HotPoint 5000 Wireless Access Point

HotPoint 5000 Wireless Access Point
®
HotPoint 5000
Wireless
Access Point
Outdoor HotPoint 5200
Indoor HotPoint 5100
HotPoint 5000 Wireless Access Point – A modular access solution for large scale, indoor
and outdoor wireless mesh networks; full network integration while permitting independent
physical placement provides optimal accessibility for Wi-Fi clients.
Seamless Outdoor and
Indoor Operation
Outdoor HotPoint 5200 access points
have rugged NEMA 4X/IP66-rated cast
aluminum enclosures and have one
weatherproof connector for attaching to a
Firetide wireless mesh node or a
conventional Ethernet port. These units
support high gain antennas and can
receive power directly from a connected
mesh node eliminating the need for an
external power supply.
Indoor HotPoint 5100 access points provide
wireless access within buildings and moving
vehicles. Each indoor access point has a
UL2043 plenum-rated enclosure and an
RJ-45 connector for attaching to a Firetide
wireless mesh node or a conventional
Ethernet port.
Dual Radio Support
HotPoint 5000 series features two
independently operating radios. Radio 1 is
capable of operating in 802.11 b/g/n mode and
Radio 2 is capable of operating in 802.11 a/n. In
addition, Radio 2 also supports client
connectivity in the 4.9 GHz based public
safety band. The radios can operate in channel
widths of 5, 10, 20 and 40 MHz (MIMO only),
with 5 and 10 MHz channel widths only
available on the 4.9 GHz band.
Access On or Off the Mesh
HotPoint wireless access points can be
mounted to a Firetide mesh node to
provide Wi-Fi access to any indoor or
outdoor location without the need for
backhaul cabling. HotPoint access points
can also connect directly to
a conventional wired infrastructure
eliminating the need to install a mesh node in
locations where wired connectivity is
readily available.
Modularity for Flexible Placement
Unlike conventional mesh networks that
combine mesh backhaul and Wi-Fi access in
the same enclosure, Firetide mesh nodes
and access points can be physically separated
allowing system integrators to optimize RF
separately for both the mesh backhaul as well
as client access.
For example, in a multi-building mesh
network, mesh nodes should be placed in
areas that enable the best connectivity
between buildings which is typically at
higher locations. However the best
locations for the access points tend to be
lower to provide the best connectivity for
Wi-Fi clients inside
a building. Because the access points and
mesh nodes are kept in separate
enclosures, they can be independently
positioned for optimal RF connectivity.
Single-point Network Management for
Mesh and Access
Whether connected directly to a Firetide
wireless mesh network or to a wired
infrastructure, the HotPoint access points
are fully integrated and managed with the
same HotView software used to manage
Firetide mesh nodes. HotView provides
remote management from
a centralized location and users can
manage all mesh and access traffic from a
single console.
Designed for Hot Spots
Layered service levels can be enabled
through Virtual APs (VAPs) and Virtual
AP Groups. Each HotPoint AP supports
up to 16 VAPs with support for a total of
128 clients, creating different logical
networks with varying levels of security,
access, and performance. Additional Hot
Spot features include user-based rate
limiting and intracell blocking.
Specifications
Models
• HotPoint 5100 Indoor Tri-band Dual
Radio Access Point
• HotPoint 5200 Outdoor Tri-band Dual
Radio Access Point
Wireless Interface
• IEEE 802.11 b/g/n on Radio 1
• IEEE 802.11 a/n on Radio 2
3 X 3 MIMO (3 antennas and
2 streams)
• Frequency ranges (Varies per Country)
2.412 – 2.483 GHz
4.94 – 4.99 GHz
5.15 – 5.25 GHz (Indoor use only)
5.25 – 5.35 GHz
5.470 – 5.725 GHz
5.725 – 5.825 GHz
• Transmit power up to 100 mW
• Auto Transmit Power Control
• 802.11d (Auto Channel Select)
• Receive sensitivity (typical)
802.11b
1 Mbps: -95 dBm
5.5 Mbps: -92 dBm
11 Mbps: -91 dBm
802.11g
6 Mbps: -95 dBm
12 Mbps: -95 dBm
54 Mbps: -78 dBm
802.11ng
HT20 HT40
-88
-73
-71
802.11a
6 Mbps: -93 dBm
12 Mbps: -93 dBm
54 Mbps: -80 dBm
802.11na
HT20 HT40
15 Mbps (MCS0) -93
-89
150 Mbps (MCS7) -75
-73
300 Mbps (MCS15) -73
- 69
• Media Access Protocol: CSMA/CA
with ACK
• Automatic channel assignment
Networking
• Up to 16 SSIDs per HotPoint
• Up to 16 independent VLANs
• DHCP client and server, separate
DHCP range per SSID
• WDS (Wireless Distribution System)
Security, Authentication and
Encryption
• 802.11i, WPA2
• 40 bit, 104 bit WEP keys
• 802.1x, RADIUS authentication
• SSID suppression
• MAC access control
• NAT
Management and Configuration
• Integrated mesh and access
management
• Centralized management via HotView Pro
• Built-in web-based management
• Remote firmware upgrade
• Physical AP grouping
Hot Spot Services
• Virtual AP Grouping
• User-based rate limiting
• Intercell/intracell blocking
• Captive portal management
• Client-based policy management
Client Access Features
• Up to 128 concurrent users
simultaneously per HotPoint
• 802.11e (WMM) (Quality of Service)
Network Ports
• One 10/100/1000 autosense Base-T port
• IEEE 802.3, 802.3u based PoE
Management Software
• HotView Pro™ mesh management
software (Separate purchase required)
Regulatory Agency Certifications
• Safety: MET Mark; IEC/EN60950-1
• FCC Part 15, CE, Industry Canada
• RoHS / CMM / WEEE
Warranty
• Hardware: one year limited warranty
(Extended warranty available for
purchase)
• Software: 90 days limited warranty
Outdoor Model
Enclosure
• Cast aluminum NEMA 4X/IP66 enclosure
• Six Type-N antenna connectors
• One weatherproof power connector
• One weatherproof Ethernet connector
• System indicator LEDs (Power, Radio 1
and Radio 2)
• Weight: 3.75 lbs (1.7 kg)
• Dimensions: 8.6”L X 8.2”W X 2.0”H
Power
• DC Input: 15 VDC ± 10%
• Power Consumption: 30 W
(Max)
• Port 1: IEEE 802.3at compliant
PoE-PD
Environmental Specifications
• Operating temperature: from -40 ºC to
+60 ºC (-40 ºF to +140 ºF)
• Storage temperature: -40 ºC to +70 ºC
(-40 ºF to +158 ºF)
• Humidity (non-condensing): 10% to 90%
• Storage humidity (non-condensing):
10% to 90%
• Max altitude: 15,000 ft (4,572 m)
Included Accessories
• Antennas: A pair of dual-band 2.4 GHz/ 5
GHz, 3 dBi omnidirectional for staging
• Mounting bracket kit for pole and
wall mounting
• PoE Injector
Indoor Model
Enclosure
• UL2043 Plenum-rated
• Antenna connector: SMA reverse
polarity female (quantity 6)
• Power connector (2.1 mm, center
positive)
• Ethernet data connector (RJ-45)
• Reset button (recessed)
• Security slot for physical locking device
• System indicator LEDs
(power, uplink, status, access)
• Weight: 14 oz (0.4 kg)
• Dimensions: 7.3”L X 6.8”W X 1.4”H
Power
• Input voltage: 48 VDC/0.83 A via
external power supply or via 802.3af
PoE PSE
• External power supply: 100–240 VAC,
50/60 Hz
• Power consumption: 16 W (Max)
Environmental Specifications
• Operating temperature: 0 ºC to +50 ºC (32
ºF to +122 ºF)
• Storage temperature: -20 ºC to +70 ºC (-4
ºF to +158 ºF)
• Humidity (non-condensing): 10% to 90%
• Storage humidity (non-condensing):
10% to 90%
• Max altitude: 15,000 ft (4572 m)
Included Accessories
• DC power adapter with North American
AC power cable
• Antennas: Three pairs, 2.4 GHz, 5 GHz, 3
dBi, omnidirectional for staging
• DC power brick
Optional Accessories
• PoE Power Injector
• Antennas
(See Antenna & Accessory Guide for options)
Firetide Products
Mesh Nodes
HotPort Indoor,
Outdoor and Edge
Mesh Nodes
Access Points
HotPoint Indoor &
Outdoor Access
Points
Mobility
Firetide Mobility
Controller
Software HotView
Pro Mesh
Management
Software
• Connectors: SMA, reverse polarity
Optional Accessories
• Antennas: External 2.4 GHz, 8 dBi
Omnidirectional 3x3 MIMO antenna
(AO-024-MIMO-8)
• Cable Assemblies: 1.5 m or 5 m length
LMR400 cable with low loss lightning
suppressor
Accessories
Antennas,
Mounting Kits,
Cables, etc.
Data Sheet
2105 South Bascom Avenue, Suite 220, Campbell, CA 95008 Tel: +1
(408) 399-7771 | sales@firetide.com | www.firetide.com
© 2014 Firetide, Inc. Firetide, HotPort and HotPoint are registered trademarks of Firetide, Inc. AutoMesh and HotView Pro are trademarks of Firetide, Inc. All other company and product are the trademarks of
their respective owners.
DSAP5000-103014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising