
Only use Front Steam Jets in short bursts for
cleaning tougher stains or to clean hard to
reach areas.
Antibak Sanitizer Trigger is
being used too often.
Pull the Trigger less frequently, use more
sparingly.
The Cleaning Pad is too wet
(saturated with moisture)
Replace the wet Pad with a dry, clean Pad
and continue cleaning.
The Antibak is running out
quickly.
Trigger is being used too
frequently.
Pull Trigger less frequently and use Antibak
more sparingly.
Troubleshooting
Issues
IMPORTANT QUESTION:
Q: Do I always need to use a Microfiber Pad when cleaning with my
Steamer?
A. YES! It is critically important to ALWAYS use your Microfiber Pads. The
Floor Steamer should NEVER be used without either a Hard Surface
Floor Pad or Carpet Glide with Carpet Pad.
Troubleshooting
15
Customer Support
Customers needing assistance with their Monster Superclean Floor Steamer can call
the Customer Support Line on the phone numbers listed below. Customers should
also call the Customer Support Line if they require product warranty repair or postwarranty product servicing. Our friendly Customer Service Team can assist you to
get the best cleaning results from your Floor Steamer, they are full of helpful steam
cleaning tips, too.
Monster Customer Support Line
AUSTRALIA 1800 663 866
NEW ZEALAND 0800 666 783
EUROFLEX Australia Pty Ltd
8 Success Way
WANGARA WA 6065
AUSTRALIA
TEL: 08 9302 2526
Email: admin@euroflex.com.au
Website: www.euroflex.com.au
EUROFLEX New Zealand Ltd
PO BOX 305 650
Triton Plaza
North Shore 0757
NEW ZEALAND
TEL: 0800 666 783
Email: admin@euroflex.com.au
Website: www.euroflex.com.au
EUROFLEX SRL
Via dei Colli, 153
31058 Susegana (TV)
ITALY
Tel: +39 0438 661711
Email: euroflex@euroflex.tv
Website: www.euroflex.tv
Patent Pending
EZ2 (Australia/NZ) 9/25/14
EFLX-058 AB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising