europower pmh518m
User’s Manual
Version 1.0
November 2005
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
To reduce the risk of electric shock, do not remove
the top cover (or the rear section). No user
serviceable parts inside; refer servicing to qualified
To reduce the risk of fire or electric shock, do not
expose this appliance to rain and moisture. The
apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
This symbol, wherever it appears, alerts you to the
presence of uninsulated dangerous voltage inside
the enclosure—voltage that may be sufficient to
constitute a risk of shock.
This symbol, wherever it appears, alerts you to
important operating and maintenance instructions
in the accompanying literature. Please read the
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
15) CAUTION - These service instructions are for use by
qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than
that contained in the operation instructions unless you
are qualified to do so.
Ultra-Compact 180-Watt 5-Channel Powered Mixer with 24-Bit Multi-FX Processor
and FBQ Feedback Detection System
s Super-compact rackmountable 180-Watt powered mixer with 24-bit FX processor
s Revolutionary amplifier technology: enormous power, incredible sonic performance and super-light weight
s Ultra-compact dimensions at nearly half the depth and weight of conventional powered mixers means no
more lugging around dead weight
s Ultra low-noise ULN design for highest possible headroom and ultra-transparent audio
s 5-channel mixer section comprised of 5 mic/line channels plus separate 2-track in/output
s Integrated 24-bit digital FX processor with 100 awesome presets including reverb, chorus, flanger, delay,
pitch shifter and various multi-effects
s Revolutionary FBQ Feedback Detection System instantly reveals critical frequencies for easy feedback
s 5 high-quality mic preamps with switchable Pad and Clip LEDs
s Effective, extremely musical 2-band EQ on all channels
s 7-band graphic EQ allows precise frequency correction
s 3 speaker outputs on 1/4" jack and professional speaker connectors (compatible to Neutrik® Speakon®)*
s Rack mount brackets included
s High-quality components and exceptionally rugged construction ensure long life
s Conceived and designed by BEHRINGER Germany
* All Trademarks mentioned belong to their respective owners and are not affiliated with BEHRINGER®
Dear Customer,
Welcome to the team of
EUROPOWER users and
thank you very much for
expressing your confidence in BEHRINGER
products by purchasing
this power mixer.
It is one of my most
pleasant tasks to write
this letter to you,
because it is the
culmination of many
months of hard work
delivered by our engineering team to reach a
very ambitious goal:
to present you an
outstanding power mixer
that gives you maximum
flexibility and performance with a unique sound character and
broad range of striking functions.
The task to design the new PMH518M certainly meant a great
deal of responsibility, which we assumed by focusing on you,
the discerning user and musician. It also meant a lot of work and
night shifts to accomplish this goal. But it was fun, too. Developing
a product usually brings a lot of people together, and what a
great feeling it is when everybody who participated in such a
project can be proud of what we’ve achieved.
1. INTRODUCTION ......................................................... 5
1.1 Before you get started ................................................... 5
1.1.1 Shipment ............................................................... 5
1.1.2 Initial operation ...................................................... 5
1.1.3 Online registration ................................................ 5
2. CONTROL ELEMENTS ............................................... 6
2.1 Input channels ................................................................ 6
2.2 Effects section ............................................................... 6
2.3 Main section .................................................................... 6
2.3.1 Connectors ........................................................... 6
2.4 Rear panel ...................................................................... 7
3. DIGITAL EFFECTS PROCESSOR ................................ 7
4. INSTALLATION ........................................................... 7
4.1 Mains connection ........................................................... 7
4.2 Audio connections ......................................................... 7
4.3 Loudspeaker connection ................................................ 8
5. APPLICATIONS .......................................................... 8
6. SPECIFICATIONS ....................................................... 9
7. WARRANTY .............................................................. 10
It is our philosophy to share our joy with you, because you are
the most important member of the BEHRINGER team. With your
highly competent suggestions for new products you’ve greatly
contributed to shaping our company and making it successful. In
return, we guarantee you uncompromising quality as well as
excellent technical and audio properties at an extremely
favorable price. All of this will enable you to fully unfold your
creativity without being hampered by budget constraints.
We are often asked how we can make it to produce such highgrade devices at such unbelievably low prices. The answer is
quite simple: it’s you, our customers! Many satisfied customers
means large sales volumes enabling us to get better conditions
of purchase for components, etc. Isn’t it only fair to pass this
benefit back to you? Because we know that your success is
our success, too!
I would like to thank all people whose help on the PMH518M has
made it all possible. Everybody has made very personal
contributions, starting from the designers of the unit to the many
staff members in our company and finally to you, the user of
BEHRINGER products.
My friends, it’s been worth the trouble!
Thank you very much,
Uli Behringer
We would like to point out that high volume levels
may damage your hearing and/or your loudspeakers.
Please turn the MASTER control fully counterclockwise before switching on the device. Always
make sure that the appropriate volume is set.
1.1.3 Online registration
Congratulations! With the PMH518M you have acquired a stateof-the-art power mixer that sets new standards. Right from the
very start it has been our goal to design a revolutionary unit that
can be used for a wide variety of applications. And indeed, this
overwhelming power mixer gives you plenty of functionality and
a broad range of connection and expansion options.
1.1 Before you get started
1.1.1 Shipment
Your EUROPOWER was carefully packed at the factory and the
packaging is designed to protect the unit from rough handling.
Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage
which may have occurred during transit.
If the unit is damaged, please do NOT return it to
BEHRINGER, but notify your dealer and the shipping
company immediately. Otherwise, claims for
damage or replacement may not be granted.
Please do remember to register your new BEHRINGER equipment
right after your purchase by visiting
(alternatively and kindly read the terms and
conditions of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to have
it repaired as quickly as possible. To arrange for warranty service,
please contact the retailer from whom the equipment was
purchased. Should your BEHRINGER dealer not be located in
your vicinity, you may directly contact one of our subsidiaries.
Corresponding contact information is included in the original
equipment packaging (Global Contact Information/European
Contact Information). Should your country not be listed, please
contact the distributor nearest you. A list of distributors can be
found in the support area of our website (
Registering your purchase and equipment with us helps us
process your repair claims quicker and more efficiently.
Thank you for your cooperation!
We recommend that you use a flight case, so as to
give your power mixer optimum protection during
use or transport.
Always use the original packing carton to prevent
damage during storage or transport.
Make sure that children cannot play unsupervised
with the device or its packaging.
Please ensure proper disposal of all packing
1.1.2 Initial operation
Be sure that there is enough air space around the unit for cooling
and, to avoid overheating, please do not place the EUROPOWER
near radiators, etc.
Blown fuses must be replaced by fuses of the same
“SPECIFICATIONS” for details.
The mains connection is made using the enclosed power cord
and a standard IEC receptacle. It meets all of the international
safety certification requirements.
Please make sure that all units have proper ground
connection. For your own safety, never remove or
disable the ground conductor from the unit or on
the AC power cord.
Fig. 2.1: Front panel control elements and connectors
Press the FBQ IN switch to activate the FBQ Feedback
Detection System. The frequencies causing feedback are
shown by the brightly lit fader LEDs. Simply lower the level
of the respective frequency range until feedback
disappears and the LED goes out.
2.1 Input channels
The HIGH control in the EQ section governs the highfrequency range of the respective channel.
The LOW control allows you too boost/cut the lowfrequency range.
Turn the FX LEVEL control to add effect to the main mix.
When it is fully counterclockwise, no effect signal is added.
The FX control determines the signal level sent from each
channel to the built-in effects processor.
The 2TR LEVEL control adjusts the volume of the 2 Track
In signal (see
Please note that the effects processor signal will
) is set
be inaudible when the FX LEVEL control (
fully counter-clockwise.
Use this 5-digit LED meter to control the output level of the
main signal. The upper LIM LED illuminates when the internal
amp protection circuit responds to output levels that are
too high.
The LEVEL control adjusts the channel signal level in the
main mix.
The MASTER control is used to adjust the main output
The CLIP LED is very useful to control the input gain. It
should never be constantly illuminated (only with signal
2.3.1 Connectors
The PAD switch reduces the input sensitivity of the channel
by approx. 30 dB, to connect for example line-level signals.
The 2TR IN RCA input allows you to feed in external stereo
signals, e.g. from a CD player, tape deck or other line-level
The balanced LINE IN input (1/4" TRS) can be used for
line-level signal sources, e.g. keyboards.
Each channel has a balanced MIC microphone input with
XLR connectors.
Please remember to use either the microphone or
the line input of a channel at a time, but never both
at the same time!
2.2 Effects section
The EFFECT display shows the currently selected preset.
Turn the PROGRAM control to select an effects preset
(preset number starts flashing). Push the control briefly to
confirm your selection.
2.3 Main section
Your power mixer is equipped with a graphic 7-band
equalizer. Use the EQ to adjust the sound to the room
If the REC OUT signal is connected to a recorder
whose output signal is returned to the 2TR IN,
feedback can occur when you activate the record
function. So, disconnect the 2TR IN from the
recorder, before you start recording!
The PMH518M features an AMP INSERT connector for
different applications. You can use just the power stage
of the mixer for connecting a preamp for example. For this
application you can use a 1/4" TS connector where the
signal is sent over the tip of the plug. Additionally you can
use the AMP INSERT as output, so you can use just the
mixer section and connect a separate power amp here.
For this application you have to use a 1/4" TRS connector,
because the signal is send over the ring of the plug.
Be sure that the CLIP LED illuminates for signal peaks only.
If it is illuminated all the time, it is a sign that the effects
processor is overloading and hence producing unpleasant
distortion. The SIG LED below illuminates when the effects
processor receives an input signal.
Press the FX IN button to activate the effects processor.
The REC OUT (RCA) provides line-level signals from the
power mixer to a DAT recorder, for example (two identical
mono signals).
Use the POWER switch to put the unit into operation. The
POWER switch should always be in the “Off” position when
you are about to connect the unit to the mains.
Please note: The POWER switch does not fully
disconnect the unit from the mains. Unplug the
power cord completely when the unit is not used
for prolonged periods of time.
Fig. 2.2: Rear panel control elements and connectors
2.4 Rear panel
The mains connection is on a standard IEC receptacle. An
appropriate power cord is supplied with the unit.
FUSE HOLDER. Before connecting the unit to the mains,
ensure that the voltage setting matches your local voltage.
Blown fuses should only be replaced by fuses of the same
type and rating. Please also read the information given in
The three PARALLEL SPEAKER OUTPUTs provide the
mono main signal on a Neutrik ® Speakon ®-compatible
connector (pins 1+/1- and 2+/2-) and on two
1/4" TS connectors.
4.1 Mains connection
Blown fuses must be replaced by fuses of the same type and
The mains connection is made using the enclosed power cord
and a standard IEC receptacle. It meets all of the international
safety certification requirements.
The impedance of the loudspeaker connected must
not fall below 4 W.
Information on how to properly connect your
speaker with regard to polarity can be found on the
rear of the mixer (PINOUTs).
This is the cooling fan of the unit.
The PMH518M features a built-in digital stereo effects processor.
This effects processor offers a large number of standard effects
such as Hall, Chorus, Flanger, Delay and various combination
effects. Using the FX control, you can feed signals into the
effects processor. The integrated effects module has the
advantage of requiring no wiring. This way, the danger of creating
ground loops or uneven signal levels is eliminated at the outset,
completely simplifying the handling.
Presets 00 - 09:
Presets 10 - 19:
Presets 20 - 29:
Presets 30 - 39:
Presets 40 - 49:
Early Reflections
Presets 50 - 59:
Presets 60 - 69:
Presets 70 - 79:
Presets 80 - 89:
Multi 1
Presets 90 - 99:
Multi 2
Please make sure that all units have a proper
ground connection. For your own safety, never
remove or disable the ground conductor from the
unit or of the AC power cord.
4.2 Audio connections
The inputs and outputs of the BEHRINGER EUROPOWER are
unbalanced 1/4" TS connectors—except for the balanced mono
line inputs and the balanced XLR inputs. Of course, all inputs and
outputs work with both balanced and unbalanced connectors.
The Tape Ins and Outs are on RCA connectors.
Please ensure that only qualified personnel install
and operate the power mixer. During installation
and operation, the user must have sufficient
electrical contact to earth. Electrostatic charges
might affect the operation of the unit.
Fig. 4.1: 1/4" TS connector
Please be sure to only use commercial Speakon® cables (type
NL4FC) for connecting your loudspeakers to the mixer. Please
check the pin connections of your loudspeakers and cables
depending on the EUROPOWER speaker output you choose.
Tab. 4.1: Pin connections of the professional loudspeaker
Fig. 4.2: 1/4" TRS connector
This illustration shows just one example of how the channels of
your power mixer can be used, including the connection of mono
and stereo sources, and the tape ins and outs recording the mix
signal or playing back external signals.
Fig. 4.3: XLR connectors
Fig. 4.4: RCA cable
4.3 Loudspeaker connection
Your EUROPOWER is equipped with high-quality Neutrik ®
Speakon®-compatible loudspeaker connectors, which ensure
safe and trouble-free operation. The Speakon® connector was
especially developed for high-power loudspeakers. Once it is
plugged in, it safely locks into position and cannot be accidentally
disengaged. It prevents the occurrence of electrical shock and
ensures the correct polarity. Each of the connectors carries
only the assigned single signal (see tab. 4.1/fig. 4.5 and the
information on the rear panel of the power mixer).
Fig. 5.1: Standard set-up
Fig. 4.5: Loudspeaker connector
The following illustration shows a live application with the
PMH518M as monitor mixer and a BEHRINGER EURODESK
SL2442FX-PRO that provides the FOH main mix signal. The
PMH518M receives the Aux Send signal of the EURODESK that
is used for the monitor mix on stage.
Mic E.I.N. (20 Hz - 20 kHz)
@ 0 W source resistance
@ 50 W source resistance
@ 150 W source resistance
Frequency response
Max. input level
Signal-to-noise ratio
Distortion (THD+N)
XLR, electronically balanced
-122 dB / -125 dB A-weighted
-122 dB / -125 dB A-weighted
-121 dB / -124 dB A-weighted
< 10 Hz - 100 kHz (-1 dB),
< 10 Hz - 200 kHz (-3 dB)
+33 dB, +8 dB with pad
+12 dBu @ 10 dB gain
approx. 2.2 kW balanced,
1.1 kW unbalanced
110 dB / 114 dB A-weighted
(-11 dBu in @ +33 dB gain)
0.001% / 0.0008% A-weighted
Max. input level
1/4" TRS connector, balanced
approx. 80 kW balanced,
40 kW unbalanced
+30 dBu
80 Hz / ±15 dB
12 kHz / ±15 dB
Main mix @ -oo,
Channel fader -oo
Main mix @ 0 dB,
Channel fader -oo
Main Mix @ 0 dB,
Channel fader @ 0 dB
-106 dB / -110 dB A-weighted
-87 dB / -90 dB A-weighted
-80 dB / -82 dB A-weighted
Load impedance
Neutrik® Speakon®-compatible,
1/4" TS connectors
4 - 16 W
Sampling rate
24-bit Sigma-Delta,
40 kHz
2-digit, 7-segment LED
Output power @ 4 W
Output power @ 8 W
1 x 180 W
1 x 100 W
Mains voltages
Fig. 5.2: Setup with PMH518M as monitor mixer
Power consumption
Mains connection
Dimensions (H x W x D)
Weight (net)
120 V~, 60 Hz
220 V~, 50 Hz
230 V~, 50 Hz
100 V~, 50 - 60 Hz
General export model
120/230 V~, 50 - 60 Hz
max. 300 W
100 - 120 V~: T 2.5 A H 250 V
220 - 240 V~: T 5 A H 250 V
Standard IEC receptacle
approx. 4 3/5" (117 mm)
x 18 1/2" (470 mm)
x 8 9/8" (225 mm)
approx. 15.88 lbs (7.2 kg)
BEHRINGER is constantly striving to maintain the highest professional standards. As a result
of these efforts, modifications may be made from time to time to existing products without prior
notice. Specifications and appearance may differ from those listed or illustrated.
1. This warranty does not exclude or limit the buyer’s statutory
rights provided by national law, in particular, any such rights
against the seller that arise from a legally effective purchase
2. The warranty regulations mentioned herein are applicable
unless they constitute an infringement of national warranty law.
2. If the product needs to be modified or adapted in order to
comply with applicable technical or safety standards on a national
or local level, in any country which is not the country for which
the product was originally developed and manufactured, this
modification/adaptation shall not be considered a defect in
materials or workmanship. The warranty does not cover any
such modification/adaptation, irrespective of whether it was
carried out properly or not. Under the terms of this warranty,
BEHRINGER shall not be held responsible for any cost resulting
from such a modification/adaptation.
Please do remember to register your new BEHRINGER equipment
right after your purchase by visiting
(alternatively and kindly read the terms and
conditions of our warranty carefully.
3. Free inspections and maintenance/repair work are expressly
excluded from this warranty, in particular, if caused by improper
handling of the product by the user. This also applies to defects
caused by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, tubes, guitar strings,
illuminants and similar parts.
Registering your purchase and equipment with us helps us
process your repair claims quicker and more efficiently.
4. Damages/defects caused by the following conditions are not
covered by this warranty:
Thank you for your cooperation!
improper handling, neglect or failure to operate the unit in
compliance with the instructions given in BEHRINGER user
or service manuals.
connection or operation of the unit in any way that does
not comply with the technical or safety regulations
applicable in the country where the product is used.
damages/defects caused by force majeure or any other
condition that is beyond the control of BEHRINGER.
1. BEHRINGER (BEHRINGER International GmbH including all
BEHRINGER subsidiaries listed on the enclosed page, except
BEHRINGER Japan) warrants the mechanical and electronic
components of this product to be free of defects in material and
workmanship for a period of one (1) year* from the original date
of purchase, in accordance with the warranty regulations
described below. If the product shows any defects within the
specified warranty period that are not excluded from this
warranty as described under § 5, BEHRINGER shall, at its
discretion, either replace or repair the product using suitable
new or reconditioned parts. In the case that other parts are used
which constitute an improvement, BEHRINGER may, at its
discretion, charge the customer for the additional cost of these
2. If the warranty claim proves to be justified, the product will be
returned to the user freight prepaid.
3. Warranty claims other than those indicated above are expressly
5. Any repair or opening of the unit carried out by unauthorized
personnel (user included) will void the warranty.
6. If an inspection of the product by BEHRINGER shows that the
defect in question is not covered by the warranty, the inspection
costs are payable by the customer.
7. Products which do not meet the terms of this warranty will be
repaired exclusively at the buyer’s expense. BEHRINGER will
inform the buyer of any such circumstance. If the buyer fails to
submit a written repair order within 6 weeks after notification,
BEHRINGER will return the unit C.O.D. with a separate invoice
for freight and packing. Such costs will also be invoiced
separately when the buyer has sent in a written repair order.
1. To obtain warranty service, the buyer (or his authorized dealer)
must call BEHRINGER (see enclosed list) during normal business
hours BEFORE returning the product. All inquiries must be
accompanied by a description of the problem. BEHRINGER will
then issue a return authorization number.
2. Subsequently, the product must be returned in its original
shipping carton, together with the return authorization number to
the address indicated by BEHRINGER.
3. Shipments without freight prepaid will not be accepted.
1. Warranty services will be furnished only if the product is
accompanied by a copy of the original retail dealer’s invoice.
Any product deemed eligible for repair or replacement under the
terms of this warranty will be repaired or replaced.
This warranty is extended exclusively to the original buyer
(customer of retail dealer) and is not transferable to anyone
who may subsequently purchase this product. No other person
(retail dealer, etc.) shall be entitled to give any warranty promise
on behalf of BEHRINGER.
Failure of BEHRINGER to provide proper warranty service shall
not entitle the buyer to claim (consequential) damages. In no
event shall the liability of BEHRINGER exceed the invoiced value
of the product.
* Customers in the European Union please contact BEHRINGER
Germany Support for further details.
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of printing. The names
of companies, institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners. Their use
neither constitutes a claim of the trademarks by BEHRINGER® nor affiliation of the trademark owners with BEHRINGER®. BEHRINGER® accepts no
liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained
herein. Colours and specification may vary slightly from product. Products are sold through our authorised dealers only. Distributors and dealers are not
agents of BEHRINGER® and have absolutely no authority to bind BEHRINGER® by any express or implied undertaking or representation. No part of this
manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for
any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER® is a registered trademark.
ALL RIGHTS RESERVED. © 2005 BEHRINGER Spezielle Studiotechnik GmbH,
Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF