Installation and Operation Guide
Installation and Operation Guide
Insurice PF Filter Systems
Description
Everpure Insurice PF Series Water Filter Systems (Figures 1-3) are identical to standard
Insurice systems except that the PF Series systems include a 20" sediment prefilter housing
pre-installed and assembled onto the inlet header/manifold assembly. Insurice PF systems
are designed for use in installations with dirtier, cloudier source water and incorporate the
same Everpure Insurice 1⁄2 micron Quick-Change precoat filter cartridges (I2000, I20002, I4000
& I40002) which remove potentially harmful particulates and chlorine taste and odor from the
water while introducing an advanced scale inhibitor. – As tested by Everpure
The replaceable prefilter cartridge element removes larger dirt and rust particles and extends
the life of the sub-micron carbon filters. Thus, ice quality and ice machine performance are
improved while machine downtime, maintenance and energy costs are substantially reduced.
Figure 1 – Insurice PF Single System
Selecting A Mounting Location
1.Give consideration to the weight of the unit when operating (filled with water). Operating
weights of the Insurice PF Systems are:
• Single System - 19 lbs. (8.62 kg.)
• Twin System - 35 lbs. (15.9 kg)
• Triple System - 45 lbs. (20.4 kg)
2. The location should allow for:
• Minimum clearance of 21⁄2" under the cartridge(s) so it can be lowered for removal and
replacement.
• Adequate space for “in” and “out” water line connections.
• Be near a drain for flushing.
Operating Specifications*
Combined Model Name
Insurice PF Single – i2000
Insurice PF Single – i20002
Insurice PF Twin – i2000
Insurice PF Twin – i20002
Insurice PF Triple – i2000
Insurice PF Triple – i20002
Insurice PF Single – i4000
Insurice PF Single – i40002
Insurice PF Twin – i4000
Insurice PF Twin – i40002
Insurice PF Triple – i4000
Insurice PF Triple – i40002
Replacement
Cartridge
Flow Rate
Capacity
i2000
i20002
i2000
i20002
i2000
i20002
i4000
i40002
i4000
i40002
i4000
i40002
1.67 gpm (6.3 Lpm)
1.67 gpm (6.3 Lpm)
3.3 gpm (12.6 Lpm)
3.3 gpm (12.6 Lpm)
5.0 gpm (18.9 Lpm)
5.0 gpm (18.9 Lpm)
1.67 gpm (6.3 Lpm)
1.67 gpm (6.3 Lpm)
3.3 gpm (12.6 Lpm)
3.3 gpm (12.6 Lpm)
5.0 gpm (18.9 Lpm)
5.0 gpm (18.9 Lpm)
9,000 gal (34,050 L)
9,000 gal (34,050 L)
18,000 gal (68,100 L)
18,000 gal (68,100 L)
27,000 gal (102,150 L)
27,000 gal (102,150 L)
12,000 gal (45,400 L)
12,000 gal (45,400 L)
24,000 gal (90,800 L)
24,000 gal (90,800 L)
36,000 gal (136,200 L)
36,000 gal (136,200 L)
* For individual cartridge specifications, refer to cartridge literature.
Figure 2 – Insurice PF Twin System
Figure 3 – Insurice PF Triple System
Temperature: 35-100°F (2-38°C)
Pressure:
10 - 125 psi (0.7 - 8.6 bar), non-shock
For cold water use only.
Manufactured
by Everpure
EV3119-03 Rev A MR08
Installation
14"
1. U
se the predrilled mounting holes in the manifold bracket as guides. Mark and drill anchor
holes. Mount securely. See Figures 4-6.
INLET
3/8" FNPT
2. Shut off power to ice machine.
3.Connect outlet port of Insurice PF system to equipment served. Always use a NSF approved
pipe dope or Teflon tape at all connections. Use a backup wrench on all fittings while
connecting to avoid excessive stress on the system components.
25"
4.Connect minimum 1/2" (3/4" preferred) water line to inlet side of Insurice PF system prefilter.
Do not turn on the supply water yet.
Primary
Filter
Cartridge
5 Connect tubing to flushing valve and run to drain.
Note: Some municipal plumbing codes and good sanitary practices require an air gap at
the drain termination point.
Prefilter
(Inside Sump)
6. R
emove the wrapping from the prefilter cartridge and insert it into the clear prefilter bowl,
aligning the hole in the bottom of the cartridge over the raised stub in the bottom of the
bowl.
Figure 4 – Insurice PF Single System
7. C
heck to see that the O-ring is in place at the top of the prefilter bowl and that it is
lubricated with food grade silicone lubricant. Install the bowl by aligning the hole in the
top of the cartridge with the stub extending down from the housing head and threading the
bowl onto the head. Hand tighten snugly. Do not over-tighten the bowl.
8. Remove the wrapping from the Insurice PF filter cartridge(s).
21.5"
Outlet
3/4" FNPT
INLET
3/4" FNPT
9. I nstall the Insurice PF cartridge(s) into the Insurice PF system head(s) following directions
on the cartridge label or as shown in the Cartridge Change illustrations.
10. Turn on water supply and flush the cartridge(s) by running water through at full force for
five minutes. This will set the filtering media and purge air and fines, insuring maximum
filter life.
25.59"
11. After flushing, close the flushing valve and turn on power to equipment. See illustrations.
Cartridge Change Determination
Replace cartridges when capacity is reached, or when flow becomes too slow, but at least
annually.
The system outlet pressure gauge provides a quick, simple means of determining when the
Insurice PF filter cartridge(s) should be checked. The gauge can be used to monitor dynamic
(flowing) pressure and static (line) pressure. The filter cartridges should be changed when the
gauge needle is in the red area while the system is in operation. In multiple cartridge systems,
all filter cartridges should be changed at the same time.
Figure 5 – Insurice PF Twin System
25.75"
Outlet
3/4" FNPT
INLET
3/4" FNPT
Not for residential use. For food service applications only.
29.59"
Figure 6 – Insurice PF Triple System
Cartridge Change Instructions
1. Shut off the inlet water supply to the system.
2. Make sure any outlet valves to equipment are closed.
3. Connect a drain hose to the flushing valve or place a bucket under its outlet.
4. Open the flushing valve to relieve system pressure.
5. Momentarily depress the red pressure relief valve buttons on top of the prefilter head.
6. U
nthread and remove the clear prefilter bowl and dump any water from the bowl. A sump wrench is provided to assist in loosening a tight
bowl. Remove and discard the old prefilter cartridge.
7. Rinse and clean the bowl with clean water. No special cleaners are needed.
8. Check and clean the bowl O-ring. If it is dry, lubricate it with a food grade silicone lubricant. If it is cracked or deteriorated, replace it.
9. R
emove the wrapping from a new EC210 prefilter cartridge and insert the cartridge into the prefilter bowl aligning the hole in the bottom of the
cartridge over the raised stub in the bottom of the bowl.
10. Check to see that the O-ring is in place at the top of the prefilter bowl and that it is lubricated with food grade silicone lubricant. Reinstall the
bowl by aligning the hole in the top of the cartridge with the stub extending down from the housing head and threading the bowl onto the
head. Hand tighten snugly. Do not over-tighten the bowl.
11. Remove the wrapping from the new Insurice filter cartridge(s).
12. Install the filter cartridge(s) into the filter manifold heads following directions on the cartridge label.
13. Open the inlet water supply to the prefilter sub-assembly and flush the cartridges by running water through the system at full force for five
minutes. This will purge any air and fines and ensure maximum filter life.
14. Shut off the flushing valve and open any outlet valves to equipment.
15. Restore the equipment to service.
Cartridge Change Procedure
Flushing
Everpure Carbon Filter Cartridge
Change
2. O
pen flushing valve to relieve
pressure.
4.Pull cartridge downward and
out of head.
1.Shut off power to equipment.
Shut off inlet water ahead of
system.
3.Hold head firmly and push
upward. Turn cartridge to left
until it stops.
5. H
old head firmly. Align cartridge
lug with label. Insert new
cartridge firmly into head.
6. T urn cartridge right 90˚ until
rotation stops.
7. R
epeat steps 3-6 for remaining
cartridges.
8. W
ith flushing valve fully open,
open inlet water at full force
for five minutes. Close flushing
valve.
9. Turn on power to equipment
Replacement Parts
Contact your local Everpure dealer for filter cartridges or system replacement parts.
System Tested and Certified by NSF International against NSF/
ANSI Standard 42 and 53 for the reduction of:
Std. No. 42—Aesthetic effects Std. No. 53—Health effects
Chemical Reduction
Mechanical Filtration
Taste & Odor
Turbidity (i2000, i20002 only)
Chlorine
Cyst
Mechanical Filtration
Asbestos (i2000, i20002 only)
Nominal Particulate Class I
Check for compliance with state and local laws and regulations. Do not use with water that is microbiologically unsafe or of unknown quality
without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may
contain filterable cysts.
Limited Warranty
Commercial Water Treatment Equipment
You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted
against defects in material and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period
commences from the date of purchase and is administered as follows:
For a period of ONE YEARReplaceable elements (i.e., filter & water treatment cartridges)*
For a period of FIVE YEARSThe entire system (excluding replaceable elements)
*This is for material & workmanship, not filter or water treatment cartridge life.
The unit must be used in operating conditions that conform to Everpure’s recommended design guidelines. This warranty will not apply if the unit has been
modified, repaired or altered by someone not authorized by Everpure.
If a part described above is found defective within the specified period, you should notify Everpure technical service at the phone number listed below.
Any part found defective within the terms of this warranty will be repaired or replaced (at Everpure’s discretion) by your local dealer or Everpure technical
service. You pay only freight from our factory and local dealer charges. Any repaired or replaced warranty item will be incorporated under the original
warranty terms of the existing system.
We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine,
ozone, chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or
components which do not meet Everpure’s specifications. Refer to the specifications section in the Installation and Operating manual for approved application
parameters.
Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW, EVERPURE DISCLAIMS ALL
IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT
REQUIRED BY LAW, ANY SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT
UNIT. As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing this product. The quality of
water supplies may vary seasonally or over a period of time, and your water usage rate may vary as well. Water characteristics can also differ considerably
if this product is moved to a new location. For these reasons, we assume no liability for the determination of the proper equipment necessary to meet your
requirements, and we do not authorize others to assume such obligations for us. Further, we assume no liability and extend no warranties, express or implied,
for the use of this product with a non-potable water source or a water source which does not meet the conditions for use described in the owner’s guide or
performance data sheet for this product. OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT (AT EVERPURE’S
DISCRETION) OF THE FAILED PARTS OF THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.
Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to
you. Similarly, some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local
independently operated Everpure dealer, or write Everpure for warranty and service information.
For sales, replacement components, and service, contact your Everpure dealer or:
Everpure, LLC: 1040 Muirfield Drive • Hanover Park, Illinois 60133 • 800.323.7873
In Europe: Toekomstlaan 30 • B-2200 Herentals, Belguim
In Japan: Hashimoto MN Bldg. 7F • 3-25-1 Hashimoto Sagamihara-Shi • Kanagawa 229-1103, Japan
Printed in U.S.A.
Technical Service
800.942.1153
www.everpure.com
EV3119-03 Rev A MR08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising