SMM601 - InterMotive
An ISO 9001:2008 Registered Company
SMM601 Surveillance Mode Module
2015-2016 Chevy Tahoe (PPV - Police Vehicle)
Introduction
The SMM601 for Chevy Tahoe uses the vehicle’s OEM Back up sensors and camera to inform an
officer if anyone is behind the vehicle. Anytime Surveillance Mode is active, the reverse sensors
will be turned on. If any of the sensors are tripped while in Surveillance mode, the system will
turn on the Rear View Display, a chime will activate indicating a sensor has been tripped, all the
door’s will lock, the driver’s window will roll up, and the reverse lights will turn on.
Installation Instructions
Disconnect vehicle battery before proceeding with installation
IMPORTANT - READ BEFORE INSTALLATION
It is the installer’s responsibility to route and secure all wiring harnesses where they cannot be
damaged by sharp objects, mechanical moving parts and high heat sources. Failure to do so could
result in damage to the system or vehicle and create possible safety concerns for the operator and
passengers.
It is important to avoid placing the module where it could encounter strong magnetic fields from
high current cabling connected to motors, solenoids, etc. Also avoid radio frequency energy from
antenna’s or inverters next to the module. Finally, avoid high voltage spikes in vehicle wiring by
always using diode clamped relays when installing upfitter circuits.
SMM601 Module
Remove the lower dash panel below the steering column area and find a suitable location to mount
the SMM module. Locate the module in an area away from any external heat sources (engine heat,
heater ducts, etc.). Do not mount the module until all wire harnesses are routed and secure. The
last step is to mount the module.
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 1 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-INS
16w Minifit Jr (Red Jumpers)
Connect S-H30EX red wire connector into 16-pin connector.
WARNING DO NOT USE BLACK WIRE JUMPER VERSION!
16 Pin Connector Connector
4w Minifit Jr
Pin #1 - Green/White wire to momentary low true input to enable
Surveillance mode. (momentary switch not included in kit)
Pin #2 - Not Used
Pin #3 - Not Used
4 Pin MiniFit Connector
Pin #4 - Not Used
4W SABRE Outputs for Rear Lights
Surveillance mode will provide 12 Volt Outputs Rated at
2 Amps each.
SMM Outputs
Pin 1: SMM Enabled Output (Yellow Wire)
4 Pin Sabre Connector
Pin 2: SMM Tripped Output (Orange Wire)
Pin 3: Shift Lock Solenoid Output (Blue Wire)
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 2 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-INS
4W SABRE Pin-out Definition
This connector contains the Surveillance Mode output pins. Each output is rated at 2A and is intended
to drive low current loads.
SMM Outputs
Pin 1: SMM Enabled Output (Yellow Wire)
Pin 2: SMM Tripped Output (Orange Wire)
Pin 3: Shift Lock Solenoid Output (Blue Wire)
4 Pin Sabre Connector
Output Installation
SMM Enabled Output
This output will be active when Surveillance Mode is enabled. This is intended to drive an LED to
inform the user the module is in Surveillance Mode. The LED is not included in kit. All preconditions
must be met before activating Surveillance Mode. Refer to page 6.
SMM Tripped Output
This output will be active when one of the OEM back up sensors are tripped when in Surveillance
mode. This is intended to drive LED’s, the light bar, or other vehicle equipment.
Installation of Shift Lock Solenoid Harness
1. Remove the lower steering column trim cover.
2. Locate the OEM shift lock solenoid to the right side of the steering
column.
3. Remove the OEM 2-pin black connector.
4. Locate the Black T-harness Blue wire Pin 3 of the 4 pin connector.
5. Plug the Black connectors into the Shift Lock Solenoid.
6. Verify locking tabs are in the locked position.
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 3 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-INS
Surveillance Mode Post Installation Instructions
Preferably test with two people so one person can activate the rear sensors.
1. Place car in Park, close the driver door, and do not apply the Service Brake.
2. Put the driver and passenger door windows all the way down and unlock doors.
3. Apply Surveillance Mode input.
4. Have one person trip the sensors by walking behind the vehicle.
5. Verify that the window goes up, all doors lock, and the reverse ‘back-up’ lights flash.
6. Verify rear camera display turns on.
7. Open driver door to exit surveillance mode and verify rear camera turns off and the reverse
lights shut off.
If the SMM601 fails any step in the Post Installation Test, call InterMotive Technical
Support at (530) 823-1048.
SMM601 Module Mounting
Ensure all harness are properly connected and routed, and are not hanging below the dash area.
Mount the SMM601 module using screws or double sided tape. Reinstall the lower dash panel.
Data Link Harness
1. Locate the vehicle OBDII Data Link Connector. It will be mounted below the lower left dash panel.
2. Remove the mounting screws for the OBDII connector. Plug the Red
connector from the SMM601 Data Link Harness into the vehicle’s
OBDII connector. Ensure the connection is fully seated and secure
the connectors together with the supplied wire tie.
3. Mount the Black pass-through connector from the SMM601 Data Link
Harness in the former location of the vehicle’s OBDII connector.
4. Secure the SMM601 Data Link harness so that it does not hang below the lower dash panel.
5. Plug the free end of the Data Link harness into the mating 6-pin connector on the SMM601 module.
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 4 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-INS
The Chevy Tahoe has an Auto Lock/Unlock feature that will control the door lock when shifting in
and out of Park. This feature must be turned off for Surveillance mode to function properly.
Removing Auto Door Lock/Unlock
1. Press the “Home Button”.
2. Scroll to the Settings tab using the Menu Wheel and press the “Menu” button to enter.
3. Scroll to the “Vehicle” tab and press “Menu” to enter.
4. Enter “Power Door Locks” , then “Auto Door Locks” and select “OFF”.
5. Press “Back button” to return to previous menu.
6. Scroll to “Auto Door Unlocks” and press “Menu” to enter. Then select “OFF”.
7. Shift in and out of park and verify door locks aren't automatic.
Home Buon
Menu Wheel
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 5 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-OP
Surveillance Mode
2015-2016 Chevy Tahoe (PPV - Police Vehicle)
Introduction
Surveillance Mode uses the Rear Backup sensors and/or Blind Spot Information System (BLIS) and
the Backup Camera. If any of the sensors detect a presence while in Surveillance Mode, the
vehicle will chime indicating which sensor tripped, and then the SMM will lock the doors and roll the
driver’s window up when Ground is momentarily applied to Pin 1 on the 4 pin connector (J6).
Surveillance Mode will still be active after a sensor is tripped to allow the backup camera to stay on.
To enter Surveillance Mode, ALL preconditions must be met:
• Transmission must be in park.
• Vehicle speed must be zero.
• Driver door must be closed.
• Service Brake must not be applied.
• Momentarily ground the Green/White wire Pin 3 on the 4 pin connector.
To exit Surveillance Mode, any condition may be applied:
• Pin 3 of the 4 pin connector Green/White wire momentarily grounded.
•
Driver door is opened.
•
Service brake is pressed.
Diagnostics
Diagnostic mode is entered by pressing the test button on the module. The module provides
diagnostic LED’s which illuminate according to the following table. There are multiple pages of
diagnostics and the page can be determined by the Status LED. Pressing the test button will cycle
through the different pages.
STATUS LED
1-1
2-2
3-3
4-4
5-5
LED 1
TR=PARK
Internal use
Internal use
SMM Ready
Internal use
LED 2
Service Brake
VSS<2
Internal use
SMM Enabled
Internal use
LED 3
Driver Door
Reverse Sensors
Internal use
SMM Tripped
Internal use
LED 4
Passenger Door
n/a
Internal use
SMM REV only
Internal use
InterMotive Inc.
12840 Earhart Ave
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 6 of 7
www.intermotive.net
products@intermotive.net
SMM601-051217-OP
Submit product registration at www.intermotive.net
If the SMM fails any step in the System Operation Test, review the installation instructions and check all connections.
If necessary, call InterMotive Technical Support at (530) 823-1048
SMM601-051217-CAD
Page 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising