DO Guide: TT-100_Series - AV-iQ

DO Guide: TT-100_Series - AV-iQ
DO GUIDE
DO Check the Box
QUANTITY
TT-100 Series
Crestron Connect It™ Cable Caddy
DO Install the Device
The TT-100 Series is designed for installation into a conference table.
The required thickness of the table is 1/2 inch (13 mm) to 1-1/4 inches
(32 mm).
5.Using the included Allen wrench, tighten the three setscrews (included
with the locking ring) to secure the locking ring to the bottom surface
of the table.
PRODUCT
COLOR
PART NUMBER
1
Cable, USB 2.0, A - Mini B, 6' 6" (2 m)
Black
2025146
1
Cable, USB 2.0, B - Mini A, 6' 6" (2 m)
Black
2038104
1
Connector, 4-Pin
2003576
1
Tool, 3/32" Allen Wrench
2036829
TT-100-B-T, TT-101-B-T, TT-110-B-T, and TT-111-B-T Only
Table
(Bottom View)
1
Cable Plate
Black
2036696
1
Locking Ring
Black
4519116
4
Screw, 6-32 x 1/4", Pan Head, Phillips
Black
2007215
TT-100-GRY-T, TT-101-GRY-T, TT-110-GRY-T, and TT-111-GRY-T Only
1
Cable Plate
Gray
2036697
1
Locking Ring
Gray
4519209
4
Screw, 6-32 x 1/4", Pan Head, Phillips
2007213
TT-101-B-T, TT-111-B-T, TT-101-GRY-T, and TT-111-GRY-T Only
TT-100
TT-110
Setscrews
(3)
NOTE: The TT-100 Series includes the TT-100, TT-101, TT-110, and TT-111.
The TT-101 consists of the TT-100 plus HDMI®, VGA, audio, and Ethernet
cables. The TT-111 consists of the TT-110 plus HDMI, VGA, audio, and
Ethernet cables. The TT-100, which provides a power outlet, is shown for
illustrative purposes throughout the remainder of this guide.
To install a TT device, do the following:
1.Properly protect the surface of the table.
2.Using a 4-inch (102 mm) hole saw (not included), drill a hole in the
appropriate location in the table.
3.With the TT device positioned so that the Crestron® logo faces the
user of the device, insert the body of the device into the hole.
1
Cable, Audio, Stereo, 1/8" Mini, 6' (1.83 m)
2037179
1
Cable, Ethernet, CAT5e, 7' (2.13 m)
2030114
1
Cable, HDMI, 6' (1.83 m)
2037173
1
Cable, VGA, 6' (1.83 m)
2037178
Not Included: 4-Inch (102 mm) Hole Saw; Phillips Screwdriver; and HDMI, VGA, Audio, and Ethernet Cables (Model Dependent)
6.Route the desired cables from the bottom of the TT device through
the cable opening. Up to four cables can be routed: one HDMI cable,
one VGA cable, one audio cable, and one Ethernet cable (all cables
supplied with the TT-101 and TT-111).
Cable
Opening
DO Connect the Device
Connect the device as required for the application.
NET/USB Port Connection
NET and USB ports are located on the bottom of a TT device.
NET
Port
USB
Port
7.Insert the cables into the appropriate holes in the included cable plate.
Use either the NET port or the USB port of a TT device to communicate
with a compatible DigitalMedia™ device:
Table
(User Side)
•• The NET port requires a Cresnet® control cable (not included) to
connect to a Crestron control system.
4.Twist the included locking ring onto the body of the TT device, leaving
a 1/8-inch (4 mm) gap between the locking ring and the bottom
surface of the table.
Table
1/8 in
(4 mm)
Locking Ring
HDMI
Audio/
Ethernet
Audio/
Ethernet
VGA
8.Seat the cable plate in the cable opening, and then attach the plate
using the four supplied Phillips pan head screws.
Phillips Pan Head
Screws (4)
24:
Y:
— NET — Z:
24 Y Z G G:
Power, 24 Vdc (Red)
Data (White)
Data (Blue)
Ground (Black)
NOTE: When the NET port of the TT device connects to a control
system, the TT device receives power via the NET port.
•• The USB port, which is a USB Type mini-AB port, requires the
included A to mini-B cable or B to mini-A cable to connect to the USB
port of a compatible DigitalMedia device.
NOTE: For proper USB functionality, the appropriate USB cable must
be connected to the TT device before the device is powered on.
The USB cable to be used depends on the USB type (Type A or
Type B) of the DigitalMedia device:
–– When an A to mini-B cable connects the USB port of a
DigitalMedia device to the USB port of a TT device, the TT device
receives power via the USB port. Compatible DigitalMedia
devices that connect to a TT device using an A to mini-B cable
include the DMPS3-4K-150-C, DM-MD8X1-4K-C, HD-MD8X1-4K,
and DM-TX-401-C. The DigitalMedia devices have USB Type A
host ports, which supply USB power.
–– When a B to mini-A cable connects the USB port of a
DigitalMedia device to the USB port of a TT device, the TT device
receives power via a connection to a Cresnet network or power
supply. A compatible DigitalMedia device that connects to a
TT device using a B to mini-A cable is the DM-TX-201-C.
The DM-TX-201-C has a USB Type B device port, which does
not supply USB power.
HDMI, VGA, Audio, and Ethernet Cable Connections
Connect HDMI, VGA, audio, and Ethernet cables as required for the
application:
•• Connect one end of the HDMI/VGA/audio cable to the appropriate
output port of an audio/video source (for example, a laptop) and the
other end of the cable to the corresponding input port of a compatible
DigitalMedia device.
•• Connect one end of the CAT5e Ethernet cable to a local network
device and the other end of the cable to the building network.
Cable
Connections
(Up to 4)
Power Pass-Through Outlet Connection
(TT-100 and TT-101 Only)
Connect the grounded ac power pass-through outlet and the power cord
(not shown) as required. The maximum load is 10 A @ 125 V, 50/60 Hz.
Power
Pass-Through
Outlet
DO Observe the Status Indicators
TT devices provide soft-touch capacitive Crestron Connect It™ buttons
with multicolored status indicators.
Crestron Connect It Buttons
COLOR
DESCRIPTION
Blue
Video source is not connected.
Blinking Green
Video is detected. The display is turning on.
Solid Green
Video appears on the display.
Slowly Pulsating Green Video is detected; however, video does not
appear on the display.
Five Red Blinks
No video is detected. The Connect It button is
touched. After five red blinks, the color reverts to
blue.
DO Learn More
Visit the website for additional information and the latest firmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the TT-110 and TT-111 have been tested and found to comply with specifications for CE marking.
The TT-100 Series is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•• Reorient or relocate the receiving antenna.
•• Increase the separation between the equipment and receiver.
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at http://www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, Crestron Connect It, and DigitalMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDMI and the HDMI Logo are either trademarks or registered trademarks of HDMI Licensing LLC in
the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron
is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
DO GUIDE
DOC. 7833A (2045092) 10.15
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising