ZENMUSE H4-3D User Manual V1.0 2015.1 Warning & Disclaimer The Zenmuse H4-3D gimbal is calibrated before delivery. No adjustment or modification to the gimbal is required or recommended. Ensure the camera is mounted to the gimbal before powering on your aircraft. The H4-3D gimbal is finely calibrated according to the specified camera model and lens (GoPro Hero4 Black) before delivery. You do not need to perform extra calibration. Do not attempt to modify the gimbal or mount extra components/devices (such as a filter, lens hood, etc.) to the camera. Be sure to use a DJI approved battery, otherwise the performance of the gimbal may be affected. The H4-3D gimbal is compatible with following DJI flight control systems: NAZA-M, NAZA-M V2, WooKong-M, Phantom 2 and A2. To optimize the gimbal’s performance, download the relevant Assistant for your flight controller and upgrade the firmware. Make sure to operate your aerial system in the safest manner possible. We strongly recommend that you remove all propellers, use a power supply from the R/C system or flight pack battery, and keep children away when calibrating and configuring the gimbal. Observe the procedures contained in this manual to mount and connect gimbal to your aircraft. Users of this product should respect the AMA’s National Model Aircraft Safety Code. DJI has no control over use, setup, final assembly, modification (including use of non-specified DJI parts i.e. motors, ESCs, propellers, etc.) or misuse, and no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. DJI assumes no liability for damage(s), injuries or legal responsibilities incurred directly or indirectly from the use of this product. DJI and Zenmuse are registered trademarks of DJI. Names of product, brand, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and manual are copyrighted by DJI with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI. Legend Important 2 © 2015 DJI. All Rights Reserved. Hints and Tips Contents Warning & Disclaimer 2 Legend 2 Profile 4 In The Box 4 Installation 6 Gimbal Description 6 Installing H4-3D onto an Aircraft 7 Camera Installation 11 Final Checks 11 GCU Connection 12 Connecting the GCU and Flight Control System 12 GCU and Flight Control System Connection 13 Video Connection 14 Configuration 16 Driver and PC Assistant Installation 16 PC Assistant Interface 16 Channel Setting 16 Firmware & Software Upgrade 17 Test Flight 18 Pre-flight Checklist 18 Gimbal Test 18 Appendix 19 Troubleshooting 19 Settings When Using the A2 Flight Control System 19 Specifications 20 © 2015 DJI. All Rights Reserved. 3 Profile The Zenmuse H4-3D gimbal offers excellent stabilization features for aerial hobbyists and professional aerial photographers. Powered by a built-in IMU (Inertial Measurement Unit) and a special servo module, this gimbal is built to hold a GoPro camera and enables stable, quality aerial photography. Profile The H4-3D gimbal is designed for GoPro Hero4 Black camera. Using other type of camera may cause the gimbal to function abnormally. In The Box Gimbal × 1 Built-in servos and a stand-alone IMU provide yaw, roll, and tilt stabilization. Pre-installed vibration absorbers greatly reduce vibrations. Damping Unit × 1 The upper plate of the damping unit is used to connect the gimbal to your aircraft. An integrated bottom damping plate minimizes installation time. Accessories Pack – Spare Vibration Absorbers × 4 Spare vibration absorbers for the damping unit. Use one set at a time. Accessories Pack – Anti-drop Kit × 4 Spare anti-drop kits that are used to secure the upper and bottom plates of the damping unit. Accessories Pack – Camera Securing Bracket × 1 Camera mounting bracket. 4 © 2015 DJI. All Rights Reserved. ZENMUSE H4-3D User Manual Accessories Pack – Spare Screws × 1 M2.5x6.3: Used to mount your camera to the gimbal. M2.5x5: Used to secure the gimbal to the damping unit. M3x8, M3x6.5: Used to secure the gimbal to the aircraft. In The Box Accessories Pack – USB Video Output Module × 1 Connects to the USB port of your camera, for transmitting video. Accessories Pack – Anti-interference Board × 1 Serves as the connecting board between the G8 port on the gimbal and an 8-pin cable. This board is only available with the H4-3D gimbal that does not come with a GCU unit (namely, the H4-3D specifically designed for a Phantom 2). You can mount the H4-3D gimbal onto other DJI aircraft by using the below accessories. You may purchase the accessories according to your aircraft type. Gimbal Controller Unit (GCU) × 1 Connect the Gimbal Controller Unit to your flight control system using CAN-Bus. Power the GCU and gimbal through a 3S~6S power cable. Gimbal Video Signal Cable × 1 For connecting the gimbal controller unit to your wireless video transmission module. Transmits the video signal. CAN-Bus Cable × 1 Use CAN-Bus to connect the GCU to your flight control system. 8-Pin Cable × 1 For connecting your Phantom 2 to the G8 port of the GCU. Phantom 2 (old version) Adapter For installing the H4-3D gimbal onto older versions of the Phantom 2. © 2015 DJI. All Rights Reserved. 5 ZENMUSE H4-3D User Manual F450 & Phantom 1 Adapter For installing the H4-3D gimbal onto a F450 or Phantom 1. Installation F550 Adapter For installing the H4-3D gimbal onto a F550. Must be used with the above F450 adapter. Installation Gimbal Description Ensure the gimbal servos are unobstructed, otherwise they may be damaged during operation. If the gimbal becomes obstructed during operation, power off and clear all obstructions immediately. Always mount the camera before powering on the gimbal.         Yaw servo driver module  Upper plate of the damping unit  Vibration absorbers  Bottom plate of the damping unit 6 © 2015 DJI. All Rights Reserved.   Tilt servo driver module  Roll servo driver module  Camera mount  8-pin connector port (to GCU/Phantom 2) ZENMUSE H4-3D User Manual Installing H4-3D onto an Aircraft Installing H4-3D onto a Phantom 2 (new version) There are two versions of the Phantom 2. The latest Phantom 2 can hold the H4-3D gimbal directly, while the older version of the Phantom 2 requires an adapter to hold the H4-3D. The difference between the two versions can be seen on the bottom of Phantom. Installation Phantom 2 (new version) Phantom 2 (oid version) Follow the instructions below to install the H4-3D gimbal onto a Phantom 2 (new version). 1. Insert the securing pins into the holes on the upper plate of the damping unit as shown below. Then, attach the upper plate of damping unit to the Phantom 2 with four M3x5 screws. © 2015 DJI. All Rights Reserved. 7 ZENMUSE H4-3D User Manual 2. Attach the bottom plate of the damping unit to the upper plate. To do this, insert the securing pins on the tip of the vibration absorbers into the mounting holes on the bottom plate. Installation 3. Cover the securing pins with washers to lock the damping unit in place. Only push the washers past the first nut. 4. Plug the 8-pin cable from the Phantom 2 into the Phantom 2 port on the anti-interference enhancement board. Then use the supplied 8-pin cable to connect the H4-3D port on the antiinterference enhancement board to the 8-pin port on the gimbal. 8 © 2015 DJI. All Rights Reserved. ZENMUSE H4-3D User Manual Installing the H4-3D onto Other DJI Aircraft You can install the H4-3D onto other DJI aircraft by using the corresponding adapter. Refer to the relevant instructional video or user manual for more details. 1. Use the Phantom 2 (old version) adapter to install the H4-3D onto previous versions of the Phantom 2. Installation Phantom 2 (old version) Phantom 2 (old version) adapter H4-3D 2. Use the Phantom 1 adapter to install the H4-3D onto the Phantom 1. Phantom 1 Phantom 1 adapter H4-3D GCU © 2015 DJI. All Rights Reserved. 9 ZENMUSE H4-3D User Manual 3. Use the F450 adapter to install the H4-3D onto the DJI F450. DJI F450 F450 adapter H4-3D GCU Installation 4. Use the F450 adapter and F550 adapter to install H4-3D to DJI F550. DJI F550 F450 adapter F550 adapter H4-3D GCU Aircraft, camera, and accessories are not included with the gimbal. Camera must be aligned to face the nose of the aircraft, and the gimbal should be parallel with the aircraft itself. The gimbal is calibrated before delivery. Do not attempt to adjust or calibrate it yourself. Do not remove any screws in the gimbal, which may result in reduced performance or failure. Do not unplug any cable attached to the gimbal ports or change the mechanical structure of the gimbal. The 8-pin port on the H4-3D should only to be used to connect the gimbal to your aircraft. Do not connect other devices (such as a 5.8G video downlink transmitter) to this port, otherwise the gimbal may be damaged. 10 © 2015 DJI. All Rights Reserved. ZENMUSE H4-3D User Manual Camera Installation Follow the instructions below to mount your GoPro Hero4 Black camera. Visit http://www.dji.com/product/zenmuse-h4-3d/video and watch the installation video tutorial before mounting your GoPro camera to the H4-3D gimbal. The gimbal cables are delicate items, handle with extreme care. Always check all connections before each flight and ensure they are secure. Final Checks Ensure the installed damping unit is parallel with the aircraft. © 2015 DJI. All Rights Reserved. 11 Installation 1. Connect the video output board to the gimbal using the connection cable. Ensure the connection orientation is correct. 2. Mount the camera onto the gimbal and secure the camera with the camera bracket and screws. 3. Firmly insert the video output board into the mini-USB port on the camera to complete the installation. GCU Connection Skip this chapter if you have the Phantom 2 version of the H4-3D gimbal, as it does not come with a GCU. The GCU must be connected to the flight control system before it is powered on. Be sure to mount the camera onto the gimbal before powering on the aircraft and the gimbal. Otherwise the servos may be damaged due to an incorrect center of gravity. Re-calibrate the remote control whenever the NAZA-M firmware is upgraded. Ensure all connections are correct, otherwise damage to the gimbal or the flight control system may occur. GCU Connection GCU Port Description 3S~6S G8 Connect to a battery for GCU or gimbal power. Connect to the G8 pin port on the gimbal for signal transmission. Connect to a PC to upgrade the firmware using PC Assistant. Connect to a flight control system. Connect to a wireless video downlink module. Connecting the GCU and Flight Control System The GCU can be either vertically or horizontally installed on the Phantom 2. Follow the procedure below to complete the connection between the GCU and the flight control system. 1. Upgrade the flight controller’s firmware and PC Assistant to the latest version, as shown in the table below: Flight Controller A2 WKM NAZA-M V2 NAZA-M PC Assistant V1.20 (or higher) V2.00 (or higher) V2.12 (or higher) V2.12 (or higher) Firmware Version V2.10 (or higher) V5.22 (or higher) V3.12 (or higher) V3.12 (or higher) 2. Complete the connection to the flight control system as shown on the table below. NAZA-M users need a PMU V2 module (a NAZA-M V2 accessory) to make the CAN port connection. Flight Controller A2 WKM NAZA-M V2 or NAZA-M Connect the PMU’s X1 Connect the PMU’s Connect the PMU V2’s X3 Main Controller and port to the X1 port of the X1 port to the X1 port port to the X3 port of the PMU connection Main Controller. of the Main Controller. Main Controller. PMU Power Cable connection Connect the power cable to a connecter, or solder the power cable to the central board as required. (GPS/Compass Module and Flight Control System Connection Connect the GPS/ Connect the GPS/Compass Connect the GPS/ Compass module to a module to the GPS port of Compass module to the spare CAN-Bus port the PMU V2. CAN 2 port on the A2. on the PMU. 12 © 2015 DJI. All Rights Reserved. ZENMUSE H4-3D User Manual Refer to GCU and Flight Control System Connection for more information about the connection. For details on the flight control system connections, refer to the corresponding flight control system user manuals. 3. Connect the GCU to the flight control system. Then connect the 8-Pin cable of the gimbal to the G8 port on the GCU. Flight Controller A2 WKM NAZA-M V2 NAZA-M Connect to the CAN 2 port on the A2. GCU Power Cable Connection Connect the power cable to a connecter or solder the power cable to the central board as needed. Gimbal Tilt Control Channel Connect the GCU to a Connect the GCU to the CANspare CAN-Bus port on Bus port on the PMU V2 the WKM system. module. H4-3D X3 X1 4. Connection is complete. Power on the aircraft to launch. 5. To fully utilize the gimbal, you will also need to configure its tilt function. Each flight control system assigns a specified channel (X3 channel for WKM, X1 for NAZA-M, and H4-3D for A2) for tilt control. To activate the tilt function, set up the channel in the PC Assistant and ensure the connection between the receiver and the main controller is correct. Refer to the gimbal PC Assistant for details. GCU and Flight Control System Connection S GP C OM P A S S positive pole(+) Battery (3S~6S) negative pole(-) 3S 6S H -3D AV GCU 2S V-SEN 6S [email protected] PMU X1 PW ([email protected]) WKM Connection Diagram The PMU and GCU can both connect to the same LiPo 3S-6S battery. The GCU can be connected to any CAN ports on the PMU or to the CAN port on the GPS. (Any spare CAN port on the WKM system.) Control the tilt motion via the X3 channel. Properly configure the corresponding channel on your remote controller. © 2015 DJI. All Rights Reserved. 13 GCU Connection GCU and Flight Control System Connection ZENMUSE H4-3D User Manual A NAZA LED E T MUTI POTOR V2 M3 R 6S NAZA 2S 6S H -3D PMU GCU V-SEN M4 U M5 X1 M6 EXP DIY power connector 3S X2 [email protected] F1 X3 X3 V2 M1 M2 F2 -+ +- AV GPS EXP. NAZA-M V2 Connection Diagram V-SEN LED + 2S-6S - GCU Connection Leave as-is 3S A M1 E M2 LED 6S T H -3D M3 R DIY power connector NAZA 2S 6S PMU M5 X1 M6 X2 V-SEN [email protected] M4 U EXP AV GCU F1 X3 X3 V2 F2 -+ +- GPS EXP. NAZA-M Connection Diagram The PMU and GCU can both connect to the same battery. Control the tilt motion via the X1 channel. Properly configure the corresponding channel on the remote controller. Video Connection The camera’s video signal is transferred to your wireless video transmission module from the GCU by using the gimbal video signal cable. Follow the figure below to complete the connection. Wireless Video Transmission Module Air System External Power Leave as-is Power Gimbal Video Signal Cable 3S 6S H-3D Yellow GCU AV Video Signal GND Video Signal(Yellow:AV) GND(Black: 14 © 2015 DJI. All Rights Reserved. ) Video Signal Port ZENMUSE H4-3D User Manual 1. Solder the Video Signal/GND cables to your wireless video transmission module (air system). 2. Plug the gimbal video signal cable into the GCU video signal port. Ensure the wireless video transmission unit is connected to the GCU before powering on the aircraft. Use of a standard gimbal video signal cable is recommended. Make sure you solder the gimbal video signal cable to the wireless video transmission module firmly. Insulate all the cables to prevent short circuiting. The GCU does not provide power to the wireless transmission module. Refer to the wireless video transmission module manual for details on the power supply connection. Gimbal Video Port AV Signal Monitor AV Input AV Signal Camera Interface Wireless Video Transmission Module Ground System GCU AV Signal 8-Pin cable Wireless Signal 5.8G/2.4G/1.2G G8 AV Signal AV Camera GCU Connection The diagram below shows how video signal flows from the camera to the gimbal. Should errors occur, examine each step to locate the source of the problem. Gimbal Video Signal Cable Wireless Video Transmission Module Air System Supplied by user © 2015 DJI. All Rights Reserved. 15 Configuration Driver and PC Assistant Installation The contents of this chapter do not apply to the Phantom 2 version of the gimbal. Refer to the Phantom 2 PC Assistant information in your Phantom 2 User Manual instead. 1. Ensure the drivers for the flight control system are properly installed. 2. Download the PC Assistant from the official DJI website. 3. Launch the PC Assistant installer and follow each step to complete the installation. 4. Run the PC Assistant. PC Assistant Interface Configuration With the PC Assistant running on your PC, connect the GCU to your PC by using a Micro-USB cable. Then power on the GCU. Channel Setting You can adjust the available range of camera tilt in the PC Assistant by adjusting the slider. Tilt Upwards 16 © 2015 DJI. All Rights Reserved. Tilt Downwards ZENMUSE H4-3D User Manual Firmware & Software Upgrade Firmware Upgrade CMU stands for “Camera Multi Unit”, which is the management module for the camera. To eliminate interference from the main controller, DJI recommends you disconnect the CAN-Bus cable between the GCU and main controller before you upgrade the firmware. Double check your set parameters once you have finished upgrading the firmware. Repeat the above steps if the DJI server is experiencing heavy traffic or the firmware upgrade fails. Software Upgrade Click Info Software Info. If the latest version is newer than your current version, please upgrade your software. Obtain your gimbal’s serial number (SN) by clicking the “Info” “SN”. The serial number is a 32 digit authorization code that is used to activate the gimbal. This number is set at the time of manufacture, before shipment. You may be prompted to fill in a new SN if you purchase a new feature. If you fill an invalid SN more than 30 times, the gimbal will be locked and you will have to contact our customer support to unlock the gimbal. © 2015 DJI. All Rights Reserved. 17 Configuration Follow the procedures below to upgrade the H4-3D’s firmware. Failure to follow these instructions carefully may damage the gimbal. 1. Ensure your computer has access to the internet. 2. Close all other applications (including anti-virus programs or firewalls) before upgrading the firmware. 3. Make sure the power supply is securely connected. DO NOT unplug the power supply before the upgrade is complete. 4. Connect the GCU to your PC through a Micro-USB cable. DO NOT disconnect the cable until the firmware upgrade is complete. 5. Launch the PC Assistant and wait until the connection is established. 6. Select “Upgrade” Main Control, IMU and CMU. 7. The DJI server will check the current firmware version. 8. If a newer firmware is detected, the PC Assistant will download and upgrade the firmware automatically. 9. Wait until the upgrade completes. 10. Click “OK” and power cycle (turn off, then turn on again) the system to finish the upgrade process. Test Flight Pre-flight Checklist For safety reasons, check all of the following items before each flight: 1. The gimbal is firmly installed onto the aircraft, and the camera is mounted correctly. Make sure the camera is aligned facing the nose of the aircraft. 2. All cables are firmly and correctly connected. 3. The gimbal video signal cable is firmly soldered in place. 4. The wireless video transmission module is connected to the GCU before powering on the system. 5. The remote control is properly configured. 6. The camera is correctly connected to the gimbal. 7. The GCU and flight control system are correctly connected. 8. The flight control firmware is updated to the latest version. Gimbal Test Test Flight 1. Ensure all batteries are fully charged. 2. Turn on the remote control. 3. Power on your camera, then power on the gimbal and wait until gimbal’s self-test completes. 4. The camera lens should be pointing in the same direction as the aircraft nose. All three axes of gimbal should be in the positions depicted in the diagram above. 5. Toggle the tilt control switch on your transmitter and make sure it is working properly. Check that the gimbal moves in the correct direction when the switch is toggled. If not, check your settings. 6. When the test is complete, power off the gimbal first, then the camera. If the gimbal is not working properly, refer to Troubleshooting (P19) for solutions. Place the aircraft on a flat surface during the test. If you choose to hold the aircraft while testing, do not tilt the aircraft more than 35°. Do not land an aircraft with a powered-on gimbal on uneven terrain (such as a grass lawn or rocky surface). In such conditions there may be objects that will block the motion of the gimbal and force it into hibernation mode. Hibernation mode offers protection for the gimbal. When a camera is not mounted on the gimbal, it will default to hibernation mode. During hibernation, the gimbal does not respond to any commands from the transmitter. The gimbal resumes normal operation once a camera is mounted. The gimbal enters hibernation mode when it detects external objects blocking its range of motion. Once such objects are no longer detected, the gimbal will resume normal operation. Use of a separate battery pack to test the gimbal is suggested before powering on the flight controller, gimbal, OSD, FPV gears, etc. 18 © 2015 DJI. All Rights Reserved. Appendix Troubleshooting Problem Cause Solution 1. The transmitter trims value is 1. Adjust the transmitter trims value. 2. Connect the GCU and flight control beyond the acceptable limit. system. Gimbal keeps drifting 2. The GCU is disconnected from the 3. Ensure the gimbal is mounted so it after initialization. flight control system. is parallel with the aircraft, and the 3. The gimbal is not mounted correctly. camera is pointing towards the nose. Contact your local dealer or DJI customer service for assistance. Unable to determine BVR (beyond visual range) flight. gimbal orientation. Use a wireless video transmission module. Settings When Using the A2 Flight Control System Users should configure the H4-3D’s pitch control in the A2 assistant when using the A2 Flight Control System. Map the H4-3D to two channels on the transmitter as shown in the following diagram. DJI recommends the use of a knob switch or a stick with spring back function for tilt control, and a 2-position switch for MODE. Zenmuse Channels ROLL 0 REV Unmapped PAN 0 REV Unmapped TILT 0 REV Unmapped MODE 0 REV Unmapped SHUT 0 REV Unmapped AUX1 0 REV Unmapped AUX2 0 REV Unmapped AUX3 0 REV Unmapped © 2015 DJI. All Rights Reserved. 19 Appendix The gimbal axes are Factory calibration error. not level. Specifications General Built-in Functions Zenmuse technology 3-axis stabilized gimbal High precision brushless servo control Built-in IMU module Lightweight Phantom 2, A2, WKM, NAZA-M, NAZA-M V2, supported GoPro Hero4 Black supported Peripheral Supported Camera GoPro Hero4 Black GCU Input Power 3 S~6 S LiPo (12 V~26 V) PC Assistant System Requirement Windows XP SP3; Windows 7; Windows 8 Mechanical & Electrical Characteristics Specifications Working Current Static current: 400 mA (@12 V) Dynamic current: 600 mA (@12 V) Gimbal Input Power 3 S~6 S (12 V ~26 V) Operating Temperature -10°C ~ 50°C Gimbal Weight 168 g (camera excluded) Gimbal Dimensions (With Damping Unit) 103 mm × 92 mm × 80 mm GCU Weight 22 g GCU Dimensions 42 mm ×32 mm ×9.3 mm Working Performance Angular Vibration Range Pitch/Roll:±0.02°, Yaw: ±0.03° Maximum Controlled Rotation Speed Tilt axis: ±130°/s Controlled Rotation Range Tilt axis control: -130 ~ +45° Regulatory Approvals FCC (USA) Yes CE (EU) Yes ROHS(EU) Yes 20 © 2015 DJI. All Rights Reserved. The content is subject to change. Download the latest version from http://www.dji.com/product/zenmuse-h4-3d/download © 2015 DJI. All Rights Reserved.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project