Installation and O peration M anual

Installation and O peration M anual
Water Purifier
How to install, operate and maintain your
Microbiological Drinking Water Purifier
System tested and certified to meet the
requirements of NSF Protocol P231 and
NSF/ANSI Standards 42 & 53.
See performance data sheet for details.
Manufactured by Pelican Water Systems
3060 Performance Circle, Suite 2, DeLand FL 32723
Toll Free (877) 842-1635
Rev Date 3/11/2016
Installation and Operation Manual
Model PDF-1000VF
TABLE OF CONTENTS
Page
What the Microbiological Drinking Water Purifier Will Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications & Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Parts of the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Materials & Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Step 1 – Installing the Saddle Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 2 – Selecting the Faucet Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 3 – Mounting the Faucet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 4 – Mounting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 5 – Connecting the Faucet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 6 – Attaching Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 7 - Connecting the Saddle Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 8 – Connecting the Inlet Line to System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 9 – Setting the Effective Life Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 10 – Putting the System into Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Filter Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Filter Cartridge Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Filter Cartridge Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Exploded View & Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WARRANTY
ONE YEAR LIMITED WARRANTY ON MICROBIOLOGICAL DRINKING WATER PURIFIER
Warrantor: Pelican Water Systems, 3060 Performance Circle, Suite 2, DeLand FL 32723
Pelican Water Systems warrants to the original owner (under normal use): all products and parts to be free from defects in material and workmanship for a period of one (1) year
from the date of purchase. Any replacement products furnished will be free from defects in material and/or workmanship for the remainder of the original warranty period or 30
days, whichever is longer. This warranty does not cover: (1) defects not reported within the above time period, (2) problems arising from failure to comply with Pelican Water
Systems instructions, (3) problems and/or damage arising from acts of nature, abuse, misuse, negligence or accident by any party other than Pelican Water Systems, (4) problems
and/or damage resulting in whole or in part from alteration, modification, repair or attempted alteration, modification or repair by any party other than Pelican Water Systems, (5)
noncompliance with applicable codes/ordinances.
If a defect in workmanship and/or material in a product or part covered by the warranty should arise, Pelican Water Systems, at its sole discretion, will repair or replace the defective
product or part (Pelican Water Systems will consider the customer’s preference in good faith).
All claimed defective product must: (1) be authorized for return by Pelican Water Systems with an RGA number (2) include proof of the purchase date of the product or part (3)
returned to Pelican Water Systems prior to the expiration of the warranty date at the customer’s expense, shipment pre-paid (4) be accompanied by a letter detailing the Model
Number, Serial Number (if any), and a brief description of the problem.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, PELICAN WATER SYSTEMS DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCTS, PARTS AND ANY ACCOMPANYING
WRITTEN MATERIALS.
To the maximum extent permitted by applicable law, Pelican Water Systems shall not be liable for any damages whatsoever (including, but not limited to, loss of time, inconvenience,
expenses, labor or material charges incurred in connection with the removal or replacement of the products or parts, special, incidental, consequential, or indirect damages for
personal injury, loss of business profits, business interruption, loss of business information, or any other pecuniary loss) arising out of the use of or inability to use the defective
products or parts even if Pelican Water Systems has been advised of the possibility of such damages.
Pelican Water System’s maximum liability under any provision of this Limited Warranty shall be limited to the amount actually paid for the products or parts.
This warranty is effective if the Pelican Water Purifier is operated at water pressured between 30-100 psig and a water temperature between 40-100°F. Furthermore, the purifier
must not be subject to mistreatment, system modification, disregard, freezing, carelessness, or damage as a result of any unusual force of nature (i.e. hurricane, flood, earthquake, or
tornado). Warrantor is excused if failure to perform its warranty obligations is the result of material shortages, government regulation, strikes, or any other circumstances beyond its
control.
What the Drinking Water Purifier Will Do
The PDF-1000VF is a water purification treatment system. This system uses a triple filter design to reduce unwanted elements in your
drinking water. Possible elements may include chlorine, lead, virus, bacteria, cysts, particulates and numerous organic compounds.
The PDF-1000VF utilizes the patented NanoCeram® and other technologies in a systematic approach to ensure the water supply conforms
to EPA Guide Standard for the removal of 99.9999% Bacteria, 99.99% Viruses, and 99.95% Cysts. The PDF-1000VF is designed to
discontinue water flow when its capability to filter unwanted elements has been exhausted. This will help safeguard the consumer against
contaminated water. Replace all filters every 6 months or 1000 gallons.
NOTE: A performance data sheet is included and lists what elements will be reduced from the water supply. (Please note that not all
elements may be present.) This data sheet lists the individual contaminants and microbial reduction performance.
The drinking water purifier system is designed to fit under the kitchen or bathroom sink or any other area that is suitable. A COLD water
supply pipe is required within a few feet. If water supply pipe is farther than what the tube will reach, you can purchase longer lengths of
tubing from your local home improvement center.
NOTE: Make sure the tubing is acceptable for use on potable water supplies.
Before You Start










In order to receive all of the benefits of your microbiological drinking water purifier, be sure to read all steps in this guide
carefully and follow steps exactly.
This system is intended for use with municipal and/or well-supplied water only. It is not intended for use with surface water such as
from a lake or runoff.
Do not use for the treatment of water that is visually contaminated (cloudy) or has an obvious contamination source, such as
contamination by raw sewage.
Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
System is not intended to convert wastewater or raw sewage into drinking water.
Installation and plumbing should comply with all local laws and regulations. Consult with your licensed plumber.
NOTE: In Massachusetts, plumbing code 248 CMR 3.00 and 10.00 shall be adhered to.
The microbiological drinking water purifier works on water pressure of 30 psig (minimum) to 100 psig (maximum). If your house
water pressure is over the maximum, install a pressure reducing valve in the water supply pipe to the filter system.
Do not install the microbiological drinking water purifier outside, or in extreme hot or cold temperatures. Temperature of the
water supply to the under-sink drinking water filter system must be between 40◦F and 100◦F. Do not install on hot water.
Do not use with water that is microbiologically unsafe or of unknown quality without disinfection before or after the system.
Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Precautions
•
•
•
•
This system is for “cold water” use only.
Protect filters against freezing, which can cause cracking of the filter and water leakage.
The rubber O-ring provides the water-tight seal between the cap and the bottom of the housing. It is important that the
O-ring be properly seated in the groove below the threads of the housing or a water leak could occur.
To prevent costly repairs or possible water damage, the sump of plastic housings must be replaced every ten years. If sump is
older than recommended, replace immediately. Date sump for reference and indicate replacement date.
Specifications & Dimensions
Supply Water Pressure . . . . . . . . . . 30 – 100 psig
Min - Max
(2.1-6.7 bar)
Supply Water Temperature . . . . . . . . 40 - 100◦F
Min. – Max.
(4.4 – 37.8◦C)
Service Flow Rate
@60 psig . . . . . . . . . . . . . . . (0.5 GPM @4.1 bar)
Rated Service Life . . . . . 1000 gallons (3,785 L)
Dimensions . . . . . . . . . . 15.5” H x 5.25” D x 14” L
(394mm x 133mm x 356mm)
Weight . . . . . . . . (filled with water) 19lbs (8.6kg)
3
Parts of the System
● Filter system with filter cartridges
● Installation hardware (mounting screws, saddle valve, flow restrictor, fittings)
● 1/4-inch (6.35mm) tubing
● Lead-free faucet
Materials and Tools Needed
Note: Gather the required tools before starting installation. Read and follow the instructions
•
•
•
•
•
•
provided with any tools listed here.
Safety glasses
Hand or electric drill (cordless recommended)
File or sandpaper
Phillips Head screwdriver
2 adjustable wrenches
Tube cutters or utility knife
**If sink does not have hole for separate faucet:
•
•
•
Center punch
3/4-inch (19mm) drill bit
Masking tape
IMPORTANT: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures in
porcelain, granite, or stainless steel.
Installation Instructions
NOTE:
NOTE:
NOTE:
NOTE:
A squeaking sound when tightening a compression nut is normal.
If fittings are removed, Teflon® tape must be used for pipe threaded connections.
Be sure to wear safety glasses when using a drill.
Typical faucet shown. Faucet will vary.
•
•
System is designed for standard under-sink installation on 3/8”-inch (10mm) cold water line.
Numbered diagrams correspond with numbered steps.
Step 1 – Installing the Saddle Valve
Use of a cordless drill is recommended. To protect yourself from serious injury or fatal
shock when using an electric drill, be sure the drill and the outlet it is plugged into are
properly grounded. When using a drill, follow the manufacturer’s guidelines and procedures.
NOTE: Saddle valve must be installed on a 2-inch (51mm) long, straight-walled section of
3/8-inch to 7/8-inch (10-22mm) steel, brass, copper, or PVC pipe
a) Turn off cold water supply and turn on nearest faucet before starting installation.
Place a tray or towels under the cold water line to catch excess water.
b) Drill a 1/8-inch (3mm) hole in the cold water line. Remove any burrs with sandpaper
or file.
c) Turn handle on the saddle valve to expose lance no more than 3/16-inch (5mm)
above black rubber gasket.
d) Place valve body over hole in cold water line so lance fits into hole.
e) Attach back plate of clamp and tighten bolts evenly and firmly so brackets are parallel.
f) Turn valve handle clockwise to closed position and leave closed until installation is compete.
NOTE: All nuts must be retightened when the system reaches projected operating temperature.
4
Installation Instructions
Step 2 – Selecting the Faucet Location
NOTE: The drinking water faucet should be positioned with function, convenience, and
appearance in mind. An adequate flat area is required to allow faucet base to rest securely.
The faucet fits through a 3/4-inch (19mm) hole. Most sinks have pre-drilled 1-inch (35 or 38mm)
diameter holes that may be used for faucet.
a) Line bottom of sink with newspaper to prevent metal shavings, parts, or tools from
falling down drain.
b) Place masking tape over the area to be drilled to prevent scratches if drill bit slips.
IMPORTANT: To avoid damaging the sink, consult a qualified plumber or installer for drilling
procedures in porcelain, granite, or stainless steel.
c) Mark hole with center punch. Use a 1/4-inch (6mm) drill bit for a pilot hole, then,
using a 3/4-inch (13mm) drill bit or hole saw, drill a hole completely through the sink.
Smooth rough edges with a file.
Step 3 – Mounting the Faucet
a) Locate the faucet installation packet.
b) Slide the escutcheon plate then the rubber gasket onto the threaded shaft of the faucet.
c) Slide the threaded shaft of the faucet into the drilled hole.
d) From under the sink, slide the large washer and lock washer on the threaded shaft.
e) Thread on the lock nut. Tighten lock nut by hand until tight.
Caution: Do not over-tighten the lock nut. Hand tighten only. Do not use pliers or
wrench to tighten.
Step 4 – Mounting the system
a)
Center system between water supply adapter and drinking water faucet.
NOTE: Allow 1.5 inches (38mm) clearance below system to enable filter
cartridge changes.
NOTE: In the following step, leave enough space (approximately 1/2-inch (13mm))
between the head of the screw and the wall to easily slip system into place.
b)
Install mounting screws at least 15-inches (380mm) from cabinet floor and
9 1/4-inches (235mm) apart. Place system over screws on wall and slide sideways.
Tighten screws.
Caution: Make certain system is firmly attached to wall to prevent possible damage from
falling.
Step 5 – Connecting Tubing to the Faucet
Caution: Do not over-tighten compression nut. Use caution not to bend or crimp tubes when securing.
a) Locate compression nut pieces (3) in installation kit and faucet package.
b) Attach compression nut pieces (3) to one end of tubing by sliding the nut and ferrule onto the
tubing; then insert the sleeve into the tube.
c) Attach tube with compression nut assembly to faucet stem by inserting tube into the faucet
stem opening. Tighten nut.
NOTE: All nuts must be retightened when the system reaches projected operating temperature.
5
Installation Instructions
Step 6 – Attaching Tube to Effective Life Indicator (ELI)
a)
Determine the length of tubing needed from the faucet to the ELI. A slight sag in the
line will allow for some ease in installation. Cut the tubing to required length.
b) Insert other end of tubing firmly into the outlet port (John Guest® fitting) of the ELI
until fully engaged.
c) Pull tube gently to ensure the tubing is fully seated.
Caution: Tube must be fully inserted in the compression fitting base on the outlet stem of the ELI.
Step 7 – Connecting the Saddle Valve
a)
Determine the length of plastic tubing needed to connect the inlet (left) side of the filter
with the saddle valve. Be sure to allow enough tubing to prevent kinking and cut the tubing
squarely. Slide brass compression nut onto tubing, followed by plastic ferrule. The long tapered
end of the ferrule should face towards the end of the tubing. Place insert into tubing.
b) Insert tubing into saddle valve and hand-tighten compression nut. Using a wrench, tighten nut
1 to 1 ½ turns.
NOTE: All nuts must be retightened when the system reaches projected operating temperature.
Step 8 – Connecting Inlet Line to System
a) Insert other end of tubing firmly into inlet port (John Guest® fitting) until fully engaged.
b) Pull tube gently to ensure the tubing is fully seated.
Step 9 – Setting the Effective Life Indicator
NOTE: The effective life indicator is the white dial located on the center of the mounting bracket.
Each black mark on the dial represents 100 gallons (378.5L).
a) Move the dial clockwise so that the black indicator arrow lines up with the 1100 gallon
(4,164 L) mark.
Important: Set flow meter to 1100 gallons after each new filter replacement.
NOTE: To prevent indicator malfunctions, only move the dial when the system is depressurized.
NOTE: Based on the settings sensitivity of the Effective Life Indicator (ELI), user should set the
ELI to 1,100 gallons to assure a 1,000 gallon cycle.
Step 10 – Putting the System into Operation
a) Slowly turn on cold water supply.
b) Rotate handle on base of drinking water faucet counter-clockwise to “ON” position.
Allow water to run for 10 minutes to flush air and carbon fines from filter cartridges.
Check system for leaks before completing installation.
c) Make sure that all nuts are tightened.
NOTE: A drinking water cartridge may contain carbon fines (very fine black powder). It is
recommended that you run the tap at least 20 seconds prior to using water for drinking or
cooking purposes.
NOTE: Initially, filtered water may appear cloudy. If you set a glass of water on a level surface, you
should be able to watch the cloudiness disappear from the bottom of the glass upwards. This harmless cloudiness
results from the release of trapped air with the cartridge and will disappear within a few weeks after installation.
INSTALLATION IS NOW COMPLETE.
6
Filter Cartridges
Filter Cartridge Life
It is recommended to replace filter cartridges every six months or 1000 gallons of use. However, your water quality can
lead to circumstances such as diminished water flow, visible sediment, or unwanted taste and/or odor in your water,
requiring the cartridges be replaced sooner.
There are several variables that determine how long a cartridge will last.
These include:
1.
2.
How much water you use, and
How much sediment, chlorine, or other unwanted substances is in the water.
Filter Cartridge Replacement
NOTE: Contact your system supplier for replacement filter parts.
1.
2.
3.
Turn off cold water supply to system and turn on faucet to release pressure.
NOTE: Due to water leakage, place a pan or towel under sump.
Unscrew and remove bottom of filter housing. Locate and remove large O-ring, wipe clean of lubricant, and set aside.
Repeat for second and third housings.
Discard used filter cartridges.
Caution: Read “WARNING” information on the bleach container before using.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Using a non-abrasive sponge or cloth, scrub the bottom of each housing, O-ring grooves, and caps with dish soap and
warm water. Rinse thoroughly. Then fill bottom of each housing 1/3 full with water. Add 1TBSP (14.7ML) of
household bleach and scrub to disinfect.
.
Lubricate O-rings with clean silicone grease. Insert each O-ring in groove and press into place.
NOTE: This step is important to ensure a proper housing seal. Make certain each O-ring is seated level in its groove or
a leak may occur.
Screw bottom of housing(s) with bleach water onto cap(s) without filter cartridge(s) and hand-tighten. DO NOT OVERTIGHTEN.
Turn on water supply. Let faucet run for about 10 seconds, then turn off faucet and let stand for 20-30 minutes.
Turn on faucet and allow bleach water to run out (about 3-5 minutes)
Turn off water supply to system. Remove bottom of housings and empty out water.
Insert each filter cartridge in bottom of appropriate filter housing.
IMPORTANT: Be sure to remove any protective covering from the filters before inserting.
Screw bottom of housing(s) onto cap(s) and hand-tighten. DO NOT OVER-TIGHTEN. Make certain cap standpipe slips
into cartridge(s).
Reset effective life indicator to 1100 gallons (see instruction under “Setting Effective Life Indicator” on Page 6.)
NOTE: Based on the setting sensitivity of the Effective Life Indicator (ELI), user should set the ELI to 1,100 gallons to
assure a 1,000 gallon cycle.
Turn on water to system. Let faucet run for 10 minutes to remove trapped air and carbon fines. Check system for
leaks.
REPLACEMENT FILTERS
PDF-VF-R01 NanoCeram® Filter
PDF-VF-R02 Fiberdyne® Filter
PDF-VF-R03 Deal® Block Filter
7
Troubleshooting the System
Problem:
Leaks between cap and bottom of filter housing
Correction:
Turn off water supply and turn on drinking water faucet to release pressure in
system. Remove bottom of housing. Clean O-ring groove (located directly
beneath threads of housing). Lubricate O-ring with silicone grease and replace
securely into groove. Screw bottom of housing onto cap and hand-tighten. DO
NOT OVER-TIGHTEN. Turn on water supply and check for leaks
Problem:
Leaks on system inlet/outlet connections
Correction:
Turn off water supply and turn on drinking water faucet to release pressure in
system. Remove tubing from fitting and make sure end of tubing is cut squarely
and free of burrs. Reinsert tubing into fitting, making sure to push tubing to a
hard stop. Hand-tighten compression nut first, then tighten 1 to 1 1/2 turns for
new compression nut. Tighten only 1/2 to 1 turn with wrench for previously
tightened compression nut.
NOTE: If leaks persist, or if there are other leaks in system, turn off water supply.
Problem:
Leaks on faucet / tubing connection
Correction:
Turn off water supply and turn on drinking water faucet to release pressure in
system. Loosen and remove compression nut fitting on faucet stem. Make sure
tubing is inserted firmly into end of faucet stem, then retighten compression nut
with fingers until secure. Turn on saddle valve, and then turn off faucet to check
for leaks.
NOTE: If leaks persist, or if there are other leaks in system, turn off water supply.
Problem:
No water or decreased water flow.
Correction:
Check flow at faucet. The PDF-1000VF system should fill a gallon jug in
approximately 2 minutes. Flow rates will vary with individual household water
pressure.
Correction:
Check filter cartridge installation. Make certain all filter cartridges are properly
oriented in filter housings.
Correction:
Replace filter cartridges.
Parts List
ITEM#
QTY
PART#
1
4002991
DESCRIPTION
ITEM#
QTY
PART#
15
1
PDF-VF-R03
FILTER, DEAL®
DESCRIPTION
CARTRIDGE , FIBERDYNE®
1
144169-02
MTG BRACKET, 3 HOUSING WHITE
MTG BRACKET, 3 HOUSING WHITE
(ALTERNATIVE)
16
1
PDF-VF-R02
2
2
SH244788
ELBOW, 1/4" NPT X 1/4" QC WH PP
17
1
PDF-VF-R01
3
2
SH244791
NIPPLE, MALE HEX 1/4" NPT X 1/4" NPT
20
2
161123
FILTER TIMER MONITOR, 12 MONTH
4
3
158125
1/4" #10 SL WHITE WO/PR 12/C
21
161125
INSTRUCTION SHEET, TIME STRIP
5
4
SH143263
SCREW #6X 1/4" LG PHIL PAN
22
1
0.0240
RL
6
1
42561
LUBRICANT, SILICONE, PACKET
25
1
7
1
150539
WRENCH SW-1A
26
1
10.000
FT
8
12
PW-80-09
SCREW, #10 - 32 X 3/4" PAN HEAD
27
2
9
1
4002987
VALVE, SADDLE 1/4 COMPRESSION
24
10
2
SH243249
SCREW #10-12 X 1.5 TYPE A
32
11
3
C143026
LOCAL "O-RING"
33
0.1250
FT
0.4583
FT
13
1
701-DBXX
FAUCET
34
1
14
1
161127
METER, 1800 GALLON, 1/4 NPT
8
FILTER, NANOCERAM®
SH144223
MACHINE TAPE, TEFLON 1/4" WIDE
1611161
MANUAL, PELICAN PDF-1000VF
SH243244
TUBE, 1/4" OD WHITE PE
161143
DM FITTING; 1/4" X 1/4" QC; NPT
N/A
SH243244
TUBE, 1/4" OD WHITE PE
SH243244
TUBE, 1/4" OD WHITE PE
244985
INLINE FLOW RESTRICTOR, 0.5 GPM
EXPLODED PARTS VIEW
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising