R 5 VV A - Hotex
R 5 Plus • R 5 V.V. • R 6 • R 6 V.V.
SUMMARY
WARRANTY
IMPORTANT WARNING
INTRODUCTION TO YOUR NEW
R 5 Plus • R 5 V.V. • R 6 • R 6 V.V.
MAINTENANCE
• Blade
• Motor seal
TECHNICAL SPECIFICATIONS
TABLE-TOP CUTTER MIXER
• Weight
SWITCHING THE MACHINE ON
• Dimensions
• Advices on electrical connections
• Working height
• Control panel
• Noise level
ASSEMBLY
USES AND EXAMPLES
OPTIONS
• Electrical data
SAFETY
STANDARDS
CLEANING
• Motor base
TECHNICAL DATA
• Cutter
• Exploded views
• Blade
• Electric diagram
13
ROBOT-COUPE S.N.C., LIMITED WARRANTY
Your new ROBOT-COUPE appliance is warranted to the original buyer for a period of
one year from the date of sale if you
bought it from ROBOT-COUPE S.N.C.
If you bought your ROBOT-COUPE product
from a distributor your product is covered
by your distributor’s warranty (Please check
with your distributor terms and conditions
of the warranty).
The ROBOT-COUPE S.N.C. limited warranty
is against defects in material and/or workmanship.
2 - Labour to sharpen and/ or replacements for
blades which have become blunt, chipped or
worn after a normal or excessive period of use.
3 - Materials or labour to replace or repair
scratched, stained, chipped, pitted, dented or
discoloured surfaces, blades, knives, attachments
or accessories.
1 -
Damage caused by abuse, misuse, dropping, or other similar damage caused by or
resulting from failure to follow assembly, operating, cleaning, user maintenance or storage instructions.
14
SHIPPING DAMAGES. Visible and latent
defects are the responsibility of the freight carrier.
The consignee must inform the carrier and consignor immediately, or upon discovery in the case
of latent defects.
KEEP ALL ORIGINAL CONTAINERS AND
PACKING MATERIALS FOR CARRIER INSPECTION.
4 - Any
alteration, addition or repair that has
not been carried out by the company or an
approved service agency.
5 - Transportation of the appliance to or from an
approved service agency.
THE FOLLOWING ARE NOT COVERED
BY THE ROBOT-COUPE S.N.C.
WARRANTY:
8 -
Neither ROBOT-COUPE S.N.C. nor its affiliated
companies or any of its distributors, directors,
agents, employees, or insurers will be liable for
indirect damage, losses, or expenses linked to the
appliance or the inability to use it.
6 - Labour charges to install or test new attachments or accessories (i.e., bowls, discs, blades, attachments) which have been arbitrarity replaced.
7 - The cost of changing direction-of-rotation of
three-phase electric motors (Installer is responsible).
The ROBOT-COUPE S . N . C . warranty is
given expressly and in lieu of all other
warranties, expressed or implied, for
merchantability and for fitness toward a
particular purpose and constitutes the only
warranty made by ROBOT-COUPE S.N.C.
France.
RECOMMENDATIONS CONCERNING THE INSTALLATION OF VARIABLE-SPEED
APPLIANCES AND PERSONAL SAFETY
These recommendations apply to machines equipped with an induction motor and a single-phase
wobbulator.
NB :
- The electrical circuit and the protective devices
must comply with national regulations.
- The machine must be wired in by a qualified
electrician
Protecting your appliance
• Like all electronic devices, wobbulators include components that are sensitive to electrostatic discharges
(ESDs). Before conducting any work on these wobbulators, technicians must therefore rid themselves
of electrostatic charges.
• The machine must be disconnected from the
mains supply before any internal connection operations are carried out.
• Repeatedly switching on the appliance will cause
the wobbulator to overload and may result in its
destruction. After the machine has been switched
off, you must wait for 3 minutes before switching
it back on again.
• You must connect the machine to a 200-240 V / 50
or 60 Hz single-phase* alternating current supply
with an earthed socket. A higher voltage will
destroy the wobbulator.
• Several variable-speed appliances are connected
to the same GFCI.
• The appliance produces a fault current that is
above the GFCI’s actual trip threshold.
• The earthed socket ensures operator safety.
Circuit interrupters ensuring user safety
Caution : As there are manufacturing tolerances,
Ground fault circuit interrupters (GFCIs) intended
for variable-speed appliances need to be selected
with great care in order to ensure operator safety.
GFCIs may be sensitive to alternating current
(type AC), impulse current (type A) or all currents
(type B).
the actual trip threshold of a GFCI will be between
50% and 100% of its theoretical nominal threshold.
Should a problem arise, measure the fault current
and the GFCI’s actual trip threshold.
Danger ! Wobbulators feature a bridge-connected
rectifier of the mains supply voltage. For this
reason, in the event of an ear th contact, a
continuous fault current may fail to trip a differential
circuit breaker that is only sensitive to alternating
current (type AC).
As the appliance has a single-phase* supply, it is
therefore advisable to use a GFCI that is sensitive to
impulse current (type A), identified by the following
symbol :
.
You can begin by consulting the characteristics of
your appliance in the table below :
Appliance
R 5 V.V.
R 6 V.V.
Conductor
Mains supply Cross-section
(mm2)
200 - 240V
50 oR 60 Hz
single-phase
2,5
GFCI (Ph + N)
Gauge (A)
Threshold (mA)
B20
≥ 30
* Except for specific three-phase 200-240 V models
sold in Japan.
Caution : these GFCIs may go under different
Wiring
names, according to the manufacturer.
• The appliance requires single-phase* current as
far as the wobbulator, which turns the latter into
variable-speed three-phase current to supply the
motor.
Appliances with wobbulators produce a fault
current on the earth wire. This current may be
sufficient to trip the differential circuit breaker
unnecessarily. This may occur if :
15
IMPORTANT WARNING
W A R N I N G
KEEP THESE INSTRUCTIONS
IN A SAFE PLACE
WARNING: In order to limit accidents such as electric shocks, personal injury or fire, and in order to limit material damage due to misuse
of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to
know your appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure that
anyone else who may use the mixer also reads them beforehand.
UNPACKING
ASSEMBLY PROCEDURES
• Carefully remove the equipment from the packaging
and take out all the boxes or packets containing
attachments or specific items.
• Follow the various assembly procedures carefully
(see page 17) and make sure that all the attachments
are correctly positioned.
• WARNING - some of the tools are very sharp e.g.
blade, discs... etc.
INSTALLATION
• We recommend you install your machine on a
perfectly stable solid base.
CONNECTION
• Always check that your mains supply corresponds
to that indicated on the rating plate on the motor
unit and that it can take the amperage.
• Do not open the lid until the motor has come to a
complete stop.
• Never tamper with the locking and safety systems.
• Never put a hand object in the bowl while the
machine is operating.
• Never force the ingredients down with your
hands.
• Do not overload the machine.
CLEANING
HANDLING
• As a precaution, always unplung your appliance
before cleaning it.
• Always clean the appliance and its attachments at
the end of each cycle.
• Never place the motor unit in water.
• Always take care when handling the blades or
discs - they are very sharp.
• For parts made of aluminum alloys, use cleaning
fluids suitable for aluminum.
• The machine must be earthed.
16
USE
• For plastic parts , do not use detergents that are
too alkaline (i.e., containing too much caustic soda
or ammonia...)
• Robot-Coupe can in no way be held responsible
for the user’s failure to follow the basic rules of
cleaning and hygiene.
MAINTENANCE
• Before opening the motor housing, it is absolutely
vital to unplung the appliance.
• Check the seals and washers regularly and
ensure that the safety devices are in good working
order.
• It is particularly important to maintain and check
the attachments since certain ingredients contain
corrosive agents e.g. citric acid.
• Never operate the appliance if the power cord
or plug has been damaged in any way or if the
appliance fails to work properly or has been damaged
in any way.
• Do not hesitate to contact your local Maintenance
Department if something appears to be wrong.
INTRODUCTION TO YOUR
NEW R 5 Plus • R 5 V.V. •
R 6 • R 6 V.V. TABLE-TOP
CUTTER MIXER
The R 5 Plus, R 5 V.V., R 6 or R 6 V.V. is perfectly
geared to professional needs. It can perform any
number of tasks, which you will gradually discover
as you use it.
This machine can be used to process meat, vegetables, fine stuffing, mousse, grinding, kneading,...
in less than 5 minutes for even the longest tasks.
Its numerous functions will open the door to a whole
new culinary world.
Thanks to its simple design, all components requiring
frequent handling for maintenance or cleaning can
be fitted and removed in a trice.
To make things easier for you, this manual gives a
breakdown of all the various fitting operations.
This manual contains impor tant information
designed to help the user get the most out of his or
her bowl cutter/vegetable preparation device.
We therefore recommend that you read it carefully
before using your machine.
We have also included a few examples to help you
get the feel of your new machine and appreciate its
numerous advantages.
SWITCHING ON
THE MACHINE
• ADVICE ON ELECTRICAL CONNNECTIONS
Before plugging in, check that your power supply
corresponds to that indicated on the machine’s
identification plate.
W A R N I N G
This appliance must be plugged into an
earthed socket (risk of electrocution).
THREE PHASE R 5 Plus • R 6
The R5 Plus/R6 come with different types of
motor :
230 x 400 V / 50 Hz / 3
400 V / 50 Hz / 3
220 V / 60 Hz / 3
380 V / 60 Hz / 3
This machine is supplied with a cable to which you
simply attach the appropriate electrical plug or
isolator for your system. The cable has four wires,
one earth wire, plus three phases wires.
If you have a 4-pin plug:
1) Connect the green and yellow earth wire to the
earth pin.
2) Connect the three other wires to the remaining
pins.
If you have more than 4 pins in the plug, please
note the ROBOT-COUPE does not require a neutral
wire.
Switch on the empty machine, making sure that
the blade is rotating properly in an anti-clockwise
direction.
On the motor unit and on the lid a arrow marks the
blade rotation directions.
If the blade turns in a clockwise direction, swap
over two wires.
GREEN YELLOW is the earth,
DO NOT DISCONNECT
Swap either :
• SINGLE PHASE R 5 Plus
The R5 Plus is available with motor ratings :
230 V / 50 Hz / 1
220 V / 60 Hz / 1
The machine comes with a single phase plug
connected to a power cord.
• SINGLE PHASE R 5 V.V. • R 6 V.V.
W A R N I N G
Before plugging in, read carefully the recommandations relating to the machines installation
on page 15.
The R 6 V.V. is available with motor ratings +
variabe speed : 230 V / 50-60 Hz / 1
The standardized plug must be calibrated to a minimum of 13 amps and preferably 20 amps, if the
appliance is used intensively.
• CONTROL PANEL
Red switch
= Off switch
Green switch = On switch
Black switch = Pulse control
R 5 Plus / R 6: Speed selector = 1.500 or 3.000 rpm.
R 5 V.V. / R 6 V.V.: Speed variation from
300 to 3.000 rpm.
ASSEMBLY
1) With the motor base
facing you, position the
cutter bowl on the motor
base.
the 1 and the 2
the 1 and the 3
or the 2 and the 3
17
USES AND EXAMPLES
2) Turn the bowl to the
right until it locks.
The cutter will enable your to perform all your
cutting tasks in minimum time; we recommend
therefore, that you keep a close eye on the mixture
in order to obtain the desired results.
The pulse control allows you to stop and start the
machine for high-precision control when working
with certain types of ingredients.
USES
3) Engage the blade on
the motor shaft and lower it right to the bottom
of the bowl.
Make sure that it is
correctly positioned, by
rotating it in the bowl.
R6
R5 Plus
R5 V.V. R6 V.V.
Suggested Processing
Max.
Max.
speed
time
processing processing
quantity quantity (in rpm) (in mn)
(in kg)
(in kg)
USES
R5 Plus
R6
R5 V.V. R6 V.V.
Suggested Processing
Max.
Max.
speed
time
processing processing
quantity quantity (in rpm) (in mn)
(in kg)
(in kg)
2
2
2
2,5
2,5
2,5
900/
1500
900/
1500
900/
1500
1
1
1
1,5
1,5
1,5
900/
1500
900/
1500
900/
1500
KNEAD
Shortcrust pasty/Shortbread
Flaky pastry
Pizza dough
GRIND
Dried fruit
Ice
Breadcrumbs
• MEAT
Hamburger/steak tartare
1,5
2
1200/
1500
3
Sausagemeat/tomatoes
2
2,5
1200/
1500
3
2,5
2,5
1200/
1500
3
The cutter version has numerous other applications.
The above quantities and times are approximate
and may vary according to the quality of the ingredients and recipes.
OPTIONS
• FISH
Brandade
2,5
3
3000
5
Terrines
2,5
3
3000
5
• VEGETABLES
Garlic/parsley/onion/shallots 0,5/1,0 0,5/1,5
1500/
2000
3
Soup/purées
3000
3
2
3
2500/
2
3
2500/
3000
4
Mayonnaise/ailloli/rémoulade
3
3,5
2500/
3000
4
Hollandaise/béarnaise
2
3
2500/
3000
4
Snail or salmon butter
2
2,5
2500/
3000
4
• FRUIT
Compotes/purées
EMULSIFY
The device is now ready for use. The green light
should therefore be illuminated.
18
4
4
4
CHOP
Terrine/pâté
4) Place the lid on the
bowl and rotate to the
right until it clicks.
4
4
4
For the R 5 Plus and
R 5 V.V. models, a serrated
blade knife is available as
an option.
For the R 6 and R 6 V.V.
models, serrated blades are
available as an option.
The serrated blades are recommended for grinding
and kneading tasks.
CLEANING
In order to keep the motor completely watertight, it
is advisable to check the motor seal regularly for
wear and tear and replace if necessary.
The motor seal can be easily replaced without having to remove the motor, so we strongly advise you
to ensure that is in good condition.
W A R N I N G
As a precaution, always unplug your appliance
before cleaning it (risk of electrocution).
• MOTOR BASE
TECHNICAL
SPECIFICATIONS
Never immerse the motor base in water. Clean
using a damp cloth or sponge.
• CUTTER
After removing the lid, remove the bowl from the
motor base by pushing the trigger fitted in the
handle. Pull up to disengage, leaving the blade in
the bowl in order to prevent any spillage when
working with liquids.
If the food has a solid consistency, remove the blade
and empty the bowl.
Replace the bowl, place the blade back on the shaft
and switch on the machine in order to remove any
mixture which may have stuck to the blade.
If you wish, you can rinse the bowl by filling it with
hot water and switching on for a few minutes.
• BLADE
The stainless steel blade of R 6 - R 6 V.V. is easy to
dismantle and to clean.
After cleaning the blade, always dry the blades well
to prevent rusting.
I M P O R T A N T
Check that your detergent is suitable for
cleaning plastic parts. Some washing agents are
too alkaline (e.g. high levels of caustic soda or
ammonia) and totally incompatible with certain
types of plastic, causing them to deteriorate
rapidly.
Ensure power supply to machine is disconnected.
1 - Place blade dismantling tool over shaft onto
motor base.
2 - Fit blade onto shaft ensuring it is correctly
positioned.
3 - Insert bar into blade cap and turn anti-clockwise to dismantle .
When re-assembling do not over tighten.
A - Upper blade.
B - Lower blade.
MAINTENANCE
• WEIGHT
net weight
24 kg
25 kg
25 kg
26 kg
R 5 Plus
R 5 V.V.
R6
R 6 V.V.
gross weight
26 kg
27 kg
27 kg
28 kg
• DIMENSIONS (in mm)
R 5 Plus
R 5 V.V.
R6
R 6 V.V.
A
480
480
520
520
B
350
350
350
350
C
280
280
280
280
D
265
265
265
265
• BLADE
We strongly recommend that the blades (smooth
ones) are sharpened daily using sharpening stone
supplied with machine.
The quality of the cut depends mainly on the
sharpness of your blades and the degree of wear.
The blades are actually wearing parts, which
should be replaced occasionally to ensure consistent
quality in the final product.
• MOTOR SEAL
The motor seal on the shaft should be lubricated
regularly using a food safe lubricant.
• WORKING HEIGHT
We recommend that you position the food processor
on a stable worktop so that the upper edge of the large
feed hopper is at a height of between 1.20 m and
1.30 m.
19
• NOISE LEVEL
R 6 three-phase machines
The equivalent continuous sound level when the
food processor is operating on no-load is less than
70 db (A).
• ELECTRICAL DATA
230 x 400 V /
50 Hz
R 5 Plus single-phase machine
Speed
(rpm)
Motor
Motor
Power
(watts)
Intensity
(amp.)
230 V / 50Hz
1500
900
16.0
220 V / 60 Hz
1500
900
16.0
400 V /50 Hz
220 V /60 Hz
Motor
Motor
230 x 400 V /
50 Hz
400 V /50 Hz
220 V /60 Hz
Speed
2
(rpm)
1500
Power
(watts)
3000
1500
3000
1800
3600
1200
750
2.7
1200
3.4
750
4.7
1200
6.5
R 5 V.V. single-phase machines
Motor
230 V / 50-60 Hz
20
1500
Power
(watts)
1300
230 V=4.4
400 V=2.5
230 V=7.0
400 V=4.0
800
2.7
1300
3.4
800
4.7
1300
6.5
800
3000
1500
3000
1800
3600
Intensity
(amp.)
Speed
(rpm)
Speed
(rpm)
Power
(watts)
Intensity
(amp.)
300 to 3000
1300
12
All the models are fitted with a thermal cut-out
which automatically stops the motor if the machine
is left on for too long or overloaded.
If this happens, allow the machine to cool completely before restarting.
STANDARDS
MACHINES IN COMPLIANCE WITH:
• The following European directives and related national legislation:
Power
(watts)
Intensity
(amp.)
Intensity
(amp.)
230 V=4.4
400 V=2.5
230 V=7.0
400 V=4.0
750
Speed
2
(rpm)
R 6 V.V. single-phase machines
R 5 Plus three-phase machines
Speed
1
(rpm)
Speed
1
(rpm)
In order to avoid splashing when processing liquid
preparation, we recommend you stop the machine
before opening the lid.
- Modified "machinery" directive 98/37/EEC,
- "Low voltage" directive 73/23/EEC,
- "EMC" directive 89/336/EEC,
230 V / 50-60 Hz
300 to 3000
1500
13
SAFETY
These models are fitted with a magnetic safety
device and motor braking system.
As soon as you open the lid of the cutter bowl or
the vegetable attachment, the motor stops.
To restart the machine, simply close the lid and
press the green switch.
W A R N I N G
The blades are extremely sharp. Handle with
care.
- "Materials and parts in food contact" directive
89/109/EEC,
- "Plastic materials and parts in food contact" directive 90/128/EEC.
• The following European harmonized standards
and standards setting out health and safety rules:
- EN 292 - 1 and - 2,
- EN 60204 -1 (1998),
- For Food Processors and blenders : EN 12852.
12
R 5 A Plus TRI
* voir tarif machines / See export price list
02/1998
a
R 5 A Plus TRI
13
* voir tarif machines / See export price list
02/2000
MAJ : 02/2000
a
14
R 5 A Plus MONO
* voir tarif machines / See export price list
03/1999
R 5 A Plus MONO
15
* voir tarif machines / See export price list
02/2000
MAJ : 02/2000 a
16
R 5 V.V. A
* voir tarif machines / See export price list
03/1999
R 5 V.V. A
17
* voir tarif machines / See export price list
03/1999
R 5 V.V. A
02/2000
19
MAJ : 02/2000 a
20
R 6 A
* voir tarif machines / See export price list
03/1999
R 6 A
21
* voir tarif machines / See export price list
02/2000
MAJ : 02/2000
a
R 6 A
03/1999
23
24
R 6 V.V. A
* voir tarif machines / See export price list
02/1998
R 6 V.V. A
25
* voir tarif machines / See export price list
02/1998
R 6 V.V. A
02/2000
27
MAJ : 02/2000
b
28
29
30
31
32
33
Administration Commerciale France &
Agence de Service Après-Vente
Export Department
Service Après-Vente
pour la Région Parisienne
Tél. : 03 85 69 50 00 - Fax : 03 85 69 50 07
Tél. : 01 43 98 88 15 - Fax : 01 43 74 36 26
Tel. : + 33 1 43 98 88 33 - Fax : + 33 1 43 74 36 26
18, rue Clément Viénot - BP 157
12, avenue du Maréchal Leclerc - BP 134
13, rue Clément Viénot
71305 Montceau-en-Bourgogne Cedex
94305 Vincennes Cedex
94305 Vincennes Cedex - France
http://www.robot-coupe.com - email : international@robot-coupe.com
email : france@robot-coupe.fr
We reserve the right to alter at any time without notice the technical specifications of this appliance.
© All rights reserved for all countries by: ROBOT-COUPE S.N.C.
Réf. : 401 796 - 11/2005 - R 5 Plus • R 5 V.V. • R 6 • R 6 V.V.
FABRIQUÉ EN FRANCE PAR ROBOT-COUPE S.N.C.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising