SK 1000W说明书--141101--7504-0539-01.cdr
BALANCE CHARGER
DISCHARGER
ALL PURPOS E MU LTI-CH E M ISTRY
SkyRC Technology Co., Ltd. 2014
TABLE OF CONTENTS
INTRODUCTION
01
SPECIAL FEATURES
03
WARNING AND SAFETY NOTES
05
PROGRAM FLOW CHART
08
OPERATION
09
OPERATING PROGRAM
10
CHARGING PROGRAM
14
BATTERY MEMORY SET AND CALL OUT
15
SYSTEM SETTING
17
BATTERY METER
19
BATTERY RESISTANCE METER
20
WARNING AND ERROR MESSAGE
21
USING THE CHARGE CONTROL SOFTWARE “CHARGE MASTER”
22
SPECIFICATION
24
CONFORMITY DECLARATION
25
MAXIMUM CIRCUIT POWER CHART
26
COMMONLY USED TERMS
28
WARRANTY AND SERVICE
29
INTRODUCTION
Congratulations on your choice of SKYRC Ultimate 1000W Balance
Charger/Discharger. This unit is simple to use, but the operation of a
sophisticated charger such as SKYRC Ultimate 1000W does require some
knowledge on the part of the user. These operating instructions are designed
to ensure that you quickly become familiar with its functions. It is therefore
important that you read right through the Operating Instructions, Warning and
Safety Notes before you attempt to use your new charger for the first time.
We hope you have many years of pleasure and success with your new battery
charger.
SKYRC Ultimate 1000W features with high efficiency with synchronous
rectification technology. It also has some new features and functions. Users
could set the terminal voltage by themselves and connect it to PC for PC
control and firmware upgrade. What's more, users could also use it as
Lithium Battery Meter and Lithium Battery Internal Resistance Meter. There
are Automatic Charging Current Limit, Capacity Limit, Temperature
Threshold and Processing Time Limit which makes the charger safe to use.
Ultimate 1000W employs the circuit that features output power of 1000
watts. It can charge 20 cells of NiCd/NiMH or 8 series of Lithium batteries
with maximum current of 40A. Ultimate 1000W has an individual cell voltage
balancer, so it does not required any balancer separately when charging
Lithium batteries (LiPo/LiIon/LiFe) for voltage balancing.
Reliable/durable membrane button systems are using for charger controls.
The fan cooling system is so smart and efficiently. The fan speed is
controlled by internal temperature sensor.
Please BE SURE to read these INSTRUCTIONS, WARNING and SAFETY
NOTES before you use the charger for the first time.
It can be dangerous to mis-handle batteries and battery chargers, as there is
always a risk of batteries catching fire and exploding.
Ultimate 1000W
01 ·
INTRODUCTION
Please read this entire operating manual completely and attentively
before using this product, as it covers a wide range of information on
operating and safety. Or please do use this product in company with a
specialist!
Output
Display
Large 2x16 LCD for
Easy Reading
Balancing
Port
Temperature
Sensor Port
Batt Prog DEC/INC
/Stop
Button
Button
Start/Enter
Button
Cooling
Fan
USB Port for
1. PC Control &
Firmware Upgrade
2. Wi-Fi Module
Connection
DC INPUT 11-30V
· 02
Ultimate 1000W
SPECIAL FEATURES
Optimized Operating Software
Ultimate 1000W features the so-called AUTO function that set the feeding current during the
process of charging or discharging. Especially for lithium batteries, it can prevent the
overcharging which may lead to an explosion due to the user's fault. It can disconnect the
circuit automatically and alarm once detecting any malfunction. All the programs of this product
were controlled through two way linkage and communication, to achieve the maximum safety
and minimize the trouble. All the settings can be configured by users!
Battery Memory (Data Store/Load)
The charger can store up to 10 different charge/discharge profiles for your convenience. You
can keep the data pertaining to program setting of the battery of continuous charging or
discharging. Users can call out these data at any time without any special program setting.
Terminal Voltage Control(TVC)
The charger allows user to change the end voltage. (for expert user only)
PC Control Software “Charge Master”
The free “Charge Master” software gives you unparalleled ability to operate the charger through
the computer. You can monitor pack voltage, cell voltage and other data during the charging,
view charge date in real-time graphs. And you can initiate, control charging and update
firmware from “Charge Master”.
Smart Phone Control via Wi-Fi Module (both iOS and Android)
Finally, your charger gets its own apps. This charger can be controlled and operated by smart
phones via Wi-Fi module(option part SK-600075).
LiHV Mode Available
The additional LiHV mode is able to charge the new generation of LiPo batteries with an
end of charge voltage of 4.35 V.
Balance Port for Lithium Battery Charging
For some small batteries without main connector, you could use the battery socket to charge
and discharge the battery to storage status.
Internal Independent Lithium Battery Balancer
Ultimate 1000W employs an individual-cell-voltage balancer. It isn't necessary to connect an
external balancer for balance charging.
Balancing Individual Cells Battery Discharging
During the process of discharging, Ultimate 1000W can monitor and balance each cell of the
battery individually. Error message will be indicated and the process will be ended automatically
if the voltage of any single one cell is abnormal.
Adaptable to Various Type of Lithium Battery
Ultimate 1000W is adaptable to various types of lithium batteries, such as LiPo, LiIon and the
new LiFe and LiHV series of batteries.
Ultimate 1000W
03 ·
SPECIAL FEATURES
Fast and Storage Mode of Lithium Battery
Purposes to charge lithium battery varies, 'fast' charge reduce the duration of charging,
whereas 'store' state can control the final voltage of your battery, so as to store for a long time
and protect useful time of the battery.
Re-Peak Mode of NiMH/NiCd Battery
In re-peak charge mode, the charger can peak charge the battery once, twice or three times in
a row automatically. This is good for making certain the battery is fully charged.
Delta-peak Sensitivity for NiMH/NiCd
Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge termination program based
on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the
threshold, the process will be terminated automatically.
Cyclic Charging/Discharging
1 to 5 cyclic and continuous process of charge > discharge or discharge > charge is operable
for battery refreshing and balancing to stimulate the battery's activity.
Automatic Charging Current Limit
You can set up the upper limit of the charging current when charging your NiMH or NiCd
battery, it is useful for the NiMH battery of low impedance and capacity in the 'AUTO' charging
mode.
LiPo Battery Meter
The user can check battery's total voltage, the highest voltage, the lowest voltage and each
cell's voltage.
Battery Internal Resistance Meter
The user can check each cell's internal resistance.
Capacity Limit
The charging capacity is always calculated as the charging current multiplied by time. If the
charging capacity exceeds the limit, the process will be terminated automatically when you set
the maximum value.
Temperature Threshold*
The battery's internal chemical reaction will cause the temperature of the battery to rise. If the
temperature limit is reached, the process will be terminated.
* This function is available by connecting optional temperature probe, which is not included in the package.
Processing Time Limit:
You can also limit the maximum process time to avoid any possible defect.
· 04
Ultimate 1000W
WARNING AND SAFETY NOTES
These warnings and safety notes are particularly important. Please follow the
instructions for maximum safety; otherwise the charger and the battery can be
damaged or at worst it can cause a fire.
Never leave the charger unattended when it is connected to its power supply. If any
malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the
operation manual.
Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration.
Never drop it.
The allowable DC input voltage is 11~30V DC
This charger and the battery should be put on a heat-resistant, noninflammable and
nonconductive surface. Never place them on a car seat, carpet or similar. Keep all
the inflammable volatile materials away from operating area.
Make sure you know the specifications of the battery to be charged or discharged to
ensure it meets the requirements of this charger. If the program is set up incorrectly,
the battery and charger may be damaged .It can cause fire or explosion due to
overcharging.
Standard Battery Parameters
LiPo
LiIon
LiFe
LiHV
NiCd
MiMH
Pb
Nominal
Voltage
3.7V/cell
3.6V/cell
3.3V/cell
3.7V/cell
1.2V/cell
1.2V/cell
2.0V/cell
Max Charge
Voltage
4.2V/cell
4.1V/cell
3.6V/cell
4.35V/cell 1.5V/cell
1.5V/cell
2.46V/cell
Storage
Voltage
3.8V/cell
3.7V/cell
3.3V/cell
3.85V/cell n/a
n/a
n/a
Allowable
Fast Charge
≦1C
≦1C
≦4C
≦1C
1C-2C
≦0.4C
1C-2C
Min. Discharge
3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell 3.1-3.4V/cell 0.1-1.1V/cell 0.1-1.1V/cell 1.8V/cell
Voltage
Be very careful to choose the correct voltage for different types of battery otherwise you
may cause damage to the batteries. Incorrect settings could cause the cells to fire or
explode.
Ultimate 1000W
05 ·
WARNING AND SAFETY NOTES
Never attempt to charge or discharge the following types of batteries.
A battery pack which consists of different types of cells (including different
manufacturers)
A battery that is already fully charged or just slightly discharged.
Non-rechargeable batteries (Explosion hazard).
Batteries that require a different charge technique from NiCd, NiMh, LiPo or Gel cell
(Pb, Lead acid).
A faulty or damaged battery.
A battery fitted with an integral charge circuit or a protection circuit.
Batteries installed in a device or which are electrically linked to other components.
Batteries that are not expressly stated by the manufacturer to be suitable for the
currents the charger delivers during the charge process.
Please bear in mind the following points before commencing charging:
Did you select the appropriate program suitable for the type of battery you are
charging?
Did you set up adequate current for charging or discharging?
Have you checked the battery voltage? Lithium battery packs can be wired in parallel
and in series, i.e. a 2 cell pack can be 3.7V (in parallel) or 7.4V (in series).
Have you checked that all connections are firm and secure?
Make sure there are no intermittent contacts at any point in the circuit.
Charging
During charge process, a specific quantity of electrical energy is fed into the battery.
The charge quantity is calculated by multiplying charge current by charge time. The
maximum permissible charge current varies depending on the battery type or its
performance, and can be found in the information by the battery manufacturer. Only
batteries that are expressly stated to be capable of quick-charge are allowed to be
charged at rates higher than the standard charge current.
Connect the battery to the terminal of the charger: red is positive and black is
negative. Due to the difference between resistance of cable and connector, the
charger can not detect resistance of the battery pack, the essential requirement
for the charger to work properly is that the charge lead should be of adequate
conductor cross-section, and high quality connectors which are normally goldplated should be fitted to both ends.
Always refer to the manual by battery manufacturer about charging methods,
recommended charging current and charging time. Especially, the lithium battery
should be charged according the charging instruction provided by the manufacturer
strictly.
· 06
Ultimate 1000W
WARNING AND SAFETY NOTES
Attention should be paid to the connection of lithium battery especially.
Do not attempt to disassemble the battery pack arbitrarily.
Please get highlighted that lithium battery packs can be wired in parallel and in series.
In the parallel connection, the battery s capacity is calculated by multiplying single
battery capacity by the number of cells with total voltage stay the same. The voltages
imbalance may cause fire or explosion .Lithium battery is recommended to charge in
series.
Discharging
The main purpose of discharging is to clean residual capacity of the battery, or to
reduce the battery voltage to a defined level. The same attention should be paid to
the discharging process as charging. The final discharge voltage should be set up
correctly to avoid deep-discharging. Lithium battery can not be discharged to lower
than the minimum voltage, or it will cause a rapid loss of capacity or a total failure.
Generally, lithium battery doesn't need to be discharged. Please pay attention to the
minimum voltage of lithium battery to protect the battery.
Some rechargeable batteries have a memory effect. If they are partly used and
recharged before the whole charge is accomplished, they remember this and will only
use that part of their capacity next time. This is a memory effect. It is said that NiCd
and NiMH batteries are suffering from memory effect. NiCd has more memory effect
than NiMH.
Ultimate 1000W
07 ·
PROGRAM FLOW CHART
INC
DEC
PROGRAM SELECT
LiPo BATT
INC
LiFe BALANCE
2.0A 6.6V (2S)
DEC
LiHV BALANCE
2.0A 7.6V (2S)
DEC
4.20 4.19 4.19 V
0.00 0.00 0.00 V
DEC
1: 5mΩ 2: 3mΩ
3: 4mΩ 4: 3mΩ
DEC
Rest Time
CHG>DCHG 10Min
DEC
DEC
Lilo CHARGE
2.0A 7.2V (2S)
DEC
LiFe CHARGE
2.0A 6.6V (2S)
DEC
LiHV CHARGE
2.0A 7.6V (2S)
DEC
INC
LiPo FAST CHG
2.0A 7.4V (2S)
DEC
Lilo FAST CHG
2.0A 7.2V (2S)
DEC
LiFe FAST CHG
2.0A 6.6V (2S)
DEC
LiHV FAST CHG
2.0A 7.6V (2S)
DEC
INC
LiPo STORAGE
2.0A 7.4V (2S)
DEC
Lilo STORAGE
2.0A 7.2V (2S)
DEC
LiFe STORAGE
2.0A 6.6V (2S)
DEC
LiHV STORAGE
2.0A 7.6V (2S)
DEC
INC
LiPo DISCHARGE
2.0A 7.4V (2S)
DEC
Lilo DISCHARGE
2.0A 7.2V (2S)
DEC
LiFe DISCHARGE
2.0A 6.6V (2S)
DEC
LiHV DISCHARGE
2.0A 7.6V (2S)
DEC
INC
LiPo MICRO CHG
500mA 7.4V (2S)
DEC
LiIo MICRO CHG
500mA 7.4V (2S)
DEC
LiFe MICRO CHG
500mA 7.4V (2S)
DEC
LiHV MICRO CHG
500mA 7.4V (2S)
DEC
INC
LiPo MICRO STORE
500mA 7.4V (2S)
START
ENTER
INC
INC
INC
INC
INC
INC
LiIo MICRO STORE
500mA 7.4V (2S)
START
ENTER
INC
INC
INC
INC
INC
INC
LiFe MICRO STORE
500mA 7.4V (2S)
START
ENTER
INC
INC
INC
INC
INC
INC
LiHV MICRO STORE
500mA 7.4V (2S)
START
ENTER
INC
INC
0.00 V 0.00 V
DEC
MAIN 0.00V
H0.000V L0.000V
DEC
BATT/PROGRAM
BATT RESISTANCE
INC
DEC
LiPo CHARGE
2.0A 7.4V (2S)
DEC
PROGRAM SELECT
BATT METER
INC
Lilo BALANCE
2.0A 7.2V (2S)
INC
DEC
PROGRAM SELECT
LiHV BATT
INC
DEC
DEC
PROGRAM SELECT
LiFe BATT
INC
LiPo BALANCE
2.0A 7.4V (2S)
DEC
PROGRAM SELECT
Lilo BATT
INC
START
ENTER
START
ENTER
INC
5: 4mΩ 6: 3mΩ
DEC
PROGRAM SELECT
SYSTEM SET->
START
ENTER
INC
SAFETY TIMER
ON
120Min
INC
DEC
Capacity Cut-Off
ON
5000mAH
INC
DEC
INC
Key Beep
Buzzer
ON
ON
Ext. Temp
Int. Temp
0C
37C
DEC
CHARGE CURRENT
4.9A
DEC
DEC
Power Source?
DC Power Supply
INC
DEC INC
INC DEC
1.00
Batt Type
PROGRAM SELECT
BATT MEMORY
START
ENTER
INC
VERSION
Stop
BATT MEMORY [1]
ENTER SET
START
ENTER
BATT TYPE
LiPo
DEC
INC
DEC
LOAD FACTORY SET
ENTER
BATT VOLTS
7.4V ( 2S )
INC
DEC
INC
DEC
INC
INC
DEC
USE Regenerative
Discharger? > N
DSCH CURRENT
2.2A
INC
DEC
DSCH VOLTAGE
3.0V/CELL
INC
BATT MEMORY [1]
LiPo 7.4V (2S )
BATT MEMORY [1]
C:4.9A D:2.2A
START
ENTER
INC
SAVE PROGRAM
SAVE….
DEC
LiPo CHARGE
4.9A 7.4V(2S)
DEC
INC
SAVE PROGRAM
ENTER
DEC
LiPo FAST CHG
4.9A 7.4V(2S)
DEC
INC
TEMPERATURE
CUT-OFF
50C
DEC
LiPo STORAGE
4.9A 7.4V(2S)
DEC
DEC
TVC=YOUR RISK
4.20V
START/ENTER >3s
LiPo BALANCE
4.9A 7.4V(2S)
ENTER CHARGER
LOAD……
INC
DEC
INC
INC
INC
LiPo DISCHARGE
2.2A 7.4V(2S)
INC
DEC
LiPo MICRO CHG
500mA 7.4V (2S)
INC
INC DEC
ENTER
START
BATT MEMORY 2
NiMH 2.4V (2S)
START
ENTER
BATT TYPE
MiMH
INC
DEC
BATT VOLTS
2.4V (2S)
INC
DEC
CHARGE CURRENT
3.3A
INC
DEC
INC
TRICKLE
100mA
PEAK DELAY
1Min
DEC
INC
ENTER
START
BATT MEMORY 3
Pb 4V (2S)
START
ENTER
INC
SAVE PROGRAM
ENTER
DEC
BATT TYPE
Pb
DEC
INC
INC
DELTA PEAK SENSE
4Mv/C
DEC
BATT VOLTS
4.0V (2S)
DEC
INC
INC
DSCH VOLTAGE
1.1V/CELL
DEC
CHARGE CURRENT
3.3A
DEC
INC
INC
DSCH CURRENT
2.2A
DEC
DSCH CURRENT
1.5A
DEC
INC
INC
DSCH VOLTAGE
1.7V/CELL
ENTER
Pb CHARGE
2.0A 2.0V (1P)
INC
DEC
Pb DISCHARGE
0.1A 2.0V (1P)
INC
SAVE PROGRAM
ENTER
DEC
DEC
TEMPERATURE
CUT-OFF
50C
DEC
PROGRAM SELECT
NiCD BATT
INC
START
DEC
TEMPERATURE
CUT-OFF
50C
INC
PROGRAM SELECT
Pb BATT
DEC
LiPo MICRO STORE
500mA 7.4V (2S)
START
ENTER
INC
NiCD CHARGE
CURRENT 2.0A
DEC
NiMH CHARGE
CURRENT 2.0A
DEC
INC
NiCD Auto CHARGE
CURRENT 2.0A
DEC
NiMH Auto CHARGE
CURRENT 2.0A
DEC
INC
NiCD DISCHARGE
0.1A CUT: 1.0V
DEC
NiMH DISCHARGE
0.1A CUT: 1.0V
DEC
INC
NiCD RE-PEAK
1
DEC
NiMH RE-PEAK
1
DEC
NiCD CYCLE
CHG>DCHG
1
NiMH CYCLE
CHG>DCHG
1
DEC
PROGRAM SELECT
NiMH BATT
· 08
START
ENTER
INC
INC
INC
INC
Ultimate 1000W
OPERATION
BATT PROG / STOP Button:
It is used to stop the progress or go back to previous step/screen
DEC Button:
It is used to go through the menus and decrease the parameter value
INC Button:
It is used to go through the menus and increase the parameter value
ENTER / START Button:
It is used to enter parameter or store parameter on screen.
When you are willing to alter the parameter value in the program, press the
START/ENTER button to make it blink then change the value by pressing DEC and INC
button. The value will be stored by re-pressing the START/ENTER button. If there is
another parameter can be altered in the same screen, when you confirm the first
parameter value, the next parameter value will start to blink which means it is ready to
alert.
When you are willing to start the progress, press and hold the START/ENTER button for 3
seconds. When you are willing to stop the progress or go back to previous step/screen,
press the BATT PROG/STOP button once.
When you power on the charger, it will enter LiPo Battery balance program directly. You
could change the mode (balance mode, normal charge mode, fast charge mode, store
mode or discharge mode), enter the desired charging/discharging mode, set the referred
parameter and start the progress.
If you have no request for LiPo Battery program, please press the BATT PROG/STOP
button to enter BATT PROGRAM screen.
Ultimate 1000W
09 ·
OPERATING PROGRAM
Here is the detailed procedure to make the charger work. All the screens and operations
will take Li-Po BALANCE CHARGE program for example,
1. Connection
1). Connecting to power source
There are 2 kinds of power source: DC power supply and Lead Acid battery. After
you connect the power source to the charger, when you power up the charger for
the first time or load the factory default setting, please follow below steps,
Power Supply?
>DC Power Supply
ENTER
DC Supply:
Cut Volt.:
30.0A
11.0V
ENTER
DC Supply:
Cut Volt.:
DEC INC
DEC INC
Power Source
>Battery
30.0A
11.0V
ENTER
Bat.Supply:30.0A
Cut Volt.: 11.0V
ENTER
Bat.Supply:30.0A
Cut Volt.: 11.0V
DEC INC
Press the START/ENTER button to make the current value blink then change the
value by pressing DEC and INC button. The value will be stored by re-pressing the
START/ENTER button. At the same time cut voltage will start to blink, press DEC
and INC button to change the value and repress START/ENTER button to store it.
Note1: Make sure to choose the right power source and set up the right current
and cut voltage.
Note2: The charger will save the setting for next use if you don’t change it. So if
you change the power source, please make sure to change the setting in
the charger.
Connecting to DC power supply
Ultimate 1000W comes with male 4mm Bullet connectors attached to the power
INPUT cables. These cables are appropriate for attaching directly to most highquality AC-DC power supply units, such as EFUEL 1200W Power supply.
4mm Bullet
Connectors
plugging
to eFUEL power
supply directly
· 10
Ultimate 1000W
OPERATING PROGRAM
Important Notice
To take advantage of Ultimate 1000W’s full power capability, the power
source should be 30V DC, and output power should be capable of 1200W
or higher.
Low quality DC power source may damage your Ultimate 1000W charger.
We recommend you to choose EFUEL 1200W Power Supply.
Connecting to Battery supply
If you use the battery as the power source, please do set the right battery current and cut
voltage, or it will get damage to the charger and the charging battery.
2). Connecting the battery
Important!!! Before connecting a battery it is absolutely essential to check one last time
that you have set the parameters correctly. If the settings are incorrect, the battery may
be damaged, and could even burst into flames or explode. To avoid short circuits
between the banana plugs, always connect the charge leads to the charger first, and only
then to the battery. Reverse the sequence when disconnecting the pack.
3). Balance Socket
It is a MUST for charging Lithium (LiPo, Lilo, LiFe and LiHV) battery in
Charge, Fast Charge, Balance Charge and Storage mode. If you don't
connect the battery to the balance socket while the charger is working in
mentioned modes, the charger won't start working.
Balance Port Charging
If you charge the battery with the balance port, first, connect the balance
board to the charger, and then connect the battery balance wire to the
balance board.
The balance wire attached to the battery must
be connected to the charger with the black wire
aligned with the negative marking. Take care to
maintain correct polarity! (See the wiring
diagram below.)
This diagram shows the correct way to connect
your battery to the SKYRC Ultimate 1000W
while charging in the balance charge program
mode.
WARNING:
Failure to connect as shown in this diagram will damage this charger.
To avoid short circuit between the charge lead always connect the charge cable to the
charger first, then connect the battery. Reverse the sequence when disconnecting.
Ultimate 1000W
11 ·
OPERATING PROGRAM
2. Getting started
Locate the flowcharts show the entire programming menu. It is highly recommended to
have these flowcharts handy while learning to operate this charger.
There are two main ways in which to set the charger.
(1) A memory profile is available for setting and storing pertinent information for up to
10 different batteries. Once a battery's information is stored into a memory it will be
retained until changed again manually. Recalling a battery's memory number
makes the charger instantly ready to go!
(2) If you do not wish to use the battery memories, this charger can be manually set
before each use.
For following step, all are basing on manually set
BATT/PROGRAM
LiPo BATT
START/ENTER
LiPo BALANCE CHG
2.0A
11.1V (3S)
3. BATT/PROGRAM Select
Press INC and DEC to go through all the programs and press
START/ENTER to enter LiPo BATT Program.
4. Mode Select
Press INC and DEC to go through all the modes and press
START/ENTER to enter LiPo Balance Charge Mode.
START/ENTER
LiPo BALANCE CHG
2.0A
11.1V (3S)
START/ENTER
LiPo BALANCE CHG
2.0A
11.1V (3S)
START/ENTER
LiPo BALANCE CHG
2.0A
11.1V (3S)
START/ENTER
> 3 Seconds
BATTERY CHECK
WAIT...
R:3SER S:3SER
CANCEL(STOP)
· 12
5. Battery Setting
Press START/ENTER, the current value will start to blink, press
INC and DEC to change the value and press START/ENTER to
confirm your setting.
At the same time, the battery cells number will start to blink,
press INC and
DEC to change the value and press
START/ENTER to confirm your setting.
6. Program Start
Press and hold START/ENTER for 3 seconds to start the
program.
The charger is detecting the battery cell.
R shows the number of cells detected by the charger and S is
the number of cells set by you at the previous screen. If both
numbers are not identical, press STOP to go back to previous
screen to recheck the number of cells of the battery pack before
going ahead.
Ultimate 1000W
OPERATING PROGRAM
R:3SER S:3SER
CONFIRM(ENTER)
START/ENTER
LP4s 1.5A 12.14V
BAL 000:50 00022
R shows the number of cells detected by the charger and S is the
number of cells set by you at the previous screen. If both numbers
are identical, press START/ENTER to start charging process.
7. Charging Status Monitor
During charge process, real-time status will be showed as left screen.
VARIOUS INFORMATION DURING THE PROCESS
Press INC or DEC during charging or discharging process, you can inquire various
information on LCD screen .
LP4s 1.5A 12.14V
BAL 000:50 00022
Real-time status: battery type, battery cell, charge current, battery
voltage, elapsed time and charged capacity
INC
4.07 4.06 4.11 V
0.00 0.00 0.00 V
Voltage of each cell in the battery pack when the battery is
connected with balance lead.
INC
Charged capacity percentage and average cell voltage of the
battery pack.
Fuel= 90%
Cell= 4.10V
LP4s 1.5A 12.14V
BAL 000:50 00022
DEC
Final voltage when the program ends.
DEC
Input voltage.
DEC
Ext. Temp
Int. Temp
---37 C
Internal temperature.
Temperature probe is needed to show external temperature.
DEC
Temp Cut-Off
50 C
Cut off temperature
DEC
Safety timer ON and duration of time in minutes.
DEC
Capacity cut-off ON and the setting value of capacity.
Ultimate 1000W
13 ·
OPERATING PROGRAM
8. Program Stop
During the charging process, press STOP to stop the charging process.
9. Program Complete
When the charging process finishes, an audible sound will be heard.
Charging Program
Depends on different battery type, the operation programs are different.
Batt
Type
Operation
Program
CHARGE
DISCHARGE
REGENERATIVE
DISCHARGE*
LiPo
Lilon
LiFe
LiHV
STORAGE
FAST CHG
BAL CHARGE
MICRO CHARGE
MICRO STORAGE
The charger will charge NiMH and NiCd batteries using the charge
current set by the user.
AUTO CHG
In this program the charger detects the condition of the battery which
is connected to the output and automatically charges the battery.
Note: you should set up the upper limit of the charge current to
avoid damage by excessive feeding current. Some batteries of
low resistance and capacity can lead to higher current.
REGENERATIVE
DISCHARGE*
RE-PEAK
· 14
This mode is for discharging NiMH/NiCd battery.
This mode is for discharging NiMH/NiCd battery when the power
source is Lead Acid battery.
In re-peak charge mode, the charger can peak charge the battery
once, twice or three times in a row automatically. This is good for
confirming the battery is fully charged, and for checking how well the
battery receives fast charges.
CHARGE
1 to 5 cyclic and continuous process of charge>discharge or
discharge>charge is operable for battery refreshing and balancing to
stimulate the battery's activity.
This mode is for charging Pb battery.
DISCHARGE
This mode is for discharging Pb battery.
REGENERATIVE
DISCHARGE*
This mode is for discharging Pb battery when the power source is
Lead Acid battery.
CYCLE
Pb
This charging mode is for charging LiPo/LiFe/LiIon/LiHV battery in normal mode.
This mode is for discharging LiPo/LiFe/LiIon/LiHV battery.
This mode is for discharging LiPo/LiFe/LiIon/LiHV battery when the
power source is Lead Acid battery.
This program is for charging or discharging lithium battery which will
not be used for long time.
The charging capacity may be a bit smaller than normal charging but
the process time will be reduced.
This mode is for balancing the voltage of lithium-polymer battery cells
while charging.
This mode is for balancing the voltage of lithium-polymer battery cells
while charging with balance port.
This program is for charging or discharging lithium battery which will
not be used for long time with balance port.
CHARGE
DISCHARGE
NiMH
NiCd
Description
Ultimate 1000W
BATTERY MEMORY SET AND CALL OUT
REGENERATIVE DISCHARGE
Regenerative Discharge transforms most of the energy from the discharging battery pack to the Lead
Acid battery powering the charger. The regenerative discharge current can reach to 40A Max. It works
only when the power source is 6P or 12P Lead Acid battery.
For factory default setting, the Regenerative Discharge function is disabled. Please follow below steps
to active it,
PROGRAM SELECT
SYSTEM SET->
USE Regenerative
Discharger? > Y
When the power source is 6P or 12P Lead Acid battery and the Regenerative Discharge function is
active, all discharge modes will switch to generative discharge modes automatically.
For example,
LiPo DISCHARGE
2.0A
7.4V (2S)
LiPo REGEN DSC
2.0A
7.4V (2S)
Note1: Please make sure to set the right current and cut voltage of the Lead Acid battery and change
the setting when you change the power source every time.
Note2: If the power source is DC power supply, the Regenerative Discharge will be off automatically.
Note3: If the power source is 8P, 9P or 10P Lead Acid battery, but not 6P or 12P, even you active
regenerative discharge function, it will be off automatically.
Note4: If the Lead Acid battery is full charged in regenerative discharge mode, the charger will alarm 5
times(Like bi-bi-bi-bi-bi), then switch to internal discharge automatically until it finishes
discharge progress.
BATTERY MEMORY SET AND CALL OUT
The charger can store up to 10 different charge/discharge profiles for your convenience, and the
stored profiles can be recalled quickly without having to go through the setup process.
When you are willing to alter the parameter value in the program, press START/ENTER to make it
blink then change the value with INC or DEC. The value will be stored by pressing START/ENTER
once.
Note: All following screen are taking 2S(7.4V) LiPo battery for example.
1. Battery Memory Set
[ BATT MEMORY 1 ]
ENTER SET->
Enter the battery memory program.
(10 different charge/discharge profiles can be stored).
START/ENTER
BATT TYPE
LiPo
Set the battery type(LiPo/LiFe/LiIon/LiHV/NiMH/NiCd/Pb).
DEC INC
BATT VOLTS
7.4V ( 2S )
Set the voltage and number of cells(1S-8S).
DEC INC
Ultimate 1000W
15 ·
BATTERY MEMORY SET AND CALL OUT
CHARGE CURRENT
4.9A
Set the charge current(0.1-40.0A).
DEC INC
DSCH CURRENT
2.0A
Set the discharge current (0.1A-8.0A).
DEC INC
DSCH VOLTAGE
3.0V/CELL
Set the discharge voltage(3.0-3.3V/Cell).
DEC INC
TVC=YOUR RISK!
4.20V
Set the terminal voltage(4.18-4.25V).
DEC INC
SAVE PROGRAM
ENTER
Press ENTER to save program.
START/ENTER
SAVE PROGRAM
SAVE….
[ BATT MEMORY 1 ]
LiPo
7.4V (2S)
Indicate the battery type and battery cell of the saved profile.
[ BATT MEMORY 1 ]
C:4.9A
D:2.2A
Indicate the charge and discharge current of the saved profile.
Press the START/ENTER for 3 seconds to call out the memory.
START/ENTER
>3 Seconds
2. Battery Memory Call Out
ENTER CHARGER
LOAD……
Load the memory set
LiPo BALANCE CHG
4.9A
7.4V(2S)
Press START/ENTER for 3 seconds to start the process.
· 16
Ultimate 1000W
SYSTEM SETTING
It is essential for users to do system settings before use. After entering system setting
program, the screen displays the following information in sequence and the user can
change the value of parameter on each screen.
When you are willing to alter the parameter value in the program, press START/ENTER to
make it blink then change the value with INC or DEC. The value will be stored by
pressing START/ENTER once.
SELECTION
ITEM
Rest Time
CHG>DCHG
Safety
ON
10Min
Timer
120Min
Capacity Cut-Off
ON
5000mAH
Key Beep
Buzzer
ON
ON
Power Source?
DC Power Supply
Ultimate 1000W
1-60Min
OFF/
ON
(1-720 Min)
DESCRIPTION
A rest time allowing the battery to cool
down between charging/discharging cycle.
When you start a charge process, the
integral safety timer automatically starts
running at the same time. This is
programmed to prevent overcharge the
battery if it proves to be faulty, or if the
termination circuit cannot detect the battery
full. The value for the safety timer should be
generous enough to allow a full charge of
the battery.
OFF/
ON
(100-50000 mAh)
This program sets the maximum charge
capacity that will be supplied to the battery
during charge. If the delta peak voltage is
not detected nor the safety timer expired by
any reason, this feature will automatically
stop the process at the selected capacity
value.
OFF/ON
The beep sounds at every time touching
the buttons to confirm your action. The
beep or melody sounded at various times
during operation to alert different mode
changes.
DC Power Supply/
Choose the power source.
Battery
17 ·
SYSTEM SETTING
SELECTION
ITEM
USE Regenerative
Discharger? > Y
Ext. Temp
Int. Temp
· 18
0C
37C
N/Y
DESCRIPTION
Activate/Disable the Regenerative
Discharge function
The external temperature of the battery.
The internal temperature of the charger.
Load Factory Set
Enter
Press ENTER to load factory default setting.
Version
HW:1.00 FW: 1.10
It indicates the hardware and firmware
version.
Ultimate 1000W
BATTERY METER
The user can check battery's total voltage, the highest voltage, the lowest voltage and
each cell's voltage.
Please connect the battery to the charger main battery lead to battery socket and balance
wires to balance board.
This diagram shows the
correct way to connect
your battery to check
the voltage.
BATT/PROGRAM
BATT METER
Battery
Pack
Press the START/ENTER to enter the Lithium
Battery Meter program.
START
ENTER
4.20
4.18
4.19
4.18
4.19 V
4.19 V
The screen indicate each cell's voltage.
INC
0.00V
0.00V
INC
MAIN 25.13V
H4.200V L4.182V
Ultimate 1000W
The screen indicate the total voltage, the highest
voltage and the lowest voltage.
19 ·
BATTERY RESISTANCE METER
The user can check each cell's resistance.
Please connect the battery to the charger main battery lead to battery socket and balance
wires to balance socket.
005 003 003
005 004 003
mΩ
mΩ
This diagram shows the
correct way to connect
your battery to check
the resistance.
BATT/PROGRAM
BATT RESISTANCE
Battery
Pack
Press the START/ENTER to enter the Lithium
Battery Resistance program.
Start
Enter
1:
3:
5 mΩ 2 :
3 mΩ 4 :
5:
3 mΩ 6 :
4 mΩ
4 mΩ
The screen indicate each cell's resistance.
INC
· 20
4 mΩ
Ultimate 1000W
WARNING AND ERROR MESSAGE
In case of an error the screen will display the cause of error and emit an audible sound.
Incorrect polarity connected.
The battery is interrupted.
CONNECT ERROR
CHECK MAIN PORT
The battery connection is wrong.
BALANCE CONNECT
ERROR
The balance connect is wrong.
DC IN TOO LOW
Input voltage less than 11V.
DC IN TOO HIGH
Input voltage higher than 30V.
CELL ERROR
LOW VOLTAGE
Voltage of one cell in the battery pack is too low.
CELL ERROR
HIGH VOLTAGE
Voltage of one cell in the battery pack is too high.
CELL ERROR
VOLTAGE-INVALID
Voltage of one cell in the battery pack is invalid.
CELL NUMBER
INCORRECT
The cell number is wrong.
INT.TEMP.TOO HI
The internal temperature of the unit goes too high.
EXT.TEMP.TOO HI
The external temperature of the battery goes too high.
OVER CHARGE
CAPACITY LIMIT
The battery capacity is more than the maximum capacity
which the user sets.
OVER TIME LIMIT
The charging time is longer than the maximum charging
time which the user sets.
BATTERY WAS FULL
The battery voltage is higher than the maximum voltage
which the user sets when charging in balance mode.
Ultimate 1000W
21 ·
USING THE CHARGE CONTROL SOFTWARE “CHARGE MASTER”
CHARGE MASTER- FREE PC CONTROL SOFTWARE
The free “Charge Master”
software gives you unparalleled
ability to operate the charger
through the computer. You can
monitor pack voltage, cell
voltage and other data during
the charging, view charge date
in real-time graphs. And you can
initiate, control charging and
update firmware from “Charge
Master”.
In order to connect the charger
to the computer and use the
“Charge Master”, you are
required to use a USB cable
which is not included in this
package. The cable must be terminated on one end with “A” plug and the opposite end is
terminated with “micro-B” plug which can connect to charger directly.
The “Charge Master” can be download from www.skyrc.com.
SMART PHONE CONTROL VIA WI-FI MODULE (BOTH IOS AND ANDROID)
This charger can be controlled and operated
by smart phones via Wi-Fi module (optional part
SK-600075).
Wi-Fi Module
(optional part
SK-600075)
Scan with
your Smartphone
to download.
· 22
Ultimate 1000W
RECOMMENDED PRODUCTS
eFUEL 15-30V/50A Power Supply
SPECIFICATION
Voltage: 100-240V AC
Input AC Frequency: 50-60Hz
Output Voltage: 15-30V DC±0.5V
Output Current: 50A±1A
Over Temperature Protection: <65℃
Cooling Method: Cooling Fan
Dimensions: 305x170x85mm
Net weight: 3.08kg
SK-200015
Dual Port Safe Parallel Adapter
SPECIFICATION
Cell Count: 2~8S
Balance Connector Type: XH
Fuse Protect
Over Current Indicator
SK-600071
THE SET CONTAINS
1. SKYRC Ultimate 1000W Charger
2. 2-8S Multiple Balance
Board Adapter
3. Insulated Banana to Xt60
Battery Connector
4. Charging Cable with Insulated
1
2
Banana Connector
3
4
Ultimate 1000W
23 ·
SPECIFICATION
SPECIFICATION
DC Input Voltage : 11-30V
Controls: Button
Display Type: 2x16 LCD
Display Backlight: Blue
Case Material: Metal
Cooling System: Built-in fan x2pc
Case Size: 138x156x76mm
Weight: 1240g
PC Communications: USB Port for PC Control & Firmware Upgrade
External Port: Balance Socket-XH, Temperature Probe Socket,
Battery Socket, DC Input, Micro USB Port for PC and
Wi-Fi Module for Smart Phone Control
Delta Peak Detection: NiMH/NiCad: 3-15mV/cell (Default 4mV/cell)
Charge Cutoff Temperature: 20-80ºC(adjustable)
Charge Voltage: NiMH/NiCad: Delta peak detection
LiPo: 4.18-4.3V/cell
LiIon: 4.08-4.2V/cell
LiFe: 3.58-3.7V/cell
LiHV: 4.25-4.35V/cell
Balance Current: Max. 800mA/cell
Trickle Current for NiMH/NiCad: 50-300mA & OFF
Reading Voltage Range: 0.1-34.4V/cell
Battery Types/Cells: LiPo/LiIon/LiFe/LiHV: 1-8cells
NiMH/NiCad: 1-20cells
Pb: 2-24V
Battery Capacity Range: NiMH/NiCad: 100-50000mAh
LiPo/LiIon/LiFe/LiHV: 100-50000mAh
Pb: 100-50000mAh
Charge Current: 0.1A-1A (±0.3A) 1.1A-40A (±10%)
Safety Timer: 1-720minutes off
Charge Wattage: 1000W
Discharge Current: 0.1A-8A (±10%)
Balance Port Discharge Current: 10-800mA
Regenerative Discharge Current: 0.1-40.0A
Discharge Cut-off Voltage: NiMH/NiCad: 0.1-1.1V/cell
LiPo: 3.0-3.3V/cell
LiIon: 2.9—3.2V/cell
LiFe: 2.6-2.9V/cell
LiHV: 3.1-3.4V/cell
Pb: 1.8V
Discharge Wattage: 80W
Balance Cells: 8 cells
Memory: 10 different charge/discharge profiles
Charge Method: CC/CV for lithium types and lead (Pb) batteries
Delta-peak Sensitivity for NiMH/NiCad.
· 24
Ultimate 1000W
CONFORMITY DECLARATION
SKYRC Ultimate 1000W satisfy all relevant and mandatory CE directives and FCC Part 15
Subpart B: 2012.
For EC directives:
The product has been tested to meet the following technical standards:
EN 55014-1:2006+
A1:2009+A2:2011
EN 55014-1: Electromagnetic Compatibility Requirements for household appliances, electric tools
and similar apparatus -a Part 1: Emission
EN 55014-2:1997+
A1:2001+A2:2008
EN 55014-2: Electromagnetic Compatibility Requirements for household appliances, electric tools
and similar apparaturs - Part 2: Immunity product family
standard
This symbol means that you must dispose of electrical from the General household
waste when it reaches the end of its useful life. Take your charger to your local
waste collection point or recycling centre. This applies to all countries of the
European Union, and to other European countries with a separate waste collection
system.
Ultimate 1000W
25 ·
MAXIMUM CIRCUIT POWER CHART
Maximum circuit power chart
The actual amount of charge current feeding to the battery is automatically be limited to
1000 Watts, so not to exceed the charger's maximum rated charging power. The
maximum discharge power is approximately 80 Watts. The discharge current delivered to
the charger is limited by charger's internal thermal sensor for maximum discharge
current. If the internal temperature over 80 Celsius, the charger will be cut off and "TEMP
OVER ERR" will show on the LCD. In this case, please decrease discharging current.
Please refer following chart for maximum charging/discharging current.
Battery
Type
LiPo
LiIon
LiFe
LiHV
· 26
1000W
1S
3.7
80W
4.2
40.0
8.0
2S
7.4
8.4
40.0
8.0
3S
11.1
12.6
40.0
6.3
4S
14.8
16.8
40.0
4.7
5S
18.5
21.0
40.0
3.8
6S
22.2
25.2
39.6
3.1
7S
25.9
29.4
34.0
2.7
8S
29.6
33.6
29.7
2.3
1S
3.6
4.1
40.0
8.0
2S
7.2
8.2
40.0
8.0
3S
10.8
12.3
40.0
6.5
4S
14.4
16.4
40.0
4.8
5S
18.0
20.5
40.0
3.9
6S
21.6
24.6
40.0
3.2
7S
25.2
28.7
34.8
2.7
8S
28.8
32.8
30.4
2.4
1S
3.3
3.6
40.0
8.0
2S
6.6
7.2
40.0
8.0
3S
9.9
10.8
40.0
7.4
4S
13.2
14.4
40.0
5.5
5S
16.5
18.0
40.0
4.4
6S
19.8
21.6
40.0
3.7
7S
23.1
25.2
39.6
3.1
8S
26.4
28.8
34.7
2.7
1S
3.7
4.35
40.0
8.0
2S
7.4
8.7
40.0
8.0
3S
11.1
13.05
40.0
6.1
4S
14.8
17.4
40.0
4.5
5S
18.5
21.75
40.0
3.6
6S
22.2
26.1
38.3
3.0
7S
25.9
30.45
29.0
2.6
8S
29.6
34.8
28.7
2.2
Ultimate 1000W
MAXIMUM CIRCUIT POWER CHART
Battery
Type
NiCd/NiMH
Pb
Ultimate 1000W
1000W
80W
2
2.4
3.0
40.0
8.0
3
3.6
4.5
40.0
8.0
4
4.8
6.0
40.0
8.0
5
6.0
7.5
40.0
8.0
6
7.2
9.0
40.0
8.0
7
8.4
10.5
40.0
7.6
8
9.6
12.0
40.0
6.6
9
10.8
13.5
40.0
5.9
10
12.0
15.0
40.0
5.3
11
13.2
16.5
40.0
4.8
12
14.4
18.0
40.0
4.4
13
15.6
19.5
40.0
4.1
14
16.8
21.0
40.0
3.8
15
18.0
22.5
40.0
3.5
16
19.2
24.0
40.0
3.3
17
20.4
25.5
39.2
3.1
18
21.6
27.0
37.0
2.9
19
22.8
28.5
35.0
2.8
20
24.0
30.0
33.3
2.6
6.0
7.35
40.0
8.0
8.0
9.80
40.0
8.0
10.0
12.25
40.0
6.5
12.0
14.70
40.0
5.4
14.0
17.15
40.0
4.6
16.0
19.60
40.0
4.0
18.0
22.05
40.0
3.6
20.0
24.50
40.0
3.2
22.0
26.95
37.1
2.9
24.0
29.40
34.0
2.7
27 ·
COMMONLY USED TERMS
Commonly used terms
Final charge voltage: the voltage at which the battery's charge limit (capacity limit) is
reached. The charge process switches from a high current to a low maintenance rate
(trickle charge) at this point. From this point on further high current charging would cause
overheating and eventual terminal damage to the pack.
Final discharge voltage: the voltage at which the battery's discharge limit is reached. The
chemical composition of the batteries determines the level of this voltage. Below this
voltage the battery enters the deep discharge zone. Individual cells within the pack may
become reverse polarized in this condition, and this can cause permanent damage.
A, mA: unit of measurement relating to charge or discharge current.1000 mA = 1 A
(A=Ampere,mA=Milliampere)
Ah, mAh: unit of measurement for the capacity of a battery (Amperes x time unit; h = hour).
If a pack is charged for one hour at a current of 2 A, it has been fed 2 Ah of energy. It
receives the same quantity of charge (2 Ah) if it is charged for 4 hours at 0.5 A, or 15
minutes (=1/4 h) at 8 A.
'C'-rating: Capacity is also referred to as the 'C' rating. Some battery suppliers recommend
charge and discharge currents based on the battery 'C' rating. A battery's '1C' current is the
same number as the battery's rated capacity number, but noted in mA or amps. A 600mAh
battery has a 1C current value of 600mA, and a 3C current value of (3 x 600mA) 1800mA or
1.8A. The 1C current value for a 3200mAh battery would be 3200mA (3.2A).
Nominal voltage(V): The nominal voltage of the battery pack can be determined as follows;
-.NiCd or NiMH: multiply the total number of cells in the pack by 1.2. A 8-cell pack will have a
nominal voltage of 9.6 volts (8x1.2).
-.LiPo: multiply the total number of cells in the pack by 3.7. A 3-cell LiPo wired in series will
have a nominal voltage of 11.1 volts (3x3.7).
-.LiIo: multiply the total number of cells in the pack by 3.6. A 2-cell LiIo wired in series will have
a nominal voltage of 7.2 volts (2x3.6).
-.LiFe: multiply the total number of cells in the pack by 3.3. A 4-cell LiIo wired in series will have
a nominal voltage of 13.2 volts (4x3.3).
If the nominal voltage of the battery is not printed on the battery's label, consult your battery
manufacturer or supplier. Do not guess the rated voltage of battery.
· 28
Ultimate 1000W
WARRANTY AND SERVICE
Liability exclusion
This charger is designed and approved exclusively for use with the types of battery stated
in this Instruction Manual. SkyRC accepts no liability of any kind if the charger is used for
any purpose other than that stated.
We are unable to ensure that you follow the instructions supplied with the charger, and
we have no control over the methods you employ for using, operating and maintaining the
device. For this reason we are obliged to deny all liability for loss, damage or costs which
are incurred due to the incompetent or incorrect use and operation of our products, or
which are connected with such operation in any way.Unless otherwise prescribed by law,
our obligation to pay compensation, regardless of the legal argument employed, is limited
to the invoice value of those SkyRC products which were immediately and directly
involved in the event in which the damage occurred.
Warranty and service
We guarantee this product to be free of manufacturing and assembly defects for a period of
one year from the time of purchase. The warranty only applies to material or operational
defects, which are present at the time of purchase. During that period, we will repair or
replace free of service charge for products deemed defective due to those causes.
This warranty is not valid for any damage or subsequent damage arising as a result of misuse,
modification or as a result of failure to observe the procedures outlined in this manual.
Note:
1. The warranty service is valid in China only.
2. If you need warranty service overseas, please contact your dealer in the first
instance, who is responsible for processing guarantee claims overseas. Due
to high shipping cost, complicated custom clearance procedures to send
back to China. Please understand SkyRC can't provide warranty service to
overseas end user directly.
3. If you have any questions which are not mentioned in the manual, please
feel free to send email to info@skyrc.cn
Ultimate 1000W
29 ·
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
All specifications and figures are subject to change without notice.
Printed in China
2014.11
7504-0539-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising