Belco Resources Equipment SSP-250 SSP-400 Poly Spreader

Belco Resources Equipment SSP-250 SSP-400 Poly Spreader
Operator’s Manual
Poly Fertilizer Spreaders
SSP-250 - SSP-400
Publication: February 2011
2
TABLE OF CONTENTS
INTRODUCTION .........................................................................................................................................................4
SAFETY........................................................................................................................................................................4
SAFETY SIGNAL WORDS .........................................................................................................................................5
GENERAL SAFETY GUIDELINES............................................................................................................................5
SAFETY DECAL CARE ..............................................................................................................................................6
BEFORE OPERATION ................................................................................................................................................6
DURING OPERATION ................................................................................................................................................7
HIGHWAY AND TRANSPORT OPERATIONS ........................................................................................................8
ASSEMBLY..................................................................................................................................................................9
OPERATION ..............................................................................................................................................................11
ATTACHING TO THE TRACTOR ...........................................................................................................................11
SHORTENING A PTO DRIVELINE .........................................................................................................................11
MAINTENANCE........................................................................................................................................................12
SPREADING CHART ................................................................................................................................................13
PARTS BREAKDOWN..............................................................................................................................................15
LIMITED WARRANTY.............................................................................................................................................17
WARRANTY REGISTRATION FORM & INSPECTION REPORT .......................................................................19
3
INTRODUCTION
Thank you for purchasing your Belco Resources Equipment fertilizer spreader. Your fertilizer spreader is design
to be used on Cat. 1 tractors and at 540. It is important to properly maintain in keep in place all safety guards
and shields that came with your spreader.
SAFETY
Read and understand this manual and all safety signs before operating and maintaining. Review the safety instructions and precautions annually.
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED
TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND
THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN
INJURY OR DEATH.
THIS SYMBOL MEANS
ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
4
SAFETY SIGNAL WORDS
Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages.
The appropriate signal word for each has been selected using the following guidelines:
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or
serious injury. This signal word is to be limited to the most extreme situations typically for machine
components which, for functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or
serious injury, and includes hazards that are exposed when guards are removed. It may also be used
to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
GENERAL SAFETY GUIDELINES
Safety of the operator is one of the main concerns in designing and developing a new piece of equipment.
Designers and manufacturers build in as many safety features as possible. However, every year many accidents
occur which could have been avoided by a few seconds of thought and a more careful approach to handling
equipment. You, the operator, can avoid many accidents by observing the following precautions in this section.
To avoid personal injury, study the following precautions and insist those working with you, or for you, follow
them.
Replace any CAUTION, WARNING, DANGER or instruction safety decal that is not readable or is missing.
Location of such decals is indicated in this booklet.
Do not attempt to operate this equipment under the influence of drugs or alcohol.
Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a
responsible adult familiar with farm machinery and trained in this equipment’s operations. Do not allow
persons to operate or assemble this unit until they have read this manual and have developed a thorough
understanding of the safety precautions and of how it works.
To prevent injury or death, use a tractor equipped with a Roll Over Protective System (ROPS). Do not paint
over, remove or deface any safety signs or warning decals on your equipment. Observe all safety signs and
practice the instructions on them.
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is in question DON’T TRY IT.
5
SAFETY DECAL CARE
•
Keep safety signs clean and legible at all times.
•
Replace safety signs that are missing or have become illegible.
•
Replaced parts that displayed a safety sign should also display the current sign.
•
Safety signs are available from your Distributor or Dealer Parts Department or the factory.
How to Install Safety Signs:
•
Be sure that the installation area is clean and dry.
•
Decide on the exact position before you remove the backing paper.
•
Remove the smallest portion of the split backing paper.
•
Align the decal over the specified area and carefully press the small portion with the exposed sticky backing
in place.
•
Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place.
•
Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing paper.
BEFORE OPERATION
•
Carefully study and understand this manual.
•
Do not wear loose-fitting clothing, which may catch in moving parts.
•
Always wear protective clothing and substantial shoes.
•
Assure that all tires are inflated evenly.
•
Give the unit a visual inspection for any loose bolts, worn parts or cracked welds, and make necessary repairs.
Follow the maintenance safety instructions included in this manual.
•
Be sure that there are no tools lying on or in the equipment.
•
Do not use the unit until you are sure that the area is clear, especially children and animals.
•
Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar with your new
equipment.
•
Practice operation of your equipment and its attachments. Completely familiarize yourself and other operators with its operation before using.
•
Use a tractor equipped with a Roll Over Protective System (ROPS) and fasten your seat belt prior to starting
the engine.
6
•
The manufacturer does not recommend usage of tractor with ROPS removed.
•
Move tractor wheels to the widest recommended settings to increase stability.
•
Securely attach to towing unit. Use a high strength, appropriately sized hitch pin with a mechanical retainer
and attach safety chain.
•
Do not allow anyone to stand between the tongue or hitch and the towing vehicle when backing up to the
equipment.
DURING OPERATION
•
Children should not be allowed on the product.
•
Clear the area of small children and bystanders before moving the feeder.
•
If using a towing unit, securely attach feeder by using a hardened 3/4” pin, a metal retainer, and safety
chains if required. Shift towing unit to a lower gear before going down steep downgrades, thus using the
engine as a retarding force. Keep towing vehicle in gear at all times. Slow down for corners and rough terrain.
Make sure you are in compliance with all local and state regulations regarding transporting equipment on
public roads and highways. Lights and slow moving signs must be clean and visible by overtaking or oncoming traffic when feeder is transported.
•
•
Beware of bystanders, particularly children! Always look around to make sure that it is safe to start the
engine of the towing vehicle or move the unit. This is particularly important with higher noise levels and
quiet cabs, as you may not hear people shouting.
•
NO PASSENGERS ALLOWED - Do not carry passengers anywhere on, or in, the tractor or equipment,
except as required for operation.
•
Keep hands and clothing clear of moving parts.
•
Do not clean, lubricate or adjust your equipment while it is moving.
•
When halting operation, even periodically, set the tractor or towing vehicle brakes, disengage the PTO, shut
off the engine and remove the ignition key.
•
Be especially observant of the operating area and terrain - watch for holes, rocks or other hidden hazards.
Always inspect the area prior to operation.
•
DO NOT operate near the edge of drop-offs or banks.
•
DO NOT operate on steep slopes as overturn may result.
•
Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.
7
HIGHWAY AND TRANSPORT OPERATIONS
•
Adopt safe driving practices:
⇒ Keep the brake pedals latched together at all times. NEVER USE INDEPENDENT BRAKING WITH
MACHINE IN TOW AS LOSS OF CONTROL AND/OR UPSET OF UNIT CAN RESULT.
⇒ Always drive at a safe speed relative to local conditions and ensure that your speed is low enough for an emergency stop to be safe and secure. Keep speed to a minimum.
⇒ Reduce speed prior to turns to avoid the risk of overturning.
⇒ Avoid sudden uphill turns on steep slopes.
⇒ Always keep the tractor or towing vehicle in gear to provide engine braking when going downhill. Do not coast.
⇒ Do not drink and drive!
•
Comply with state and local laws governing highway safety and movement of farm machinery on public roads.
•
Use approved accessory lighting flags and necessary warning devices to protect operators of other vehicles on
the highway during daylight and nighttime transport. Various safety lights and devices are available from your
dealer.
•
The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use.
Local laws should be checked for all highway lighting and marking requirements.
•
When driving the tractor and equipment on the road or highway under 40 kph (20 mph) at night or during the
day, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem.
•
Plan your route to avoid heavy traffic.
•
Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersections, etc.
•
Be observant of bridge loading ratings. Do not cross bridges rated lower than the gross weight as which you are
operating.
•
Watch for obstructions overhead and to the side while transporting.
•
Always operate equipment in a position to provide maximum visibility at all times. Make allowances for increased length and weight of the equipment when making turns, stopping the unit, etc.
•
Pick the levelest possible route when transporting across fields. Avoid the edges of ditches or gullies and steep
hillsides.
•
Be extra careful when working on inclines.
•
Maneuver the tractor or towing vehicle at safe speeds.
•
Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or death.
•
Avoid loose fill, rocks and holes; they can be dangerous for equipment operation or movement.
•
Allow for unit length when making turns.
•
Operate the towing vehicle from the operator’s seat only.
•
Never stand alongside of unit with engine running or attempt to start engine and/or operate machine while standing alongside of unit.
•
Never leave running equipment attachments unattended.
•
As a precaution, always recheck the hardware on equipment following every 100 hours of operation. Correct all
problems. Follow the maintenance safety procedures.
8
Assembly
Hopper
1. Secure the spreader hopper support pan to the bottom of the hopper with the 4 carriage head
bolts and nuts.
2. With the hopper opening facing up, insert the Retainer Bushing through the center hole of the hopper. The bushing rim should be on the inside of the hopper against the metal bowl.
3. Turn the hopper upside down.
4. Slip the 2-hole (Top Shutter Plate Flow Control) Galvanized disc over the bushing and against the
hopper bottom.
5. Do the same with the 3-hole (Bottom shutter Plate Directional Control) Galvanized disc. Important: See photo to be sure the discs are flipped the proper way.
6. Put the 4 3/8” washer over the Retainer bushing.
Secure everything in place with the snap ring.
IMPORTANT: Make sure both holes can be exposed after the discs are assembled. If not assembled correctly, the openings will not line up when the gates are supposed to be open.
9
Frame
1. Install the spin disc on the gearbox output shaft. Secure it in
place with the 8mm roll pin in the lower most hole, which is closest to the gearbox housing.
2. Install the deflector shield on the inside of the frame. Bolt it to
the tabs welded in front of the lower hitch pins on the frame. Secure it in place with the 10 x 25mm bolts, flat washers, and Hex
nuts.
3. Secure the Fixed Pivot to the deflector shield with an 8mm nut
and flat washer.
4. Loosely attach the left and right hopper support arms to the frame
using the M10 x 25mm bolts, lock washers and Hex nuts. The
notch end goes on the frame. Do not tighten.
5. Attaching the adjustment spreader lever. Slip the adjustment lever through the scaled slot. Put the spring over the 10 x
70mm bolt. Insert the bolt through the spreader lever and put
the fiber spacer next to the lever. Put the bolt through the frame
and secure in place with the 10mm lock nut. Compress the
spring by tightening the bolt and nut until there is resistance in
moving the handle up and down.
6. Installing the Threaded Adjustment Block. Slip the wing
bolt through the indication gauge and then through the scaled
slot on the frame. Thread the wing bolt through the solid block
to secure it to the frame.
7. Flip the hopper right side up, and position it over the frame.
Slide center hole over the gearbox output shaft. Secure the
back of the hopper in place by slipping the large washer over a
10 x 35mm bolt and sliding it through hopper and then through
the frame near the top hitch. Secure it in place with a 10mm
flat washer, lock washer and hex nut. Insert the support bar and
bolt it in place with the 10 x 25mm bolts. The flat washers,
lock washers and hex nuts are tightened against the hopper supports.
8. Install the nylon dust washer over the gearbox output shaft and
slide it down until lit rests against the bottom of the hopper.
Install the agitator with the 8 x 50mm bolt and lock nut.
9. Attach the Tie Rod to the Top Shutter Plate and secure it with R
clips and 2 - 10mm flat washers.
10. Install the Directional lever to the Bottom Shutter Plate and
secure the end to directional disc with 2mm cotter pin and 8mm
flat washer and the R clip to the Fixed Pivot bolted to the deflector shield.
Tighten all hardware.
10
Operation
Attaching to the tractor
1. With the Fertilizer Spreader on a level surface, back the Cat. 1 tractor so the tractor lift arms are even with the
2.
3.
4.
5.
6.
7.
fertilizer spreader lower hitch pins. Lower or raise the tractor hitch arms until the 7/8” bushing in the arm is
level with the hitch pins. Be sure nothing is between the tractor and the cutter before backing up.
Insert the lower link hitch hole of the tractor’s lift arm over the implement’s hitch pin.
Secure the lift arm in place by using a 7/16” lynch pin or other fastener.
Repeat with the other arm.
Connect the driveline to the tractor’s PTO output shaft. Secure it in place with the bolt supplied with the
driveline.
Connect the tractor top link to the upper pivot hitch of the fertilizer spreader.
Start the tractor and slowly raise the fertilizer spreader. Check for drawbar interference. Be sure that the PTO
driveline does not bottom out when lifting the fertilizer spreader to it’s maximum height. If it does appear that
it could bottom out, it is necessary to shorten the PTO driveline. (See Shortening a PTO Driveline section).
Ensure that in the working position there is an overlap of a minimum of 1/3 the length of each profile.
Shortening a PTO Driveline
1. With the implement attached to the tractor’s three point hitch, and the PTO driveline not installed, separate
2.
3.
4.
5.
the PTO driveline. Attach the implement end to the implement and the other end to the tractor PTO input
shaft.
Raise the implement by using the tractor’s hydraulic 3-point hitch to it’s maximum lift height.
Hold the half shafts next to each other and mark them so each end is approximately ½” from hitting the end of
the telescopic profiles.
Shorten the inner and out guard tubes equally.
Shorten the inner and outer profiles by the same length as the guard tubes. Using a rattail file, round off all
sharp edges and burrs. Grease the telescopic profile generously before reassembling.
Do not shorten too much, the proper overlap is a minimum of 1/3 the length of each profile.
Spreading Height
Before operating the spreader, make sure that the spreading disc is set to the horizontal position and it is about 30”
from ground level.
Spreading with revolving vanes.
Since fertilizers vary with respect to weights and density, in order to obtain a perfect spreading it may be necessary
to adjust the vanes in order to compensate for these differences. The vanes are usually set to the center position.
By moving the vanes forward, distribution is increased towards the left side of the tractor operator, moving them
backwards causes distribution to be increased towards the right.
Left– Center – Right Spreader pattern
A simple adjustment of the lower lever allows directioning of the spreader pattern towards the right , center or left
of the tractor
Removal and Storage
After finishing, remove the spreader from the tractor.
1. Put the PTO driveline in a safe location so it will not become damaged.
Wash out the spreader, removing all fertilizer or other material.
11
FOLLOWING OPERATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Following operation, or when unhitching, stop the tractor or towing vehicle, set the brakes, disengage the PTO
and all power drives, shut off the engine and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock
injury could result.
Do not permit children to play on or around the stored unit.
Make sure all parked machines are on a hard, level surface and engage all safety devices.
Wheel chocks may be needed to prevent unit from rolling.
Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building.
The exhaust fumes may cause asphyxiation.
Be certain all moving parts on attachments have come to a complete stop before attempting to perform maintenance.
Always use the proper tools or equipment for the job at hand.
Use extreme caution when making adjustments.
Never replace hex bolts with less than grade five bolts unless otherwise specified.
After servicing, be sure all tools, parts and service equipment are removed.
Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement
parts must be used to restore your equipment to original specifications. The manufacturer will not claim responsibility for use of unapproved parts and/or accessories and other damages as a result of their use.
If equipment has been altered in any way from original design, the manufacturer does not accept any liability for
injury or warranty.
MAINTENANCE
Although the hopper of your spreader is fabricated with polypropylene, and therefore impervious to rust and corrosion, it is very important that the other parts of the spreader be kept clean due to the corrosive properties of fertilizers.
Item
Interval
PTO shaft grease zerks
Grease weekly
PTO shaft telescopic tubing
Grease every 40 hours
Clean spreader
After each use.
gearbox is sealed and filled with grease so not maintenance is necessary.
12
The
Spreading Charts
Fertilizer Type
Spread
Width
MPH
LBS PER ACRE
Gate setting
Granular
Fertilizer
Medium
Crystalline
Fertilizer
Calcium
Cyanamid
& Similar
Ammonium
Sulph. (CR)
Thomas Metal
39
26
32
10
20
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
1
174
285
484
815
1052
1326
1554
1870
2105
2414
2622
2919
2.5
84
121
202
336
435
545
640
762
854
987
1071
1172
5
46
60
106
176
222
277
320
392
436
494
535
596
7.5
29
40
92
121
151
191
216
260
294
336
365
400
10
17
30
52
86
113
136
166
197
231
253
279
295
1
330
546
1007
1632
2019
2587
3024
3603
4033
4476
4908
5407
2.5
115
219
412
661
816
1053
1221
1446
1621
1801
1973
2174
5
68
112
209
329
416
534
614
730
821
907
989
1092
7.5
44
76
140
223
280
364
415
490
546
606
664
728
10
30
54
100
171
208
275
318
363
408
455
496
549
1
275
750
1104
1636
2020
1844
2868
3345
4289
2.5
109
300
453
662
809
994
1158
1343
1508
5
58
149
229
297
407
495
584
672
755
7.5
37
99
148
218
272
333
388
449
502
10
26
73
112
166
204
251
289
336
376
1
142
565
924
1391
1779
2199
2607
3061
3355
3767
4039
4521
2.5
61
224
373
557
716
886
1040
1228
1347
1512
1621
1810
5
28
114
188
281
362
444
519
615
671
757
809
909
7.5
23
73
122
189
241
295
348
418
451
508
544
607
10
15
58
94
143
180
222
262
308
336
378
410
453
1
2262
5037
6670
6929
4
572
1277
1685
1736
7
290
537
843
869
12
195
427
297
583
13
Belco Resources Equipment
SSP-250 - SSP-400
Frame - Parts Breakdown
14
Belco Resources Equipment
SSP-250 - SSP-400
Frame - Parts Breakdown
Part No.
Part #
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
5SB16153
5SB3016
5SB07015
5SB12048
5SB19287
5SB19286
5SB19306
5SB06099
5SB19312
5SB11005
5SB07001
5SB19299
5SB06103
5SB19297
5SB06097
5SB11056
5SB07090
5SB06112
5SB19227
5SB07073
5SB19394
5SB04131A
5SB16152
5SB3010
5SB07075
5SB3012
5SB11045
5SB19300
5SB19301
5SB06095
5SB19291
5SB3013
5SB3014
5SB12055
5SB19292
5SB19296
5SB19307
5SB19308
5SB06094
5SB06063
5SB01429
5SB06096
5SB3000
5SB07079A
5SB21036
5SB11019
5SB3015
5SB10129
5SB19294
Description
Base Assembly
Bolt, Hex Head M10x20,Zinc
Flat Washer Zinc Plated 10mm
R Clips
Tie Rod
Lever
Spreader Spring
Bolt, Hex Head M10x70,Zinc
Hopper Support Arm (Right Side)
Hex Head Nut 10 x 1.5
Split Type 10mm Lockwasher
Directional Lever
Shutter Adjustment Pivot Joint
Agitator
Hex Head Bolt 8 x 2.5 x 45
8mm Nylon Locking Nut
25 x 60 x 3.o Nylon Washer
Bolt, Carridge, M10x25, Zinc
Bar - Hopper reinforcement
Hopper Support Washer
Hopper
Retainer Bushing
Hopper Support Pan
Bolt Carridge,M8x25, Zinc
8mm Flat Washer Zinc Plated
Washer,Lock,8mm, Zinc
Hex Head Nut 8 x 1.25
Top Shutter Plate (Flow Control)
Bottom Shutter Plate (Directional)
Hex Head Bolt 8 x 1.25 x 16
Distributor Vane
Roll Pin,ø8*40,
Roll Pin,ø6*40,
Lever, Fixed Pivot
Spreader Disc
Front Shield
Threaded Adj. Block
Gauge Pointer
Thumb Screw
Bolt Hex Head M10x25, Zinc
Gearbox
Hex Bolt 10 x 1.5 x 110
PTO Assembly (complete)
Flat Washer - Hardened
Snap Ring
M10 Lock Nut
Washer,Lock
Adjustment Lever Washer, Bakelite
Hopper Support Arm (Left Side)
15
Qty
1
2
5
4
1
1
1
1
1
14
10
1
1
1
1
1
1
5
1
1
1
1
1
6
14
14
15
1
1
8
4
1
1
1
1
1
1
1
1
4
1
3
1
1
1
1
4
1
1
Belco Resources Equipment
SSP-250 - SSP-400
PTO Shaft - Parts Breakdown
Position
Part #
Description
1
2
3
4
5SB3001
5SB3002
5SB3003
5SB3004
Yoke
Inner Yoke complete
Outer Yoke complete
Inner PTO Guard Complete
2
1
1
1
5
5SB3005
Outer PTO Guard Complete
1
6
7
5SB3006
5SB3007
5SB3000
Cross & Bearing
Safety Chain
PTO Shaft Complete
2
2
16
Qty
LIMITED WARRANTY
Belco Resources Equipment warrants to the original purchaser of any new piece of
machinery from Belco Resources Equipment, purchased from an authorized Belco Resources Equipment dealer, that the equipment be free from defects in material and workmanship for a period of
one (1) year for non-commercial, state, and municipalities’ use, ninety (90) days for commercial use
from date of retail sale. Warranty for rental purposes is thirty (30) days. The obligation of Belco
Resources Equipment to the purchaser under this warranty is limited to the repair or replacement of
defective parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no
cost to the user at an authorized Belco Resources Equipment dealer during regular working hours.
Belco Resources Equipment reserves the right to inspect any equipment or parts which are claimed
to have been defective in material or workmanship.
This limited warranty does not apply to and excludes wear items such as shear pins,
tires, tubes knives, blades or other wear items. Oil or grease is not covered by this
warranty.
All obligations of Belco Resources Equipment under this limited warranty shall be terminated if:
Proper service is not preformed on the machine
The machine is modified or altered in any way.
The machine is being used or has been used for purposes other than those
for which the machine was intended.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Belco Resources Equipment obligation under this limited warranty, to the extent
allowed by law, is in lieu of all warranties, implied or expressed, including implied warranties of merchantability and fitness for a particular purpose and any
liability for incidental and consequential damages with respect to the sale or use
of the items warranted. Such incidental and consequential damages shall include
but not be limited to: transportation charges other than normal freight charges;
cost of installation other than cost approved by Belco Resources Equipment; duty;
taxes; charges for normal service or adjustment; loss of crops or any other loss of
income; rental of substitute equipment, expenses due to loss, damage, detention or
delay in the delivery.
17
18
WARRANTY REGISTRATION FORM & INSPECTION REPORT
This form must be filled out by the dealer and signed by both dealer and customer at time of delivery.
Customer name ____________________________
Dealer name _______________________________
Address __________________________________
Address ___________________________________
City, state, code ____________________________
City, state, code ____________________________
Phone number ______________________________
Dealer Account # ____________________________
Tractor Make ______________________________
Model ____________________________________
Model ______________ HP __________________
Serial Number ______________________________
Type of Application (Commercial Maintenance,
Private Homeowner, Landscaping, Farm, etc)
__________________________________________
Delivery Date ______________________________
DEALER INSPECTION REPORT
CUSTOMER WARRANTY UNDERSTANDING
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
I hereby acknowledge that:
I have received and accepted delivery of the machine described. The equipment was thoroughly inspected for loose
and/or missing parts and has been adjusted in accordance
with the Pre-Delivery Checklist.
I have read and understand the nature and extent of the
warranty and understand clearly that there were and are no
other representations of warranties, either expressed or
implied, made by any person. I have been advised on
proper operation, maintenance and lubrication prodecure
of this equipment.
I have been instructed on and do understand the application, limitation and capacities this equipment was designed
and recommended for, all as described in the Operator’s
Manual and Product Literature provided by Belco Resources Equipment.
Tightened All Hardware
Safety Guards In Place
Safety Decals In Place
Fittings Greased
Oil In Gearbox
Bolts Correctly Torqued
Unit Attached to Tractor
Field Adjusted
Operator’s Manual Is Present
Review operating and safety instructions
I have thoroughly instructed the buyer on the above-described equipment; review included the operator’s
manual content, equipment care, adjustments, safe operation and applicable warranty policy.
Date _______________________
Dealer’s signature _______________________________________
The above equipment and operator’s manual have been received by me, and I have been thoroughly instructed as to care, adjustments, safe operation and applicable warranty policy.
Date _______________________
Customer’s signature ____________________________________
Mail to: Belco Resources Equipment Division
P.O. Box 8164
Rocky Mount, NC 27804
19
Increasing agricultural productivity since 1974
Belco Resources Equipment
P.O. Box 8164
Rocky Mount, NC 27804
www.BR-Equipment.com
20
Tel: 252-442-0700
Fax: 252-442-0787
Sales@BRGlimited
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising