EDNord - Xyron Pro 1250 Multifinktionsmaskine Brugsanvisning

EDNord - Xyron Pro 1250 Multifinktionsmaskine Brugsanvisning
®
Pro1250
Adhesive Application and Laminating System
U
S
E
R
’
S
G
U
I
D
E
Adhesive Application &
Laminating System
Your Xyron Pro1250 is designed to permanently apply an adhesive or clear film to the
front and/or back of any substrate that is run through the machine. The lamination film
and adhesive are not designed to be removed without substantial damage to the laminated
substrate or mounting surface. This process is NOT recommended for any precious or single
source documents. Always test before use – may not be compatible with some surfaces.
The system is designed to be used with one of the following replacement cartridges:
DL1201-150
SL1201-150
Two-Sided Lamination – General Use – 150'
Single-Sided Lamination – General Use – 150'
LAT1201-100
LAT1206-100
One Side Laminate / One Side Adhesive Application – High Tack – 100'
One Side Laminate / One Side Adhesive Application – Repositionable – 100'
AT1201-100
AT1202-100
AT1205-100
AT1206-100
Adhesive
Adhesive
Adhesive
Adhesive
Application
Application
Application
Application
–
–
–
–
High Tack – 100'
Low Tack – 100'
Acid Free – 100'
Repositionable – 100'
Consult your authorized Xyron dealer for information on other supplies.
Please follow the attached directions carefully.
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Understanding the
Xyron Pro1250’s Parts & Functions
Input Tray
Used to guide items into
the machine. Leading edge
of documents should slide
underneath paddle for
best results.
Paddle
Used to provide back
tension on delicate or
long items to ensure
wrinkle-free results.
Top Cover
Opens up for cartridge
replacement (see label
when open).
Cut Blade
Used to cut items after they
have exited machine. To use,
press downward and slide
to the right or left.
Crank Handle
Used to advance cartridge
supplies and item when
rotated clockwise.
Replaceable Supply Cartridge
(see various types in Refill Cartridge section)
Top Cover
Shown open for cartridge
removal/installation.
Input Tray
Shown extended
for cartridge
removal/installation.
Lifting Points
Areas located on
both sides of machine
used for lifting.
Upper Cut Bar
and Upper Roller
Assembly
Slides out when
output tray
is extended.
Output Tray
Shown extended for cartridge
removal/installation.
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Setting Up
Remove the Xyron Pro1250 and crank handle from the packaging. Install the crank handle
by carefully threading it clockwise into the threaded opening in the side plate until snug.
Cartridge Replacement
Slide input tray
out away from
machine. With both
hands, lift and slide
output tray away
from machine.
1
Input
Tray
Output Tray
With top cover open,
lift out used cartridge.
Install new cartridge completely
and ensure film rests evenly
on lower roller. Make certain
the cartridge label faces the
side of the machine with the
crank handle.
2
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Cartridge Replacement
Grasp
the film
and pull the
film forward
2 to 4 inches
(4 to 6 cm).
3
Place the
film under
the metal bar
with the orange
blade holder
and under the
top black roller.
4
Using both
hands as
shown, slide the
output tray towards
machine completely.
Push down to ensure
the tray is seated.
5
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Cartridge Replacement
Turn the handle in
the direction of the
arrow (clockwise). The
film should advance
below the orange blade
holder. Continue cranking
until film is aligned and
wrinkle-free.
6
Press down
on orange
blade holder and
then slide in either
direction to trim
excess film. Close
top cover.
7
Slide
input
tray back
into machine
completely.
8
If You Have Additional Questions, Contact the Xyron Technical Hotline:
800-793-3523 in the U.S.A. and +45-7594-5866 in Europe
E-mail address in the U.S.A.: comments@xyron.com
E-mail address in Europe: europe@xyron.com
Also, check out our website at www.xyron.com
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Basic Operation
Before inserting your
document, turn crank handle
clockwise one revolution to ensure
film is wrinkle-free. Insert and align
document on feed tray. Extend the
document underneath the paddle
on the feed tray and completely
into the cartridge opening until it
touches the film/adhesive.
1
Gently guide the document
forward while turning the crank
handle clockwise. TIP: To save a later
trimming operation, trim off any excess
material on the leading edge of the
output (with cut blade) before advancing
completely through the dispenser.
2
Trim to desired length using the
cut blade at the roller exit. Apply
downward pressure on the orange
blade holder and slide to the left or
right. When applying adhesive, remove
the protective clear film on top to
eliminate excess adhesive from around
your item. Remove white liner when
you’re ready to adhere to your item.
3
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Basic Operation
How to Do Two-Sided Lamination
Verify that a front and back lamination cartridge (designated DL1200 series on the cartridge
label) is installed. Follow steps 1, 2 & 3 under Basic Operation.
How to Do Single-Sided Lamination
Verify that a front-side lamination cartridge (designated SL1200 series on the cartridge label)
is installed. Place item on tray with side to be laminated face up. Follow steps 1, 2 & 3
under Basic Operation.
How to Apply Adhesive to One Side of an Item
Verify that an adhesive transfer cartridge (designated AT1200 series on the cartridge label)
is installed. Place the side of the document to which you want adhesive applied face down
on the tray. Follow steps 1, 2 & 3 under Basic Operation. Peel away and discard clear
plastic protective film. When ready, peel away the white paper liner
from the backside of document and mount your item.
How to Do Front-Side Lamination with Back-Side Adhesive Application
Verify that a laminating/back side adhesive cartridge (designated LAT1200 series on the
cartridge label) is installed. Place the side of the document to which you want adhesive
applied face down on the tray. The side facing up should be the side you want laminated.
Follow steps 1, 2 & 3 under Basic Operation. Peel away the white paper liner from the
backside of document prior to mounting.
TIP: To save a later trimming operation, turn the crank to advance the document until the
leading edge is aligned with the upper blade bar supporting the cut blade. Trim excess
material from the leading edge of the document. Continue to crank document through
machine and trim when finished.
Refill Cartridges
Product No.
Description
DL1201-150
SL1201-150
LAT1201-100
LAT1206-100
AT1201-100
AT1202-100
AT1205-100
AT1206-100
Two-Sided Lamination – General Use
Single-Sided Lamination – General Use
One Side Laminate / One Side Adhesive Application – High Tack
One Side Laminate / One Side Adhesive Application – Repositionable
Adhesive Application – High Tack
Adhesive Application – Low Tack
Adhesive Application – Acid Free
Adhesive Application – Repositionable
Feet (m)
Per Roll
150' (45.8 m)
150' (45.8 m)
100' (30.5 m)
100' (30.5 m)
100' (30.5 m)
100' (30.5 m)
100' (30.5 m)
100' (30.5 m)
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Troubleshooting
Symptom
Cause
Solution
Top and bottom
laminating films are
not aligned.
Cartridge is not
squarely seated.
Reinstall the cartridge making certain
cartridge is seated. Make certain
output tray is completely pushed
forward and down.
Cut blade does not cut
smoothly.
Adhesive build-up on
cutting mechanism.
Using caution, apply adhesive
cleaner to all surfaces of top
blade bar and blade.*
Film does not exit
dispenser between upper
and lower blade bars.
Material is curled or
adhesive has been transferred to the nip roller
causing the film to stick
Remove material and clean
adhesive from rollers if necessary.
Reposition material between
blade bars.*
Film wrinkles don’t
go away as crank is
turned clockwise.
Adhesive build-up on
idler bars.
Apply adhesive cleaner to
remove build-up on idler bars.*
Material does not
laminate or apply
adhesive well.
No pressure between
upper and lower
nip rollers.
Ensure output tray is completely
pushed forward and down.
Laminate will not
advance when crank
handle is turned.
Material is not positioned
between rollers or laminate
is adhered to input tray.
Output tray not seated.
Reinstall cartridge making sure the
output tray is completely pushed
forward and down. Slide input tray
outward to release film and turn handle
to assure laminate is wrinkle-free.
Slide input tray back into machine.
Document wrinkles or
exits machine crooked.
Adhesive build-up on front
edge of input tray or output
tray is not completely
pushed forward and down.
Remove adhesive from front edge
of input tray. Make certain output
tray is completely pushed forward
and down.
*Use Cleaning Kit Xyron #990 for adhesive removal.
THE PURCHASE OR ACQUISITION OF THIS PRODUCT DOES NOT CONFER THE RIGHT OR
LICENSE TO USE THE MACHINE AND CARTRIDGES IN THE RETROREFLECTIVE FIELD OR TO
MAKE OR SELL MACHINES OR CARTRIDGES FOR USE IN THE RETROREFLECTIVE FIELD.
Xyron, Inc. warrants that the Xyron Pro1250 is free from defects in material and workmanship for
a period of one (1) year from the date of purchase. Xyron, Inc. will repair or replace a defective
product or part without charge provided it is returned to the address below, freight prepaid with
proof of purchase. If the product is damaged by neglect or misuse, the warranty is null and void.
Xyron Inc.
15820 N. 84th Street, Scottsdale, AZ 85260
Xyron Europe A/S
Karetma Gervej 27, Fredericia, 7000, Denmark
Xyron Technical Hotline
1-800-793-3523 – USA
+45-7594-5866 – Europe
www.xyron.com
#1445.01
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633PART
3500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising