Touch-Tone Controller Model PHC05 Owner`s Manual

Touch-Tone Controller Model PHC05 Owner`s Manual
Touch-Tone Controller
Model PHC05
Owner's Manual
1
CONTENTS
Features
Introduction
Important Notice
How it Works
Installation
Operation
From the Touch-Tone Controller's keyboard (Local)
From an outside telephone (Remote)
Problem Solving
Expand your system
2
2
3
4
4
5
5
5
6
7
Features:
Introduction:
• Turns on or off up to 10 lights/
The Touch-Tone Controller turns on up
to 10 lights or appliances from any
telephone in the world! So you can turn
on your central heating or air
conditioning before you leave work. Or
you can warm up or cool down your
vacation home from the airport. You’ll
never have to come home to a dark
home again.
•
•
•
•
•
•
appliances over the telephone.
Controls heating/air conditioning.
You’ll never have to come home to a
cold or dark home again.
Lets you remotely control up to 8
X10 PRO Modules from any
convenient location in your home.
You plug lamps and appliances into
X10 PRO Modules, and replace
wall switches with X10 PRO Wall
Switch Modules, to control important
inside and outside security lights.
(sold separately).
Sends signals to X10 PRO Modules
over your existing house wiring (no
additional wiring necessary).
Keep the Touch-Tone Controller by
your bedside and turn down the
heating without getting out of bed.
Turn on ALL lights connected to
Lamp Modules and Wall Switch
Modules with the touch of a button if
you hear a strange noise at night.
Turn off everything in the system with
one button.
It’s also a remote control so you can
control up to 8 lights and appliances
anywhere in your home. You can turn
on ALL lights connected to Lamp
Modules and Wall Switch Modules with
the push of a button if you hear a
strange noise at night. And you can turn
off everything in the system with one
button when you go to bed.
It can also flash a selected light or lights
anywhere in your home when the
phone rings (useful for the hearing
impaired).
2
IMPORTANT NOTICE
Be very careful when you use your Touch-Tone
Controller with any kind of appliance. For
example, if you use it to turn on a coffee pot
that happens to be empty you could burn out
its heating element, and possibly create a fire
hazard. It would be even more dangerous if you
used a remote control to turn on an electric
heater that had clothing draped nearby.
The telephone company attempts to notify you
in advance. If advance notice is not practical,
the telephone company notifies you as soon
as possible and advises you of your right to file
a complaint with the FCC.
Also, the telephone company can make
changes to its lines, equipment, operations, or
procedures that could affect the operation of
the Touch-Tone Controller. The telephone company notifies the owner of these changes in
advance, so the necessary steps can be taken
to prevent interruption of telephone service.
USE YOUR TOUCH-TONE
CONTROLLER CAREFULLY
IMPORTANT:
The Touch-Tone Controller can be connected
to most telephone lines. However, each telephone or telephone device that is connected
to the telephone line draws power from the telephone line. This is referred to as the device’s
ringer equivalence number, or REN. If more
than one telephone or other device is connected to the same line, add up all the RENs.
If the total is more than five, the telephones
might not ring. In rural areas, a total REN of
three might impair ringer operation. If ringer
operation is impaired, remove one of the devices from the line.
If a problem arises with your telephone service
after you have connected the Touch-Tone
Controller, disconnect the unit to see if the
problem is caused by its use. If the Touch-Tone
Controller is at fault, leave it disconnected and
have it replaced. If the telephone company
makes a service call to your home and
determines that the Touch-Tone Controller has
caused the problem, they have the right to
charge you for a service call.
NOTE 1:
If you own an answering machine, set it to
answer first. You can set the Touch-Tone
Controller to answer either 15 seconds or 35
seconds after ringing is detected.
Note: The Controller must not be connected
to:
• Coin-operated systems
• Party-line systems
• Most electronic key telephone systems
NOTE 2:
The Touch-Tone Controller ALWAYS answers
a call. If you have an answering service
provided by your phone company, the service
picks up if your phone is not answered, so in
this case the service will never pick up. If you
have this kind of answering service, install the
Touch-Tone Controller on a separate phone
line.
The Touch-Tone Controller complies with Part
68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN
to the local telephone company. Both numbers
are shown on the bottom of the console.
In the unlikely event that the Touch-Tone
Controller causes problems on the telephone
line, the telephone company can disconnect
service.
© 1999 X10 PRO
3
HOW IT WORKS
INSTALLATION
The Touch-Tone Controller controls
lights and appliances throughout your
home from any convenient location. It
transmits signals to X10 PRO modules
over your existing house wiring. You
plug lamps into Lamp Modules,
appliances into Appliance Modules,
and replace wall switches with Wall
Switch Modules. You can then control
virtually everything electrical in your
home.
1. Plug the power cord into any
functioning 120V AC outlet and plug
the phone cord into an RJ11 phone
jack. (Connect to the unit first, then
to the wall jack).
2. Using a small screwdriver, set the
Touch-Tone Controller’s Housecode dial to the same letter as your
X10 PRO Modules (A through P).
3. Set a Personal Identification Number
(PIN) (0-999). Use one, two, or three
digits as desired. Set all dials to the
OFF position for no security (PIN)
code (not recommended).
4. Set the Ans Delay switch to Min (for
15 seconds delay), or Max (for 35
seconds delay) before the unit
answers a call.
5. Install and set up X10 PRO Modules
(sold separately). Refer to the
Modules instructions.
6. Set all your Modules to the same
Housecode as you set on the TouchTone Controller.
7. Set each Module to a Unit Code
between 1 and 8. Any Module(s) set
to the same number as the third digit
on the security code dial (on right)
flashes on and off when the phone
rings.
The Touch-Tone Controller tells the
Modules what to do. Command signals
are sent over your existing house wiring
to the Module(s) of your choice. The
Modules respond to the signals. The
Lamp Module turns on and off any lamp
up to 300 watts. It can also be dimmed
and brightened from other types of
X10 PRO Controller. The Appliance
Module turns on and off appliances
such as a window fan, air conditioner,
or stereo, etc. It can also be used for a
lamp but can’t dim or brighten it. The
Wall Switch Module turns on and off
any incandescent light up to 500 watts.
It can also be dimmed and brightened
from other X10 PRO controllers.
Touch-Tone Controller
Wall
Switch
Module*
Mini Timer*
Lamp
Module*
Appliance
Module*
* Sold separately
4
OPERATION
REMOTE
1. Call home from any touch-tone
phone. If you do NOT own an
answering machine, the Touch-Tone
Controller answers after 15 or 35
seconds (depending on the position
of the delay switch) and gives three
beeps. If you DO own an answering
machine it will answer first. In this
case the Touch-Tone Controller will
do nothing until you enter its PIN.
2. Enter your security code (PIN) from
the touch tone keypad on the phone
you are calling from. You hear
another three beeps.
3. Press the touch tone number key
corresponding to the X10 PRO
Module you want to control. Use the
0 digit for Module number 10.
4. Press * for ON or # for off. You hear
3 beeps after on, 2 beeps after off.
You hear one long beep if you press
an invalid key.
You may continue to enter a number
followed by * or #. If you press 1, 2, *
you will turn on Modules 1 and 2, not
Module 12. You can only control
Modules 1 thru 10 from an outside
phone (1 thu 8 from the Touch-Tone
Controller’s keyboard). Enter the
security PIN code only once at the
beginning. If you make a mistake when
entering digits, press * or # then enter
them again. The Touch-Tone Controller
keeps the line engaged for 30
seconds after the last key you press.
LOCAL
To Turn a light or appliance ON or
OFF from the keyboard.
Press and release the number button
(1 -8) corresponding to the Unit Code
you set on the Module you want to
control. Then press and release the
ON or OFF button.
To turn on ALL lights from the
keyboard.
Press and release the All Lights On
button. This turns on all lights
connected to Lamp Modules and Wall
Switch Modules which are set to the
same Housecode as the Touch-Tone
Controller. This button does not affect
Appliance Modules.
To turn off all lights and appliances
from the keyboard.
Press and release the All Units Off
button. This turns off all Modules which
are set to the same Housecode as the
Touch-Tone Controller, including
Appliance Modules.
Number keys
Security Code
(000 to 999). Last
digit sets code for
“flashing light.”
Housecode
Set all your
Modules to
the same
letter
All Lights On key
On/Off keys
All Units Off key
Slide Switch. Set to
Min (15 secs) or Max (35
secs) answer delay.
5
PROBLEM SOLVING
POWER INTERRUPTIONS
When power is restored after a power
outage, Lamp Modules and Wall
Switch Modules will normally be off.
Appliance Modules stay in the state
they were in before the power
interruption.
MANUAL (LOCAL) CONTROL
Lights and appliances connected to
plug-in Modules can be turned ON with
their own power switch. Simply turn the
switch off and on once or twice to
activate the Module. For lamps with
three way bulbs you might have to
operate the switch a few times. Wall
Switch Modules can be turned on and
off from their own push button. The
slide switch under the push button is
to remove the power when changing a
light bulb.
SAFETY PRECAUTIONS
Don’t exceed the ratings of the
Modules (see back of Modules for
details).
Don’t use an Appliance Module for
anything that could be dangerous if
turned on remotely while unattended
(a portable heater for example).
Don’t use the Wall Switch Module for
fluorescent lamps, ceiling fans, low
voltage lights, or any kind of appliance.
Use for Incandescent lamps up to 500
watts only. Don’t use to control an
outlet.
If a particular Module won’t go on
or off from the buttons on the
Touch-Tone Controller:
Check that you have power to the outlet
controlling the Module and that the
switch on the light or appliance is on.
Check that the Unit Code on the Module
is set to the correct number. Check that
the Housecode on the Module and the
Touch-Tone Controller are set to the
same letter.
Try plugging the Module and the TouchTone Controller into the same outlet
(top and bottom). If the Module doesn’t
work in ANY outlet, replace the Module.
If you can’t control ANY modules
from the Touch-Tone Controller:
Check that you have power to the outlet
for the Touch-Tone Controller. Check
that the Housecode on the Touch-Tone
Controller is set correctly.
If the Touch-Tone Controller
answers the phone too soon and
prevents your answering machine
from picking up:
Set the MIN MAX Delay Switch on the
Touch-Tone Controller to MAX (35
seconds).
INTERCOM SYSTEMS
Intercom systems that send voice
signals over existing house wiring can
interfere with the operation of the
Touch-Tone Controller when the
intercom is in use. If the intercom has
its own separate wiring or uses wireless
Radio Frequency (RF) transmissions
it will not cause a problem.
6
EXPAND YOUR SYSTEM
Mini Timer PHT02
Lamp Module PLM01
A Controller, Timer and Alarm Clock all
in one! Programs up to 4 modules to go
on and off at specific times, twice a day.
Controls 8 modules instantly. Dims
lights too.
Can be Dimmed and Brightened from
any X10 PRO Controller. Responds to
“All lights on”. Rated for 300 W.
Incandescent only.
Appliance Module - PAM01/PAM02
Maxi Controller PHC02
Two pin polarized (PAM01) or 3 pin
grounded (PAM02). For controlling an
air conditioner, stereo, etc. anywhere in
the home. Rated 15A for heaters,
coffee pots etc.; 1/3 H.P. for motors;
400W for TVs; 500W for lamps.
Lets you control up to 16 X10 PRO
Modules at the touch of a button from
anywhere in the house. Dims lights too!
Mini Controller PHC01
Lets you control up to 8 X10 PRO
Modules at the touch of a button from
anywhere in the house. Dims lights too!
Wall Switch Module PLW01
For controlling important indoor and
outdoor security lights. Replaces your
existing wall switch and installs like a
regular dimmer. Dimmed/brightened
from any X10 PRO Controller. Rated
500W incandescent only.
2-Way Home Control Interface
CM11A
Set up from an IBM compatible PC to
control up to 256 X10 Modules.
ActiveHome software & cable included.
3 - Way Wall Switch Module PLW02
PDT20 Digital Thermostat
For controlling a light which is controlled
by two switches. Same features as
PLW01.
Full functioned thermostat control
manually and via X-10 signals from any
X-10 PRO Controller.
Split Receptacle Module PAO11
Wireless Remote Control System
PHK05
Replaces existing wall outlet. The top
outlet functions like an Appliance
Module, the bottom one is a regular
outlet. Rated 15A. Controls ANYTHING
which normally plugs into a regular AC
outlet.
Lets you control 16 X10 PRO Modules
from inside or outside your home. Can
also dim and brighten Lamp Modules
and Wall Switch Modules. The PHR03
Handheld RF Remote transmits to the
Transceiver PAT01 controlling
X10 PRO devices.
Universal Module PUM01
Isolated contact relay and beeper. Can
be set for momentary or continuous
operation. Used to operate OEM
devices requiring a dry contact input.
7
24 MONTH LIMITED WARRANTY
X-10 PRO WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL WORKMANSHIP
FOR A PERIOD OF TWO (2) YEARS FROM THE DATE CODE OR FROM THE ORIGINAL DATE OF
PURCHASE (WITH RECEIPT). X-10 PRO AGREES TO REPAIR OR REPLACE AT ITS SOLE DISCRETION, A DEFECTIVE X-10 PRO PRODUCT IF RETURNED WITHIN THE WARRANTY PERIOD.
IF SERVICE IS REQUIRED UNDER THIS WARRANTY:
1. RETURN THE DEFECTIVE X-10 PRO PRODUCT WITH A PROOF OF PURCHASE TO THE ORIGINAL COMPANY (X-10 PRO DISTRIBUTOR) WHO YOU PURCHASED THE PRODUCT FROM.
2. X-10 PRO IS NOT RESPONSIBLE FOR SHIPPING DAMAGE. UNITS TO BE RETURNED SHOULD
BE PACKED CAREFULLY.
THIS WARRANTY DOES NOT EXTEND TO ANY X-10 PRO PRODUCTS WHICH HAVE BEEN SUBJECT TO MISUSE, NEGLECT, ACCIDENT, INCORRECT WIRING OR TO USE IN VIOLATION OF OPERATING INSTRUCTIONS FURNISHED BY US, NOR EXTEND TO ANY UNITS ALTERED OR REPAIRED
FOR WARRANTY DEFECT BY ANYONE OTHER THAN X-10 PRO. THIS WARRANTY DOES NOT
COVER ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND NO REPRESENTATIVE OR PERSON IS AUTHORIZED TO
ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF OUR PRODUCTS.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, AND/
OR THE EXCLUSIVE OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO THE ORIGINAL CUSTOMER. THIS
WARRANTY GIVES YOU SPECIFIC RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH
VARY, FROM STATE TO STATE.
X-10 PRO
Tampa, Florida 33618
Sales Phone Number (800) 411-2888
Technical Support
For Distributors and Contractors Only (800) 832-4003
Web Site: http://www.x10pro.com
8
PHC05_1-9/99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising