Siemens Micromaster 430 Manual

Siemens Micromaster 430 Manual
MICROMASTER 430
7.5 kW - 250 kW
Operating Instructions
User Documentation
6SE6400-5AE00-0BP0
Issue 10/06
MICROMASTER 430 Documentation
Getting Started Guide
Is for quick commissioning with SDP and BOP-2.
Operating Instructions
Gives information about features of the
MICROMASTER 430, Installation, Commissioning,
Control modes, System Parameter structure,
Troubleshooting, Specifications and available options
of the MICROMASTER 430.
Parameter List
The Parameter List contains the description of all
Parameters structured in functional order and a
detailed description. The Parameter list also includes
a series of function plans.
Catalogues
In the catalogue you will find all the necessary
information to select an appropriate inverter, as well
as filters, chokes, operator panels and
communication options.
MICROMASTER 430
7.5 kW - 250 kW
Overview
1
Installation
2
Commissioning
3
MICROMASTER 430
4
Functions
Operating Instructions
User Documentation
System Parameters
5
Troubleshooting
6
Specifications
7
Available options
8
Electro-Magnetic
9
Compatibility
Valid for
Converter Type
MICROMASTER 430
Issue 10/06
Appendices
Software Version
V2.1
Index
Issue 10/06
A
B
C
D
E
F
G
Further information can be obtained from Internet
website:
http://www.siemens.de/micromaster
Approved Siemens Quality for Software and Training
is to DIN ISO 9001, Reg. No. 2160-01
The reproduction, transmission or use of this document,
or its contents is not permitted unless authorized in
writing. Offenders will be liable for damages. All rights
including rights created by patent grant or registration of a
utility model or design are reserved.
© Siemens AG 2002, 2005, 2006. All Rights Reserved.
MICROMASTER® is a registered trademark of Siemens
Other functions not described in this document may be
available. However, this fact shall not constitute an
obligation to supply such functions with a new control, or
when servicing.
We have checked that the contents of this document
correspond to the hardware and software described.
There may be discrepancies nevertheless, and no
guarantee can be given that they are completely identical.
The information contained in this document is reviewed
regularly and any necessary changes will be included in
the next edition. We welcome suggestions for
improvement.
Siemens handbooks are printed on chlorine-free paper
that has been produced from managed sustainable
forests. No solvents have been used in the printing or
binding process.
Document subject to change without prior notice.
Order number: 6SE6400-5AE00-0BP0
Siemens-Aktiengesellschaft
MICROMASTER 430
4
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Foreword
Foreword
User Documentation
WARNING
Before installing and commissioning the inverter, you must read all safety
instructions and warnings carefully including all the warning labels attached to the
equipment. Make sure that the warning labels are kept in a legible condition and
replace missing or damaged labels.
Information is also available from:
Regional Contacts
Please get in touch with your contact for Technical Support in your Region for
questions about services, prices and conditions of Technical Support.
Central Technical Support
The competent consulting service for technical issues with a broad range of
requirements-based services around our products and systems.
Europe / Africa
Tel:
+49 (0) 180 5050 222
Fax:
+49 (0) 180 5050 223
Email: adsupport@siemens.com
America
Tel:
+1 423 262 2522
Fax:
+1 423 262 2589
Email: simatic.hotline@sea.siemens.com
Asia / Pazific
Tel:
+86 1064 757 575
Fax:
+86 1064 747 474
Email: adsupport.asia@siemens.com
Online Service & Support
The comprehensive, generally available information system over the Internet, from
product support to service & support to the support tools in the shop.
http://www.siemens.com/automation/service&support
Contact address
Should any questions or problems arise while reading this manual, please contact
the Siemens office concerned using the form provided at the back this manual.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
5
Definitions and Warnings
Issue 10/06
Definitions and Warnings
DANGER
indicates an immiently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING
indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
used with the safety alert symbol indicates a potentially hazardous situationwhich,
if not avoided, may result in minor or moderate injury.
CAUTION
used without safety alert symbol indicates a potentially hzardous situation which, if
not avoided, may result in a property demage.
NOTICE
indicates a potential situation which, if not avoided, may result in an undesireable
result or state.
NOTE
For the purpose of this documentation, "Note" indicates important information
relating to the product or highlights part of the documentation for special attention.
Qualified personnel
For the purpose of this Instruction Manual and product labels, a "Qualified person"
is someone who is familiar with the installation, mounting, start-up and operation of
the equipment and the hazards involved.
He or she must have the following qualifications:
1. Trained and authorized to energize, de-energize, clear, ground and tag circuits
and equipment in accordance with established safety procedures.
2. Trained in the proper care and use of protective equipment in accordance with
established safety procedures.
3. Trained in rendering first aid.
PE
¾ PE – Protective Earth uses circuit protective conductors sized for short circuits
where the voltage will not rise in excess of 50 Volts. This connection is normally
= Ground
used to ground the inverter.
¾
- Is the ground connection where the reference voltage can be the same as
the Earth voltage. This connection is normally used to ground the motor.
Use for intended purpose only
The equipment may be used only for the application stated in the manual and only
in conjunction with devices and components recommended and authorized by
Siemens.
MICROMASTER 430
6
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Safety Instructions
Safety Instructions
The following Warnings, Cautions and Notes are provided for your safety and as a
means of preventing damage to the product or components in the machines
connected. This section lists Warnings, Cautions and Notes, which apply generally
when handling MICROMASTER 430 Inverters, classified as General, Transport &
Storage, Commissioning, Operation, Repair and Dismantling & Disposal.
Specific Warnings, Cautions and Notes that apply to particular activities are
listed at the beginning of the relevant chapters and are repeated or supplemented
at critical points throughout these sections.
Please read the information carefully, since it is provided for your personal
safety and will also help prolong the service life of your MICROMASTER 430
Inverter and the equipment you connect to it.
General
WARNING
¾ This equipment contains dangerous voltages and controls potentially dangerous
rotating mechanical parts. Non-compliance with Warnings or failure to follow
the instructions contained in this manual can result in loss of life, severe
personal injury or serious damage to property.
¾ Only suitable qualified personnel should work on this equipment, and only after
becoming familiar with all safety notices, installation, operation and
maintenance procedures contained in this manual. The successful and safe
operation of this equipment is dependent upon its proper handling, installation,
operation and maintenance.
¾ Risk of electric shock. The DC link capacitors remain charged for five minutes
after power has been removed. It is not permissible to open the equipment
until 5 minutes after the power has been removed.
¾ The following terminals can carry dangerous voltages even if the inverter is
inoperative:
♦ the power supply L/L1, N/L2, L3 resp. U1/L1, V1/L2, W1/L3
♦ the motor terminals U, V, W resp. U2, V2, W2
♦ and depending on the frame size the terminals DC+/B+, DC-, B-, DC/R+
resp. DCPS, DCNS, DCPA, DCNA
¾ HP ratings are based on the Siemens 1LA motors and are given for guidance
only; they do not necessarily comply with UL or NEMA HP ratings.
CAUTION
¾ Children and the general public must be prevented from accessing or
approaching the equipment!
¾ This equipment may only be used for the purpose specified by the
manufacturer. Unauthorized modifications and the use of spare parts and
accessories that are not sold or recommended by the manufacturer of the
equipment can cause fires, electric shocks and injuries.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
7
Safety Instructions
Issue 10/06
NOTICE
¾ Keep these operating instructions within easy reach of the equipment and make
them available to all users
¾ Whenever measuring or testing has to be performed on live equipment, the
regulations of Safety Code VBG 4.0 must be observed, in particular §8
“Permissible Deviations when Working on Live Parts”. Suitable electronic tools
should be used.
¾ Before installing and commissioning, please read these safety instructions and
warnings carefully and all the warning labels attached to the equipment. Make
sure that the warning labels are kept in a legible condition and replace missing
or damaged labels.
Transport & Storage
WARNING
¾ Correct transport, storage, erection and mounting, as well as careful operation
and maintenance are essential for proper and safe operation of the equipment.
CAUTION
¾ Protect the inverter against physical shocks and vibration during transport and
storage. Also be sure to protect it against water (rainfall) and excessive
temperatures (see table on page 80).
Commissioning
WARNING
¾ Work on the device/system by unqualified personnel or failure to comply with
warnings can result in severe personal injury or serious damage to material.
Only suitably qualified personnel trained in the setup, installation,
commissioning and operation of the product should carry out work on the
device/system.
¾ Only permanently-wired input power connections are allowed. This equipment
must be grounded (IEC 536 Class 1, NEC and other applicable standards).
¾ If a Residual Current-operated protective Device (RCD) is to be used, it must be
an RCD type B. Machines with a three-phase power supply, fitted with EMC
filters, must not be connected to a supply via an ELCB (Earth Leakage CircuitBreaker - see DIN VDE 0160, section 5.5.2 and EN 50178 section 5.2.11.1).
¾ The following terminals can carry dangerous voltages even if the inverter is
inoperative:
- the power supply L/L1, N/L2, L3 resp. U1/L1, V1/L2, W1/L3
- the motor terminals U, V, W resp. U2, V2, W2
- and dependeing on the frame size the terminals DC+/B+, DC-, B-, DC/R+
resp. DCPS, DCNS, DCPA, DCNA
¾ This equipment must not be used as an ‘emergency stop mechanism’ (see EN
60204, 9.2.5.4)
CAUTION
The connection of power, motor and control cables to the inverter must be carried
out as shown in Figure 2-14 on page 40, to prevent inductive and capacitive
interference from affecting the correct functioning of the inverter.
MICROMASTER 430
8
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Safety Instructions
Operation
WARNING
¾ MICROMASTERS operate at high voltages.
¾ When operating electrical devices, it is impossible to avoid applying hazardous
voltages to certain parts of the equipment.
¾ Emergency Stop facilities according to EN 60204 IEC 204 (VDE 0113) must
remain operative in all operating modes of the control equipment. Any
disengagement of the Emergency Stop facility must not lead to uncontrolled or
undefined restart.
¾ Wherever faults occurring in the control equipment can lead to substantial
material damage or even grievous bodily injury (i.e. potentially dangerous
faults), additional external precautions must be taken or facilities provided to
ensure or enforce safe operation, even when a fault occurs (e.g. independent
limit switches, mechanical interlocks, etc.).
¾ Certain parameter settings may cause the inverter to restart automatically after
an input power failure.
¾ Motor parameters must be accurately configured for motor overload protection
to operate correctly.
¾ This equipment is capable of providing internal motor overload protection in
accordance with UL508C section 42. Refer to P0610 and P0335, i2t is ON by
default. Motor overload protection can also be provided using an external
KTY84 or PTC.
¾ This equipment is suitable for use in a circuit capable of delivering not more
than 10,000 (Frame Size C) or 42,000 (Frame Sizes D to GX) symmetrical
amperes (rms), for a maximum voltage of 460 V when protected by an H, J or K
type fuse, a circuit breaker or self-protected combination motor controller (for
more details see Appendix F).
¾ This equipment must not be used as an ‘emergency stop mechanism’ (see EN
60204, 9.2.5.4)
Repair
WARNING
¾ Repairs on equipment may only be carried out by Siemens Service, by repair
centers authorized by Siemens or by authorized personnel who are
thoroughly acquainted with all the warnings and operating procedures contained
in this manual.
¾ Any defective parts or components must be replaced using parts contained in
the relevant spare parts list.
¾ Disconnect the power supply across all poles before opening the equipment for
access.
Dismantling & Disposal
CAUTION
¾ The inverter’s packaging is re-usable. Retain the packaging for future use or
return it to the manufacturer.
¾ Easy-to-release screw and snap connectors allow you to break the unit down
into its component parts. You can then re-cycle these component parts, dispose
of them in accordance with local requirements or return them to the
manufacturer.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
9
Electrostatic Sensitive Devices (ESD)
Issue 10/06
Electrostatic Sensitive Devices (ESD)
The device contains components which can be destroyed by electrostatic
discharge. These components can be easily destroyed if not carefully handled.
Before opening the cabinet/enclosure in which the device is located, you must
electrically discharge your body and apply the appropriate ESDS protective
measures. The cabinet/enclosure should be appropriately labeled.
If you have to handle electronic boards, please observe the following:
• Electronic boards should only be touched when absolutely necessary.
• The human body must be electrically discharged before touching an electronic
board.
• Boards must not come into contact with highly insulating materials - e.g. plastic
parts, insulated desktops, articles of clothing manufactured from man-made
fibers.
• Boards must only be placed on conductive surfaces.
• Boards and components should only be stored and transported in conductive
packaging (e.g. metalized plastic boxes or metal containers).
• If the packing material is not conductive, the boards must be wrapped with a
conductive packaging material, e.g. conductive foam rubber or household
aluminium foil.
The necessary ESD protective measures are clearly shown again in the following
diagram:
• a = Conductive floor surface
• b = ESD table
• c = ESD shoes
• d = ESD overall
• e = ESD chain
• f = Cubicle ground connection
d
d
b
b
d
e
e
f
a
c
Sitting
f
f
c
a
Standing
f
f
c
Standing / Sitting
MICROMASTER 430
10
a
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Table of Contents
Table of Contents
1
Overview ................................................................................................................ 15
1.1
The MICROMASTER 430....................................................................................... 16
1.2
Features.................................................................................................................. 17
2
Installation ............................................................................................................. 19
2.1
Installation after a Period of Storage ...................................................................... 21
2.2
Ambient operating conditions ................................................................................. 22
2.3
Mechanical installation............................................................................................ 24
2.4
Electrical installation ............................................................................................... 30
3
Commissioning ..................................................................................................... 43
3.1
Block diagram ......................................................................................................... 45
3.2
Commission modes ................................................................................................ 47
3.3
General operation ................................................................................................... 58
4
MICROMASTER 430 functions ............................................................................ 61
4.1
Frequency set point (P1000) .................................................................................. 63
4.2
Command sources (P0700).................................................................................... 63
4.3
OFF and brake function .......................................................................................... 64
4.4
Control modes (P1300)........................................................................................... 65
4.5
MICROMASTER 430 operating modes .................................................................. 66
4.6
Free Function Blocks (P2800 ff) ............................................................................. 70
4.7
Faults and Alarms ................................................................................................... 70
5
System parameters............................................................................................... 71
5.1
Introduction to MICROMASTER system parameters ............................................. 72
5.2
Parameter overview ................................................................................................ 73
6
Troubleshooting.................................................................................................... 75
6.1
Troubleshooting with the SDP ................................................................................ 76
6.2
Troubleshooting with the BOP-2............................................................................. 77
6.3
Fault messages....................................................................................................... 78
6.4
Alarm Messages ..................................................................................................... 78
7
MICROMASTER 430 specifications..................................................................... 79
8
Options .................................................................................................................. 87
8.1
Device-independent options ................................................................................... 87
8.2
Device-dependent options ...................................................................................... 87
9
Electro-magnetic compatibility (EMC) ................................................................ 89
9.1
Electro-magnetic compatibility ................................................................................ 90
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
11
Table of Contents
Issue 10/06
Appendices ................................................................................................................................ 95
A
Changing the Operator Panel .............................................................................. 95
B
Removing Front Covers ....................................................................................... 96
B.1
Removing Front Covers Frame Size C................................................................... 96
B.2
Removing Front Covers Frame Sizes D and E ...................................................... 97
B.3
Removing Covers Frame Size F............................................................................. 98
B.4
Removing Front Covers Frame Sizes FX and GX.................................................. 99
C
Removing the I/O Board..................................................................................... 100
D
Removing ‘Y’ Cap ............................................................................................... 101
D.1
Removing ‘Y’ Cap Frame Size C .......................................................................... 101
D.2
Removing ‘Y’ Cap Frame Sizes D and E.............................................................. 102
D.3
Removing ‘Y’ Cap Frame Sizes F......................................................................... 103
D.4
Removing ‘Y’ Cap Frame Sizes FX ...................................................................... 104
D.5
Removing ‘Y’ Cap Frame Sizes GX...................................................................... 105
E
Applicable Standards ......................................................................................... 106
F
Short circuit current rating (SCCR)................................................................... 107
G
List of Abbreviations .......................................................................................... 108
Index
.............................................................................................................................. 111
MICROMASTER 430
12
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Table of Contents
List of Illustrations
Figure 2-1
Forming ................................................................................................................................ 21
Figure 2-2
Ambient operating temperature ............................................................................................ 22
Figure 2-3
Installation altitude................................................................................................................ 22
Figure 2-4
Drill pattern for MICROMASTER 430 Frame Sizes C to F ................................................... 25
Figure 2-5
Installation dimensions for MICROMASTER 430 Frame size FX ......................................... 26
Figure 2-6
Installation dimensions for MICROMASTER 430 Frame size GX ........................................ 27
Figure 2-7
Installation of options for the electronic box.......................................................................... 29
Figure 2-8
MICROMASTER 430 Connection Terminals, Frame Sizes C to F ....................................... 33
Figure 2-9
MICROMASTER 430 connection drawing – frame size FX.................................................. 34
Figure 2-10
MICROMASTER 430 connection drawing – frame size GX ................................................. 35
Figure 2-11
Motor and Power Connections ............................................................................................. 36
Figure 2-12
Adaptation of fan voltage...................................................................................................... 37
Figure 2-13
Control terminals of MICROMASTER 430............................................................................ 38
Figure 2-14
Wiring Guidelines to Minimize the Effects of EMI ................................................................. 40
Figure 3-1
Inverter block diagram .......................................................................................................... 45
Figure 3-2
Configuration of the analogue input as a digital input ........................................................... 46
Figure 3-3
Panels available for the MICROMASTER 430 Inverter ........................................................ 47
Figure 3-4
DIP switch ............................................................................................................................ 47
Figure 3-5
Recommended wiring for the factory setting ........................................................................ 49
Figure 3-6
Buttons on the BOP-2........................................................................................................... 52
Figure 3-7
Changing parameters via the BOP-2.................................................................................... 53
Figure 3-8
Typical Motor Rating Plate Example .................................................................................... 57
Figure 3-9
Thermal overload protection................................................................................................. 59
Figure 4-1
Bypass circuit ....................................................................................................................... 66
Figure 4-2
Belt Failure Detection ........................................................................................................... 67
Figure 4-3
Motor Staging ....................................................................................................................... 68
Figure 4-4
Energy Saving Mode ............................................................................................................ 69
Figure 5-1
Parameter Overview............................................................................................................. 73
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
13
Table of Contents
Issue 10/06
List of Tables
Table 2-1
Dimensions and Torques of MICROMASTER 430............................................................... 28
Table 3-1
Default settings for operation using the SDP........................................................................ 48
Table 3-2
Default settings for operation using the BOP-2 .................................................................... 51
Table 6-1
Inverter conditions indicated by the LEDs on the SDP ......................................................... 76
Table 7-1
MICROMASTER 430 Performance Ratings ......................................................................... 80
Table 7-2
Dimensions, required cooling air flow and tightening torques for power terminals ............... 81
Table 7-3
Current reduction depending on pulse frequency................................................................. 82
Table 7-4
MICROMASTER 430 Specifications .................................................................................... 83
Table 9-1
General Industrial ................................................................................................................. 91
Table 9-2
Filtered Industrial .................................................................................................................. 91
Table 9-3
Filtered for Residential, Commercial and Light Industry ....................................................... 92
Table 9-4
Compliance Table ................................................................................................................ 93
MICROMASTER 430
14
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
1
1 Overview
Overview
This Chapter contains:
A summary of the major features of the MICROMASTER 430 range.
1.1
The MICROMASTER 430....................................................................................... 16
1.2
Features.................................................................................................................. 17
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
15
1 Overview
1.1
Issue 10/06
The MICROMASTER 430
The MICROMASTER 430s are a range of 3AC-frequency inverters for controlling
the speed of three phase AC motors. The various models available range from the
7,5 kW input to the 250 kW input.
The MICROMASTER 430 is especially well suited for use with pumps and
ventilators when used with its factory set functions and settings.
The inverters are microprocessor-controlled and use state-of-the-art Insulated Gate
BipoIar Transistor (IGBT) technology. This makes them reliable and versatile. A
special pulse-width modulation method with selectable Pulse frequency permits
quiet motor operation. Comprehensive protective functions provide excellent
inverter and motor protection.
MICROMASTER 430
16
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
1.2
1 Overview
Features
Main Characteristics
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
Easy installation
Easy commissioning
Rugged EMC design
Can be operated on IT line supplies
Fast repeatable response time to control signals
Comprehensive range of parameters enabling configuration for a wide range of
applications
Simple cable connection
Output relays
Analog outputs (0 – 20 mA)
6 Isolated and switchable NPN/PNP digital inputs
2 Analog inputs:
♦
AIN1: 0 – 10 V, 0 – 20 mA and -10 to +10 V
♦ AIN2: 0 – 10 V, 0 – 20 mA
The 2 analog inputs can be used as the 7th and 8th digital inputs
BiCo technology
Modular design for extremely flexible configuration
High switching frequencies for low-noise motor operation
Detailed status information and integrated message functions
External options for PC communications, Basic Operator Panel (BOP-2) and
PROFIBUS communications module
¾ Pump & Fan Features:
¾
¾
¾
¾
¾
¾
♦
Motor Staging (Control of additional drives via output relay)
♦
Energy Saving Mode
♦
Hand / Auto (manual / automatic) with BOP-2
♦
Belt failure detection (e.g. detects if pumps have run dry)
♦
Bypass
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
17
1 Overview
Issue 10/06
Performance Characteristics
¾ U/f control
♦
¾
¾
¾
¾
¾
¾
¾
¾
Linear U/f control with flux current control (FCC)for improved dynamic
response and motor control
♦ Multiple point U/f control
Automatic restart
Flying restart
Slip compensation
Fast Current Limitation (FCL) for trip-free operation
Motor holding brake
Built-in DC injection brake
Compound braking to improve braking performance
Setpoint input via:
♦
Analog inputs
♦
Communication interface
♦
Motorized potentiometer
♦ Fixed frequencies
¾ Ramp function generator
♦
With smoothing
♦ Without smoothing
¾ Technology controller (PID)
¾ parameter set switch-over
♦
Motor data sets (DDS)
♦ Command data sets and setpoint sources (CDS)
¾ Rating for operation with variable torque (VT)
¾ Free Function Blocks
Protection characteristics
¾
¾
¾
¾
¾
¾
Overvoltage/undervoltage protection
Overtemperature protection for the inverter
Ground fault protection
Short-circuit protection
i2t thermal motor protection
PTC/KTY for motor protection
Options
Refer to Chapter 8
MICROMASTER 430
18
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2
2 Installation
Installation
This Chapter contains:
¾
¾
¾
¾
General data relating to installation
Dimensions of Inverter
Wiring guidelines to minimize the effects of EMI
Details concerning electrical installation
2.1
Installation after a Period of Storage ...................................................................... 20
2.2
Ambient operating conditions ................................................................................. 22
2.3
Mechanical installation............................................................................................ 24
2.4
Electrical installation ............................................................................................... 29
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
19
2 Installation
Issue 10/06
WARNING
¾ Work on the device/system by unqualified personnel or failure to comply with
warnings can result in severe personal injury or serious damage to material.
Only suitably qualified personnel trained in the setup, installation,
commissioning and operation of the product should carry out work on the
device/system.
¾ Only permanently-wired input power connections are allowed. This equipment
must be grounded (IEC 536 Class 1, NEC and other applicable standards).
¾ If a Residual Current-operated protective Device (RCD) is to be used, it must be
an RCD type B. Machines with a three-phase power supply, fitted with EMC
filters, must not be connected to a supply via an ELCB (Earth Leakage CircuitBreaker EN 50178 Section 5.2.11.1).
¾ The following terminals can carry dangerous voltages even if the inverter is
inoperative:
♦ the power supply L/L1, N/L2, L3 resp. U1/L1, V1/L2, W1/L3
♦ the motor terminals U, V, W resp. U2, V2, W2
♦ and dependeing on the frame size the terminals DC+/B+, DC-, B-, DC/R+
resp. DCPS, DCNS, DCPA, DCNA
¾ Always wait 5 minutes to allow the unit to discharge after switching off before
carrying out any installation work.
¾ This equipment must not be used as an ‘emergency stop mechanism’ (see EN
60204, 9.2.5.4).
¾ The minimum size of the earth-bonding conductor must be equal to or greater
than the cross-section of the power supply cables.
CAUTION
The connection of power, motor and control cables to the inverter must be carried
out as shown in Figure 2-14 on page 40, to prevent inductive and capacitive
interference from affecting the correct functioning of the inverter.
MICROMASTER 430
20
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2.1
2 Installation
Installation after a Period of Storage
Following a prolonged period of storage, you must reform the capacitors in the
inverter. The requirements are listed below.
Frame Sizes C to F
Voltage
[%]
100
75
50
Storage period less than 1 year:
No action necessary
Storage period 1 to 2 years
Prior to energizing, connect to
voltage for one hour
Storage period 2 to 3 years
Prior to energizing, form
according to the curve
Storage period 3 and more years
Prior to energizing, form
according to the curve
Time t [h]
0,5
Figure 2-1
1
2
4
6
8
Forming
Frame Sizes FX and GX
Reforming the capacitors can be accomplished by applying 85% of the rated input
voltage for at least 30 minutes without load.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
21
2 Installation
2.2
Issue 10/06
Ambient operating conditions
Temperature
Frame Sizes G to F:
Frame Sizes FX and GX:
Permissible output current
[%]
Permissible output current
[%]
100
100
95
75
90
50
85
constant torque
25
-10
0
Figure 2-2
variable torque
10
20
30
60
40
50
Ambient temperature
[°C]
0
10
20
30
40 45 50 55 [°C]
Ambient temperature
Ambient operating temperature
Humidity Range
Relative air humidity ≤ 95 % Non-condensing
Altitude
If the inverter is to be installed at an altitude > 1000 m or > 2000 m above sea
level, derating will be required:
Permissible output current
100
%
85
80
Permissible input voltage
Frame Sizes
100
FX and GX
Frame Sizes
%
A to F
80
77
0
1000 2000
3000 4000
Installation altitude in m above sea level
Figure 2-3
2000
0
1000
3000 4000
Installation altitude in m above sea level
Installation altitude
Shock and Vibration
Do not drop the inverter or expose to sudden shock. Do not install the inverter in an
area where it is likely to be exposed to constant vibration.
Mechanical strength to EN 60721-3-3
¾ Deflection:
0.075 mm (10 ... 58 Hz)
¾ Acceleration:
9.8 m/s2 (> 58 ... 200 Hz)
MICROMASTER 430
22
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Electromagnetic Radiation
Do not install the inverter near sources of electromagnetic radiation.
Atmospheric Pollution
Do not install the inverter in an environment, which contains atmospheric pollutants
such as dust, corrosive gases, etc.
Water
Take care to site the inverter away from potential water hazards, e.g. do not install
the inverter beneath pipes that are subject to condensation. Avoid installing the
inverter where excessive humidity and condensation may occur.
Installation and cooling
CAUTION
The inverters MUST NOT be mounted horizontally.
The inverters can be mounted without any clearance at either side.
When mounting inverters one above the other, the specified environmental
conditions must not be exceeded.
Independent of this, these minimum distances must be observed.
¾ Frame Size C
above and below 100 mm
¾ Frame Size D, E
above and below 300 mm
¾ Frame Size F
above and below 350 mm
¾ Frame Size FX, GX above 250 mm
below 150 mm
in front 40 mm (FX), 50 mm (GX)
No equipment that could have a negative effect on the flow of cooling air should be
installed in this area. Make sure that the cooling vents in the inverter are positioned
correctly to allow free movement of air.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
23
2 Installation
2.3
Issue 10/06
Mechanical installation
WARNING
¾ To ensure the safe operation of the equipment, it must be installed and
commissioned by qualified personnel in full compliance with the warnings laid
down in these operating instructions.
¾ Take particular note of the general and regional installation and safety
regulations regarding work on dangerous voltage installations (e.g. EN 50178),
as well as the relevant regulations regarding the correct use of tools and
personal protective equipment (PPE).
¾ The mains input, DC and motor terminals, can carry dangerous voltages even if
the inverter is inoperative; wait 5 minutes to allow the unit to discharge after
switching off before carrying out any installation work.
¾ The inverters can be mounted without any clearance at either side. When
mounting inverters one above the other, the specified environmental conditions
must not be exceeded. Independent of this, these minimum distances must be
observed.
♦ Frame Size C
above and below 100 mm
♦ Frame Size D, E
above and below 300 mm
♦ Frame Size F
above and below 350 mm
♦ Frame Size FX, GX
above 250 mm
below 150 mm
in front 40 mm (FX), 50 mm (GX)
¾ If the front cover (Frame Sizes FX and GX) has been removed, the fan impeller
is exposed. There is danger of injury when the fan is running.
¾ IP20 protection is only against direct contact, always use these products within
a protective cabinet.
4
Removing from transport pallet (only for framesizes FX and GX)
During transport, the inverter is fastened on the transport pallet with the aid of two
iron brackets.
WARNING
Note that the center of gravity of the inverter is not in the middle of the unit. When
lifting the pallet, the unit can therefore suddenly change position and swing to the
side.
1. Fasten the hoisting crane cable to the hoisting eyes on the inverter (2 eyes
(see Figure 2-9 for frame size FX Figure 2-10 for frame size GX).
2. Remove the two retaining bolts at the top of the front cover.
3. Unscrew the bolts in the iron brackets on the transport pallet and lift the
inverter off the pallet.
4. Once installation has been completed and the inverter connected, fasten the
two retaining bolts for the front cover at the bottom side of the door.
4
MICROMASTER 430
24
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Frame Sizes C to F
FRAME SIZE C
FRAME SIZE D
Ø 5.5 mm
0.22"
Ø 17.5 mm
0.68"
204 mm
8.03"
486 mm
19.13"
174 mm
6.85"
235 mm
9.25"
FRAME SIZE E
FRAME SIZE F
Ø 17.5 mm
0.68"
Ø 15 mm
0.59"
616.4 mm
24.27"
810 mm
31.89"
with
filter
1110 mm
43.70"
235 mm
9.25"
300 mm
11.81"
Figure 2-4
Drill pattern for MICROMASTER 430 Frame Sizes C to F
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
25
2 Installation
Issue 10/06
Frame Size FX
Figure 2-5
Installation dimensions for MICROMASTER 430 Frame size FX
MICROMASTER 430
26
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Frame Size GX
Figure 2-6
Installation dimensions for MICROMASTER 430 Frame size GX
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
27
2 Installation
Table 2-1
Frame-Size
Issue 10/06
Dimensions and Torques of MICROMASTER 430
Overall Dimensions
Fixing Method
Tightening
Torque
mm
185 x 245 x 195
inch
7.28 x 9.65 x 7.68
4 x M5 Bolts
4 x M5 Nuts
4 x M5 Washers
2.5 Nm
with washers fitted
mm
275 x 520 x 245
inch
10.82 x 20.47 x 9.65
4 x M8 Bolts
4 x M8 Nuts
4 x M8 Washers
3.0 Nm
with washers fitted
4 x M8 Bolts
4 x M8 Nuts
4 x M8 Washers
3.0 Nm
with washers fitted
4 x M8 Bolts
4 x M8 Nuts
4 x M8 Washers
3.0 Nm
with washers fitted
6 M 8 Bolts
6 M 8 Nuts
6 M 8 Washers
13 Nm +30 %
with washers fitted
6 M 8 Bolts
6 M 8 Nuts
6 M 8 Washers
13 Nm +30 %
with washers fitted
C
Width x
Height x
Depth
D
Width x
Height x
Depth
Width x
Height x
Depth
mm
275 x 650 x 245
E
inch
10.82 x 25.59 x 9.65
mm
F
Width x
Height x
Depth
350 x 850 mm x 320
height with filter 1150
inch
13.78 x 33.46 x 12.60
height with filter 45.28
Width x
Height x
Depth
mm
326 x 1400 x 356
FX
inch
12,80 x 55,12 x 12,83
Width x
Height x
Depth
mm
326 x 1533 x 545
GX
inch
12,80 x 60,35 x 21,46
MICROMASTER 430
28
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2.3.1
2 Installation
Installing communication options and/or pulse encoder
evaluation module
Frame Size C
NOTE
When installing the following options – PROFIBUS module, DeviceNet module,
CANopen option module and/or pulses encoder evaluation module, the mounting
depth of the drive inverter is increased!
Please refer to the relevant Operating Instructions for the actual procedure.
Frame Sizes FX and GX
The front cover of the MICROMASTER 440 is designed so that the control module
(normally the SDP) is almost flush with the opening in the front cover.
If more than one option is to be installed in the electronic box, it is necessary to
position the entire electronic box further to the rear.
Installing the options
¾ Remove the front cover:
• Unscrew two screws at the bottom side of the front cover.
• Lift front cover up and out.
¾ Remove retaining screws on the electronic box.
¾ Screw on electronic box in correct installation position as shown in Figure 2-7
¾ Install additional options.
¾ Reinstall front cover.
Installation position 2
Installation position 1
Standard installation
Standard installation
Installation position 1
Installation position 2
Figure 2-7
Installation of options for the electronic box
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
29
2 Installation
2.4
Issue 10/06
Electrical installation
WARNING
¾ The inverter must always be grounded.
¾ To ensure the safe operation of the equipment, it must be installed and
commissioned by qualified personnel in full compliance with the warnings laid
down in these operating instructions.
¾ Take particular note of the general and regional installation and safety
regulations regarding work on dangerous voltage installations (e.g. EN 50178),
as well as the relevant regulations regarding the correct use of tools and
personal protective gear.
¾ Never use high voltage insulation test equipment on cables connected to the
inverter.
¾ The mains input, DC and motor terminals, can carry dangerous voltages even if
the inverter is inoperative; wait 5 minutes to allow the unit to discharge after
switching off before carrying out any installation work.
¾ If the front cover (Frame Sizes FX and GX) has been removed, the fan impeller
is exposed. There is danger of injury when the fan is running.
CAUTION
The control, power supply and motor leads must be laid separately. Do not feed
them through the same cable conduit/trunking.
MICROMASTER 430
30
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2.4.1
2 Installation
General
WARNING
The inverter must always be grounded. If the inverter is not grounded correctly,
extremely dangerous conditions may arise within the inverter which could prove
potentially fatal.
Operation with ungrounded (IT) supplies
Filtered
The use of MICROMASTER 4 inverters with built in filters is not allowed on IT
supplies.
Unfiltered
In the case of non-grounded networks, the 'Y' capacitor of the device must be
made ineffective. The procedure is described in Appendix D.
If the MICROMASTER is to remain in operation in non-grounded networks when a
ground fault occurs during the input or output phase, an output reactor must be
installed.
Operation with Residual Current Device (Frame Sizes C to F)
If an RCD (also referred to as ELCB or RCCB) is fitted, the MICROMASTER
inverters will operate without nuisance tripping, provided that:
¾ A type B RCD is used.
¾ The trip limit of the RCD is 300 mA.
¾ The neutral of the supply is grounded.
¾ Only one inverter is supplied from each RCD.
¾ The output cables are less than 50 m (screened) or 100 m (unscreened).
NOTE
The residual current operated circuit-breakers used must provide protection against
direct-current components in the fault current and must be suitable for briefly
suppressing power pulse current peaks. It is recommended to protect the
frequency inverter by fuse separately.
The regulations of the individual country (e.g. VDE regulations in Germany)
and the regional power suppliers must be observed!
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
31
2 Installation
2.4.2
Issue 10/06
Power and motor connections
WARNING
The inverter must always be grounded.
¾ Isolate the mains electrical supply before making or changing connections to
the unit.
¾ When synchronous motors are connected or when coupling several motors in
parallel, the inverter must be operated with voltage/frequency control
characteristic (P1300 = 0, 2 or 3).
CAUTION
After connecting the power and motor cables to the proper terminals, make sure
that the front covers have been replaced properly before supplying power to the
unit!
NOTICE
¾ Ensure that the appropriate circuit-breakers/fuses with the specified current
rating are connected between the power supply and inverter (see chapter 7,
Tables starting on page 82).
¾ Use Class 1 60/75oC copper wire only (for UL compliance). For tightening
torque see Table 7-2 on page 81.
Operation with long cables
All inverters will operate at full specification with cable lengths as follows:
Frame Sizes
C to F
FX and GX
screened
50 m
100 m
unscreened
100 m
150 m
Using the output chokes specified in catalogue DA 51.2, the following cable lengths
are possible for all frame sizes:
Supply Voltage
Frame Sizes
380 V … 400 V ± 10 %
401 V … 480 V ± 10 %
C
D to F
FX, GX
C
D to F
FX, GX
screened
200 m
200 m
300 m
100 m
200 m
300 m
unscreened
300 m
300 m
450 m
150 m
300 m
450 m
CAUTION
If using output chokes operation is only permissible with a pulse frequency of
4 kHz. Make shure that the automatic pulse frequency reductions are disabled.
Coercing required parameter adjusting: P1800 = 4 kHz , P0290 = 0 or 1.
Access to the power and motor terminals
Access to the power supply and motor terminals is possible by removing the front
covers (See Figure 2-8 to Figure 2-10). See also Appendix B.
After removing the front covers and exposing the terminals, complete power and
motor connections as shown Figure 2-11.
MICROMASTER 430
32
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Figure 2-8
MICROMASTER 430 Connection Terminals, Frame Sizes C to F
NOTE
The DC connections are for testing purposes only and have not been released for
operation by the user. No brake resistors etc. may be connected here.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
33
2 Installation
Issue 10/06
Hoisting eyes
Shield connection
Mains cable PE
Cable opening for
mains conection
U1/L1, V1/L2, W1/L3
Mains cable
Phase U1/L1, V1/L2, W1/L3
Connection to
Y-Capacitor
Connection DCPA, DCNA
Top adjustment rail
Top retaining screw
Connection DCPS, DCNS
Status Display Panel
Elektronic box
Bottom adjustment rail
Bottom retaining screw
Fan screws
Fan
Shield connection
control leads
Fan fuses
Transformer adaption
Motor cable
Phase U2, V2, W2
Motor cable
PE Shield connection
Figure 2-9
MICROMASTER 430 connection drawing – frame size FX
MICROMASTER 430
34
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Hoisting eyes
Shield connection
Mains cable PE
Cable opening for
mains conection
U1/L1, V1/L2, W1/L3
Mains cable
Phase U1/L1, V1/L2, W1/L3
Connection to
Y-Capacitor
Connection DCPA, DCNA
Top adjustment rail
Top retaining screw
Connection DCPS, DCNS
Status Display Panel
Elektronic box
Bottom adjustment rail
Bottom retaining screw
Fan screws
Fan
Shield connection
control leads
Fan fuses
Transformer adaption
Motor cable
Phase U2, V2, W2
Motor cable
PE Shield connection
Figure 2-10
MICROMASTER 430 connection drawing – frame size GX
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
35
2 Installation
Issue 10/06
Frame Sizes C to F
L3
L2
L1
Contactor
Optional
line choke
optinal
filter
MICROMASTER 1)
Motor
Fuse
L3
U
L2
V
W
L1
PE
PE
PE
PE
1) with and without filter
Frame Sizes FX and GX
L3
L2
L1
Contactor
Optional
filter
Optional
line choke
MICROMASTER 2)
Motor
Fuse
L3
U
L2
V
L1
W
PE
PE
PE
3)
2) without filter
3) the commutation choke is to be earthed using the designated earthing point
Figure 2-11 Motor and Power Connections
MICROMASTER 430
36
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Adaptation of fan voltage (only for framesize FX and GX)
A transformer is installed to adapt the existing line voltage to the fan voltage.
It may be necessary to reconnect the transformer terminals on the primary side to
coincide with the existing line power.
0V 1L380V
1L400V 1L440V
1L480V
-
Connect according input voltage
Figure 2-12 Adaptation of fan voltage
CAUTION
If the terminals are not reconnected to the actually present line voltage, the fan
fuses can blow.
Replacement for fan fuses
Frame size
FX (90 kW CT)
FX (110 kW CT)
GX (132-200 kW CT)
Fuses (2 each)
Recommended fuses
1 A / 600 V / slow-acting
Cooper-Bussmann FNQ-R-1, 600 V
or comparable fuse
2,5 A / 600 V / slow-acting
Ferraz Gould Shawmut ATDR2-1/2, 600 V
or comparable fuse
4 A / 600 V / slow-acting
Ferraz Gould Shawmut ATDR4, 600 V
or comparable fuse
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
37
2 Installation
2.4.3
Issue 10/06
Control terminals
Permitted cable diameters: 0.08 … 2.5 mm2 (AWG: 28 … 12)
Terminal Designation
Function
1
−
Output +10 V
2
−
Output 0 V
3
ADC1+
Analog input 1 (+)
4
ADC1-
Analog input 1 (-)
5
DIN1
Digital input 1
6
DIN2
Digital input 2
7
DIN3
Digital input 3
8
DIN4
Digital input 4
9
−
Isolated output +24 V / max. 100 mA
10
ADC2+
Analog input 2 (+)
11
ADC2-
Analog input 2 (-)
12
DAC1+
Analog output 1 (+)
13
DAC1-
Analog output 1 (-)
14
PTCA
Connection for PTC / KTY84
15
PTCB
Connection for PTC / KTY84
16
DIN5
Digital input 5
17
DIN6
Digital input 6
18
DOUT1/NC
Digital output 1 / NC contact
19
DOUT1/NO
Digital output 1 / NO contact
20
DOUT1/COM
Digital output 1 / Changeover contact
21
DOUT2/NO
Digital output 2 / NO contact
22
DOUT2/COM
Digital output 2 / Changeover contact
23
DOUT3/NC
Digital output 3 / NC contact
24
DOUT3/NO
Digital output 3 / NO contact
25
DOUT3/COM
Digital output 3 / Changeover contact
26
DAC2+
Analog output 2 (+)
27
DAC2-
Analog output 2 (-)
28
−
Isolated output 0 V / max. 100 mA
29
P+
RS485 port
30
N−
RS485 port
Figure 2-13
Control terminals of
MICROMASTER 430
MICROMASTER 430
38
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2.4.4
2 Installation
Avoiding Electro-Magnetic Interference (EMI)
The inverters are designed to operate in an industrial environment where a high
level of EMI can be expected. Usually, good installation practices will ensure safe
and trouble-free operation. If you encounter problems, follow the guidelines stated
below.
Action to Take
¾ Ensure that all equipment in the cubicle is well grounded using short, thick
grounding cable connected to a common star point or busbar.
¾ Make sure that any control equipment (such as a PLC) connected to the
inverter is connected to the same ground or star point as the inverter via a
short thick link.
¾ Connect the return ground from the motors controlled by the inverters directly
to the ground connection (PE) on the associated inverter.
¾ Flat conductors are preferred as they have lower impedance at higher
frequencies.
¾ Terminate the ends of the cable neatly, ensuring that unscreened wires are as
short as possible.
¾ Separate the control cables from the power cables as much as possible,
using separate trunking, if necessary at 90º to each other.
¾ Whenever possible, use screened leads for the connections to the control
circuitry.
¾ Ensure that the contactors in the cubicle are suppressed, either with R-C
suppressors for AC contactors or 'flywheel' diodes for DC contactors fitted to
the coils. Varistor suppressors are also effective. This is important when the
contactors are controlled from the inverter relay.
¾ Use screened or armored cables for the motor connections and ground the
screen at both ends using the cable clamps.
WARNING
Safety regulations must not be compromised when installing inverters!
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
39
2 Installation
2.4.5
Issue 10/06
Screening Methods
Frame Size C
For frame size C the Gland Plate Kit is supplied as an option. It allows easy and
efficient connection of the necessary screening. See the Gland Plate Installation
Instructions contained on the Document CD-ROM, supplied with the MM430.
Screening without a Gland Plate
Should a Gland Plate not be available, then the inverter can be screened using the
methodology shown in Figure 2-14.
1
2
3
4
5
6
7
Mains power input
Control cable
Motor cable
Footprint filter
Metal back plate
Use suitable clips to fix motor and control cable screens securely to metal back plate
Screening cables
Figure 2-14
Wiring Guidelines to Minimize the Effects of EMI
MICROMASTER 430
40
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
2 Installation
Frame Sizes D and E
The Gland Plate is factory fitted. If the installation conditions are restricted, the
shield of the motor cable can also be attached outside the cabinet, as shown in
Figure 2-14, for example.
Frame size F
The gland plate for the control cables is factory-fitted.
Devices without filter: The shield of the motor cable must be attached outside the
cabinet, as shown in Figure 2-14, for example.
Devices with filter:
The gland plate for the motor cable is factory-fitted.
Frame Sizes FX and GX
Attach the shields for the control cable as shown in the connection overview (see
Figure 2-9 and Figure 2-10) to the marked shield connection over a large surface.
Twist the shields of the motor cables and screw them to the PE connection for the
motor cable.
When using an EMI filter, a power commutating choke is required. The wire shields
should be fastened to the metallic mounting surface as close as possible to the
components.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
41
2 Installation
Issue 10/06
MICROMASTER 430
42
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3
3 Commissioning
Commissioning
This Chapter contains:
¾ A schematic diagram of the MICROMASTER 430
¾ An overview of the commissioning options and the display and operator panels
¾ An overview of quick commissioning of the MICROMASTER 430
3.1
Block diagram ......................................................................................................... 45
3.2
Commission modes ................................................................................................ 46
3.3
General operation ................................................................................................... 56
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
43
3 Commissioning
Issue 10/06
WARNING
¾ MICROMASTERS operate at high voltages.
¾ When operating electrical devices, it is impossible to avoid applying hazardous
voltages to certain parts of the equipment.
¾ The following terminals can carry dangerous voltages even if the inverter is
inoperative:
♦ the power supply L/L1, N/L2, L3 resp. U1/L1, V1/L2, W1/L3
♦ the motor terminals U, V, W resp. U2, V2, W2
♦ and depending on the frame size the terminals DC+/B+, DC-, B-, DC/R+
resp. DCPS, DCNS, DCPA, DCNA
¾ Emergency Stop facilities according to EN 60204 IEC 204 (VDE 0113) must
remain operative in all operating modes of the control equipment. Any
disengagement of the Emergency Stop facility must not lead to uncontrolled or
undefined restart.
¾ Wherever faults occurring in the control equipment can lead to substantial
material damage or even grievous bodily injury (i.e. potentially dangerous
faults), additional external precautions must be taken or facilities provided to
ensure or enforce safe operation, even when a fault occurs (e.g. independent
limit switches, mechanical interlocks, etc.).
¾ Certain parameter settings may cause the inverter to restart automatically after
an input power failure.
¾ Motor parameters must be accurately configured for motor overload protection
to operate correctly.
¾ This equipment is capable of providing internal motor overload protection in
accordance with UL508C section 42. Refer to P0610 and P0335, i2t is ON by
default. Motor overload protection can also be provided using an external
KTY84 or PTC.
¾ This equipment is suitable for use in a circuit capable of delivering not more
than 10,000 (Frame Size C) or 42,000 (Frame Sizes D to GX) symmetrical
amperes (rms), for a maximum voltage of 460 V when protected by an H, J or K
type fuse, a circuit breaker or self-protected combination motor controller (for
more details see Appendix F).
This equipment must not be used as an ‘emergency stop mechanism’ (see EN
60204, 9.2.5.4).
CAUTION
Only qualified personnel may enter settings in the control panels. Particular
attention must be paid to safety precautions and warnings at all times.
MICROMASTER 430
44
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3.1
3 Commissioning
Block diagram
PE
3 AC 380 - 480 V
PE
+10 V
1
L/L1, N/L2,L3
or
L1, L2, L3
0V
2
ADC1+
3
ADC1-
BOP link
A/D
4
RS232
ADC2+
10
ADC2-
A/D
150.00
Hz
I
11
External 24 V
0
5
5
6
6
7
7
8
8
~
Opto Isolation
DIN2
DIN2
DIN3
DIN3
DIN4
DIN4
DIN5
DIN5
16
16
17
17
P
BOP-2
DIN1
DIN1
Fn
Jog
=
Frame sizes
C to F
B+/DC+
DC-
DIN6
DIN6
Output +24 V
max. 100 mA
(isolated)
Output 0 V
max. 100 mA
(isolated)
PNP
9
or
NPN
28
28
PTCA
Motor
PTC
KTY84
A/D
14
PTCB
DCNA
Frame sizes
FX and GX
DCPA
CPU
15
DCNS
DAC1+
0 - 20 mA
max. 500 Ω
12
DAC1-
DCPS
D/A
13
=
DAC2+
0 - 20 mA
max. 500 Ω
Connections are only for measuring purposes
≥ 4.7 kΩ
+
_ 24 V
SI
26
DAC2-
3~
D/A
27
COM
20
Relay1
19
Not
used
NO
50 Hz
1
2
DIP switch
(on Control Board)
NC
18
30 V DC / 5 A (resistive)
250 V AC / 2 A (inductive)
COM
Relay2
22
NO
0 - 20 mA
current
0 - 10 V
voltage
21
COM
25
Relay3
24
60 Hz
ADC ADC
1
2
DIP switch
(on I/O Board)
1
2
NO
NC
23
P+
29
N-
RS485
COM link
30
CB
Option
PE
U,V,W
automatic
M
Figure 3-1 Inverter block diagram
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
45
3 Commissioning
3.1.1
Issue 10/06
Standard settings for the terminals
See Figure 3-2.
3.1.2
Analogue inputs
Analogue input 1 (AIN1) can be used with:
0 - 10 V, 0 - 20 mA and -10 V to +10 V
Analogue input 2 (AIN2) can be used with:
0 - 10 V and 0 - 20 mA
The analog input circuit can be alternatively configured to provide additional digital
inputs (DIN7 & DIN8) as shown:
1
1
2
2
3
10
DIN7
DIN8
4
Figure 3-2
11
Configuration of the analogue input as a digital input
When an analogue input is configured as a digital input the threshold values are as
follows:
1.75 V DC = OFF
3.70 V DC = ON
Terminal 9 (24 V) can also be used to drive the analog inputs when used as digital
inputs. Terminals 2 and 28 (0 V) must be linked together.
MICROMASTER 430
46
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3.2
3 Commissioning
Commission modes
In the standard version, the MICROMASTER 430 is fitted with the Status Display
Panel (SDP) (see Figure 3-3) with which it is possible to use the inverter with the
pre-assigned factory settings for a large range of applications. If these factory
settings are not suitable, you can adapt them to suit your equipment conditions
using the Basic Operator Panel-2 (BOP-2) (see Figure 3-3). The BOP-2 are
available as options. You can also adjust the factory settings using the PC IBN tool.
This software is available on the CD ROM which comes with the documentation of
the unit.
ATTENTION
MICROMASTER 430 can only be operated with the BOP-2.
It is not possible to use BOP or AOP.
SDP
Status Display Panel
Figure 3-3
BOP-2
Basic Operator Panel
Panels available for the MICROMASTER 430 Inverter
For notes on replacing the operator panels please refer to the corresponding
appendix A to this manual.
NOTICE
Adjusting the motor frequency 50/60 Hz: The DIP switch to adjust the motor frequency is located below the I/O board (for removing the I/O board, see appendix C)
The inverter is delivered as follows:
¾ DIP switch 2:
♦
Off position: European
defaults (50 Hz, kW etc.)
DIP Switch for
motor frequency
♦
On position: North American
defaults (60 Hz, hp etc.)
¾ DIP switch 1:
Not for customer use.
Figure 3-4
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
DIP switch
47
3 Commissioning
3.2.1
Issue 10/06
Commissioning with the SDP
The SDP has two LEDs on the front which display the
current operating status of the inverter (see Section 6.1).
When the SDP is used, the presettings of the inverter
must be compatible with the following motor data:
¾ Rated motor power
¾ Motor voltage
¾ Rated motor current
¾ Rated motor frequency
(A conventional Siemens motor is recommended)
In addition, the following conditions must be met:
¾ Linear V/f motor speed controlled by an analog potentiometer.
¾ Maximum speed 1500 rpm at 50 Hz (1800 rpm at 60 Hz); can be controlled by
a potentiometer via the analog inputs of the inverter.
¾ Ramp-up time = 10 s
¾ Ramp-down time = 30 s
Settings for more complex applications can be found in the parameter list and in
Section 3.2.2 "Commission Overview with BOP-2".
Table 3-1
*
Default settings for operation using the SDP
Terminals
Parameter
Default Operation
Digital Input 1
5
P0701 = ‘1’
ON right
Digital Input 2 *
6
P0702 = ‘12’
Reverse
Digital Input 3
7
P0703 = ‘9’
Fault Acknowledge
Digital Input 4
8
P0704 = ‘15’
Fixed Frequency
Digital Input 5
16
P0705 = ‘15’
Fixed Frequency
Digital Input 6
17
P0706 = ‘15’
Fixed Frequency
Digital Input 7
Via AIN1
P0707 = ‘0’
Inactive
Digital Input 8
Via AIN2
P0708 = ‘0’
Inactive
The standard setting for the change of rotation direction is as inhibited.
(Parameter 1110)
MICROMASTER 430
48
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
Basic operation with SDP
With the SDP fitted, the following is possible:
¾ Start and stopping the motor (DIN1 via external switch)
¾ Fault Reset
(DIN3 via external switch)
¾ Presetting frequency setpoint (via ADC1 with external potentiometer
default setting of the ADC: Voltage input)
¾ Output frequency actual value (via D/A converter,
D/A converter output: Current output)
Controlling the speed of the motor is accomplished by connecting the analog inputs
as shown in the Figure 3-5. The potentiometer and the external switches can be
connected through the drive inverter internal power supply.
Figure 3-5
Recommended wiring for the factory setting
If settings have to be made which go beyond the factory setting, then depending on
the complexity of the application, when commissioning the drive system, the
particular function description as well as the parameter list including function charts
must be carefully taken into consideration.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
49
3 Commissioning
3.2.2
Issue 10/06
Commission Overview with BOP-2
Prerequisites
Mechanical and electrical Installation are completed.
Setting the motor frequency
DIP Switch 2: OFF = 50 Hz / ON = 60 Hz
Power ON
Quick Commissioning P0010 = 1
See Section 3.2.3.1
Further Commissioning via P0004 and P0003
An overview of the parameter structure is given in
Section 5.1
For a detailed description of the parameter, see the
Parameter List.
NOTES
We recommend the commissioning according this scheme.
MICROMASTER 430
50
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
3.2.2.1 Commissioning with the BOP-2
You can alter parameter values via the BOP-2. To set parameters on this panel,
you must remove the SDP and attach the BOP-2 (see
Appendix A).
The BOP-2 features a five-digit, seven-segment display
for showing parameter numbers and values, alarm and
fault messages and setpoints and actual values.
Parameter sets cannot be saved via the BOP-2.
Table 3-2 shows the factory default settings for operation
via the BOP-2.
NOTICE
¾ The BOP-2 motor control functions are disabled by default. To control the motor
via the BOP-2, parameter P0700 should be set to 1 and P1000 set to 1.
¾ The BOP-2 can be fitted to and removed from the inverter whilst power is
applied.
¾ If the BOP-2 has been set as the I/O control (P0700 = 1), the drive will stop if
the BOP-2 is removed.
Table 3-2
Default settings for operation using the BOP-2
Parameter
Meaning
Default Europe (North America)
P0100
Operating Mode Europe/US
50 Hz, kW (60 Hz, hp)
P0307
Power (rated motor)
Dimension kW (Hp) depending on setting of P0100.
[Value depending on variant]
P0310
Motor frequency rating
50 Hz (60 Hz)
P0311
Motor speed rating
1395 (1680) rpm [depending on variant]
P1082
Maximum Motor Frequency
50 Hz (60 Hz)
ATTENTION
MICROMASTER 430 can only be operated using a BOP-2 bedient werden.
If a BOP or AOP is used, the following is shown on the display
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
.
51
3 Commissioning
Issue 10/06
Buttons on the BOP-2
Panel/Button
Function
Indicates
Status
Effects
The LCD displays the settings currently used by the converter.
Start motor
Pressing the button starts the converter. This button is disabled by
default. To enable this button set P0700 = 1.
Stop motor
OFF1 Pressing the button causes the motor to come to a standstill
at the selected ramp down rate. Disabled by default; to
enable set P0700 = 1.
OFF2 Pressing the button twice (or once long) causes the motor to
coast to a standstill.
This function is always enabled.
Manual
mode
The customer terminal strip (CD S2) and the operating panel (BOP2) are sources for commands and set values
Automatic
mode
The customer’s terminal strip (CD S1) or the serial (US S) or field bus
interface (e.g. PROFIBUS) are sources for commands and set
values.
This button can be used to view additional information.
Functions
Pressing and holding the button for 2 seconds from any parameter
during operation, shows the following:
1. DC link voltage (indicated by d – units V).
2. Output current. (A)
3. Output frequency (Hz)
4. Output voltage (indicated by o – units V).
5. The value selected in P0005 (If P0005 is set to show any of the
above (1 - 4) then this will not be shown again).
Additional presses will toggle around the above displays.
Jump Function
From any parameter (rXXXX or PXXXX) a short press of the Fn
button will immediately jump to r0000, you can then change another
parameter, if required. Upon returning to r0000, pressing the Fn
button will return you to your starting point.
Quit
In case of a fault or alarm the
button resets the fault or alarm
message on the operator panel display.
Access
parameters
Pressing this button allows access to the parameters.
Increase
value
Pressing this button increases the displayed value.
Decrease
value
Pressing this button decreases the displayed value.
Figure 3-6 Buttons on the BOP-2
MICROMASTER 430
52
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
Changing parameters with the BOP-2
The procedure for changing the value of parameter P0004 is described below.
Modifying the value of an indexed parameter is illustrated using the example of
P0719. Follow exactly the same procedure to alter other parameters that you wish
to set via the BOP-2.
Changing P0004 – parameter filter function
Step
1
Press
to access parameters
2
Press
until P0004 is displayed
3
Press
to access the parameter value level
4
Press
or
5
Press
to confirm and store the value
Result on display
to the required value
Changing P0719 an indexed parameter
Selection of command/setpoint source
Step
1
Press
to access parameters
2
Press
until P0719 is displayed
3
Press
to access the parameter value level
4
Press
to display current set value
5
Press
or
6
Press
to confirm and store the value
7
Press
until r0000 is displayed
8
Press
to return the display to the standard
drive display (as defined by the customer)
Result on display
to the required value
Figure 3-7 Changing parameters via the BOP-2
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
53
3 Commissioning
Issue 10/06
NOTES
In some cases - when changing parameter values - the display on the BOP-2
shows
. This means the inverter is busy with tasks of higher priority.
Changing single digits in Parameter values
For changing the parameter value rapidly, the single digits of the display can be
changed by performing the following actions:
Ensure you are in the parameter value changing level (see "Changing parameters
with BOP-2").
1. Press
(function button), which causes the right hand digit to blink.
2. Change the value of this digit by pressing
/
.
(function button) again causes the next digit to blink.
3. Press
4. Perform steps 2 to 4 until the required value is displayed.
5. Press the
to leave the parameter value changing level.
NOTES
The function button may also be used to acknowledge a fault condition
3.2.3
Commissioning functions with BOP-2
3.2.3.1 Quick commissioning (P0010=1)
Mechanical and electrical installation of the inverter must be completed before
running „Quick Commissioning“.
It is important that parameter P0010 is used for commissioning and P0003 is used
to select the access level.
There are three user levels, standard, extended and expert. The lower the access
level fewer parameters can be seen while performing Quick commissioning. The
values for these parameters are either the default settings or are calculated during
quick commissioning.
Quick commissioning includes motor and ramp setting parameters.
Quick Commissioning concludes with P3900, which, when set to 1, will perform the
necessary motor calculations and clear all other parameters (not included in
P0010=1) to the default settings. After completing Quick Commissioning with
P3900 = 1, the inverter is then ready to run; this will only happen in the Quick
Commissioning mode.
MICROMASTER 430
54
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
Flow chart Quick Commissioning
Access level
P0003 User access level
1
Standard
2
Extended
3
Expert
2)
1
P0010 Start Quick Commissioning
0
Ready to Run
1
Quick Commissioning
30 Factory Setting
2)
P0100 Operation for Europe/N. America
0
Power in kW; f default 50 Hz
1
Power in hp; f default 60 Hz
2
Power in kW; f default 60 Hz
1
1
NOTE
Settings 0 and 1 should be changed using the DIP
switches to allow permanent setting. The DIP
switches should be used to create permanent
settings. After a mains break the DIP switch settings
overide the parameter settings.
1)
P0309 Rated motor efficiency 1)
Setting range: 0,0 - 99,9 %
Nominal motor efficiency in % from rating plate. .
Visible only when P0100 = 1, ( motor power in hp).
2
P0310 Rated Motor Frequency 1)
Setting range: 12 Hz - 650 Hz
Nominal motor frequency (Hz) from rating plate.
1
P0311 Rated Motor Speed 1)
Setting range: 0 - 40.000 U/min
Nominal motor speed (rpm) from rating plate.
1
P0320 Motor magnetizing current
Setting range: 0.0 - 99.0 %
Motor magnetizing current (%) relative to the rated
motor current (P0305).
3
P0335 Motor cooling
0 Self-cooled
1 Force-cooled
2 Self-cooled and internal fan
3 Force-cooled and internal fan
3
P0304 Rated Motor Voltage
Setting range: 10 V - 2000 V
Nominal motor voltage (V) from rating plate.
1
P0305 Rated Motor Current 1)
Setting range: 0 - 2 x inverter rated current (A)
Nominal motor current (A) from rating plate.
1
P0500 Technological application
0 Constant torque
1 Pumps and fans
3
P0307 Rated Motor Power 1)
Setting range: 0,01 kW - 2000 kW
Nominal motor power (kW) from rating plate.
If P0100 = 1, values will be in hp.
1
P0640 Motor overload factor
Setting range: 10.0 - 400.0 %
Motor overload current limit [%] relative to P0305
(rated motor current).
3
P0308 Rated motor cosPhi 1)
1
Setting range: 0,000 - 1,000
Nom. motor power factor (cosPhi) from rating plate .
Visible only when P0100 = 0, 2, (motor power in kW).
P0700 Selection of Command Source
0
Factory Setting
1
BOP-2
2
Terminals (Digital Inputs)
2)
1
Note
If P0700 = 2 is selected, the function of the digital
inputs can be determind via P0701 to P0708. P0701
to P0708 = 99 enables the BICO-parameterization for
the digital inputs.
1) Motor-specific parameters – see motor rating plate.
2) The parameters offer more setting options than listed here. See Parameter List for further setting
options.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
55
3 Commissioning
P1000 Selection of Frequency Setpoint
1 Motor potentiometer setpoint
2 Analog setpoint 1
3 Fixed frequency setpoint
7 Analog setpoint 2
Issue 10/06
2)
1
Note
For additional settings for setpoint see Parameter
List.
If P1000 = 1 the selection depends on the settings of
P0700 to P0708
P1910 Select motor data identification:
0 Disabled
1 Identification of all parameters with
parameter change
Note
Motor identification must be performed with a cold
motor (20 °C). If the ambient temperature is not within
the range of 20°C (+5°C), P0625 Ambient motor
temperature must be updated
P1910 = 0
P1910 = 1
P1080 Min. Motor Frequency
1
Setting range: 0 - 650 Hz
Sets minimum motor frequency (0 - 650 Hz) at which
the motor will run irrespective of the frequency setpoint. The value is valid for both motor directions.
P1082 Max. Motor Frequency
1
Setting range: 0 - 650 Hz
Sets maximum motor frequency (0 - 650 Hz) at which
the motor will run irrespective of the frequency setpoint. The value is valid for both motor directions.
P1120 Ramp-Up Time
1
Setting range: 0 - 650 s
Time taken for the motor to accelerate from standstill
up to maximum motor frequency.
P1121 Ramp-Down Time
Setting range: 0 - 650 s
Time taken for motor to decelerate from maximum
motor frequency down to standstill.
1
P1135 OFF3 ramp-down time
Setting range: 0 - 650 s
Defines the ramp down time from the maximum
frequency to standstill for the OFF3 command.
2
P1300 Control mode
0
V/f with linear charac.
1
V/f with FCC
2
V/f with parabolic charac.
3
V/f with programmable charac.
5
V/f for textile applications
6
V/f with FCC for textile applications
19 V/f control with independent voltage setpoint
3
2
Alarm A0541
Motor data idendification active.
P3900 End Quick Commissioning
0
End Quick Commissioning without motor
calculation or factory reset.
1
End Quick Commissioning with motor
calculation and factory reset.
2
End Quick Commissioning with motor
calculation and with I/O reset.
3
End Quick Commissioning with motor
calculation but without I/O reset.
P3900 = 1,2
1
P3900 = 3
Switch on Motor, Motor data identification
starts. After completing motor identification, Alarm message A0541 disappears.
Quick Commissioning complete, the inverter goes
into ready-to-run state
2) The parameters offer more setting options than listed here. See Parameter List for further setting
options.
MICROMASTER 430
56
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
Motor data for parameterization
Figure 3-8 Typical Motor Rating Plate Example
(The details given on the rating plate are only examples)
NOTICE
¾ P0308 & P0309 are only visible if P0003 ≥ 2. Only one of the parameters is
shown depending on the settings of P0100.
¾ P0307 indicates kW or HP depending upon the setting of P0100. For detailed
information, please see the Parameter List.
¾ Changing motor parameters is not possible unless P0010=1.
¾ Ensure that the inverter is configured correctly to the motor.
¾ Observe the motor's star/delta connection arrangement!
3.2.4
Reset to Factory default
To reset all parameters to the factory default settings; the following parameters
should be set as follows (BOP-2 or Communication Option needed):
1. Set P0010=30.
2. Set P0970=1.
NOTE
The reset process can take up to 3 minutes to complete.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
57
3 Commissioning
3.3
Issue 10/06
General operation
For a full description of standard and extended parameters, please refer to the
Parameter List.
NOTICE
1. The inverter does not have a main power switch and is live when the mains
supply is connected. It waits, with the output disabled, until the RUN button is
pressed or for the presence of a digital ON signal at terminal 5 (rotate right).
2. If a BOP-2 is fitted and the output frequency is selected to be displayed (P0005
= 21) the corresponding setpoint is displayed approximately every 1.0 seconds
while the inverter is stopped.
3. The inverter is programmed at the factory for standard applications on Siemens
four-pole standard motors that have the same power rating as the inverters.
When using other motors it is necessary to enter the specifications from the
motor's rating plate. See Figure 3-8 for details on how to read motor data.
4. Changing motor parameters is not possible unless P0010 = 1.
5. Before initing a run, You must set P0010 back to 0.
Basic operation with the BOP-2
Prerequisites
¾ P0010 = 0 (in order to initiate the run command correctly).
¾ P0700 = 1 (enables the start/stop button on the BOP-2).
¾ P1000 = 1 (this enables the motor potentiometer setpoints).
1.
Press the green Button
2.
Press the Button
50 Hz.
3.
When the inverter reaches 50 Hz, press the Button
display is decreased.
4.
Press button
, to activate manual mode.
5.
Press button
, to activate automatic mode.
6.
The red button stops the motor
to start the motor.
while the motor is turning. Motor speed increases to
. Motor speed and
.
NOTE
Three Command data sets (CDS) are available. The Hand/Auto-Button on the
BOP-2 toggles between CDS 1 and CDS 2. If CDS 3 is selected (via P0811), the
Hand/Auto-Button on the BOP-2 is inactive. For further details see the Parameter
List.
MICROMASTER 430
58
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
3 Commissioning
External motor thermal overload protection
When operated below rated speed, the cooling effect of fans fitted to the motor
shaft is reduced. Consequentially, most motors require de-rating for continuous
operation at low frequencies. To ensure that the motors are protected against
overheating under these conditions, a PTC temperature sensor must be fitted to
the motor and connected to the inverter control terminals.
5V
574 Ω
Kl. 14
A
PTC/
KTY
D
Kl. 15
PTC-Auslöseschwelle = 4 V
PTC-Charakteristik für 1LG/1LA-Motoren
KTY84-Charakteristik
Figure 3-9 Thermal overload protection
With PTC sensor (P0601 = 1)
If the PTC in the motor is connected to the MICROMASTER 430 control terminals
14 (PTCA) and 15 (PTCB) and the PTC function enabled by setting P0601 = 1,
then the MICROMASTER 430 will operate as normal providing the resistance at
the terminals remains below approximately 1500 Ω. If this value is exceeded, the
inverter indicates a warning A0511 and then a fault F0011. The actual resistance
value at which this occurs will not be less than 1000 Ω, and not more than 2000 Ω.
With KTY84 sensor (P0601 = 2)
The KTY84 has to be connected so that the diode is forward biased; that is the
anode is connected to terminal 14 (PTCA) and the cathode to terminal 15 (PTCB).
If the temperature monitoring function is enabled by setting P0601 = 2, the
temperature of the sensor (and therefore the motor windings) is written to
parameter r0035. The threshold motor temperature can now be set using
parameter P0604 (default setting 130 °C).
Connection failure
If the connection to the PTC or KTY84 sensor becomes open circuit or short circuit,
a fault will be indicated, and by default the drive will trip.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
59
3 Commissioning
Issue 10/06
MICROMASTER 430
60
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
4
4 MICROMASTER 430 functions
MICROMASTER 430 functions
This chapter contains:
¾ a description of the different procedures to control the inverter
¾ a summary of the control types of the inverter.
4.1
Frequency set point (P1000) .................................................................................. 63
4.2
Command sources (P0700).................................................................................... 63
4.3
OFF and brake function .......................................................................................... 64
4.4
Control modes (P1300)........................................................................................... 65
4.5
MICROMASTER 430 operating modes .................................................................. 66
4.6
Free Function Blocks (P2800 ff) ............................................................................. 70
4.7
Faults and Alarms ................................................................................................... 70
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
61
4 MICROMASTER 430 functions
Issue 10/06
WARNING
♦ When operating electrical devices, certain parts of these devices are always
live.
¾ The following terminals can carry dangerous voltages even if the inverter is
inoperative:
♦ the power supply L/L1, N/L2, L3 resp. U1/L1, V1/L2, W1/L3
♦ the motor terminals U, V, W resp. U2, V2, W2
♦ and depending on the frame size the terminals DC+/B+, DC-, B-, DC/R+
resp. DCPS, DCNS, DCPA, DCNA
♦ Emergency Off devices in compliance with EN 60204 IEC 204 (VDE 0113) must
remain functional in all operating modes of the control device. Resetting the
Emergency Off device must not result in uncontrolled or undefined re-starts.
♦ In those cases, where short circuits in the control device can result in
considerable material damage or even serious bodily harm (i.e. potentially
dangerous short circuits), external measures or devices must be taken or fitted
to ensure that operation is not dangerous even if a short circuit does occur (e.g.
independent limit switches, mechanical locks etc.).
♦ MICROMASTER inverters work with high voltages.
♦ Certain parameter settings can cause the inverter to start up again
automatically after the supply voltage has failed.
♦ The motor parameters must be configured exactly to ensure perfect motor
overload protection.
♦ The device provides an internal motor overload protection system in compliance
with UL508C, section 42. See P0610 and P0335, the pre-setting for i2t is ON.
Motor overload protection can also be secured via an external KTY84 or PTC.
♦ This equipment is suitable for use in a circuit capable of delivering not more
than 10,000 (Frame Size C) or 42,000 (Frame Sizes D to GX) symmetrical
amperes (rms), for a maximum voltage of 460 V when protected by an H, J or K
type fuse, a circuit breaker or self-protected combination motor controller (for
more details see Appendix F).
♦ This device must not be used as an „Emergency Off device“ (see EN 60204,
9.2.5.4).
MICROMASTER 430
62
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
4.1
4 MICROMASTER 430 functions
Frequency set point (P1000)
¾ Pre-setting:
¾ Additional settings:
4.2
terminal 3/4 (AIN+/ AIN -, 0…10 V equivates to
0…50/60 Hz)
see P1000
Command sources (P0700)
ATTENTION
The ramp-up /ramp-down times and ramp smoothing also have an effect on the
motor’s start and stop behaviour. Further details about these functions are to be
found in the parameter list for parameters P1120, P1121, P1130 – P1134.
Start motor
¾ Default:
¾ Additional settings:
terminal 5 (DIN1, high)
see P0700 to P0708
Stop motor
¾ There are a number of possibilities to stop the motor:
¾ Default :
♦
OFF1
terminal 5 (DIN1, low)
♦
OFF2
OFF key on BOP-2, press the OFF key once for 2
seconds or press twice
♦ OFF3
¾ Additional settings:
not active in factory settings
see P0700 to P0708
Reversing the direction of rotation of the motor
This function is inhibited in the factory settings. To release it, you must set
P1110 = 0.
¾ Default:
terminal 6 (DIN2, high)
¾ Additional settings:
see P0700 to P0708
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
63
4 MICROMASTER 430 functions
4.3
OFF and brake function
4.3.1
OFF1
Issue 10/06
This command (which is triggered by the cancellation of the ON order) causes the
inverter to come to a standstill within the selected ramp-down time.
For parameters to change ramp-down time: see P1121
ATTENTION
¾ The ON and the subsequent OFF command must come from the same source.
¾ If the ON / OFF1 command is set for more than one digital input, only the
digital input set last will be valid, e.g. DIN3 is active.
¾ OFF1 can be combined with DC braking or compound braking.
4.3.2
OFF2
This command causes the motor to run down freely to a standstill (impulses
deactivated).
ATTENTION
The OFF command can have one or more sources. The default causes the OFF2
command to be set to BOP-2. This source continues to exist even if other sources
are defined by one of the parameters P0700 to P0708.
4.3.3
OFF3
The OFF3 command causes the motor to be slowed down quickly.
The binary input must be closed to start the motor if the command OFF3 has been
set. If OFF3 is closed, the motor can be started and stopped by commands OFF1
or OFF2.
If OFF3 is open, the motor cannot be started..
¾ ramp-down time: see P1135
ATTENTION:
OFF3 can be combined with DC braking, compound braking or dynamic braking.
4.3.4
DC braking
DC braking is possible together with OFF1 and OFF3. Direct current is input which
brakes the motor quickly and holds the shaft until the end of the braking period.
¾ Activate DC braking:
see P0701 to P0708
¾ Set DC brake period:
see P1233
¾ Set DC braking current:
see P1232
¾ Set DC braking start frequency:
see P1234
ATTENTION
If no digital input is set to DC braking, DC braking is active for P1233 ≠ 0 after
every OFF1 command with the period set in P1233.
MICROMASTER 430
64
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
4.3.5
4 MICROMASTER 430 functions
Compound braking
Compound braking is possible with OFF1 and OFF3. In the case of compound
braking, a DC component is superimposed on the alternating current.
Set braking current :
see P1236
4.4
Control modes (P1300)
MICROMASTER 430 has a number of different control modes based on U/fcontrol. The individual modes have been listed below, additional settings are listed
in the parameter list and the function plans contained therein.
¾ Linear U/f control
P1300 = 0
Can be used for variable and constant torque applications e.g. transport
systems and positive displacement pumps.
¾ Linear U/f control with flux current control (FCC)
P1300 = 1
This type of control can be used to improve the performance and dynamic
behaviour of the motor.
¾ Parabolic U/f control
P1300 = 2
This type of control can be used for variable torque loads e.g. fan and pumps.
¾ Multiple point U/f control
P1300 = 3
Please refer to the MICROMASTER 430 parameter list for more information on
this operating mode.
¾ U/f control for textile applications
P1300 = 5
There is no slip compensation gain or resonance dampening. The Imax
controller refers to voltage instead of frequency.
¾ U/f control with FCC for textile applications
A combination of P1300 = 1 and P1300 = 5.
P1300 = 6
¾ U/f control with independent voltage set point
P1300 = 19
Using the P1330, the voltage set point can be given independently from the
starting frequency of the ramp function generator (HLG).
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
65
4 MICROMASTER 430 functions
Issue 10/06
4.5
MICROMASTER 430 operating modes
4.5.1
Bypass Mode
Setting up an inverter bypass circuit
Figure 4-1 Bypass circuit
Function
Control of two interlocked contactors via relay outputs of MICROMASTER 430.
This circuit makes it possible to operate the motor via the inverter or directly via the
mains. The inverter is responsible for switching.
Switching is possible by the following means:
¾ error message from the inverter
¾ digital input
¾ inverter frequency
For further settings please refer to parameters list P1260 and following.
MICROMASTER 430
66
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
4.5.2
4 MICROMASTER 430 functions
Belt Failure Detection
Recognizes mechanical faults in drive section e.g. torn V-belt, pumps which have
run dry etc.
P1082
Max. frequency
Torque[Nm]
P2189
Upper torque threshold 3
P2190
Lower torque threshold 3
P2187
Upper torque threshold 2
P2188
Lower torque threshold 2
P2185
Upper torque threshold 1
P2186
Lower torque threshold 1
P2182
Threshold frequency 1
P2183
Threshold frequency 2
Frequency
[Hz]
P2184
Threshold frequency 3
Figure 4-2 Belt Failure Detection
Function
A torque band is monitored. This enables underload and overload conditions to be
recognized (e.g. ventilator not running correctly)
Comparison between current speed / torque curve with programmed envelope
curve. The upper and lower frequency curve can be specified via three supporting
points each. In addition a dead time until the function is triggered can be defined.
This avoids accidental triggering due to transient events.
For additional settings please refer to parameter list P2181 and following.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
67
4 MICROMASTER 430 functions
4.5.3
Issue 10/06
Motor Staging
Controlling additional drives via output relay
Mains
Mains
Pressure Sensor
Sensor
Pressure
Inverter
Inverter
Motor Starters
Motor
Starters
To Inverter PID Input
To Inverter PID Input
MV
M1
MV - Variable speed motor
M1 - Motor switched with relay 1
Figure 4-3
M2
M3
M2 - Motor switched with relay 2
M3 - Motor switched with relay 3
Motor Staging
Function
Enables up to three additional motors to be controlled based on PID control
The entire system is made up of a pump which is controlled by the inverter with up
to an additional 3 pumps which can be added to the system via contactors or motor
starters.The motor starter is controlled via the output relay in the inverter. Figure
4-3 shows a typical pump system.
This function can also be used accordingly for ventilators and ventilation shafts.
For additional settings please refer to parameter list P2370 and following.
MICROMASTER 430
68
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
4.5.4
4 MICROMASTER 430 functions
Energy Saving Mode
Energy saving mode to switch off the motor when it is in idle mode
Pressure
equalizing
reservoir
Energy
saving
mode
PID
RFG
PID
setpoint
?
PID
feedback
Pressure
sensor
Motor
control
PID
limit
PID
f
P2273
(?PID)
Motor
f(t)
Load
PID feedback
(Sensor)
%
PID setpoint
P2392
t
f
f*
?PID
PID setpoint
f Motor
f Restart
P2390 [Hz]
P1080
P2391
PID active
fRestart = P2000 ⋅
P2390 + 5%
100 %
P2390 [Hz] = P2000 ⋅
Figure 4-4
P2390
100 %
tx
t
ty
Energy saving mode active
PID active
P1080
⋅ P1121
P1082
fRestart
⋅ P1120
ty =
P1082
tx =
Energy Saving Mode
Function
Energy saving mode extends the function of the PID controller.
This enables the motor to be operated for a defined period of time with a minimum
frequency and to switch it off afterwards. If the re-start frequency is reached, the
motor is automatically re-started again. Energy saving mode is independent of the
Motor Staging Function. It is possible to combine Motor Staging and Energy Saving
Mode. For additional settings please refer to the parameter list P2390 and
following.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
69
4 MICROMASTER 430 functions
4.6
Issue 10/06
Free Function Blocks (P2800 ff)
Using free function blocks, internal signals (Digital inputs, set points, actual
values, ...) can be interlinked, to enable application specific control.
4.7
Faults and Alarms
SDP
With the SDP Faults and Alarms conditions are displayed via the two LEDs on the
SDP. For further information see Section 6.1 on page 76.
The operation status of the inverter is indicated by the two LEDs as follows:
¾ Green and yellow = Ready to run
¾ Green only
= Inverter running
BOP-2
If a BOP-2 has been fitted to the inverter, details of any fault condition will be
displayed by the operator panel. For detailed information of fault conditions and
alarms, See Section 6 parameter list.
MICROMASTER 430
70
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
5
5 System parameters
System parameters
This Chapter contains:
¾ An overview of the parameter structure of the MICROMASTER 430
¾ A parameter list in short form
5.1
Introduction to MICROMASTER system parameters ............................................. 72
5.2
Parameter overview ................................................................................................ 73
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
71
5 System parameters
5.1
Issue 10/06
Introduction to MICROMASTER system parameters
The parameters can only be changed by using the BOP-2 or the Serial
Interface.
Parameters can be changed and set using the BOP-2 to adjust the desired
properties of the inverter, such as ramp times, minimum and maximum frequencies
etc. The parameter numbers selected and the setting of the parameter values are
indicated on the optional five-digit LCD display.
¾ rxxxx indicates a display parameter, Pxxxx a setting parameter.
¾ P0010 initiates “quick commissioning”.
¾ The inverter will not run unless P0010 is set to 0 after it has been accessed.
This function is automatically perform if P3900 > 0.
¾ P0004 acts as a filter, allowing access to parameters according to their
functionality.
¾ If an attempt is made to change a parameter that cannot be changed in this
status, for example, cannot be changed whilst running or can only be changed
in quick commissioning, then
will be displayed.
¾ Busy Message
In some cases - when changing parameter values - the display on the BOP-2
for maximum of five seconds. This means the inverter is busy
shows
with tasks of higher priority.
ATTENTION
MICROMASTER 430 can only be operated using a BOP-2. If the BOP or AOP is
used, the following is displayed
.
5.1.1
Access Levels
There are three access levels available to the user; Standard, Extended and
Expert. The level of access is set by parameter P0003. For most applications,
Standard (P0003 = 1) or Extended parameters (P0003 = 2) are sufficient.
CAUTION
Some of level 4 parameters are for internal system settings only and should not be
modified.
Level 4 parameters should only be modified by authorized personnel.
The number of parameters that appear within each functional group depends on
the access level set in parameter P0003. For further details regarding parameters,
see the Parameter List on the Documentation CD-ROM.
MICROMASTER 430
72
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
5.2
5 System parameters
Parameter overview
P0004 = 2
Inverter Unit
P0004 = 2, P0003 = 1
Parameters level 1
concerning the inverter unit
P0004 = 2, P0003 = 2
Parameters level 1 and 2
concerning the inverter unit
P0004 = 0
P0004 = 2, P0003 = 3,
Parameters level 1, 2 and 3
concerning the inverter unit
(no filter function)
allows direct access
to the parameters.
For BOP-2
depending on the
selected access level
P0004 = 2, P0003 = 4
Parameters level 1, 2, 3 and 4
concerning the inverter unit
3 = 4,
el Ser
P 0 0 03 =
3
=
P0004 = 4
Speed sensor
e
Exp rt
A
c c e ss L
ev
P0003
ces s Le
v
rd
c
,A
l
da
P0 0
ve
c
an
A
2,
el
Communication
=3
ess Leve P0004
Motor Data
c
c
A
lS
1,
t
=
ce s s L e
ed
end
xt
P0004 = 20
Inverter Unit
E
03
Alarms, Warnings &
Monitoring
P0004 = 2
PI Controller
00
P0004 = 21
P0004 = 22
c e P0
vi
P0004 = 13
P0004 = 5
Motor Control
Technology
Application / units
P0004 = 12
P0004 = 7
Drive Features
Commands and
Digital I/O
P0004 = 10
P0004 = 8
Setpoint Channel &
Ramp Generator
Analogue I/O
Figure 5-1 Parameter Overview
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
73
5 System parameters
Issue 10/06
MICROMASTER 430
74
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
6
Troubleshooting
Troubleshooting
This Chapter contains:
¾ An overview of the operating statuses of the inverter with the SDP
¾ Notes on troubleshooting with the BOP-2
¾ A list of the alarms and fault messages
6.1
Troubleshooting with the SDP ................................................................................ 76
6.2
Troubleshooting with the BOP-2............................................................................. 77
6.3
Fault messages....................................................................................................... 78
6.4
Alarm Messages ..................................................................................................... 78
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
75
Troubleshooting
Issue 10/06
WARNING
Repairs on equipment may only be carried out by Siemens Service, by repair
centers authorized by Siemens or by qualified personnel who are thoroughly
acquainted with all the warnings and operating procedures contained in this
manual.
Any defective parts or components must be replaced using parts contained in the
relevant spare parts list.
Disconnect the power supply before opening the equipment for access.
6.1
Troubleshooting with the SDP
Table 6-1 explains the
meaning of the various
states of the LEDs on
the SDP.
Table 6-1
LEDs for indicating the drive
state
Off
On
approx. 0,3 s, flashing
approx. 1 s, twinkling
Inverter
conditions indicated by the LEDs on the SDP
Mains not present
Fault inverter temperature
Ready to run
Warning current limit - both
LEDs twinkling same time
Inverter fault - other than the
ones listed below
Other warnings - both LEDs
twinkling alternatively
Inverter running
Undervoltage trip /
undervoltage warning
Fault overcurrent
Drive is not in ready state
Fault overvoltage
ROM failure - Both LEDs
flashing same time
Fault motor overtemperature
RAM failure - Both LEDs
flashing alternatively
MICROMASTER 430
76
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
6.2
Troubleshooting
Troubleshooting with the BOP-2
Warnings and faults are displayed on the BOP-2 with Axxx and Fxxx respectively.
The individual messages are shown in Section 6.3.
If the motor fails to start when the ON command has been given:
¾ Check that P0010 = 0.
¾ Check that a valid ON signal is present.
¾ Check that P0700 = 2 (for digital input control) or
P0700 = 1 (for BOP-2 control).
¾ Check that the setpoint is present (0 to 10V on Terminal 3) or the setpoint has
been entered into the correct parameter, depending upon the setpoint source
(P1000). See the Parameter List for further details.
If the motor fails to run after changing the parameters, set P0010 = 30 then P0970
= 1 and press P to reset the inverter to the factory default parameter values.
Now use a switch between terminals 5 and 9 on the control board. The drive
should now run to the defined setpoint by analogue input.
NOTICE
Motor data must relate to the inverter data power range and voltage.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
77
Troubleshooting
6.3
Issue 10/06
Fault messages
In the event of a failure, the inverter switches off and a fault code appears on the
display.
NOTE
To reset the fault code, one of three methods listed below can be used:
1. Cycle the power to the drive.
button on the BOP-2.
2. Press the
3. Via Digital Input 3 (default setting)
Fault messages are stored in parameter r0947 under their code number (e.g.
F0003 = 3). The associated error value is found in parameter r0949. The value 0 is
entered if a fault has no error value. It is furthermore possible to read out the point
in time that a fault occurred (r0948) and the number of fault messages (P0952)
stored in Parameter r0947.
A detailed description of the fault messages is provided in the parameter list.
6.4
Alarm Messages
Alarm messages are stored in parameter r2110 under their code number (e.g.
A0503 = 503) and can be read out from there.
A detailed description of the alarm messages is provided in the parameter list.
MICROMASTER 430
78
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
7
MICROMASTER 430 specifications
MICROMASTER 430 specifications
This Chapter contains:
¾ Table 7.1
¾ Table 7-2
¾ Table 7-3
¾ Table 7-4
contains the general technical specifications for the
MICROMASTER 430 inverter
contains terminal tightening torques and the required cooling air
flow
containes current values depending on pulse frequency
includes various tables of specific technical data for individual
MICROMASTER 430 inverters
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
79
MICROMASTER 430 specifications
Table 7-1
Issue 10/06
MICROMASTER 430 Performance Ratings
Feature
Mains Operating Voltage
& Power Ranges
Specification
VT
3 AC 380 to 480 V ± 10 %
Input Frequency
47 to 63 Hz
Output frequency
0 Hz to 650 Hz
Power Factor
≥ 0.7
Inverter Efficiency
Frame Sizes C to F:
Frame Sizes FX and GX:
7.50 kW – 90.0 kW
(10.0 hp – 120 hp)
96 % to 97 %
97 % to 98 %
Frame Sizes C to F:
Overload Capability for
variable torque (VT)
1.1 x Nominal output current
(i.e. 110 % overload) for 60 s every 300 s and
1.4 x Nominal output current
(i.e 140 % overload) for 3 s every 300 s
Frame Sizes FX and GX: 1.1 x Nominal output current
(i.e. 110% overload) for 59 s every 300 s and
1.5 x Nominal output current
(i.e 150% overload) for 1 s every 300s
Inrush Current
Less than rated input current
Power-ON-OFF cycle time
Frame Sizes C to E:
every 30 s
Frame Size F:
every 150 s
Frame Sizes FX and GX: every 300 s
Control Method
Linear V/f control, Linear V/f control with FCC, Parabolic V/f control, Multi-point
V/f control, V/f control for textile applications, V/f control with FCC for textile
applications, V/f control with independent voltage setpoint
Pulse Frequency
Frame Sizes C to F:
2 kHz to 8 kHz (2 kHz steps)
Frame Sizes FX and GX:
2 kHz to 8 kHz (2 kHz steps)
(Standard 2 kHz (VT),
power reduction see Table 7-3)
Fixed Frequencies
15, programmable
Skip Frequencies
4, programmable
Setpoint Resolution
0.01 Hz Digital, 0.01 Hz Serial, 10 bit Analogue
(motor potentiometer 0.1 Hz [0.1% (in PID mode)])
Digital Inputs
6, programmable (isolated), switchable active high / active low (PNP/NPN)
Analog Input 1
0 - 10 V, 0 - 20 mA and –10 V to +10 V
Analog Input 2
0 - 10 V and 0 - 20 mA
Relay Outputs
3, programmable 30 V DC / 5 A (resistive), 250 V AC 2 A (inductive)
Analogue Output
2, programmable (0 to 20 mA)
Serial Interface
RS-485, optional RS-232
Electromagnetic Compatibility
Frame Sizes C to F:
Optional EMC filters to EN 55011 Class A or B,
also Internal Class A filters available
Frame Sizes FX and GX: With EMI filter (available as an option) the limiting
values of the EN 55011, Class A are fulfilled for
conducted emission (line commutating choke
required).
Braking
DC braking, Compound braking
Protection Level
IP20
Temperature range (VT)
Frame Sizes C to F:
-10 °C to +40 °C (14 °F to 104 °F)
Frame Sizes FX and GX: 0 °C to +40 °C (32 °F to 104 °F), to 55 °C (131 °F)
Power reduction see Figure 2-2
Storage Temperature
-40 °C to +70 °C (40 °F to 158 °F)
MICROMASTER 430
80
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
MICROMASTER 430 specifications
Humidity
< 95 % RH – non-condensing
Operational Altitudes
Frame Sizes C to F:
Up to 1000 m above sea level without derating
Frame Sizes FX and GX: Up to 2000 m above sea level without derating
Protection Features
Undervoltage , Overvoltage, Overload, Ground Faults, Short circuit, Stall
Prevention, Motor Blocking Protection, Motor Overtemperature, Inverter
Overtemperature, Parameter Interlock
Frame Sizes C to F:
Frame Sizes FX and GX:
CE Marked
Table 7-2
Conformity with EC Low Voltage Directive 73/23/EEC
and Electromagnetic Compatibility Directive 89/336/EEC
Dimensions, required cooling air flow and tightening torques for power terminals
Frame
Size
Dimensions
C
BxHxT
D
BxHxT
E
F
FX
GX
UL, cUL, CE, C-tick
UL (in preparation), cUL (in preparation), CE
BxHxT
mm
inch
7,28 × 9,65 × 7,68
mm
275 × 520 × 245
inch
10,82 × 20,47 × 9,65
mm
275 × 650 × 245
BxHxT
Tightening torques for
power terminals
l/s
54,9
Nm
2,25
CFM
116,3
lbf-ft
1,7
2 × 54,9
Nm
CFM
2 × 116,3
lbf-ft
l/s
2 × 54,9
Nm
l/s
10 (max.)
7,4 (max.)
10 (max.)
inch
10,82 × 25,59 × 9,65
CFM
2 × 116,3
lbf-ft
mm
350 × 850 mm × 320
Hight with filter 1150
l/s
150
Nm
50
inch
13,78 × 33,46 × 12,60
Hight with filter 45,28
CFM
317,79
lbf-ft
36,9
mm
326 × 1400 × 356
225
Nm
25
BxHxT
BxHxT
185 × 245 × 195
Required cooling air flow
inch
12,80 × 55,12 × 12,83
mm
326 × 1533 × 545
inch
12,80 × 60,35 × 21,46
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
l/s
CFM
7,4 (max.)
478,13
lbf-ft
18,4
l/s
440
Nm
25
CFM
935
lbf-ft
18,4
81
MICROMASTER 430 specifications
Table 7-3
Issue 10/06
Current reduction depending on pulse frequency
Output current in A with a switching frequency of;
Mains
voltage
Power
[kW]
2 kHz
4 kHz
6 kHz
8 kHz
10 kHz
12 kHz
14 kHz
3 AC 400 V
7,5
19,0
19,0
17,1
15,2
13,3
11,4
9,5
7,6
11,0
26,0
26,0
24,7
23,4
20,8
18,2
15,6
13,0
15,0
32,0
32,0
28,8
25,6
22,4
19,2
16,0
12,8
18,5
38,0
38,0
36,1
34,2
30,4
26,6
22,8
19,0
22
45,0
45,0
40,5
36,0
31,5
27,0
22,5
18,0
30
62,0
62,0
55,8
49,6
43,4
37,2
31,0
24,8
37
75,0
75,0
71,3
67,5
60,0
52,5
45,0
37,5
45
90,0
90,0
81,0
72,0
63,0
54,0
45,0
36,0
55
110,0
110,0
93,5
77,0
63,3
49,5
41,3
33,0
75
145,0
145,0
123,3
101,5
83,4
65,3
54,4
43,5
97,9
84,6
71,2
62,3
53,4
90
178,0
178,0
138,0
110
205,0
180,4
–
–
–
–
–
–
132
250,0
220,0
–
–
–
–
–
–
160
302,0
265,8
–
–
–
–
–
–
200
370.0
325,6
–
–
–
–
–
–
250
477,0
419,8
–
–
–
–
–
–
MICROMASTER 430
82
16 kHz
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
MICROMASTER 430 specifications
Table 7-4
MICROMASTER 430 Specifications
In order to have a UL compliant installation fuses from the SITOR range with
the appropriate current rating must be used.
Input voltage range
(with built in Class A Filter)
Order No.
6SE6430-
3 AC 380 V … 480 V, ± 10 %
2AD275CA0
7,5
10,0
2AD311CA0
11,0
15,0
2AD315CA0
15,0
20,0
2AD318DA0
18,5
25,0
2AD322DA0
22,0
30,0
2AD330DA0
30,0
40,0
Output Power
[kW]
[hp]
[kVA]
10,1
14,0
19,8
24,4
29,0
34,3
VT Input Current 1)
[A]
17,3
23,1
33,8
37,0
43,0
59
VT Output Cur. Max.
[A]
19,0
26,0
32,0
38,0
45,0
Recommended Fuse
[A]
3NA
20
3807
32
3812
35
3814
50
3820
63
3822
Fuses recomnended for
UL applications
[A]
3NE
50
1817-0
63
1818-0
80
1820-0
VT Motor Output Rating
*
*
*
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2,5
14
10,0
8
2,5
14
10,0
8
4,0
12
10,0
8
4,0
12
10,0
8
C
6,0
10
10,0
8
6,0
10
10,0
8
10,0
8
35,0
2
10,0
8
35,0
2
10,0
8
35,0
2
10,0
8
35,0
2
D
16,0
6
35,0
2
16,0
6
35,0
2
[kg]
[lbs]
5,7
12,5
5,7
12,5
5,7
12,5
17,0
37,0
17,0
37,0
17,0
37,0
2AD337EA0
37,0
50,0
2AD345EA0
45,0
60,0
2AD355FA0
55,0
75,0
2AD375FA0
75,0
100,0
2AD388FA0
90,0
120,0
83,8
110,5
2
Input Cable Min.
Input Cable Max.
Output Cable Min.
Output Cable Max.
Frame Size
Weight
Order No.
6SE6430-
Output Power
[kW]
[hp]
[kVA]
VT Input Current 1)
[A]
VT Output Cur. Max.
[A]
Recommended Fuse
[A]
3NA
100
3830
Fuses recomnended for
UL applications
[A]
3NE
100
125
1021-0 1022-0
VT Motor Output Rating
Input Cable Max.
Output Cable Min.
Output Cable Max.
47,3
57,2
72
87
75,0
2
Input Cable Min.
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
25,0
3
35,0
2
25,0
3
35,0
2
[kg]
[lbs]
22,0
48,0
1) Secondary conditions:
*
90,0
125
3832
68,6
104
110,0
160
3836
139
169
145,0
178,0
160
3140
200
3144
160
1224-0
200
1225-0
200
1227-0
25,0
3
35,0
2
25,0
3
35,0
2
35,0
2
150,0
300
50,0
1/0
150,0
300
70,0
2/0
150,0
300
70,0
2/0
150,0
300
F
70,0
2/0
150,0
300
95,0
4/0
150,0
300
22,0
48,0
75,0
165,0
75,0
165,0
75,0
165,0
E
Frame Size
Weight
62,0
80
3824
Input current at the rated operating point - applies for the short-circuit
voltage of the line supply Vk = 2 % referred to the rated drive converter
power and a rated line supply voltage of 400 V without line commutating
reactor.
UL listed fuses such as Class NON from Bussmann are required for use in America
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
83
MICROMASTER 430 specifications
Issue 10/06
Input voltage range
(Unfiltered)
Order No.
3 AC 380 V … 480 V, ± 10 %
6SE6430-
2UD275CA0
2UD311CA0
2UD315CA0
2UD318DA0
2UD322DA0
7,5
10,0
11,0
15,0
15,0
20,0
18,5
25,0
22,0
30,0
2UD330DA0
Output Power
[kW]
[hp]
[kVA]
10,1
14,0
19,8
24,4
29,0
34,3
VT Input Current 1)
[A]
17,3
23,1
33,8
37,0
43,0
59
VT Output Cur. Max.
[A]
19,0
26,0
32,0
38,0
45,0
Recommended Fuse
[A]
3NA
20
3807
32
3812
35
3814
50
3820
63
3822
Fuses recomnended for
UL applications
[A]
3NE
VT Motor Output Rating
Input Cable Max.
Output Cable Min.
Output Cable Max.
Order No.
*
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2,5
14
10,0
8
2,5
14
10,0
8
4,0
12
10,0
8
4,0
12
10,0
8
C
6,0
10
10,0
8
6,0
10
10,0
8
10,0
8
35,0
2
10,0
8
35,0
2
10,0
8
35,0
2
10,0
8
35,0
2
D
16,0
6
35,0
2
16,0
6
35,0
2
[kg]
[lbs]
5,5
12,1
5,5
12,1
5,5
12,1
16,0
35,0
16,0
35,0
16,0
35,0
2UD337EA0
2UD345EA0
2UD355FA0
2UD375FA0
2UD388FA0
55,0
75,0
75,0
100,0
90,0
120,0
83,8
110,5
6SE6430-
37,0
50,0
45,0
60,0
Output Power
[kW]
[hp]
[kVA]
47,3
57,2
VT Input Current 1)
[A]
72
87
VT Motor Output Rating
VT Output Cur. Max.
[A]
Recommended Fuse
[A]
3NA
100
3830
Fuses recomnended for
UL applications
[A]
3NE
100
1021-0
75,0
2
Input Cable Min.
Input Cable Max.
Output Cable Min.
Output Cable Max.
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
2
[mm ]
[AWG]
25,0
3
35,0
2
25,0
3
35,0
2
[kg]
[lbs]
20,0
44,0
68,6
104
90,0
110,0
139
169
145,0
178,0
125
3832
160
3836
160
3140
200
3144
125
1022-0
160
1224-0
200
1225-0
200
1227-0
25,0
3
35,0
2
25,0
3
35,0
2
35,0
2
150,0
300
35,0
2
150,0
300
70,0
2/0
150,0
300
70,0
2/0
150,0
300
F
70,0
2/0
150,0
300
95,0
4/0
150,0
300
20,0
44,0
56,0
123,0
56,0
123,0
56,0
123,0
E
Frame Size
Weight
63
80
1818-0 1820-0
*
Frame Size
Weight
62,0
80
3824
*
2
Input Cable Min.
50
1817-0
30,0
40,0
1) Secondary conditions: Input current at the rated operating point - applies for the short-circuit voltage of the line
supply Vk = 2 % referred to the rated drive converter power and a rated line supply voltage
of 400 V without line commutating reactor.
*
UL listed fuses such as Class NON from Bussmann are required for use in America
MICROMASTER 430
84
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
MICROMASTER 430 specifications
Input voltage range
(Unfiltered)
Order No.
3 AC 380 V … 480 V, ± 10 %
6SE6430- 2UD41-1FA0
2UD41-3FA0 2UD41-6GA0 2UD42-0GA0 2UD42-5GA0
VT Motor Output Rating
[kW]
[hp]
110
150
132
200
160
250
200
300
250
333
Output Power
[kVA]
145,4
180
214,8
263,2
339,4
VT Input Current 1)
[A]
200
245
297
354
442
VT Output Cur. Max.
[A]
205
250
302
370
477
[A]
250
3NE1227-0
1 x 95 or
2 x 35
1 x 4/0 or
2x2
1 x 185 or
2 x 120
1 x 350 or
2 x 4/0
1 x 95 or
2 x 35
1 x 4/0 or
2x2
1 x 185 or
2 x 120
1 x 350 or
2 x 4/0
315
3NE1230-0
1 x 150 or
2 x 50
1 x 300 or
2 x 1/0
1 x 185 or
2 x 120
1 x 350 or
2 x 4/0
1 x 150 or
2 x 50
1 x 300 or
2 x 1/0
1 x 185 or
2 x 120
1 x 350 or
2 x 4/0
400
3NE1332-0
1 x 185 or
2 x 70
1 x 400 or
2 x 2/0
450
3NE1333-0
1 x 240 or
2 x 70
1 x 500 or
2 x 2/0
560
3NE1435-0
[mm]
10
[kg]
[lbs]
110
242
Recommended Fuse
2
[mm ]
Input Cable Min.
[AWG]
or [kcmil]
2
[mm ]
Input Cable Max.
[AWG]
or [kcmil]
2
[mm ]
Output Cable Min.
[AWG]
or [kcmil]
2
[mm ]
Output Cable Max.
Pipe cable shoe to
DIN 46235
[AWG]
or [kcmil]
Frame Size
Weight
2 x 95
2 x 4/0
2 x 240
2 x 240
2 x 240
2 x 400
2 x 400
2 x 400
1 x 185 or
2 x 70
1 x 400 or
2 x 2/0
1 x 240 or
2 x 70
1 x 500 or
2 x 2/0
2 x 240
2 x 240
2 x 240
2 x 400
2 x 400
2 x 400
10
10
10
10
116
256
170
375
174
384
FX
2 x 95
2 x 4/0
GX
176
388
1) Secondary conditions: Input current at the rated operating point - applies for the short-circuit voltage of the line
supply Vk ≥ 2.33 % referred to the rated drive converter power and a rated line supply
voltage of 400 V.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
85
MICROMASTER 430 specifications
Issue 10/06
MICROMASTER 430
86
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
8
8 Options
Options
An overview of the options available for the MICROMASTER 430 is given in this
section. For further information about options, please refer to the catalog or the
documentation CD.
8.1
Device-independent options
¾
¾
¾
¾
¾
8.2
Basic Operator Panel 2 (BOP-2)
PROFIBUS module
PC to inverter connection kit
BOP/AOP door mounting kit for single inverter control
“DriveMonitor” and "Starter" commissioning tool
Device-dependent options
Frame Sizes C to F
¾
¾
¾
¾
¾
¾
Gland plate (Frame size C)
EMC filter, Class A
EMC filter, Class B (Frame size C)
Line commutating choke
Output choke
LC Filter
CAUTION
If using output chokes or LC filters operation is only permissible with a pulse
frequency of 4 kHz. Make shure that the automatic pulse frequency reductions are
disabled.
Coercing required parameter adjusting: P1800 = 4 kHz , P0290 = 0 or 1.
Frame Sizes FX and GX
¾ Line commutating choke
¾ EMC filter, Class A (power commutating choke required)
¾ LC Filter
CAUTION
If using output chokes or LC filters operation is only permissible with a pulse
frequency of 4 kHz. Make shure that the automatic pulse frequency reductions are
disabled.
Coercing required parameter adjusting: P1800 = 4 kHz , P0290 = 0 or 1.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
87
8 Options
Issue 10/06
MICROMASTER 430
88
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
9
9 Electro-magnetic compatibility (EMC)
Electro-magnetic compatibility (EMC)
This Chapter contains:
EMC information.
9.1
Electro-magnetic compatibility ................................................................................ 90
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
89
9 Electro-magnetic compatibility (EMC)
9.1
Issue 10/06
Electro-magnetic compatibility
(EMC) All manufacturers / assemblers of electrical apparatus which “performs a
complete intrinsic function and is placed on the market as a single unit intended for
the end user” must comply with the EMC directive 89/336/EEC.
There are three routes for the manufacturer/assembler to demonstrate compliance:
9.1.1
Self-certification
This is a manufacturer's declaration that the European standards applicable to the
electrical environment for which the apparatus is intended have been met. Only
standards that have been officially published in the Official Journal of the European
Community can be cited in the manufacturer's declaration.
9.1.2
Technical construction file
A technical construction file can be prepared for the apparatus describing its EMC
characteristics. This file must be approved by a ‘Competent Body’ appointed by the
appropriate European government organization. This approach allows the use of
standards that are still in preparation.
9.1.3
EC type examination certificate
This approach is only applicable to radio communication transmitting apparatus. All
MICROMASTER 430 units are certified for compliance with the EMC directive,
when installed in accordance with the recommendations in Section 2.
9.1.4
EMC Directive Compliance with Imminent Harmonics
Regulations
Since 1st January 2001 all electrical apparatus covered by the EMC Directive will
have to comply with EN 61000-3-2 "Limits for harmonic current emissions
(equipment input ≤ 16 A per phase)".
All Siemens variable speed drives of the MICROMASTER, MIDIMASTER,
MICROMASTER Eco and COMBIMASTER ranges, which are classified as
"Professional Equipment" within the terms of the standard, fulfill the requirements
of the standard.
The allowed harmonic currents for “professional equipment” with an input power
> 1 kW are not yet defined. Therefore, any electrical apparatus containing the
above drives which has an input power > 1 kW will not require connection
approval.
MICROMASTER 430
90
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
9.1.5
9 Electro-magnetic compatibility (EMC)
Classification of EMC performance
Three General classes of EMC performance are available as detailed below:
Class 1: General Industrial
Compliance with European Standard EN 61800-3 (EMC Product Standard for
Power Drive Systems) for use in Second Environment (Industrial).
Table 9-1
General Industrial
EMC Phenomenon
Emissions:
Immunity:
Standard
Level
Radiated Emissions
EN 55011
Level A1
Leitungsgebundene
Emissionen
EN 61800-3
Limits complying with EN 55011,
Class A, Group 2
Electrostatic Discharge
EN 61000-4-2
8 kV air discharge
Burst Interference
EN 61000-4-4
2 kV power cables, 1 kV control
Radio Frequency
Electromagnetic Field
EN 61000-4-3
26-1000 MHz, 10 V/m
Class 2: Filtered Industrial
This level of performance will allow the manufacturer/assembler to self-certify their
apparatus for compliance with the EMC directive for the industrial environment as
regards the EMC performance characteristics of the power drive system.
Performance limits are as specified in the Generic Industrial Emissions and
Immunity standards EN 50081-2 and EN 50082-2.
Table 9-2
Filtered Industrial
EMC Phenomenon
Emissions:
Immunity:
Standard
Level
Radiated Emissions
EN 55011
Limit A1
Conducted Emissions
EN 61800-3
Limits complying with EN 55011,
Class A, Group 2
Supply Voltage Distortion
EN 61000-2-4
Voltage Fluctuations, Dips,
Unbalance, Frequency
Variations
EN 61000-2-1
Magnetic Fields
EN 61000-4-8
50 Hz, 30 A/m
Electrostatic Discharge
EN 61000-4-2
8 kV air discharge
Burst Interference
EN 61000-4-4
2 kV power cables, 2 kV control
Radio Frequency
Electromagnetic Field,
amplitude modulated
EN 61000-4-3
80-1000 MHz, 10 V/m, 80% AM,
power and signal lines
Radio-frequency
Electromagnetic Field,
pulse modulated
EN 61000-4-3
900 MHz, 10 V/m 50% duty cycle,
200 Hz repetition rate
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
91
9 Electro-magnetic compatibility (EMC)
Issue 10/06
Only Frame Size C
Class 3: Filtered - for residential, commercial and trade applications
This level of performance will allow the manufacturer / assembler to self-certify
compliance of their apparatus with the EMC directive for the residential,
commercial and trade applications environment as regards the EMC performance
characteristics of the power drive system. Performance limits are as specified in
the generic emission and immunity standards EN 61000-6-3 and EN 61000-6-1 in
residential.
Table 9-3
Filtered for Residential, Commercial and trade applications
EMC Phenomenon
Emissions:
Immunity:
*
Standard
Level
Radiated Emissions*
EN 55011
Limit B
Conducted Emissions
EN 61800-3
Category C1:
Limit complying with
EN 55011, Class B
Category C2:
Limit complying with
EN 55011, Class A
Supply Voltage Distortion
EN 61000-2-4
Voltage Fluctuations, Dips,
Unbalance, Frequency
Variations
EN 61000-2-1
Magnetic Fields
EN 61000-4-8
50 Hz, 30 A/m
Electrostatic Discharge
EN 61000-4-2
8 kV air discharge
Burst Interference
EN 61000-4-4
2 kV power cables, 2 kV control
Radio Frequency
Electromagnetic Field,
amplitude modulated
EN 61000-4-3
80-1000 MHz, 10 V/m, 80%
AM, power and signal lines
Radio-frequency
Electromagnetic Field,
pulse modulated
EN 61000-4-3
900 MHz, 10 V/m 50% duty
cycle, 200 Hz repetition rate
These limits are dependent on the inverter being correctly installed inside a
metallic switchgear enclosure. The limits will not be met if the inverter is not
enclosed.
Notes
¾ To achieve these performance levels, you must not exceed the default Pulse
frequency nor use cables longer than 25 m.
¾ The MICROMASTER inverters are intended exclusively for professional
applications. Therefore, they do not fall within the scope of the harmonics
emissions specification EN 61000-3-2.
¾ Maximum mains supply voltage when filters are fitted is 480 V.
MICROMASTER 430
92
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
9 Electro-magnetic compatibility (EMC)
Table 9-4
Compliance Table
Frame Sizes C to F
Class 1 – General Industrial
6SE6430-2U***-**A0
Units without filters, all voltages and performances. The product norm
EN 61800-3 +A11 for "Variable-speed electrical drives, Part 3: EMC
product standard including specific test methods” specifies limits for
conducted emissions which cannot be complied with by unfiltered
inverters in the second environment.
Filtered inverters (as described under Class 2) must be installed for
drive systems in C3 installations.
The use of unfiltered inverters in industrial environments is allowed only
if they are part of a system which is equipped with line filters on the
higher-level supply side.
Class 2 – Filtered Industrial
6SE6430-2A***-**A0
All units with integral Class A filters
Class 3 – Filtered for residential, commerical and trade applications
6SE6430-2A***-**A0 with
6SE6400-2FS0*-***0
Units with fitted Class A filters and additional external Class B filters.
6SE6430-2U***-**A0 with
EMV-Filter Class B
(e.g. Fa. Schaffner)
6SE6430-2A***-**A0
Unfiltered units fitted with external Class B filters
All units with fitted Class A filters.
For drive systems in category C2 installations, the following warning
notice is necessary:
In residential environments, this product may cause radio-frequency
disturbances which may necessitate interference suppression
measures.
* denotes any value is allowed.
Frame Sizes FX to GX
Class 1 – General Industrial
6SE6430-2U***-**A0
Units without filters, all voltages and performances. The product norm
EN 61800-3 +A11 for "Variable-speed electrical drives, Part 3: EMC
product standard including specific test methods” specifies limits for
conducted emissions which cannot be complied with by unfiltered
inverters in the second environment.
Filtered inverters (as described under Class 2) must be installed for
drive systems in C3 installations.
The use of unfiltered inverters in industrial environments is allowed only
if they are part of a system which is equipped with line filters on the
higher-level supply side.
Class 2 – Filtered Industrial
6SE6430-2U***-**A0 with
6SL3000-0BE**-***0
With external EMI filter (available as an option) the limiting values of the
EN 55011, Class A are fulfilled for conducted emission.
(line commutating choke required)
* denotes any value is allowed.
Category C3:
Drive system (PDS) with rated voltage < 1000 V.
For use in second environment.
Category C2:
Drive system (PDS) with rated voltage < 1000 V. For use in first
environment. Installation and commissioning by EMC expert only.
Category C1:
Drive system (PDS) with rated voltage < 1000 V.
For use in first environment.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
93
9 Electro-magnetic compatibility (EMC)
Issue 10/06
MICROMASTER 430
94
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Changing the Operator Panel
Appendices
A
Changing the Operator Panel
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
95
Removing Front Covers
Issue 10/06
B
Removing Front Covers
B.1
Removing Front Covers Frame Size C
MICROMASTER 430
96
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
B.2
Removing Front Covers
Removing Front Covers Frame Sizes D and E
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
97
Removing Front Covers
B.3
Issue 10/06
Removing Covers Frame Size F
MICROMASTER 430
98
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
B.4
Removing Front Covers
Removing Front Covers Frame Sizes FX and GX
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
99
Removing the I/O Board
C
Issue 10/06
Removing the I/O Board
NOTICE
1. Only a small amount of pressure is required to release the I/O Board catch.
2. the I/O Board is removed using the same technique regardless of frame size.
MICROMASTER 430
100
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Removing ‘Y’ Cap
D
Removing ‘Y’ Cap
D.1
Removing ‘Y’ Cap Frame Size C
!
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
101
Removing ‘Y’ Cap
D.2
Issue 10/06
Removing ‘Y’ Cap Frame Sizes D and E
MICROMASTER 430
102
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
D.3
Removing ‘Y’ Cap
Removing ‘Y’ Cap Frame Sizes F
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
103
Removing ‘Y’ Cap
D.4
Issue 10/06
Removing ‘Y’ Cap Frame Sizes FX
TORX T20
open
link
Bügel
lösen
MICROMASTER 430
104
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
D.5
Removing ‘Y’ Cap
Removing ‘Y’ Cap Frame Sizes GX
TORX T20
open link
Bügel lösen
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
105
Applicable Standards
E
Issue 10/06
Applicable Standards
European Low Voltage Directive
The MICROMASTER product range complies with the requirements of the Low
Voltage Directive 73/23/EEC as amended by Directive 98/68/EEC. The units are
certified for compliance with the following standards:
EN 61800-5-1 Adjustable speed electrical power drive systems,
Part 5-1: Safety requirements –
Electrical, thermal and energy
EN 60204-1
Safety of machinery - Electrical equipment of machines
European Machinery Directive
The MICROMASTER inverter series does not fall under the scope of the Machinery
Directive. However, the products have been fully evaluated for compliance with the
essential Health & Safety requirements of the directive when used in a typical
machine application. A Declaration of Incorporation is available on request.
European EMC Directive
When installed according to the recommendations described in this manual, the
MICROMASTER fulfils all requirements of the EMC Directive as defined by the
EMC Product Standard for Power Drive Systems EN 61800-3.
Underwriters Laboratories
UL and CUL LISTED POWER CONVERSION EQUIPMENT.
ISO 9001
Siemens plc operates a quality management system, which complies with the
requirements of ISO 9001.
MICROMASTER 430
106
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
F
Short circuit current rating (SCCR)
Short circuit current rating (SCCR)
Frame Size C
The equipment has a "standard SCCR" value of 10 kA, which complies with the
requirements of UL508C.
In addition to the "standard SCCR" a "high SCCR" is available which can be used
for industrial control panel installations in line with the National Electrical Code
(NEC) article 409 (edition 2005) and Underwriters Laboratories UL508A (effective
April 2006).
The uL certification of MICROMASTER 430 allows the drives to adopt a high
SCCR equal to the interupt current rating of the branch-circuit protection (BCP)
device protecting the drive.
Hence by selection of the correct uL listed BCP device with appropriate interrupt
rating for the application, any high SCCR rating can be achieved for
MICROMASTER 430, including SCCR values above 10 kA.
The above statements are valid for the respective maximum voltage of the drive
when protected by a UL recognised/listed H, J or K type fuse, a circuit breaker or
self-protected combination motor controller.
Frame Sizes D to GX
The equipment has a "standard SCCR" value of 42 kA, which complies with the
requirements of UL508C.
A "high SCCR", which can be used for industrial control panel installations in line
with the National Electrical Code (NEC) article 409 (edition 2005) and Underwriters
Laboratories UL508A (effective April 2006), can be achieved with the use of current
limiting fuses or circuit breakers with an appropriate interrupt rating and derived let
through current.
For compliance with NEC article 409 and UL508A the calculation, selection and
marking of the current limiting device must be carried out by an qualified engineer.
The above statements are valid for the respective maximum voltage of the drive
when protected by a UL recognised/listed H, J or K type fuse, a circuit breaker or
self-protected combination motor controller.
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
107
List of Abbreviations
G
Issue 10/06
List of Abbreviations
AC
AD
ADC
ADR
AFM
AIN
AOP
AOUT
ASP
ASVM
BCC
BCD
BI
BICO
BO
BOP
C
CB
CCW
CDS
CFM
CI
CM
CMD
CMM
CO
CO/BO
COM
COM-Link
CT
CT
CUT
CW
DA
DAC
DC
DDS
DIN
Alternating current
Analog digital converter
Analog digital converter
Address
Additional frequency modification
Analog input
Advanced operator panel
Analog output
Analog setpoint
Asymmetric space vector modulation
Block check character
Binary-coded decimal code
Binector input
Binector / connector
Binector output
Basic operator panel
Commissioning
Communication board
Counter-clockwise
Command data set
Cubic feet per minute (1 l/s ≅ 2,1 CFM)
Connector input
Configuration management
Commando
Combimaster
Connector output
Connector output / Binector output
Common (terminal that is connected to NO or NC)
Communication link
Commissioning, ready to run
Constant torque
Commissioning, run, ready to run
Clockwise
Digital analog converter
Digital analog converter
Direct current
Drive data set
Digital input
MICROMASTER 430
108
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
List of Abbreviations
DIP
DOUT
DS
EEC
EEPROM
ELCB
EMC
EMF
EMI
FAQ
FCC
FCL
FF
FFB
FOC
FSA
GSG
GUI ID
HIW
HSW
HTL
I/O
IBN
IGBT
IND
JOG
KIB
KTY
LCD
LED
LGE
MHB
MM4
MOP
NC
NO
NPN
OPI
PDS
PID
PKE
PKW
PLC
PLI
DIP switch
Digital output
Drive state
European Economic Community
Electrical erasable programmable read-only
Earth leakage circuit breaker
Electro-magnetic compatibility
Electromotive force
Electro-magnetic interference
Frequently asked questions
Flux current control
Fast current limit
Fixed freqeuncy
Free function block
Field orientated control
Frame size A
Getting started guide
Global unique identifier
Main actual value
Main setpoint
High-threshold logic
Input and output
Commissioning
Insulated gate bipolar transistor
Sub-index
Jog
Kinetic buffering
Liguid crystal display
Light emitting diode
Length
Motor holding brake
MICROMASTER 4th. Generation
Motor potentiometer
Normally closed
Normally open
Operating instructions
Power drive system
PID controller (proportional, integral, derivative)
Parameter ID
Parameter ID value
Programmable logic controller
Parameter list
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
109
List of Abbreviations
PNP
PPO
PTC
PWE
PWM
PX
PZD
QC
RAM
RCCB
RCD
RFG
RFI
RPM
SCL
SDP
SLVC
STW
STX
SVM
TTL
USS
VC
VT
ZSW
Issue 10/06
Parameter process data object
Positive temperature coefficient
Parameter value
Pulse-width modulation
Power extension
Process data
Quick commissioning
Random-access memory
Residual current circuit breaker
Residual current device
Ramp function generator
Radio-frequency interference
Revolutions per minute
Scaling
Status display panel
Sensorless vector control
Control word
Start of text
Space vector modulation
Transistor-transistor logic
Universal serial interface
Vector control
Variable torque
Status word
MICROMASTER 430
110
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Index
Index
A
Access Levels...........................................68
Adaptation of fan voltage..........................35
Altitude......................................................20
Ambient operating conditions
Altitude ..................................................20
Atmospheric Pollution ...........................21
Electromagnetic Radiation....................21
Humidity Range ....................................20
Installation und Kühlung .......................21
Shock ....................................................20
Vibration................................................20
Water hazard ........................................21
Ambient operating conditions ...................20
Applicable standards
European EMC Directive ....................102
European Low Voltage Directive ........102
European Machinery Directive............102
ISO 9001.............................................102
Underwriters Laboratories ..................102
Atmospheric pollution ...............................21
B
Basic operation
changing parameters with BOP-2.........49
external motor thermal overload
protection ........................................53, 55
general ..................................................54
with BOP-2............................................54
with SDP ...............................................45
Belt Failure Detection ...............................63
BOP-2
default settings with BOP-2 ..................47
operation with BOP-2............................47
Bypass Mode............................................62
C
Commissioning .........................................39
Compound braking ...................................60
connection drawing – frame size FX ........32
connection drawing – frame size GX........33
Connection Terminals ..............................31
Contact address .........................................5
Control modes ..........................................61
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
Current reduction depending on pulse
frequency.............................................. 77
D
DC braking ............................................... 60
Default settings ........................................ 47
Dimensions and Torques......................... 26
Drill pattern for MICROMASTER 440 ...... 23
E
Electrical Installation ................................ 28
Electro-Magnetic Compatibility
EC type-examination certificate ........... 86
general ........................................... 85, 86
self-certification .................................... 86
technical construction file ..................... 86
Electro-Magnetic Interference.................. 36
avoiding EMI......................................... 36
Electromagnetic radiation ........................ 21
EMC ......................................................... 86
EMC Directive Compliance...................... 86
EMC performance
filtered for residential, commercial and
light industry ......................................... 89
filtered industrial class .......................... 88
general industrial class......................... 87
EMI........................................................... 36
Energy Saving Mode................................ 65
F
Fan fuses ................................................. 35
Fault messages
with the BOP-2 fitted ............................ 73
with the SDP fitted................................ 72
Faults and Alarms
with BOP-2 ........................................... 66
with SDP............................................... 66
Features................................................... 15
flux current control (FCC ) ....................... 61
Foreword.................................................... 5
Free Function Blocks ............................... 66
Frequency set point ................................. 58
111
Index
Issue 10/06
H
P
Humidity Range ........................................20
Parabolic U/f control................................. 61
Parameter
Systemparameter ................................. 67
Parameters
changing parameters with BOP-2 ........ 49
Performance characteristics .................... 16
Performance Ratings ............................... 76
Power and motor connections ................. 30
single phase ......................................... 34
Protection characteristics......................... 16
I
Installation ................................................17
after a period of storage..................17, 19
Installation dimensions for MICROMASTER
440 Version FX .....................................24
Installation of options in the electronic box
..............................................................27
Installation und Kühlung ...........................21
Internet Home Address ..............................5
Inverter block diagram..............................41
L
Linear U/f control ......................................61
Long cables
operation with........................................29
M
Main characteristics..................................15
Mechanical Installation .............................22
MICROMASTER 430
general ..................................................14
main characteristics ..............................15
performance characteristics..................16
protection characteristics ......................16
specifications ........................................75
Motor connections ....................................30
Motor data ................................................53
Motor Staging ...........................................64
Multiple point U/f control...........................61
O
Operation
OFF and brake function ........................59
Operation with
long cables............................................29
Residual Current Device.......................29
ungrounded IT supplies ........................29
Operator panels
BOP-2 ...................................................47
changing the operator panel .................91
SDP.......................................................44
Options
Device-dependent options ....................83
Device-independent options .................83
Options for electronic box.........................27
Overview...................................................13
Q
Qualified personnel .................................... 6
Quick commissioning ............................... 50
R
Removing ‘Y’ Cap Frame Sizes C ........... 97
Removing ‘Y’ Cap Frame Sizes D and E. 98
Removing ‘Y’ Cap Frame Sizes F............ 99
Removing Covers Frame Size C ............. 92
Removing Covers Frame Size F.............. 94
Removing Covers Frame Sizes D and E .....
........................................................ 93, 95
Removing the I/O Board .......................... 96
Reset to Factory default........................... 53
Residual Current Device
operation with ....................................... 29
S
Safety instructions...................................... 7
Screening Methods .................................. 37
SDP
Default settings..................................... 44
operation with SDP............................... 44
Shock ....................................................... 20
Specifications........................................... 78
T
Technical Support ...................................... 5
Terminal Torques..................................... 77
Troubleshooting ....................................... 71
U
Ungrounded (IT) supplies
operation with ....................................... 29
MICROMASTER 430
112
Operating Instructions
6SE6400-5AE00-0BP0
Issue 10/06
Index
W
Warnings, cautions & notes
commissioning ........................................8
definitions................................................6
dismantling & disposal ............................9
general ....................................................7
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
operation ................................................ 9
repair ...................................................... 9
transport & storage................................. 8
Water hazard ........................................... 21
Wiring Guidelines EMI ............................. 37
113
Index
Issue 10/06
MICROMASTER 430
114
Operating Instructions
6SE6400-5AE00-0BP0
Suggestions and/or Corrections
To:
Siemens AG
Automation & Drives Group
SD SPA PM 4
P.O. Box 3269
D-91050 Erlangen
Federal Republic of Germany
Suggestions
Corrections
For Publication/Manual:
MICROMASTER 430
Email: documentation.sd@siemens.com
User Documentation
From
Name:
Operating Instructions
Order Number:
6SE6400-5AE00-0BP0
Date of Issue: 10/06
Company/Service Department
Address:
Should you come across any printing
errors when reading this publication,
please notify us on this sheet.
Suggestions for improvement are also
welcome.
Telephone: __________ /
Telefax: ________ /
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
115
MICROMASTER 430
116
Operating Instructions
6SE6400-5AE00-0BP0
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
117
Siemens AG
Bereich Automation and Drives (A&D)
Geschäftsgebiet Standard Drives (SD)
Postfach 3269, D-91050 Erlangen
Federal Republic of Germany
Siemens Aktiengesellschaft
© Siemens AG, 2002, 2005, 2006
Subject to change without prior notice
Order No.: 6SE6400-5AE00-0BP0
Date: 10/06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising