View 2012 Fit Fog Lights (Base Model)

View 2012 Fit Fog Lights (Base Model)
INSTALLATION
INSTRUCTIONS
Accessory
Application
FOG LIGHTS
P/N 08V31-TK6-100
2012 FIT
(BASE MODEL)
Publications No.
AII 45996
Issue Date
AUG 2011
PARTS LIST
Right fog light
Bracket (R)
Left fog light
Bracket (L)
Switch harness
Relay bracket
Fog light harness
Right cover
Bracket assembly (R)
Left cover
Bracket assembly (L)
Fog light switch
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
08V31-TK6-1000-91
1 of 14
Wire tie with clip
TOOLS AND SUPPLIES REQUIRED
10 mm Wrench
Diagonal cutters
KTC trim tool set (KTC ATP2014J)
Eye protection (face shield, safety goggles, etc.)
Drill
Relay
3 mm Drill bit
Hacksaw
Isopropyl alcohol
Shop towel
Flat-tip screwdriver
20A fuse
Phillips screwdriver
Ratchet
File
Fuse label
10 mm Socket
Cardboard or blanket
20 mm and 25 mm Hole saws
Pushpin
Duct tape
4
Step-screws
Illustration of the Fog Lights installed on the vehicle
20A FUSE
2
Washer-screws
16 Self-tapping screws
FOG
LIGHT
SWITCH
11 Wire ties
SWITCH
HARNESS
RIGHT
FOG
LIGHT
2 of 14
AII 45996 (1108)
FOG LIGHT
HARNESS
RELAY
LEFT FOG LIGHT
832030AS
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
•
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the audio
unit and navigation system (if equipped), then write
down the audio unit presets.
2.
Disconnect the negative cable from the battery.
3.
Remove the front bumper:
•
Remove the front grille cover (eight clips).
LONG
CLIP
Remove the five clips and the six self-tapping
screws from the bumper.
SELF-TAPPING
SCREW
SELF-TAPPING
SCREW
SHORT
CLIP
SELFTAPPING
SCREW
6 SHORT
CLIPS
•
LONG
CLIP
LONG
CLIP
SELFTAPPING
SCREW
SHORT
CLIP
Attach duct tape to the bumper in the area
shown.
GRILLE
COVER
HEADLIGHT
TAB
DUCT
TAPE
TAB
FRONT
BUMPER
DUCT
TAPE
•
With the help of an assistant, release the three
tabs between the fender and the bumper on
each side, and pull the bumper straight out to
release the four tabs along the bottom of the
headlight.
NOTE: If you try to remove the bumper without an
assistant, you may scratch the bumper around the
headlight area.
•
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
Place the front bumper on a blanket to prevent
damage.
3 of 14
Installing the Fog Lights
4.
8.
On the inside of the front bumper, locate the seven
preset marks. Using a pushpin, pierce the center of
each preset mark.
Locate the two remaining preset marks below the
cutout. Using a pushpin, pierce the center of the two
preset marks.
FRONT BUMPER (Inside)
MARK
(25 mm
HOLE SAW)
PUSHPIN
3mm
DRILL
BIT
MARK
PUSHPIN
(3 mm DRILL BIT)
DRILL
(20 mm hole saw)
9.
7 MARKS
5.
While wearing eye protection, drill each of the seven
pierced marks. First drill with a 3 mm drill bit, then
enlarge the holes using a 20 mm hole saw.
6.
Using a hacksaw, cut out the front bumper between
the 20 mm holes.
FRONT BUMPER (Inside)
While wearing eye protection, drill the two pierced
marks. First drill with a 3 mm drill bit, then enlarge the
holes using a 25 mm hole saw.
NOTE: The drilled holes will be larger than the preset
marks.
10. Locate the preset mark along the bottom of the front
bumper. Using a pushpin, pierce the center of the
preset mark.
Cut out.
(25 mm HOLE SAW)
(3 mm DRILL
BIT)
PUSHPIN
LINE
HACKSAW
7.
832002AS
FRONT BUMPER
(Inside.)
Remove any burrs from the edges of the cutout.
MARK
11. While wearing eye protection, drill the pierced mark.
First drill with a 3 mm drill bit, then enlarge the hole
using a 25 mm hole saw.
12. Remove any burrs from the drilled holes.
13. Repeat steps 4 thru 12 to drill and cut the bumper on
the right side.
4 of 14
AII 45996 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
14. Using one washer-screw and one step-screw, install
the bracket assembly (L) to the left fog light.
17. Install the left cover over the left fog light.
STEPSCREW
STEPSCREW
BRACKET
ASSEMBLY (L)
LEFT FOG LIGHT
BRACKET (L)
STEPSCREW
LEFT
COVER
FRONT
BUMPER
WASHER-SCREW
832005AS
BRACKET
ASSEMBLY (L)
18. Using four self-tapping screws, secure the left fog
light cover to the fog light bracket.
STEPSCREW
4 SELF-TAPPING
SCREWS
BRACKET (L)
LEFT COVER
15. Using one step-screw, install the bracket (L) to the
left fog light.
16. Using four self-tapping screws, secure the left fog
light assembly to the front bumper.
4 SELF-TAPPING
SCREWS
FRONT BUMPER
BRACKET
ASSEMBLY (L)
LEFT FOG LIGHT
ASSEMBLY
BRACKET (L)
19. Repeat steps 14 thru 18 to install the right fog light
and cover.
BRACKET
ASSEMBLY (L)
LEFT FOG LIGHT
ASSEMBLY
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
BRACKET (L)
AII 45996 (1108)
5 of 14
Routing the Fog Light Harness
24. Route the fog light harness downward. Secure the
1-pin connector to the vehicle harness using one
wire tie.
20. Turn the steering wheel all the way
counterclockwise.
21. At the right front wheel, remove the two clips and pull
the right front inner fender out to locate the vehicle
1-pin connector.
CLIP
1-PIN
CONNECTOR
VEHICLE
HARNESS
CLIP
(with screw)
WIRE
TIE
VEHICLE
HARNESS
FOG LIGHT
HARNESS
RIGHT FRONT
INNER FENDER
Pull out.
25. Secure the fog light harness to the vehicle harness
with two wire ties.
22. Remove the blue tape to free the vehicle 1-pin
connector from the vehicle harness.
View from the bottom
FRONT HOLE
Use this hole.
FOG LIGHT
HARNESS
(long end)
BLUE
TAPE
Remove.
REAR
HOLE
WIRE TIE
HARNESS CLIP
VEHICLE
HARNESS
VEHICLE 1-PIN
CONNECTOR
1-PIN CONNECTOR
FOG LIGHT HARNESS
23. Plug the fog light harness 1-pin connector into the
vehicle 1-pin connector.
6 of 14
FOG LIGHT HARNESS
(short end)
26. Route the long end of the fog light harness under the
bumper beam, and insert the harness clip into the
front hole in the bumper beam.
AII 45996 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
27. Route the long end of the fog light harness across
the front of the vehicle, and insert the two harness
clips into the front bumper beam.
29. Remove the vehicle ground bolt. Attach the fog light
harness ground to the vehicle ground and reinstall
the vehicle ground bolt.
FOG LIGHT HARNESS
VEHICLE HARNESS
HARNESS
CLIPS
FOG LIGHT HARNESS
(long end)
WIRE
TIE
REAR
HOLE
FRONT HOLE
Use this hole.
VEHICLE
GROUND BOLT
Top View
28. Route the fog light harness under the left bumper
beam, and insert the harness clip into the hole in the
bumper beam.
FOG LIGHT
HARNESS
FRONT HOLE
Use this hole.
FOG LIGHT
HARNESS
30. Secure the fog light harness to the vehicle harness
with one wire tie.
Bottom View
REAR
HOLE
HARNESS
CLIP
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
7 of 14
31. With the help of an assistant, move the front bumper
close to the vehicle. On each side, plug the fog light
harness 2-pin connector into the fog light, and insert
the harness clip into the hole in the fog light bracket
assembly. Reinstall the front bumper.
Routing the Switch Harness
33. Under the dash on the left side of the vehicle, turn
the knob of the driver’s dashboard under cover
counterclockwise. Remove the driver’s dashboard
under cover (one clip and two tabs).
FOG LIGHT
HARNESS
CLIP
FOG LIGHT
HARNESS
2-PIN
CONNECTOR
CLIP
BRACKET
ASSEMBLY
(R) (L)
DRIVER’S
DASHBOARD
UNDER COVER
2 TABS
KNOB
Turn.
34. Pull away the door seal from the driver’s kick panel,
then remove the driver’s kick panel (two clips and
two tabs).
RIGHT
FOG
LIGHT
DOOR SEAL
Pull away.
LEFT
FOG
LIGHT
FRONT
BUMPER
32. Reinstall the inner fender.
CLIP
TAB
8 of 14
AII 45996 (1108)
DRIVER’S KICK PANEL
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
35. Remove the fuse access panel (five tabs, two clips,
and two holders). If equipped, remove the ambient
light harness connector and slide off the wire tie with
clip.
AMBIENT LIGHT
HARNESS CONNECTOR
(If equipped)
WIRE TIE
WITH CLIP
(If equipped)
Slide off.
38. Remove the lower bolt from the hood release lever
bracket.
2 CLIPS
LOWER
BOLT
Reuse.
HOOD RELEASE LEVER
39. Attach the relay bracket to the hood release lever
bracket, and reinstall the lower bolt.
HOLDER
HOLDER
5 TABS
RELAY BRACKET
FUSE ACCESS PANEL
36. Locate the vehicle 2-pin connector blue-taped to the
vehicle harness. Remove the blue tape to free the
vehicle 2-pin connector.
AS
40. Install the relay into the switch harness relay block,
and slide the relay block onto the switch harness
relay bracket.
SWITCH HARNESS
RELAY
FUSE BOX
RELAY
BLOCK
BLUE
TAPE
Remove.
SWITCH HARNESS
2-PIN CONNECTOR
VEHICLE 2-PIN
CONNECTOR
RELAY BRACKET
RELAY BLOCK
832015AS
37. Plug the switch harness 2-pin connector to the
vehicle 2-pin connector.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
9 of 14
41. Using isopropyl alcohol on a shop towel, clean the
No. 4 area on the driver’s kick panel, then attach the
fuse label (20A option fuse, diagonal line) to the
cleaned area.
42. Insert the 20A fuse into the No. 4 position (the sixth
position from the bottom) of the fuse box.
NOTE: If a security system is installed, a 20A fuse is
already installed in the fuse box. There is no need to
install the fog light 20A fuse from the kit.
NOTE: If a security system is installed, the fuse label
is already attached to the No. 4 area. You do not
need to attach the label from the kit.
FUSE LABEL
(20A OPTION FUSE)
Attach to No.4.
Front View
FUSE
BOX
Clean No.4.
FUSE No.4
Insert into the
sixth position
from the bottom.
Plug in the switch harness
8-pin connector.
Front View
DRIVER’S KICK PANEL
20A FUSE
FUSE
BOX
8-PIN
CONNECTOR
SWITCH
HARNESS
43. Plug the switch harness 8-pin connector into the slot
shown above.
NOTE: If the vehicle is equipped with a security
system, remove the dummy connector from the
security system harness, and plug the fog light
harness into the security system harness.
10 of 14
AII 45996 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
44. Route the switch harness 5-pin connector out
through the dashboard opening.
47. Using one wire tie, secure the excess fog light
harness and connector to the vehicle harness.
DASHBOARD OPENING
WIRE
TIE
SWITCH
HARNESS
5-PIN
CONNECTOR
5 WIRE
TIES
VEHICLE
HARNESS
VEHICLE
HARNESS
SWITCH HARNESS
SWITCH HARNESS
45. Using five wire ties, secure the switch harness to the
vehicle harnesses in the areas shown.
If the vehicle is equipped with ambient lights, go
to step 49. If not, continue with step 46.
46. Unplug the vehicle 13-pin connector from the mirror
switch connector, and plug it into the switch harness
13-pin connector with urethane cushion. Plug the
other switch harness 13-pin connector into the mirror
switch 13-pin connector.
13-PIN
CONNECTOR
(with urethane cushion)
48. Go to step 51.
49. Unplug the vehicle 13-pin connector from the
ambient light harness, and plug it into the switch
harness 13-pin connector with urethane cushion.
Plug the other switch harness 13-pin connector into
the ambient light harness connector.
MIRROR
SWITCH
VEHICLE 13-PIN
CONNECTOR
AMBIENT
LIGHT
HARNESS
MIRROR
SWITCH
13-PIN CONNECTOR
(with urethane cushion)
SWITCH
HARNESS
13-PIN CONNECTOR
(with urethane cushion)
SWITCH
HARNESS
VEHICLE
13-PIN
CONNECTOR
13-PIN CONNECTOR
(with urethane cushion)
13-PIN
CONNECTOR
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
11 of 14
50. Secure the two 13-pin connectors to the ambient
light harness, using one wire tie for each connector.
53. Install one wire tie with clip to the switch harness in
the position shown.
5-PIN CONNECTOR
140 mm
(5.5 in.)
WIRE TIE
WITH CLIP
SWITCH
HARNESS
AMBIENT
LIGHT
HARNESS
WIRE
TIE
FOG LIGHT
SWITCH
13-PIN CONNECTOR
(with urethane cushion)
FUSE
ACCESS PANEL
(inside)
FOG LIGHT HARNESS
Installing the Fog Light Switch
51. Remove the left blank cover from the fuse access
panel.
FUSE
ACCESS
PANEL
FUSE
ACCESS
PANEL
(inside)
54. Plug the switch harness 5-pin connector to the fog
light switch.
55. Attach the wire tie with clip to the clip holder on the
inside of the fuse access panel.
56. Reinstall the fuse access panel and go to step 61.
AMBIENT
LIGHT SWITCH
(If equipped)
57. Using one wire tie, secure the switch harness to the
ambient light harness.
AMBIENT LIGHT
HARNESS
5-PIN
CONNECTOR
WIRE TIE
5-PIN
CONNECTOR
SWITCH
HARNESS
FOG
LIGHT
SWITCH
BLANK
COVER
52. Install the fog light switch into the fuse access panel.
If the vehicle is equipped with ambient lights, go
to step 57. If not, continue with step 53.
12 of 14
FUSE ACCESS PANEL
(inside)
AII 45996 (1108)
FUSE
AMBIENT ACCESS
FOG
PANEL
LIGHT
LIGHT
SWITCH SWITCH
832024BS
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
58. Plug the switch harness 5-pin connector and the
ambient light harness 5-pin connector to the fog light
switch and the ambient light switch.
59. Attach the wire tie with clip to the clip holder on the
inside of the fuse access panel.
Fog Light Aiming Adjustment
• Adjust the aim according to local laws and regulations.
• To adjust, turn the aiming adjustment screw in or out
until the correct aim is obtained.
60. Reinstall the fuse access panel.
61. Check that all wire harnesses are routed properly
and all connectors are plugged in.
62. Reinstall all removed parts.
63. Connect the negative cable to the battery and check
the operation of the fog lights.
64. Enter the anti-theft codes for the audio system and
the navigation system (if equipped).
65. Reset the clock on the vehicles without navigation.
USE AND CARE
How to Operate Fog Lights
• Turn the light switch to the “
low beam).
” position (headlights on
To lower.
• Press the fog light switch (indicator is on).
To raise.
Lower View
BULB REPLACEMENT
1.
Remove the self-tapping screw and the clip, and
then move the inner fender out of the way.
HEADLIGHT SWITCH
OFF
FOG LIGHT
SWITCH
INDICATOR
Low
High
OFF
-
-
-
-
ON
-
-
ON
-
NOTE: The fog light lenses can cloud when the outside
temperature is cold; this is normal and should go away in
warm weather.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45996 (1108)
SELFTAPPING
SCREW
CLIP
13 of 14
2.
Unplug the fog light connector.
4.
FOG
LIGHT
Install the new bulb into the fog light.
•
When replacing the fog light bulb, be careful not
to damage the lenses or the painted surface of
the bumper.
•
Use only a Honda Genuine halogen light bulb of
specified wattage.
Rating: 12V 55W H11 Halogen Light Bulb
P/N 33165-S5A-003
•
Do not touch the bulb. Oily or greasy substances
on the bulb can shorten its service life due to the
heat produced when the bulb is turned on. If the
bulb is accidentally touched, wipe it clean with a
soft cloth that has been dampened with a
denatured alcohol or a mild detergent solution.
•
When installing the new bulb, align the cutout on
the fog light with the tab on the new bulb and turn
the new bulb clockwise until it locks. If not
properly aligned, the fog light may blind
oncoming drivers.
BULB
CONNECTOR
3.
Remove the bulb by turning the bulb
counterclockwise.
AS
Turn the bulb
until it stops.
CONNECTOR
FOG
LIGHT
NEW
BULB
14 of 14
5.
Reinstall the removed parts. Check that the wire
harnesses are not pinched. Be sure to tighten the
clips securely.
6.
Check the operation of the fog light; adjust the aim if
necessary.
AII 45996 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising