Spivi® For Keiser M3i bikes Installation Manual

Spivi® For Keiser M3i bikes Installation Manual
Spivi® For Keiser M3i bikes
Installation Manual
TABLE OF CONTENTS
Contents
CHAPTER 1: BEFORE WE BEGIN ...................................................................................... 2
CHAPTER 2: UNPACKING THE SPIVI SYSTEM ..................................................................... 3
CHAPTER 3: SYSTEM ASSEMBLY...................................................................................... 4
CHAPTER 4: TURNNING THE SYSTEM ON ......................................................................... 5
CHAPTER 5: RADIO FREQUENCY (RF) INTERFERENCE ......................................................... 5
CHAPTER 6: IMPORTANT PRECAUTIONS .......................................................................... 6
CHAPTER 7: WARRANTY ................................................................................................ 6
CHAPTER 8: COPYRIGHT ................................................................................................ 7
CHAPTER 1: BEFORE WE BEGIN
Congratulations on choosing the Spivi!
Read this guide to learn how to:
-Assemble the system in your studio
-Make it ready for our remote configuration process
Visit www.spivi.com/academy to learn more about your new system.
2
CHAPTER 2: UNPACKING THE SPIVI SYSTEM
Open the box to expose the system and packaging.
A
A
Remove all items from the box including foam inserts.
Ensure all the following items are included:
Name
A Spivi Rendering Server (Computer)
B XBOX Controller
C XBOX Controller Wireless Receiver
D AA Battery for XBOX Controller
E CAT5 Network Cable
F Power Cord
G BLE USB Stick
Quantity
1
1
1
1
1
1
1
C
B
A
A
D
E
A
A
Additional tools that may be helpful:
H
F
- Zip ties
I
G
AA
A
A
K
A
L
A
3
CHAPTER 3: SYSTEM ASSEMBLY
1. Unpack the Spivi Rendering Server and physically install it near your sound system and
where your display (LCD/TV/Projector) HDMI/DVI cable is ready to connect.
2. Connect the Spivi Rendering Server to a power outlet using the provided power cord.
3. Using a CAT5 network cable, connect the Spivi Rendering Server to your network.
Your infrastructure internet connection must have DHCP service enabled.
4. Connect the XBOX Controller Wireless Receiver to a USB PORT on the BACK of the Spivi
Rendering Server.
5. Insert the BLE USB Stick to the FRONT USB PORT located on the FRONT RIGHT side of
the Spivi Rendering Server.
6. Unpack the AA batteries and install them into the XBOX controller.
Back USB Ports
CAT5 Network Port
to Spivi WIFI Router
HDMI
DVI
Audio
Output
(Optional)
NOTICE: DO NOT USE THESE VIDEO OUTPUTS!
* Computer back may look different
4
CHAPTER 4: TURNNING THE SYSTEM ON
To turn the system on:
1. Turn on the Spivi Rendering Server (computer) by pressing once on the power button
(located at the front-right side)
2. Turn on the Xbox controller by pressing and holding the Silver button on the center of the
controller.
CHAPTER 5: RADIO FREQUENCY (RF) INTERFERENCE
Radio frequency (RF) interference with other devices may cause intermittent loss of
information. Wireless Internet access points, microwaves, cordless phones, or other wireless
devices may cause frequency interference. To mitigate the chance of interference, set
wireless access points to the lowest channel possible and keep the Spivi WIFI Bridge away
from interfering devices. To change the channel on the access point, please consult
manufacturer’s documentation.
Spivi utilizes ANT+ and BLE technologies to ensure a robust and reliable connection between
the various sensors used and our product. Sensors are defined as power meter sensors,
heart rate strap sensors, cadence sensors, speed sensors, and controlled resistance sensors.
Statement of Compliance for FCC and Industry Canada:
This device complies with Industry Canada and Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Changes or modifications to this device not expressly approved by the party responsible for
compliance with FCC regulations (the manufacturer) could void the user authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
5
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit difference from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CHAPTER 6: IMPORTANT PRECAUTIONS
It is the responsibility of the owner to ensure that all users of this Spivi are adequately
informed of all warnings and precautions. For questions regarding this guide, contact
Customer Service at the number listed at the end of this guide.
WARNING: Any of the provided products, parts and items are not water proof.
CHAPTER 7: WARRANTY
Manufacturer’s Warranty (under normal use)
Spivi Rendering Server: One Year
Parts, Electronics and Appearance: One Year
WARNING: WARRANY AVOIDS IF THE SPIVI COMPUTER HAS BEEN USED FOR ANYTHING ELSE
BUT RUNNING THE SPIVI SOFTWARE OR IF ANY 3rd PARTY SOFTWARE HAS BEEN INSTALLED
ON THE SPIVI COMPUTER.
In the event of a warranty issue, SpiviTech LTD will repair or replace the item at its
discretion. SpiviTech LTD is not responsible for any indirect or consequential costs or
damages associated with the warranty of the product. Our products are not covered under
warranty in cases exhibiting signs of abuse, improper maintenance or installation, crash,
using the product with non-compatible components, or using the product for purposes for
which it was not designed. This warranty is also void if the product has been modified from
its original form, including changes in aesthetics, serial numbers or logos.
Warranty Procedures: If it appears that a Spivi component is not working properly, please
take the time to inspect and troubleshoot the system as best as possible. In many instances,
solutions may be as simple as replacing a battery or reconnecting a cable. Often small parts
can repaired at a computer shop, instead of the longer and more expensive option of
sending the unit back for repair. To warranty the Spivi, return the product, where purchased
or contact SpiviTech LTD. at 1-650-318-5280
6
CHAPTER 8: COPYRIGHT
All rights reserved. No part of this publication may be copied, photographed, reproduced,
translated, transmitted electronically or placed on digital media without the prior written
consent of SpiviTech LTD.
Trademarks
Spivi is a registered trademark of SpiviTech LTD. Other product, brand, or trade names used
in this guide may be trademarks or registered trademarks of their respective owners.
Modifications
SpiviTech LTD reserves the right to make improvements and/or updates to the products
described herein at any time without notice.
Customer Service
Tel: 1-650-318-5230
Email: support@spivi.com
www.spivi.com
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising