View 2011 Insight USB Adapter - Honda Parts at Honda Parts Now

View 2011 Insight USB Adapter - Honda Parts at Honda Parts Now
INSTALLATION
INSTRUCTIONS
Accessory
Application
USB ADAPTER
2011–2012 INSIGHT
Publications No.
AII 12058
Issue Date
OCT 2011
PARTS LIST
USB Adapter Attachment Kit
P/N 08B28-TM8-100A
Control unit bracket
USB cable
USB cable A
6 mm Flange nut
Wire tie with clip
10 Wire ties
5
Urethane tapes
USB Adapter Kit
P/N 08A28-0K1-100
Bus cable
Grommet
3
Flange bolts, 5 x 7 mm
Control unit
Bus Cable 2-Port
P/N 08A31-0F1-000
Bus cable 2-port
6 x 12 mm Washer-bolt
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 47116 (1110)
08B28-TM8-1000-91
1 of 10
TOOLS AND SUPPLIES REQUIRED
INSTALLATION
Phillips screwdriver
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
Flat-tip screwdriver
Ratchet
10 mm Combination wrench
Shop towel
Scale
File
Isopropyl alcohol
Utility knife
1.
Make sure you have the anti-theft code for the audio
unit.
2.
Disconnect the negative cable from the 12 volt
battery.
3.
Remove the passenger’s dashboard undercover
(three clips and two pins).
Pushpin
Drill
16 mm Hole saw
Eye protection (face shield, safety goggles, etc.)
8 mm and 10 mm Socket
Diagonal cutters
Plastic trim tool
T/N SILTRIMTL 10
3 mm Drill bit
Tape
3 CLIPS
Hammer (Wooden handle)
Illustration of the USB Adapter Installed in the Vehicle
BUS
CABLE
USB CABLE A
2 PINS
PASSENGER’S
DASHBOARD
UNDERCOVER
861205AE
USB CABLE
880710BE
UNIT
2 of 10
AII 47116 (1110)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
4.
Remove the glove box (one damper rod, two bolts,
and two stops).
6.
STOP
Push.
STOP
Push.
Remove the audio unit assembly:
•
Reach under the dashboard, and remove the
audio unit bolt.
•
Using the sturdy wooden handle of a hammer,
push the back of the audio unit forward to
release the eight clips.
•
Release the harness clip, and unplug the vehicle
connectors. Carefully remove the audio unit
without scratching the dashboard.
AUDIO UNIT
ASSEMBLY
GLOVE BOX
HAMMER
(WOODEN
HANDLE)
DAMPER
ROD
BOLTS
5.
AUDIO
UNIT
861206AE
Remove the center lower trim (six clips, three
retaining tabs, and unplug the vehicle connector).
AUDIO UNIT
ASSEMBLY
HARNESS
CLIP
GLOVE
BOX
OPENING
VEHICLE
CONNECTOR
6 CLIPS
AUDIO UNIT
8 CLIPS
3 RETAINING
TABS
CENTER LOWER
TRIM
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
BOLT
VEHICLE
CONNECTORS
8D0901AD
8D0902AD
AII 47116 (1110)
3 of 10
7.
Insert the key into the shift lock release slot, push
down on the key, and move the shift lever to the “D”
position. Pull the parking brake lever all the way up.
9.
RUBBER
MAT
RELEASE
BUTTON
COVER
Remove the rubber mat from the center console.
SHIFT LOCK
RELEASE SLOT
CENTER
CONSOLE
803008AY
10. Remove the parking brake lever trim (two retaining
tabs and one hook).
“D” POSITION
PARKING BRAKE
LEVER TRIM
SHIFT
LEVER
2 RETAINING
TABS
HOOK
PARKING BRAKE LEVER
Pull up.
8.
Remove the beverage holder.
BEVERAGE
HOLDER
FRONT
803003AY
CENTER
CONSOLE
803007AY
4 of 10
AII 47116 (1110)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
11. Attach masking tape to the bottom edge of the
instrument panel, around the shift lever, and around
the parking brake lever.
CENTER
CONSOLE
14. Position the control unit bracket under the floor
carpet as shown.
FRONT
2 CLIPS
CONTROL UNIT
BRACKET
2 SCREWS
INSTRUMENT
PANEL
VEHICLE
BOLT
VEHICLE
WIRE TIE
WITH CLIP
MASKING
TAPE
VEHICLE
PANEL
SHIFT
LEVER
MASKING
TAPE
PARKING
BRAKE LEVER
FRONT
FLOOR
CARPET
8N1813AY
6 mm
FLANGE
NUT
12. Carefully remove the center console (two clips and
two screws).
VEHICLE
WIRE TIE
WITH CLIP
Cut.
13. Remove the rear bolt from the vehicle frame, and
release the harness clip.
SHIFT
LEVER
6 x 12 mm
WASHER-BOLT
15. Secure the control unit bracket to the vehicle frame
with the vehicle bolt you removed in step 13, and
with one 6 x 12 mm washer-bolt with 6 mm flange nut
as shown.
VEHICLE
HARNESS
16. Using diagonal cutters, cut and remove the original
vehicle wire tie with clip.
VEHICLE BOLT
Reuse.
17. Secure the vehicle harness to the bracket with one
new wire tie with clip.
FRONT
CONTROL
UNIT
BRACKET
VEHICLE
HARNESS
FRONT
VEHICLE
FRAME
HARNESS
CLIP
871506BD
WIRE TIE
WITH CLIP
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 47116 (1110)
WIRE TIE
WITH CLIP
VEHICLE
HARNESS
BRACKET
5 of 10
18. Install the control unit to the control unit bracket with
three 5 x 7 mm flange bolts. Use a combination
wrench to tighten the flange bolts.
20. Route the bus cable and the USB cable forward
along the vehicle harness.
USB CABLE
3 FLANGE BOLTS,
5 x 7 mm
CONTROL
UNIT
FRONT
CONTROL
UNIT
VEHICLE
HARNESS
BUS
CABLE
FRONT
CONTROL UNIT
BRACKET
871603AD
19. Plug the bus cable 14-pin connector and the USB
cable 4-pin connector (corrugated tube end) into the
control unit as shown.
WIRE
TIE
21. Secure the bus cable and the USB cable to the
vehicle harness with three wire ties.
NOTE: Do not attach the wire ties to the yellow-taped
portion of the vehicle harness.
22. Continue routing the bus cable and the USB cable
forward as shown.
FRONT
FRONT
CONTROL
UNIT
USB CABLE
AIR
DUCT
BUS
CABLE
USB CABLE
4-PIN
CONNECTOR
(CORRUGATED
TUBE END)
BUS CABLE 14-PIN
CONNECTOR
URETHANE
TAPE
871604BD
VEHICLE
PANEL
871606AD
23. Remove the air duct. Using isopropyl alcohol on a
shop towel, clean the areas on the floor and the back
of the air duct where the urethane tape will attach.
24. Secure the bus cable and the USB cable to the
vehicle panel and air duct with two pieces of
urethane tape, then reinstall the air duct.
6 of 10
AII 47116 (1110)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
25. At the center lower trim opening, route the bus cable
toward the center panel opening, and route the USB
cable toward the glove box opening.
27. Bundle the excess bus cable, and secure it to the
vehicle frame with two wire ties.
BUS CABLE
Bundle the excess.
BUS CABLE
WIRE TIES
USB
CABLE
CENTER LOWER
TRIM OPENING
CENTER LOWER
TRIM OPENING
871610DD
871607CD
28. Route the USB cable into the glove box opening.
26. Align the bus cable 14-pin connector with the vehicle
24-pin connector, and secure the bus cable to the
vehicle harness with one wire tie.
VEHICLE
HARNESS
VEHICLE
FRAME
GLOVE BOX
OPENING
WIRE TIE
CENTER PANEL
OPENING
BUS
CABLE
USB CABLE
Align.
VEHICLE 24-PIN
CONNECTOR
BUS CABLE 14-PIN
CONNECTOR
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
871608CD
AII 47116 (1110)
7 of 10
29. Secure the USB cable to the vehicle frame with one
wire tie.
31. Get the glove box. Using a utility knife, cut out the
insulator on the glove box at the measurement
shown.
USB CABLE
30 mm
VEHICLE
FRAME
45 mm
WIRE TIE
GLOVE BOX
OPENING
INSULATOR
Cut.
30. Secure the USB cable to the vehicle harness with
one wire tie.
USB CABLE
GLOVE
BOX
893002AD
32. Using a pushpin, pierce the glove box in two places
at the measurements shown.
2 MARKS
RIB
30 mm
70 mm
PUSHPIN
15 mm
GLOVE BOX
OPENING
WIRE TIE
VEHICLE
HARNESS
GLOVE BOX
8N2512AE
8 of 10
AII 47116 (1110)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
33. While wearing eye protection, drill the two pierced
marks in the glove box. First drill with a 3 mm drill bit,
and finish with a 16 mm hole saw. Use a utility knife
to cut between the two 16 mm holes. Remove any
burrs.
35. Reinstall the glove box. Loosely install the two bolts.
UTILITY KNIFE
3 mm
DRILL BIT
DRILL
Cut off.
GLOVE BOX
2 BOLTS
Loosely
install.
16 mm
HOLE SAW
871616AD
36. Plug the 4-pin connector on USB cable A into the
USB cable 4-pin connector as shown.
2 MARKS
GLOVE BOX
8N2513AE
USB CABLE
4-PIN CONNECTOR
URETHANE
TAPE
34. Route the 4-pin connector end of USB cable A
through the grommet and the hole in the glove box.
Seat the grommet into the hole in the glove box.
USB CABLE A
4-PIN
CONNECTOR
USB
CABLE
USB CABLE A
4-PIN CONNECTOR
GLOVE BOX
USB
CABLE A
4-PIN
CONNECTORS
USB
CABLE A
GLOVE BOX
803006BY
37. Wrap one urethane tape around the 4-pin
connectors.
HOLE
GROMMET
871614BD
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 47116 (1110)
9 of 10
38. Secure USB cable A and the 4-pin connectors to the
vehicle harness with two wire ties.
VEHICLE
HARNESS
41. Plug the bus cable 14-pin connector or bus cable
2-port 14-pin connector into the audio unit, and
reinstall the audio unit.
4-PIN
CONNECTORS
AUDIO UNIT
BUS CABLE 14-PIN
CONNECTOR OR
BUS CABLE
2-PORT 14-PIN
CONNECTOR
WIRE
TIES
USB
CABLE A
GLOVE BOX
39. Reinstall the glove box.
If the vehicle is equipped with another accessory that
plugs into the 14-pin connector in the audio unit, continue
with step 40, otherwise go to step 41.
40. Plug the bus cable 14-pin connector and the other
accessory 14-pin connector into the bus cable 2-port
14-pin connectors. Wrap one piece of urethane tape
around each 14-pin connector.
BUS CABLE
14-PIN CONNECTOR
AUDIO UNIT
14-PIN CONNECTOR
871615CD
URETHANE
TAPE
Wrap.
871617AD
42. Check that all wire harnesses are routed properly
and all connectors are plugged in.
43. Connect the negative cable to the battery.
44. Enter the anti-theft code for the audio unit, and reset
the clock.
45. Reinstall all removed parts.
46. Turn the radio unit ON. Set the mode to USB by
pressing AUX until “USB” is shown on the radio
display. If “USB NO DATA” is on the display, the unit
is working properly.
CENTER
PANEL
OPENING
BUS CABLE
2-PORT
BUS CABLE
2-PORT 14-PIN
CONNECTORS
10 of 10
VEHICLE 14-PIN
911501AB
CONNECTOR or OTHER
ACCESSORY 14-PIN
CONNECTOR
AII 47116 (1110)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising