WT-100 Quick Guide - Position Partners

WT-100 Quick Guide - Position Partners
*
WIRELESS LAN CONNECTION WITH IS AND FC-250
WT-100 Quick Guide
21303 90180
CONTENTS
1. WT-100........................................................................................................................................ 1
1.1 Channel .................................................................................................................................1
1.2 Communication range............................................................................................................1
1.3 Battery and Charger ..............................................................................................................1
2. HANDLING PRECAUTIONS..................................................................................................... 2
2.1 IP address setting ..................................................................................................................2
„ DHCP server......................................................................................................................2
3. HOW TO INPUT THE IP ADDRESS FOR IS........................................................................... 3
3.1 Turning on the power for wireless LAN..................................................................................3
3.2 IP adess setting for IS............................................................................................................4
3.3 Wireless information setting for IS .........................................................................................6
4. HOW TO SET FC-250 ............................................................................................................... 9
4.1 Setting the WLAN power of FC-250 to "ON" .........................................................................9
4.2 How to input the IP adess for FC-250..................................................................................12
5. HOW TO SET-UP THE TOPSURV (IS LIVE VIDEO MODE) ..............................................17
1. WT-100
1.1 Channel
1-11ch will be available. A default setting is "Auto", and a good condition channel will be selected
automatically.
1.2 Communication range
Approx. 300m. This is applied when IS is used. This can be changed depending on any obstacle
between the communicating instruments or ambient conditions.
1.3 Battery and Charger
BT-66Q (battery) is a standard accessory, but a charger is an optional accessory. The charger
included in the IS PKG can be used for WT-100.
1
2. Handling Precautions
2.1 IP address setting
WT-100 supports a DHCP server, but the use of Fixed IP address is recommended for IS
system.
„ DHCP server
When IS reconnects to WT-100, new IP address which is different from the previous IP address
may be assigned.
In this case, FC cannot recognize new IP address assigned to IS, then the system may not be
worked correctly.
2
3. How to input the IP address for IS
3.1 Turning on the power for wireless LAN
Turning on the power for wireless LAN.
Press the icon in the
following order:
[Start]-[Setting]-[Control
Panel]-[WLan Power].
Power for the wireless LAN will turn on.
3
3. HOW TO INPUT THE IP ADDRESS FOR IS
3.2 IP adess setting for IS
Set the IP address for IS.
As shown below, tap or select an item within the screen frame.
4
3. HOW TO INPUT THE IP ADDRESS FOR IS
Double-tap this item.
[1]
[2]
[3]
Set the address as shown
below.
[1] : Set the same IP
address as FC-250.
[2] : Set an IP address
different from the FC250 address.
[3] : Set the same subnet
mask as FC-250.
Now, the IP address is set.
5
3. HOW TO INPUT THE IP ADDRESS FOR IS
3.3 Wireless information setting for IS
Set the wireless information for IS.
Select "WT-100-W69999"
and tap [Connect].
"W69999" is the serial
number on the bottom
surface of WT-100.
6
3. HOW TO INPUT THE IP ADDRESS FOR IS
Place a check mark at the
upper left corner. Then, tap
[OK].
7
3. HOW TO INPUT THE IP ADDRESS FOR IS
The wireless information is set for IS. Now, IS is connected to WT-100.
8
4. HOW TO SET FC-250
4.1 Setting the WLAN power of FC-250 to "ON"
Set the W-LAN power of FC-250 to "ON".
9
4. HOW TO SET FC-250
10
4. HOW TO SET FC-250
Now, the WLAN power of FC-250 is set to "ON".
11
4. HOW TO SET FC-250
4.2 How to input the IP adess for FC-250
Set the IP address for FC-250.
Tap [Menu].
Tap [WLAN Settings].
12
4. HOW TO SET FC-250
13
4. HOW TO SET FC-250
14
4. HOW TO SET FC-250
15
4. HOW TO SET FC-250
[1]
[2]
[3]
Set the address as shown
below.
[1] : Set the same IP
address as IS.
[2] : Set an IP address
different from the IS
address.
[3] : Set the same subnet
mask as IS.
Now, FC-250 is connected to WT-100.
16
5. How to set-up the TopSURV (IS live video mode)
Set the application software.
17
5. HOW TO SET-UP THE TOPSURV (IS LIVE VIDEO MODE)
18
5. HOW TO SET-UP THE TOPSURV (IS LIVE VIDEO MODE)
19
5. HOW TO SET-UP THE TOPSURV (IS LIVE VIDEO MODE)
192 .168 .111 .101
Now, setting of the application software is finished.
20
Input the IP address, which
has been set for IS. Then,
tap [
].
*
http://www.topcon.co.jp
Please see the attached address list or the following website for contact addresses.
GLOBAL GATEWAY http://global.topcon.com/
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising