STI Wireless Driveway MonitorTM

STI Wireless Driveway MonitorTM
Installation and Operation Manual
STI Wireless Driveway MonitorTM
Part of the Wireless Alert Series
Models: STI-34150 - Battery Power Kit
STI-34100 - Solar Power Kit
STI-34151 - Battery Powered Sensor
STI-34101 - Solar Power Sensor
Thank you for purchasing the STI Wireless Driveway Monitor. Your satisfaction is very important to us.
Please take the time to read this manual carefully to get the most from your new product.
Programming video - to add additional sensors
View adding additional sensor to receiver video at www.sti-usa.com/v3.
How the products works
Because of its patented magnetometer sensor transmitter system, the Driveway Monitor will only be
triggered by cars or trucks - not people, animals and so forth. When a vehicle passes the Motion Alert®
Sensor Transmitter next to the driveway, the receiver unit inside the office or home sounds a chime
and flashes the alert light. The earth has a uniform magnetic field around it. A vehicle creates a slight
disturbance in the earth’s field. The sensor transmitter detects this disturbance and transmits a signal
to the receiver.
Before you start
Refer to this drawing to become familiar with all the parts.
SENSOR
TRANSMITTER
CAP
SENSOR TRANSMITTER
PLASTIC FILM
REMOVE BEFORE USE
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR
TRANSMITTER
SENSOR
TRANSMITTER
BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSOR
TRANSMITTER
BOTTOM
MOUNTING
TUBE CAP
12” MOUNTING TUBE
MOUNTING STAKE
BATTERY POWERED SENSOR
TRANSMITTER
RECHARGEABLE AA
NiMH BATTERIES
SENSOR TRANSMITTER
BOTTOM SCREWS
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
12” MOUNTING TUBE
MOUNTING STAKE
SOLAR POWERED SENSOR
TRANSMITTER
12”MOUNTING TUBE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DOAND
NOT25+
DRIVEWAY
PULL ANTENNA!
FEET OR MORE FROM
STREET.
3' OR
LESS
Install batteries into the sensor transmitter
REMOVE
PLASTIC FILM
25'
OR MORE
Battery Powered (STI-34150 & STI-34151)
NG STAKE
DRIVEWAY
LACE SENSOR
1. Remove the sensor transmitter cap by turning it counterclockwise.
RANSMITTER 3' OR
2. WITHOUT PULLING ON THE BRASS ANTENNA OR ANY WIRES, grasp the outside
SS FROM EDGE OF
of25'
the battery/circuit board holder
MOUNTING
by theSTAKE
finger notches, twist gently and pull out.
RIVEWAY AND
R MORE FROM
STREET.
Insert
two “C” alkaline batteries (not included).
NOT NEEDED FOR POLE
TENNA
FROM BATTERIES
PULL ANTENNA!
REMOVE PLASTIC
FILM
MOUNT
INSTALLATION
DRI
25' OR MORE
3. Replace the battery holder/sensor transmitter and sensor transmitter cap.
SENSOR
TRANSMITTER
4. To test or program
sensor
transmitter, place the sensor transmitter on a table or
2 “C” 5-10
BATTERIES
counter approximately
ft. away from the receiver. Sensor transmitter can be
REMOVE
(NOTPLASTIC
INCLUDED)
TAB
activated byFROM
rotating
and will make a faint clicking noise to verify operation.
BATTERIES
5. Sensor should be programmed to receiver before mounting outdoors. Refer to
MITTER BASE
SENSOR TRANSMITTER
receiver instructions for programming. (Model STI-34150 is factory programmed
for
your convenience.) WALL MOUNT (INCLUDED)
SENSOR TAB
TRANSMITTER
DO NOT REMOVE PLASTIC
Sensitivity Adjustment
3' OR
LESS
SENSITIVITY
ADJUSTMENT
FINGER NOTCHES
NSMITTER CAP
MOUNTING
TUBE CAP
12'
MAX
RECHARGEABLE NiMH BATTER
SENSOR TRANSMITTER BOTT
SCREWS
WALL MOUNT (INCLUDED
NOT NEEDED FOR POLE
MOUNT INSTALLATION
BOTTOM
RECEIVER ANTENNA
MOUNTING
TUBE CAP
The factory default setting (HIGH) may be adjusted
by changing the jumper position inside the
SENSITIVITY
DO NOT
ADJUSTMENT
sensor transmitter.
PULL ANTENNA!
SPEAKER
REMOVE PLASTIC
FILM
OUNTING1.
TUBEUnscrew cap.
BUTTON
12”MOUNTING
TUBE
2. Position the jumper to desired sensitivity (as shown). GREEN
LACE
TON SENSOR
LED
SENSITIVITY
RANSMITTER 3' OR
SENSOR RED LED
RED LED • LOW: Position jumper on the two bottom pegs. FINGER NOTCHES
ADJUSTMENT
SS FROM EDGE OF
TRANSMITTER
SENSOR TRANSMITTER
MEDIUM: Completely remove jumper or hang on middle peg.
RIVEWAYAND•25'
CAP
2 “C” BATTERIES
R MORE FROM STREET.
•
HIGH:
Position
jumper
on
the
two
top
pegs.
STI-34104
OUNTING STAKE
TRANSISTOR
(NOT INCLUDED)
INDOOR RECEIVER
OUTPUT JACK
FINGER NOTCHES
3. Replace cap.
Medium Sensitivity Setting:
Low Sensitivity Setting:
•
•
•
SENSOR
TRANSMITTER MOUNTING STAKE
BASE
ANTENNA CONNECTOR
•
•
•
POWER CONNECTOR
NNA CONNECTOR
Jumper LocationRECEIVER ANTENNA
SENSIT
(BA
SE
TRANSM
High Sensitivity Setting:
MOUNTING
Jumper Location
TUBE CAP
L
H
Solar Powered (STI-34100 & STI-34101) 12” MOUNTING
RECEIVER
ANTENNA
TUBE
SPEAKER
TENNA
L
•
•
•
WALL MOUNT (INCLUDED)
NOT NEEDED
FOR POLE
Jumper
Location
MOUNT INSTALLATION
S
TRANSM
BO
MOUN
TUB
H
L
12” MOUNT
GREEN
REMOVE PLASTIC TAB
1. Remove
plastic film on solar BUTTON
panel.
LED
FROM BATTERIES
REDtransmitter
LED
2. Remove the bottom of the sensor
by removing the 3 screws on theSENSITIVITY JUMPERS
SENSITIVITY JUMPERS
SPEAKER (BATTERY TYPE)
bottom of the unit.
(SOLAR TYPE)
L
3. Remove the plastic tab between the batteries.
GREEN
BUTTON
TON
TRANSISTOR
LED Place the sensor
4.
Replace
the
bottom
of
the
unit
and
secure
with
the
3
screws.
REMOVE PLASTIC FILM
UTPUT JACK
RED LED
MOUNTING STAKE
RED LED
SENSIT
transmitter in direct sunlight 12’
for 48 hours.
MOUN
(BA
OR
PLACE SENSOR
MAX
3’OR
TRANSMITTER
3'
OR
Place batteries in a NiMH
metal
hydride) battery charger (before using). Once charged, return the batteries to the
POWER5.
CONNECTOR
ANTENNA
CONNECTOR
LESS (nickel
STI-34104
TRANSISTOR
LESS
EDGEwith
OF the 3 screws.
sensor transmitter.
Replace the bottom
andFROM
secure
INDOOR RECEIVER
OUTPUT
JACK
25' OR MORE
DRIVEWAY
AND 25'
DRIVEWAY
6. To test or program sensor transmitter,
place
theFROM
sensor
transmitter on a table or counter approximately 5-10 ft. away from
OR
MORE
STREET.
B
the receiver. Sensor can be activated by rotating. Sensor transmitter can be activated by rotating and will make a faint
POWER
CONNECTOR
ANTENNA
CONNECTOR
clicking
noise
to
verify
operation.
NNA CONNECTOR
7. Sensor should be programmed to receiver before mounting outdoors. Refer to receiver instructions for programming. (Model
STI-34100 is factory programmed for your convenience.)
Sensitivity Adjustment
STI-30104
The
factory default setting
LAMP
CONTROLLER
(OPTIONAL)
the sensor transmitter.
(HIGH) may be adjusted by changing the jumper position inside
1. ACRemove
ADAPTERthe bottom of the sensor transmitter by removing the 3 screws on the bottom
RECEIVER ANTENNA
of the unit.
2. Position the jumper to desired sensitivity (as shown below).
• LOW: Position jumper on the two
leftmost pegs.
SPEAKER
• MEDIUM: Completely remove jumper or hang from middle peg.
GREEN
BUTTON
• HIGH: Position jumper
on the two rightmost
pegs.
LED
RED
TRANSISTOR
3. Replace the bottom of the unit and secure LED
with the 3 screws.
OUTPUT JACK
Low Sensitivity Setting:
ANTENNA CONNECTOR
Jumper Location
+
+
-
RED LED
High Sensitivity Setting:
TRANSISTOR
OUTPUT JACK
Jumper Location
POWER CONNECTOR
—2—
SPEAKER
SENSITIVITY
ADJUSTMENT
BUTTON
B
GREEN
LED
•
•
•
POWER CONNECTOR
INDOOR RECEIVER
•
•
•
•
•
•
Jumper Location
Medium
STI-34104 Sensitivity Setting:
RECEIVER ANTENNA
-
ANTENNA CO
Installation Instructions
MOUNTING
TUBE CAP
To obtain optimal range
MOUNTING STAKE
WALL MOUNT (INCLUDED)
MOUNTING STAKE
NOT NEEDED FOR POLE
MOUNT INSTALLATION
The Solar Sensor Transmitter must be placed in an area that receives partial or full sunlight. For both models, be sure the
location of the sensor transmitter is at least 25’ back from the main road. For a typical 12’ wide driveway, it is recommended
12”MOUNTING
TUBE
the sensor transmitter be no more than 3’ away from the driveway
(see drawing).
Additional sensor transmitters may be required
for driveways exceeding 12’. Sensor transmitter may be placed up to 1,000 feet away from receiver; however, range may vary
depending upon environment and use of wireless telephones, wireless routers and other similar devices.
1. Place cap on tube.
2. Insert stake to opposite end of tube.
3. Place the tube (stake side down) into the ground within 3’ of the driveway
and more than 25’ from the road.
4. Gently hammer the cap side of the tube until stake is firmly in the ground.
5. Remove cap and place sensor transmitter on tube.
6. The sensor transmitter should have a clear line-of-site to the receiver to
improve performance.
7. Place the sensor transmitter so the vehicle does not pass between it and
the receiver.
STI recommends the use of the stake and tube included with your Driveway
Monitor. However, if you choose to mount the unit to an alternate mounting
device, please be sure the device is stable. STI does not recommend
mounting the sensor transmitter to a tree or a metal fence or gate.
TROUBLE
The RECEIVER does
not sound when a
vehicle passes.
25' OR MORE
3’OR
LESS
25' OR MORE
12’
MAX
DRIVEWAY
STI-30104
LAMP CONTROLLER
(OPTIONAL)
PLACE SENSOR
AC ADAPTER
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
GREE
LE
SOLUTION
TRANSISTOR
OUTPUT JACK
STI-30104
1. Check that the receiver is not in Temporary
or Permanent Silent Mode (red LED solid).
LAMP CONTROLLER
(OPTIONAL)
2. Check the sensor transmitter by picking
it up and rotating it. The sensor transmitter should make
AC ADAPTER
POWER CONNECTOR
a “faint clicking” noise.
RECEIVER ANTENNA
3. Check that the sensor transmitter and receiver are within operating distance from each other.
4. Check the sensor transmitter batteries and replace if necessary.
5. Reprogram the receiver using the steps in “Clearing the receiver memory”SPEAKER
and “Program a device
GREEN
into the receiver.”
BUTTON
LED
RED LED
The SENSOR
TRANSMITTER does
not activate when a
car passes.
TRANSISTOR
1. Check that the sensor transmitter and
receiver
OUTPUT
JACK are within operating distance from each other.
2. Change the Sensitivity in the sensor transmitter using the steps in “Sensitivity Adjustment.”
STI-34104
INDOOR
RECEIVER
3. Check that the sensor transmitter and receiver are located so a vehicle does not pass
between
them.
4. Change the location of the sensor transmitter by
placing
it closer to the edgeANTENNA
of the driveway.
POWER
CONNECTOR
CONNECTOR
5. Bring the sensor transmitter close enough to the receiver so the receiver button is visible. Test the
sensor transmitter by passing a steel shovel or large magnet around the sensor transmitter. The
sensor transmitter should make a “faint clicking” noise and the red LED on the receiver should
flash.
6. Check the sensor transmitter batteries and replace if necessary. On the solar powered driveway
monitor, make sure the sensor transmitter is in direct sunlight and has been charged in direct
sunlight for at least 48 hours after replacing batteries. Use only AA (1.2v) NiMH rechargeable
batteries.
7. Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”
The RECEIVER sounds
when there is no
vehicle passing.
1.
2.
3.
4.
Sensor transmitter mounted firmly and not effected by wind?
Sensor transmitter at least 25’ away from the main road?
Be sure there are no other metal objects near the sensor transmitter that may move.
Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”
Still having problems
Call STI Technical Support at 800-888-4784.
—3—
Important notice
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver’s • Consult a dealer or an experienced radio/TV technician for assistance
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly
approved by Safety Technology International, Inc. could void your authority to operate this equipment.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
Model 34101
FCC ID: TXL34101
IC: 6335A-34101
Model 34151
FCC ID: TXL34151
IC: 6335A-34151
Warranty information
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in
material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase.
Electronic warranty form at www.sti-usa.com/wc14.
Additional Wireless Alert Series Products
STI-34098
Single Channel Slave Receiver
STI-V34104 4-Channel Voice Receiver
STI-34108 8-Channel Receiver
STI-34101
Solar Powered Driveway Monitor Sensor
STI-34151
Battery Powered Driveway Monitor Sensor
STI-34201
Wireless Mail Alert Sensor
STI-34301
Wireless Garage Sentry Sensor
STI-34401
Wireless Universal Alert Sensor
STI-34501
Wireless Door Entry Alert® Sensor
STI-34601
Wireless Doorbell Button
STI-34701
Indoor Wireless PIR
STI-34752
Outdoor Wireless PIR
STI-6200WIR Wireless Fire Extinguisher Theft Stopper
STI-6200WIR4 Wireless Fire Extinguisher Theft Stopper w/Receiver
STI-6400WIR Wireless Exit Stopper Door Alarm
STI-6400WIR4 Wireless Exit Stopper Door Alarm with Receiver
STI-6517A
WIreless Stopper Station Shield with Sound
STI-6517B Wireless Stopper Station Shield with Sound and Transmitter
STI-6517C Wireless Stopper Station Shield with
Wireless Button
STI-6517D Wireless Stopper Station Shield with Button Sound and Transmitter
STI-30105
Extended Antenna
STI-30106
Mounting Replacement Kit (includes cap, wall mount, tube and stake)
STI-34105
Voltamax 12VDC (500mA) Power Supply
STI-34106Keyfob
STI-34109Repeater
STI-34188
8-Zone Relay Board
2306 Airport Rd • Waterford, MI 48327, USA
Phone: 248-673-9898 • Fax: 248-673-1246
info@sti-usa.com • www.sti-usa.com
Safety Technology International Ltd
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England • Tel: +44 (0)1527 520 999
Fax: +44 (0)1527 501 999 • info@sti-emea.com • www.sti-emea.com
Inst. Sht. WirelessDriveway JUNE2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising