356017 - F150 - Expedition - 99 - Radio Install

356017 - F150 - Expedition - 99 - Radio Install
F150 - Ford
Expedition - Ford
Navigator - Lincoln
Radio Replacement
Document #: 356017
TM
1999
www.installdr.com
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Factory Radio
Other Documents Available For This Vehicle:
No additional documnets available at this time
Adobe Acrobat Reader Printing Tips:
New Radio
and radio installation kit
1) Select “FILE” then “PRINT” and select your printer.
2) In the print options box do the following:
A) Locate check box “Shrink to Fit”. Place check in box.
B) Locate box “Print Quality”. Select highest print dpi
allowed by printer.
C) If print quality listed is not as high as that printers normal
quality, press the “SETUP..” button. In the next screen,
press the “PROPERTIES” button and set the printers
print quality to the highest print dpi allowed.
Document Revision History
09/99
Document Creation
01/2000 Wiring Update
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
F150 - Ford
Expedition - Ford
Navigator - Lincoln
www.installdr.com
1999
Radio Replacement
Document #: 356017
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Overview Of This Radio Install
Step
Remove old radio from dash
Wire the new radio
Mount the new radio
Finishing the installation
Parts Needed For This Radio Install
What Section To Go To
Remove & Install
Wire New Radio
Mount New Radio
Remove & Install
Parts REQUIRED for the install
Snap on in dash wire harness
Radio dash installation kit
Description
** Please read instructions first
1999 Ford F150/Expedition kit
Optional parts for this install
None
Tools Needed To Complete This Install
TOOL TIPS:
Ford
Keys
OR
Coat Hanger
Hand tools needed
to remove radio
Solder/
Crimper
Voltage
Meter
Small
Battery
Accessory tools needed to test and
wire the new radio
PLUS: Wire ties or electrical tape: to neatly bundle and organize your
wires for a professional appearance.
Small Battery: use a battery to test speaker wires. Touching the (+) positive
and (-) negative baterry leads to a pair of speaker will cause the speaker to
make a “Pop” sound indicating that pair of wires goes to that speaker.
Voltage Meter: Always check +12 Volt power wires for voltage before
making wire connections. These wires will fluctuate between 10 and 14 Volts.
Solder Iron or Crimp Tool: make wire to wire connections using either a
solder iron and electrical tape, OR plastic crimp terminals found at most
hardware or auto parts stores.
Installation Difficulty Ratings
Easy. No advanced skills or specialty tools needed.
Basics. Simple tools required. Installs quickly.
Intermediate. Requires knowledge of tools, or disassembly of panels.
Advanced. Requires advanced tools, or extra time.
Difficult. Involves modifying or cutting of the installation area. Advanced
tools and/or skills required. Best if performed by experienced installers.
Do It Yourselfers
Basics
Professional Installer
Basics
Support Information If You Need Help
Supplemental information if you need help
Document Title
Basic DC electronics for automotive applications
Wire splicing: soldering vs. crimping
Why use radio installation kits
Mounting your radio to an installation kit
Why use an optional snap on wire harness
Wiring your new radio using a wire harness
Testing wires when installing a new radio
Document #
999001
999004
999005
999007
999008
999009
999013
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
F150 - Ford
Expedition - Ford
Navigator - Lincoln
TM
1999
Radio Replacement
Document #: 356017
www.installdr.com
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Remove Factory Radio
STEP 1:
STEP 2:
The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps
by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls
away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With
the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of
the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the
clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the
radio, see the diagram below.
Pull the radio from the dash. Unplug the
antenna cable from the rear of the radio. Unplug
the plastic wire harness connector from the
rear of the radio.
(Some Expeditions/Navigators may have a Ford
amplifier in the vehicle. This is the step you will
be able to tell)
Removing Ford Radios Using “U” Shaped Removal Keys
Insert the “U” shaped keys into
the holes as shown in the
diagram. Coat hangers can be
cut and bent into shape for a
quick, cheap replacement or
alternative when Ford keys are
not available.
Wiring The New Radio
Move to: Wire New Radio Section
In order for the radio to be
removed, clips attached to the
side of the radio must be moved
inward so the radio can slide out
of the dash. Insert the keys and
push each key out, away from
the radio. The ends of the keys
will press into the clips. While
pushing the keys outward, pull
and the radio should slide
forward out of the dash.
Mounting The Radio
Move to: Mounting New Radio Section
Ford Expeditions
Your Ford may have the Ford Premium Sound
System installed in it from the factory. This means
the speakers in the vehicle are actually powered
by a Ford amplifier instead of the amplifier inside
the radio (the amp is located away from the
radios dash location). The “Wire New Radio”
section will detail wiring for both standard Ford
radios and the wiring for Premium Sound System
radios. The only way to tell the difference between
a standard Ford radio and the Ford Premium
Sound System is to pull the radio and look at the
wire harness connectors plugged into the rear of
the Ford factory radio. You will be able to see the
2 different sets of wire harnesses in the “Wire
New Radio” section.
This is one style of radio installation kit
specifically designed for 1999 and
newer body style Ford F150’s,
Expeditions, and Navigators.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
F150 - Ford
Expedition - Ford
Navigator - Lincoln
www.installdr.com
1999
I
Radio Replacement
Document #: 356017
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Completing The Radio Installation
NOTE:
STEP 1:
STEP 2:
Once the radio is removed, you will notice the
rectangular opening in the dash where the
original radio was mounted. You will need to
adapt this opening over to accept a new
replacement radio. Depending upon your radio
installation kits design the kit should snap into
this rectangular opening
Mount the kit to the opening in the dash.
Once the radio installation kit is securely mounted
to the opening in the dash, mount and secure the
radio to the installation kit.
Plug in the antenna cable into the rear of the new
radio. Make sure all wiring for the new radio has
been completed and connect any connectors to
the new radio now.
STEP 3:
Reattach the plastic dash panel that surrounds
the radio.
The Installation Is Now Complete
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
F150 - Ford
Expedition - Ford
Navigator - Lincoln
www.installdr.com
1999
Radio Replacement
Document #: 356017
I
Cover
Page
Click on a link
tab to jump to
that page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Step By Step Wiring
Page 1 of 3
Auto Makers
Factory
Radio
New Radio
Wire Harness Inside Vehicles
Dash Which Plugs Into The
Rear Of The Factory Radio
Optional (STRONGLY
RECOMMENDED) Snap On Wire
Harness That Splices Into The
Wires Of The New Radio
(Note: the radio shown is for display purposes and may not be similar in
size or dimensions than the auto makers factory radio in your vehicle)
Wiring Instructions:
The power and speaker wires needed to connect the new radio are attached to
the connector of the wire harness located inside the vehicles dash. The Install
Doctor STRONGLY recommends using an optional snap on wire harness that
is specifically designed to snap into the vehicles dash wire harness connector.
This will keep you from cutting the vehicles wires. This optional snap on wire
harness will have wires on the opposite side of the connector that will allow
you to splice these wires to the new radios wires. The only other option is to
cut off the vehicles dash wire harness connector and splice the new radios
wires directly to these wires. The optional snap on wire harness takes all the
guess work out of trying to figure out what each wire is in the vehicles dash
wire harness. The optional snap on wire harness tell you what each wire is.
Supplemental information if you need help
Document Title
Testing wires when installing a new radio
Why use an OEM snap on wire harness
Wiring your new radio using a wire harness
Wire splicing: soldering vs. crimping
Document #
999013
999008
999009
999004
STEP 1
Ground Wire
STEP 2
+12 Volt
Battery Wire
Connect the +12 Volt Battery or Constant wire of the new radio to
either the +12 Volt Battery wire of a snap on wire harness OR connect
this wire to the +12 Volt Battery wire found in the wire chart above.
+12 Volt
Battery Wire
STEP 3
+12 Volt
Ignition Wire
Connect the +12 Volt Ignition or Switch wire of the new radio to
either the +12 Volt Ignition wire of a snap on wire harness OR connect
this wire to the +12 Volt Ignition wire found in the wire chart above.
+12 Volt
Ignition Wire
STEP 4
Power Antenna
Wire (if available)
If your vehicle has a POWER ANTENNA connect the
POWER ANTENNA wire of the new radio to either the POWER
ANTENNA wire on a snap on wire harness OR wire in chart above.
Power Antenna
Wire (if available)
STEP 5
Left Front Speaker Wires
Connect the LEFT FRONT speaker wires from the new radio to the
LEFT FRONT speaker wires on a snap on wire harness OR the
LEFT FRONT speaker wires found in the chart above.
Left Front Speaker Wires
STEP 6
Right Front Speaker Wires
Connect the RIGHT FRONT speaker wires from the new radio to the
RIGHT FRONT speaker wires on a snap on wire harness OR the
RIGHT FRONT speaker wires found in the chart above.
Right Front Speaker Wires
STEP 7
Left Rear
Speaker Wires
Connect the LEFT REAR speaker wires from the new radio to the
LEFT REAR speaker wires on a snap on wire harness OR the
LEFT REAR speaker wires found in the chart above.
Left Rear
Speaker Wires
STEP 8
Right Rear Speaker Wires
Connect the RIGHT REAR speaker wires from the new radio to the
RIGHT REAR speaker wires on a snap on wire harness OR the
RIGHT REAR speaker wires found in the chart above.
POWER AND SPEAKER WIRES FROM THE VEHICLES
DASH WIRE HARNESS OR SNAP ON WIRE HARNESS
POWER AND SPEAKER WIRES FROM NEW RADIO
Ground Wire
Connect the GROUND wire of the new radio to the ground wire of a
snap on wire harness OR crimp a ring terminal connector to this wire
and screw the ring terminal to metal inside the vehicles dash.
Right Rear Speaker Wires
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
F150 - Ford
Expedition - Ford
Navigator - Lincoln
www.installdr.com
1999
Radio Replacement
Document #: 356017
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Radio Wire & Color Code Information
Page 2 of 3
If Your Vehicle Has A Ford Premium Sound System Radio (Expeditions/Navigators)
This vehicle uses has a 2 pc wire harness. The black
connector is the input to the vehicles separate amplifer.
The second plug contains all necessary power wires.
Connector style used up to the
1988-89 production models
E
F
G
H
A
B
C
D
I
J
K L
M N O P
AS VIEWED FROM MATING END OF CONNECTOR
Connector style used beginning with the
1988-89 production models
A B C D E F
I
J
K L
G H
M N O P
Q R S T
U V W X
AS VIEWED FROM MATING END OF CONNECTOR
The Install Doctor STRONGLY recommends using a
snap on “integration” wire harness adapter which
will safely and easily allow you to connect a new
radio to the existing wires of the Ford radio system.
The “integration” wire harness will have all
necessary wires correctly labeled. This allows you to
follow the instructions on the previous page.
The Ford radio in your vehicle uses a separate Ford amplifer
that powers the speakers instead of the Ford radio powering
the speakers. This creates problems when installing a new
replacement radio into the vehicle. At the radio, the wire
harness inside the dash would normally have all necessary
speaker and power wires to install the new radio. However,
the speaker wires needed to install the new radio are plugged
into the Ford Premium Sound System amplifer which is
located away from the radio.
There are (2) options when installing a new radio you need to
consider before installing your new radio, one of which is not
recommended and requires extensive rewiring of every speaker
in the vehicle.
Option 1: you can choose to “integrate” into the Ford
amplifier. This is the simplest and easiest installation and for
the majority of new replacement radios this is the BEST
option. A Ford Integration Wire Harness is needed. This
wire harness is very similar to a standard Ford radio snap on
wire harness used to install radios in Ford vehicles with
standard radios but the harness will have a small box attached
to it which will allow you to splice the new radios speaker
wires directly to the wires of the integration harness. Inside
this box is electronics which will convert the new radios
speaker wire outputs into the necessary low voltage signal to
run the Ford amplifier. This means that the speakers in the
vehicle are being powered by the Ford amplifier, not the
amplifier inside the new radio. The information on this
sheet is structured to use OPTION 1 to integrate into the
original Ford amplifier. This has become the most
accepted method of installing a new replacement radio
in this type of Ford vehicle with the Premium Sound
System.
Option 2: you can also choose to “bypass” the Ford amplifer
in the vehicle and choose to power the speakers in the
vehicle with the amplifier inside the new radio instead of the
Ford amplifier. This is a 2 step process. You still have to
wire the new radio at the dash, and you have to find the
amplifier in the vehicle and add a jumper cable (included with
the bypass wire harness) to the amplifer; unplugging the
inputs and outputs of the amplifier and connecting them
together with the jumper from the bypass wire harness. This
method is only used for radios with more than 40 watts per
channel output.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
F150 - Ford
Expedition - Ford
Navigator - Lincoln
www.installdr.com
1999
I
Radio Replacement
Document #: 356017
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Radio Wire & Color Code Information
Page 3 of 3
If Your Vehicle Has A Standard Ford Radio
A B C D E F
G H
GRAY
BLACK
I
J
K L
M N O P
AS VIEWED FROM MATING END OF CONNECTOR
Ford Wire Harnesses
Up To 1998-1999 Production Models
Pin
What It Is
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Right Rear Spkr (-)
Right Rear Spkr (+)
Right Front Spkr (-)
Right Front Spkr (+)
Left Rear Spkr (-)
Left Rear Spkr (+)
Left Front Spkr (-)
Left Front Spkr (+)
Amplifier Turn On
Power Antenna Turn On
Ground Wire
Dash Light Dimmer Wire
+12 Volt Ignition Wire
+12 Volt Battery Wire
Typical Ford
In Dash Wire Color
"Typical" New Radio
Equivalent Wire Color
Blue
Purple w/ Black Stripe
White w/ Blue Stripe
Purple
White
Gray w/ Black Stripe
Blue w/ White Stripe
Gray
Red w/ Blue Stripe
Green w/ Black Stripe
White w/ Blue Stripe
Green
Blue w/ Orange Stripe
White w/ Black Stripe
Purple
White
Do Not Use For This Vehicle
Do Not Use For This Vehicle
Black
Do Not Use For This Vehicle
Orange (if available)
Red
Do Not Use For This Vehicle
Yellow
Note: using an optional snap on wire harness adapter will simplify the wiring. Most snap on
wire harness adapters have already converted and color coded the wires from the auto
makers in dash wire harness to match typical aftermarket radio wire colors.
** The wire colors listed in the chart above are typical for Ford vehicles during these years
but may not be the exact colors for this vehicle. This is another reason to use a snap on
wire harness adapter. **
A B C D E F
I
J
G H
K L M N O P
AS VIEWED FROM MATING END OF CONNECTOR
Ford Wire Harnesses
1998-1999 And Newer Production
Models
Pin
What It Is
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Right Front Spkr (-)
Right Front Spkr (+)
Right Rear Spkr (-)
Right Rear Spkr (+)
Dash Light Dimmer Wire
Ford Amplifier Ground Wire
Left Front Spkr (-)
Left Front Spkr (+)
Left Rear Spkr (-)
Left Rear Spkr (+)
Ground Wire
+12 Volt Ignition Wire
+12 Volt Battery Wire
Typical GM Factory
In Dash Wire Color
Typical New Radio
Equivalent Wire Color
Green w/ Orange Stripe
Lite Tan w/ Green Stripe
Orange w/ Maroon Stripe
Black w/ Purple Stripe
Do Not Use
Do Not Use
Do Not Use
Gray w/ Black Stripe
Gray
Purple w/ Black Stripe
Purple
Orange
Lite Blue w/ White Stripe
Orange w/ Green Stripe
Brown w/ Yellow Stripe
Gray w/ Lite Blue Stripe
Black w/ Green Stripe
Black w/ Pink Stripe
Lite Green w/ Black Stripe
White w/ Black Stripe
White
Green w/ Black Stripe
Green
Black
Red
Yellow
Note: using an optional snap on wire harness adapter will simplify the wiring. Most snap on
wire harness adapters have already converted and color coded the wires from the auto
makers in dash wire harness to match typical aftermarket radio wire colors.
** The wire colors listed in the chart above are typical for Ford vehicles during these years
but may not be the exact colors for this vehicle. This is another reason to use a snap on
wire harness adapter. **
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
F150 - Ford
Expedition - Ford
Navigator - Lincoln
TM
www.installdr.com
1999
Radio Replacement
Document #: 356017
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Mounting A Radio
NOTE:
This vehicle requires a special kit designed specifically for
Ford F-150’s, Expeditions, and Navigators.
All information needed to complete the mounting of the new
radio to the vehicles dash is included on this sheet. If you need
additional help, please consult the following tech documents:
Document Title
Why use radio installation kits
Mounting your radio to an installation kit
Radio security
‘DIN’ vs. Shafted radio - differences with
Document #
999005
999007
999010
999006
Ford F-150 / Expedition Specific
Radio Installation Kit
Opening In Dash
‘DIN’ Sleeve From New
Replacement Radio
Slide The ‘DIN’ Sleeve From The New Radio Into The
Kit And Bend Tabs On The Sleeve Behind The Rear Of
The Kit To Secure The Sleeve To The Kit.
Push The Kit Into The Dash Opening Until It Snaps Into
Place, Securing The Kit To The Dash.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising