Operation and Safety Manual TOUCAN 861


Add to my manuals
52 Pages

advertisement

Operation and Safety Manual TOUCAN 861 | Manualzz

Operation and Safety Manual

TOUCAN 861

English - Operation and Safety Manual

31210044

07 June, 2007

FOREWORD

FOREWORD

This manual is a very important tool! Keep it with the machine at all times.

The purpose of this manual is to provide owners, users, operators, lessors, and lessees with the precautions and operating procedures essential for the safe and proper machine operation for its intended purpose.

Due to continuous product improvements, JLG Industries, Inc. reserves the right to make specification changes without prior notification. Contact JLG Industries, Inc. for updated information.

Other Publications Available:

Service and Maintenance Manual French ........................................... MA0278

Service and Maintenance Manual English .......................................... MA0280

Illustrated Parts Manual Toucan 861..................................................31210086

Hydraulic schematic.............................................................................. FL0139

Electrical schematic ..............................................................................ELE231

31210044 – JLG Lift –

a

FOREWORD

SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS

This is the Safety Alert Symbol. It is used to alert you to the potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

INDICATES AN IMMINENTLY HAZARDOUS SITUATION. IF NOT

AVOIDED, WILL RESULT IN SERIOUS INJURY OR DEATH. THIS

DECAL WILL HAVE A RED BACKGROUND.

THIS PRODUCT MUST COMPLY WITH ALL SAFETY RELATED BUL-

LETINS, CONTACT JLG INDUSTRIES, INC. OR THE LOCAL AUTHO-

RIZED JLG REPRESENTATIVE FOR INFORMATION REGARDING

SAFETY-RELATED BULLETINS WHICH MAY HAVE BEEN ISSUED

FOR THIS PRODUCT.

INDICATES A POTENTIALITY HAZARDOUS SITUATION. IF NOT

AVOIDED, COULD RESULT IN SERIOUS INJURY OR DEATH. THIS

DECAL WILL HAVE AN ORANGE BACKGROUND.

IMPORTANT

JLG INDUSTRIES, INC. SENDS SAFETY RELATED BULLETINS TO

THE OWNER OF RECORDS OF THIS MACHINE. CONTACT JLG

INDUSTRIES, INC. TO ENSURE THAT THE CURRENT OWNER

RECORDS ARE UPDATED AND ACCURATE.

INDICATES A POTENTIALITY HAZARDOUS SITUATION. IF NOT

AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY. IT MAY

ALSO ALERT AGAINST UNSAFE PRACTICES.

INDICATES PROCEDURES ESSENTIAL FOR SAFE OPERATION.

THIS DECAL WILL HAVE A YELLOW BACKGROUND.

IMPORTANT

JLG INDUSTRIES, INC. MUST BE NOTIFIED IMMEDIATELY IN ALL

INSTANCES WHERE JLG PRODUCTS HAVE BEEN INVOLVED IN

AN ACCIDENT INVOLVING BODILY INJURY OR DEATH OF PER-

SONNEL OR WHEN SUBSTANTIAL DAMAGE HAS OCCURRED TO

PERSONAL PROPERTY OR THE JLG PRODUCT.

For:

• Accident Reporting

• Product Safety Publications

• Current Owner Updates

• Questions Regarding Product Safety

CONTACT:

In USA:

JLG Industries, Inc.

Product Safety & Reliability Department,

1 JLG Drive

McConnellsburg, PA

USA 17233-9533

Toll Free: (877) 554-7233

Tel.: (717) 485-5161

Fax: (717) 485-6573

Email : [email protected]

b

• Standards and Regulations Compliance Information

• Questions Regarding Special Product Applications

• Questions Regarding Product Modifications

Outside USA:

JLG Industries,

Wright Business Centre,

1 Lonmay Road

Queenslie

Glasgow,

Scotland G33 4EL

Tel : +44(0)141 781 6700

Fax : +44(0)141 773 1907

Email : [email protected]

or Your Local JLG Office

(see adresses on manual rear cover)

– JLG Lift – 31210044

Original Issue - June 07, 2007

REVISION LOG

FOREWORD

31210044 – JLG Lift –

c

FOREWORD

d

– JLG Lift – 31210044

TABLE OF CONTENTS

SECTION - 1 - SAFETY PRECAUTIONS

1.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.2 PRE-OPERATION. . . . . . . . . . . . . . . . . . . . . 1-1

Operator Training and Knowledge. . . . . 1-1

Workplace Inspection. . . . . . . . . . . . . . . 1-1

Machine Inspection . . . . . . . . . . . . . . . . 1-1

1.3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

General . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Trip and Fall Hazards . . . . . . . . . . . . . . . 1-2

Electrocution Hazards . . . . . . . . . . . . . . 1-2

Tipping Hazards . . . . . . . . . . . . . . . . . . . 1-3

Crushing and Collision Hazards . . . . . . 1-3

1.4 TOWING, LIFTING, AND HAULING . . . . . . . 1-4

1.5 ADDITIONAL HAZARDS / SAFETY . . . . . . . 1-4

SECTION - 2 - USER RESPONSIBILITIES, MACHINE

PREPARATION, AND INSPECTION

2.1 PERSONNEL TRAINING . . . . . . . . . . . . . . . 2-1

Operator Training . . . . . . . . . . . . . . . . . . 2-1

Training Supervision. . . . . . . . . . . . . . . . 2-1

Operator Responsibility . . . . . . . . . . . . . 2-1

2.2 PREPARATION, INSPECTION, AND

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . 2-1

2.3 PRE-START INSPECTION . . . . . . . . . . . . . . 2-3

2.3.1 Walk-Around Inspection. . . . . . . . . . . . . . . . 2-4

2.3.2 Function Check . . . . . . . . . . . . . . . . . . . . . . 2-5

Control Stations . . . . . . . . . . . . . . . . . . . 2-5

Tilt Sensor Check . . . . . . . . . . . . . . . . . . 2-5

Slack / Broken Chain Sensors Check . . 2-6

SECTION - 3 - MACHINE CONTROLS AND INDICATORS

3.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 CONTROLS AND INDICATORS. . . . . . . . . . 3-1

Ground Control Station . . . . . . . . . . . . . 3-2

Manual Lowering Controls . . . . . . . . . . . 3-3

Platform Control Station . . . . . . . . . . . . . 3-4

Platform Control Indicator Console.. . . . 3-5

SECTION - 4 - MACHINE OPERATION

4.1 EMERGENCY CONTROL OPERATION . . . . 4-1

Emergency Stop Switch. . . . . . . . . . . . . 4-1

4.2 PLATFORM CONTROLS . . . . . . . . . . . . . . . 4-1

Drive Speed Selector . . . . . . . . . . . . . . . 4-1

Traveling (Driving) . . . . . . . . . . . . . . . . . 4-1

Raising And Lowering The Mast . . . . . . 4-2

Raising And Lowering The Jib . . . . . . . . 4-3

Slewing The Turntable . . . . . . . . . . . . . . 4-3

Work Platform Functions Combination . 4-3

4.3 MANUAL LOWERING CONTROLS . . . . . . . 4-3

4.4 ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Motion Alarm . . . . . . . . . . . . . . . . . . . . . 4-3

Tilt Light And Alarm . . . . . . . . . . . . . . . . 4-3

Slack/Broken Chain Light And Alarm . . 4-3

4.5 SHUT DOWN AND PARK. . . . . . . . . . . . . . . 4-4

4.6 CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

EMB-MP HAWKER Charger . . . . . . . . . . 4-5

ZIVAN High Frequency Electronic Charger 4-6

4.7 EMERGENCY TOWING. . . . . . . . . . . . . . . . 4-7

4.8 LIFTING AND TIE DOWN . . . . . . . . . . . . . . 4-7

Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Tie Down . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4.9 LOADING AND UNLOADING . . . . . . . . . . . 4-8

Using a fork lift truck . . . . . . . . . . . . . . . . 4-8

Using a winch for loading . . . . . . . . . . . . 4-8

SECTION - 5 - DECALS

SECTION - 6 - EMERGENCY PROCEDURES

6.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2 INCIDENT NOTIFICATION . . . . . . . . . . . . . 6-1

6.3 EMERGENCY OPERATION. . . . . . . . . . . . . 6-1

Operator Unable to Control Machine . . . 6-1

Platform or Mast Caught Overhead. . . . . 6-1

6.4 EMERGENCY LOWERING . . . . . . . . . . . . . 6-1

6.5 EMERGENCY TOWING PROCEDURES . . . 6-1

SECTION - 7 - INSPECTION AND REPAIR LOG

SECTION - 8 - GENERAL SPECIFICATIONS & OPERATOR

MAINTENANCE

8.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . 8-1

8.2 OPERATING SPECIFICATIONS . . . . . . . . . 8-2

Fluid Capacities . . . . . . . . . . . . . . . . . . . . 8-3

Electric power unit . . . . . . . . . . . . . . . . . . 8-3

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.3 OPERATOR MAINTENANCE. . . . . . . . . . . . 8-5

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Hydraulic filters . . . . . . . . . . . . . . . . . . . . 8-8

Turntable Lubrication. . . . . . . . . . . . . . . . 8-9

Lifting chains lubrication . . . . . . . . . . . . . 8-9

Mast Section Lubrication . . . . . . . . . . . . . 8-9

Wheel Bearing & Steering Knuckle

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Hydraulic Oil Reservoir . . . . . . . . . . . . . 8-10

Tires And Wheels. . . . . . . . . . . . . . . . . . 8-11

Verification Of The Tilt Alarm Setting. . . 8-11

31210044 – JLG Lift –

1

TABLE OF CONTENTS

2

– JLG Lift – 31210044

SECTION 1 - SAFETY PRECAUTIONS

SECTION 1. SAFETY PRECAUTIONS

1.1 GENERAL

This section outlines the necessary precautions for proper and safe machine operation and maintenance.

For proper machine use, it is mandatory that a daily routine is established based on the content of this m a n u a l . A m a i n t e na n c e p r og r a m , u s i n g t h e information provided in this manual and the Service and Maintenance Manual, must also be established by a qualified person and followed to ensure the machine is safe to operate.

If there are any questions with regard to safety, training, inspection, maintenance, application, and operation, please contact JLG Industries, Inc. (“JLG”).

FAILURE TO COMPLY WITH THE SAFETY PRECAUTIONS LISTED

IN THIS MANUAL COULD RESULT IN MACHINE DAMAGE,

PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

1.2 PRE-OPERATION

Operator Training and Knowledge

• Read and understand this manual before operating the machine.

Workplace Inspection

• The operator is to take safety measures to avoid all hazards in the work area prior to machine operation.

• Do not operate or raise the platform while on trucks, trailers, railway cars, floating vessels, scaffolds or other equipment unless approved in writing by JLG.

• Do not operate the machine in hazardous environments unless approved for that purpose by

JLG.

• Be sure that the ground conditions are able to support the maximum load of the machine.

• This machine can be operated in temperatures of

-20 o

C to 40 this range.

o

C. Consult JLG for operation outside

• This machine must be used in a sufficient ambiant light.

Machine Inspection

• Before machine operation, perform inspections and functional checks. Refer to Section 2 of this manual for detailed instructions.

• Do not operate this machine until it has been serviced and maintained according to requirements specified in the Service and Maintenance Manual.

• Be sure the footswitch and all other safety devices are operating properly. Modification of these devices is a safety violation.

• Do not operate this machine until complete training is performed by authorized persons.

• Only authorized and qualified personnel can operate the machine.

• Read, understand, and obey all DANGERS,

WARNINGS, CAUTIONS, and operating instructions on the machine and in this manual.

• Use the machine in a manner which is within the scope of its intended application set by JLG.

• All operating personnel must be familiar with the emergency controls and emergency operation of the machine as specified in this manual.

• Read, understand, and obey all applicable employer, local, and governmental regulations as they pertain to operation of the machine.

MODIFICATION OR ALTERATION OF AN AERIAL WORK

PLATFORM SHALL BE MADE ONLY WITH WRITTEN PERMISSION

FROM THE MANUFACTURER

• Do not operate any machine on which safety or instruction placards or decals are missing or illegible.

• Avoid any buildup of debris on the platform floor.

Keep mud, oil, grease, and other slippery substances from footwear and platform floor.

• Do not clean electrical components with a high pressure cleaner.

31210044 – JLG Lift –

1-1

SECTION 1 - SAFETY PRECAUTIONS

1.3 OPERATION

General

• Do not use the machine for any purpose other than positioning personnel, their tools and equipment.

• Never operate a machine that is not working properly. If a malfunction occurs, shut down the machine.

• Never slam a control switch or lever through neutral to an opposite direction. Always return lever to neutral and stop before moving the lever to the next function. Operate controls with slow and even pressure.

• Park the machine in stowed position when not in service.

• Do not allow personnel to tamper with or operate the machine from the ground with personnel in the platform, except in an emergency.

• Do not carry materials directly on platform railing unless approved by JLG.

• When two persons are in the platform, the operator shall be responsible for all machine operations.

• Always ensure that power tools are properly stowed and never left hanging by their cord from the platform work area.

• Supplies or tools which extend outside the platform are prohibited unless approved by JLG.

• When driving, always position extending structure over rear axle in line with the direction of travel.

Remember, if extending structure is over the front axle, steer and drive functions will be reversed.

• Do not assist a stuck or disabled machine by pushing, pulling, or by using extending structure functions. Only pull the unit from the towing points on the chassis.

• Do not place extending structure or platform against any structure to steady the platform or to support the structure.

• Stow extending structure and shut off all power before leaving machine.

Trip and Fall Hazards

JLG recommends that occupants of the platform wear a full body harness with a lanyard attached to an authorized lanyard anchorage point. For further information regarding fall protection requirements on

JLG products, contact JLG Industries, Inc.

• Before operating the machine, make sure all gates are closed and fastened in their proper position.

• Keep both feet firmly positioned on the platform floor at all times. Never use ladders, boxes, steps, planks, or similar items on platform to provide additional reach.

• Always enter or leave the platform using the access gate.

• Use extreme caution when entering or leaving platform. Be sure that the mast assembly is fully lowered. Face the machine, maintain “three point contact” with the machine, using two hands and one foot or two feet and one hand during entry and exit.

Electrocution Hazards

• This machine is not insulated and does not provide protection from contact or proximity to electrical current.

• Maintain safe distance from electrical lines, apparatus, or any energized (exposed or insulated) parts according to the Minimum Approach Distance

(MAD) as shown in Table 1-1, Minimum Approach

Distances (M.A.D.).

• Allow for machine movement and electrical line swaying.

1-2

– JLG Lift – 31210044

SECTION 1 - SAFETY PRECAUTIONS

Table 1-1. Minimum Approach Distances (M.A.D.)

Voltage Range

(Phase to Phase)

MINIMUM APPROACH DISTANCE in Meters

0 to 50 kV

Over 50 kV to 200 kV

Over 200 kV to 350 kV

Over 350 kV to 500 kV

6

8

3

5

Over 500 kV to 750 kV

Over 750 kV to 1000 kV

11

14

NOTE: This requirement shall apply except where employer, local or governmental regulations are more stringent.

DO NOT MANOEUVER MACHINE OR PERSONNEL INSIDE

PROHIBITED ZONE (MAD). ASSUME ALL ELECTRICAL PARTS

AND WIRING ARE ENERGIZED UNLESS KNOWN OTHERWISE.

Maintain a clearance of at least 3 m between any part of the machine and its occupants, their tools and their equipment from any electrical line or apparatus carrying up to 50 000 volts. A 0,3 m additional clearance is required for every additional 30 000 volts or less.

The minimum approach distance may be reduced if insulating barriers are installed to prevent contact and the barriers are rated for the voltage of the line being guarded. These barriers shall not be part of (or attached to) the machine. The minimum approach distance shall be reduced to a distance within the designed working dimensions or the insulating barrier.

This determination shall be made by a qualified person in accordance with employer, local or governmental requirements for work practices near energized equipment.

Tipping Hazards

• The user should be familiar with the surface before driving. Do not exceed the allowable sideslope and grade while driving.

wheels. Ensure that the driving surfaces are free of moisture, ice, grease or from any other substance that could affect wheel adhesion.

• Do not elevate platform or drive with platform elevated while on a sloping, uneven or soft surface.

• Do not raise the platform or drive from an elevated position unless the machine is on firm, level surfaces and evenly supported.

• While travelling on slopes (Refer to section 8), the platofrm MUST be fully lowered, the machine MUST travel in second gear. It is recommended to drive up the slope in FORWARD gear and to REVERSE down the slope as the machine will perform better.

• Keep the chassis of the machine at least 0,6 m from holes, bumps, drop-offs, obstructions, debris, concealed holes, and other potential hazards on the floor/surface.

• Do not push or pull any object with the extending structure.

• Never attempt to use the machine as a crane. Do not tie-off machine to any adjacent structure.

• Do not operate the machine when wind conditions exceed the rating specified on the manufacturer’s nameplate.

• Do not increase the surface area of the platform or the load. Increase of the area exposed to the wind will decrease stability.

• Do not increase the platform size with unauthorized deck extensions or attachments.

• If extending structure assembly or platform is in a position that one or more wheels are off the ground, all persons must be removed before attempting to stabilize the machine. Use appropriate equipment to stabilize machine and remove personnel.

Crushing and Collision Hazards

• Approved head gear must be worn by all operating and ground personnel.

• Check work area for clearances overhead, on sides, and bottom of platform when lifting, slewing or lowering platform, and driving.

• Never exceed the maximum platform capacity.

Distribute loads evenly on platform floor.

• Before driving on floors, bridges, trucks and other surfaces, check allowable capacity of the surfaces.

Check the ramp or slope for good adhesion of the

31210044 – JLG Lift –

• During operation, keep all body parts inside platform railing.

• Always post a lookout when driving in areas where vision is obstructed.

1-3

SECTION 1 - SAFETY PRECAUTIONS

• Keep non-operating personnel at least 1,8 m away from machine during all driving and slewing operations.

• Limit travel speed according to conditions of ground surface, congestion, visibility, slope, location of personnel, and other factors which may cause collision or injury to personnel.

• Be aware of stopping distances in all drive speeds.

When driving in high speed, slow down the machine using the drive control lever before stopping.

• Do not use high speed drive in restricted or close quarters or when driving in reverse.

• Exercise extreme caution at all times to prevent obstacles from striking or interfering with operating controls and persons in the platform.

• Be sure that operators of other overhead and floor level machines are aware of the aerial work platform’s presence. Disconnect power to overhead cranes.

• Warn personnel not to work, stand, or walk under a raised extending structure or platform. Position barricades on floor if necessary.

1.4 TOWING, LIFTING, AND HAULING

• Never allow personnel in platform while towing, lifting or hauling.

• This machine should not be towed, except in the event of emergency, malfunction, power failure, or loading/unloading. Refer to the Emergency

Procedures section of this manual for emergency towing procedures.

• Ensure extending structure is in the stowed position prior to towing, lifting or hauling. The platform must be completely empty of tools.

• When lifting machine, lift only at designated areas of the machine. Lift the unit with equipment of adequate capacity.

• Refer to the Machine Operation section of this manual for lifting information.

1.5 ADDITIONAL HAZARDS / SAFETY

• Do not use machine as a ground for welding.

• When performing welding or metal cutting operations, precautions must be taken to protect the chassis from direct exposure to weld and metal cutting spatter.

• Battery fluid is highly corrosive. Avoid contact with skin and clothing at all times.

• Charge batteries only in a well ventilated area.

1-4

– JLG Lift – 31210044

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

SECTION 2. USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

2.1 PERSONNEL TRAINING

The aerial platform is a personnel handling device; so it is necessary that it be operated and maintained only by trained personnel.

Persons under the influence of drugs or alcohol or who are subject to seizures, dizziness or loss of physical control must not operate this machine.

Operator Training

Operator training must cover:

1. Use and limitations of the controls in the platform and at the ground, emergency controls and safety systems.

2. Control labels, instructions and warnings on the machine.

3. Rules of the employer and government regulations.

4. Use of approved fall protection device.

5. Enough knowledge of the mechanical operation of the machine to recognize a malfunction or potential malfunction.

6. The safest means to operate the machine where overhead obstructions, other moving equipment and obstacles, depressions, holes, drop-offs.

7. Means to avoid the hazards of unprotected electrical conductors.

8. Specific job requirements or machine application.

Training Supervision

Training must be done under the supervision of a qualified person in an open area free of obstructions until the trainee has developed the ability to safely control and operate the machine.

Operator Responsibility

The operator must be instructed that he/she has the responsibility and authority to shut down the machine in case of a malfunction or other unsafe condition of either the machine or the job site.

2.2 PREPARATION, INSPECTION, AND

MAINTENANCE

The following table covers the periodic machine inspections and maintenance required by JLG

Industries, Inc. Consult local regulations for further requirements for aerial work platforms. The frequency of inspections and maintenance must be increased as necessary when the machine is used in a harsh or hostile environment, if the machine is used with increased frequency, or if the machine is used in a severe manner.

31210044 – JLG Lift –

2-1

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

Table 2-1.Inspection and Maintenance Table

Type Frequency

Primary

Responsibility

User or Operator

Service

Qualification

User or Operator Pre-Start Inspection

P r e - D e l i v e r y

Inspection (See

Note)

Fr e q u e n t

Inspection

(See Note)

Before using each day; or whenever there’s an Operator change.

Before each sale, lease, or rental delivery.

In service for 3 months or 150 hours, whichever comes first; or

Out of service for a period of more than 3 months; or

O w n e r, D e a l e r, o r

User Mechanic

O w n e r, D e a l e r, o r

User Mechanic

Reference

Operator and Safety Manual

Manual and applicable

JLG inspection form

Manual and applicable

JLG inspection form

Annual Machine

Inspection

(See Note)

Purchased used.

Annually, no later than 13 months from the date of prior inspection.

O w n e r, D e a l e r, o r

User Mechanic Manual and applicable

JLG inspection form

P r e v e n t a t i v e

Maintenance

At intervals as specified in the Service and

Maintenance Manual.

O w n e r, D e a l e r, o r

User Mechanic Manual

NOTE: Inspection forms are available from JLG. Use the Service and Maintenance Manual to perform inspections.

2-2

– JLG Lift – 31210044

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

2.3 PRE-START INSPECTION

The Pre-Start Inspection should include each of the following:

1. Cleanliness – Check all surfaces for leakage (oil or battery fluid) or foreign objects. Report any leakage to the proper maintenance personnel.

2. Structure Inspect the machine structure for dents, damage, weld or parent metal cracks or other discrepancies.

3. Decals and Placards – Check all for cleanliness and legibility. Make sure none of the decals and placards are missing. Make sure all illegible decals and placards are cleaned or replaced.

4. Operation and Safety Manuals – Make sure a copy of the Operator and Safety Manual, AEM

Safety Manual (ANSI markets only), and ANSI

Manual of Responsibilities (ANSI markets only) is enclosed in the weather resistant storage container.

5. “Walk-Around” Inspection – Refer to Figure 2-1.

6. Battery – Charge as required.

7. Hydraulic Oil – Check the hydraulic oil level.

Ensure hydraulic oil is added as required.

8. Accessories/Attachments - Reference the

Operator and Safety Manual of each attachment or accessory installed upon the machine for specific inspection, operation and maintenance instructions.

9. Function Check – Once the “Walk-Around”

Inspection is complete, perform a function check

(section 2.3.2) of all systems in an area free of overhead and ground level obstructions. Refer to

Section 4 for more specific operating instructions.

IF THE MACHINE DOES NOT OPERATE PROPERLY, TURN OFF

THE MACHINE IMMEDIATELY! REPORT THE PROBLEM TO THE

PROPER MAINTENANCE PERSONNEL. DO NOT OPERATE THE

MACHINE UNTIL IT IS DECLARED SAFE FOR OPERATION.

31210044 – JLG Lift –

2-3

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

Figure 2-1. Daily Walk-Around Inspection

2.3.1 Walk-Around Inspection

Begin the "Walk-Around Inspection" at Item 1, as noted on the diagram. Continue checking each item in sequence for the conditions listed in the following checklist.

6. Hand Pump - See Inspection Note.

7. All Hydraulic Cylinders - No visible damage; pivot pins and hydraulic hoses undamaged, not leaking.

8. Steering Spindles - See Inspection Note.

9. Lifting Chains, Chain Yokes and Clevis Pins -

Must be installed and in good condition. Chains must be correctly tensioned and lubricated.

TO AVOID POSSIBLE INJURY, BE SURE MACHINE POWER IS OFF.

DO NOT OPERATE MACHINE UNTIL ALL MALFUNCTIONS HAVE

BEEN CORRECTED.

INSPECTION NOTE: On all components, make sure

there are no loose or missing parts, that they are securely fastened, and no visible damage, leaks or excessive wear exists in addition to any other criteria mentioned.

1. Platform Guardrails and Gate - Footswitch works properly, not modified, disabled or blocked. The gate opens and closes properly.

2. Platform & Ground Control Consoles - Control levers return to neutral, decals/placards secure and legible, control markings legible.

3. Wheel/Tire Assemblies - Properly secured, no missing lug nuts.

4. Drive Motor, Brake - No evidence of leakage.

5. Hood Assemblies - See Inspection Note.

2-4

– JLG Lift – 31210044

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

2.3.2 Function Check

Refer to section 3 & 4 for description and operation of machine functions.

Tilt Sensor Check

DO NOT OPERATE MACHINE UNTIL ALL MALFUNCTIONS HAVE

BEEN CORRECTED.

Perform the Function Check as follows:

Control Stations

1. From the Ground Control Console :

• Energize the machine.

2. From the Platform Control Console :

• Ensure that the platform control console is firmly secured;

• Ensure proper operation of horn;

• Ensure proper operation of all functions;

• Ensure that all machine functions are disabled when the Emergency Stop Button is pushed in;

• Ensure that no functions can be operated unless the footswitch is depressed;

• Activate simultaneously a drive movement and superstructure movement. Only the drive movement shall occur.

• Drive the machine on a grade, not to exceed the rated gradeability and stop to ensure the brakes hold.

Check the tilt sensor, located on the right side of the chassis, to ensure proper operation. Wedge a block

(P/N : ST2741, located in the manual storage container) as illustrated above to activate the tilt sensor and keep it tilted. Raise the mast by approximately 1m.

The system is functioning properly if :

1. From the Platform Control Console :

• An acoustic alarm sounds.

• The red tilt indicator lights up on the Platform.

• No movement is possible.

• Depress the reset button :

- All the movements are possible at normal speed to clear from the tilted situation.

31210044 – JLG Lift –

2-5

SECTION 2 - USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION

Slack / Broken Chain Sensors Check

Check the slack/broken chain sensors to ensure proper operation :

4 sensors.

Location : 2 at the top of mast #1 and 2 at the bottom of mast #4.

NOTE: The mast #1 is attached to the turntable and mast

#4 supports the jib.

Wedge a block (P/N : ST2741) as illustrated above to activate the slack chain sensor and keep it activated.

The system is functioning properly if :

1. From the Platform Control Console :

• An acoustic alarm sounds.

• The red slack chain indicator lights up on the

Platform Control console.

• The jib and mast lowering functions are disabled.

• All other functions work normally.

2. From the Ground Control Console :

• An acoustic alarm sounds.

3. Repeat steps 1 to 2 for each slack chain sensor.

2-6

– JLG Lift – 31210044

SECTION 3 - MACHINE CONTROLS AND INDICATORS

SECTION 3. MACHINE CONTROLS AND INDICATORS

1. Driving wheels

2. Steering wheels

3. Counterweight

4. Jib

5. Ground control station

6. Charger

7. Telescopic mast

8. Hand pump

9. Platform

10. Platform control station

11. Manual storage container

12. Battery cover

13. Manual lowering controls

14. Chassis cover

15. Circuit-breaker

Figure 3-1. Basic Nomenclature

3.1 GENERAL

IMPORTANT

T H E M A N U FA C T U R E R H A S N O D I R E C T C O N T R O L O V E R

MACHINE APPLICATION AND OPERATION. THE USER AND

OPERATOR ARE RESPONSIBLE FOR CONFORMING WITH GOOD

SAFETY PRACTICES.

This section provides the necessary information needed to understand control functions.

3.2 CONTROLS AND INDICATORS

TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY

CONTROL LEVERS OR TOGGLE SWITCHES CONTROLLING

PLATFORM MOVEMENT DO NOT RETURN TO THE OFF POSITION

WHEN RELEASED.

31210044 – JLG Lift –

3-1

SECTION 3 - MACHINE CONTROLS AND INDICATORS

Ground Control Station

1. Emergency Stop Switch

2. Ignition Key

3. Circuit -Breaker

4. Battery Filling Pump Switch

5. Main Circuit Breaker

Figure 3-2. Ground Control Station

1. Emergency Stop Switch

Depress the switch to stop all functions. The switch must be turned clockwise to restore the machine’s function.

2. Ignition Key

Position the key to "I" to start the machine, or to "O" to remove the electrical power and remove the key.

3. Circuit-Breaker

Protection of the control circuit.

3-2

4. Battery Filling Pump Switch

Toggle the pump switch to fill the battery.

(See Maintenance section for further instructions).

5. Main Circuit breaker

Push the circuit breaker knob to insulate the battery.

Pull the circuit breaker to restore the battery supply.

– JLG Lift – 31210044

Manual Lowering Controls

SECTION 3 - MACHINE CONTROLS AND INDICATORS

Electro-Hydraulic Control Valve With Manual Control Push Buttons

1. Mast Raising / Lowering Control valve :

Lift the mast function control lever while activating the hand pump to raise the mast.

Lower the mast function control lever while activating the hand pump to lower the mast.

2. Jib Raising / Lowering Control Valve :

Lift the jib function control lever while activating the hand pump to raise the jib.

Lower the jib function control lever while activating the hand pump to lower the jib.

3. Slewing Control Valve :

Lift the slewing control lever while activating the hand pump to slew the turntable to the right.

Lower the slewing control lever while activating the hand pump to slew the turntable to the left.

4. Pump Handle :

Insert the pump handle in the hand pump to operate it.

5. Hand Pump :

Operate the hand pump while activating the desired movement.

1.Mast Raising / Lowering Control Valve

2.Jib Raising / Lowering Control Valve

3.Slewing Control Valve

4.Pump Handle

5.Hand Pump

Figure 3-3. Manual Lowering Controls

31210044 – JLG Lift –

3-3

SECTION 3 - MACHINE CONTROLS AND INDICATORS

Platform Control Station

(See Figure 3-5., Platform Control Indicator console)

1. Footswitch

Must be depressed before any movement is controlled. The control can be actuated if the green indicator is lit.

2. Turntable Slewing Control Lever

Tilt the lever to the right to slew the turntable to the right.

Tilt the lever to the left to slew the turntable to the left.

3. Jib Function Control Lever

Lift the lever to raise the jib.

Lower the lever to lower the jib.

4. Mast Function Control Lever

Lift the lever to raise the mast.

Lower the lever to lower the mast.

5. Drive Control Lever

Push the lever to drive forward.

Pull the lever to reverse.

6. Steering Control Lever

Tilt the lever to the right to steer the wheels to the right.

Tilt the lever to the left to steer the wheels to the left.

3-4

– JLG Lift –

Figure 3-4. Platform Control Console

1. Footswitch

2. Turntable Slewing Control Lever

3. Jib Function Control Lever

4. Mast Function Control Lever

5. Drive Control Lever

6. Steering Control Lever

7. Platform Control Indicator console

31210044

Platform Control Indicator Console

.

SECTION 3 - MACHINE CONTROLS AND INDICATORS

1. Emergency Stop Switch

2. Drive Speed Selector

3. Push Button (3 Functions)

4. Power Enable Indicator

5. Drive Speed Limitation Indicator

6. Slack/Broken Chain Indicator Light and Alarm

7. Tilt Indicator Light and Alarm

8. Battery Discharge Indicator

Figure 3-5. Platform Control Indicator console

1. Emergency Stop Switch

Depress the switch to stop all the functions of the machine. The switch must be turned clockwise to restore the machine’s functions.

2. Drive Speed Selector

1st gear or slow speed

2nd gear or climbing speed (max. 15% grade)

3rd gear or high speed

3. Push Button (3 Functions)

- Horn

- Reset Button : this button can be pressed to use the remaining battery charge to travel to the charging station.

- Reset Button : this button can be pressed to lower the platform once the maximum tilt has been reached.

NOTE: The button must be actuated and held BEFORE the

footswitch is depressed.

4. Power Enable Indicator

Green light indicates that the controls are ready.

5. Drive Speed Limitation Indicator

Orange light indicates the machine is in a configuration where the drive speed is limited to

2nd gear.

6. Slack/Broken Chain Indicator Light and Alarm

Slack lifting chain. Red light and audible alarm indicate slack chain condition has been detected.

31210044 – JLG Lift –

7. Tilt Indicator Light and Alarm

Excessive tilt. Red light and audible alarm indicate the rated slope has been exceeded.

8. Battery Discharge Indicator/Hourmeter

As the battery discharges, the bar lit in (1) moves from the right to the left (5 green bars followed by

3 orange bars).

At this point, the LED flashes indicating "energy reserve" (70% discharged).

The 2 red LEDs most to the left flash indicating

"empty" (80% discharged). At this point, power is cut-off. The battery must be recharged.

1 - Discharge Indicator

2 - Hourmeter

3-5

SECTION 3 - MACHINE CONTROLS AND INDICATORS

This page has been intentionally left blank.

3-6

– JLG Lift – 31210044

SECTION 4 - MACHINE OPERATION

SECTION 4. MACHINE OPERATION

NOTE: A delay-timer, integrated to the electrical system,

disconnects the control consoles approximately 4 hours after the last operation of the machine. This system preserves the battery should the operator forget to disconnect the machine. After cut out, the emergency stop switch on the ground control console must be depressed then turned clockwise to restore the functions of the machine.

- release and activate the enable control again and control the movement again.

- position the drive speed selector to 2

nd

gear

( ) and return it to 3

rd

gear ( ).

• To energize the machine :

Pull the knob of the circuit-breaker to "I" position.

DO NOT DRIVE WITH MAST OUT OF TRANSPORT MODE EXCEPT

ON A SMOOTH, FIRM AND LEVEL SURFACE.

TO AVOID LOSS OF TRAVEL CONTROL OR “TIP OVER”, DO NOT

DRIVE MACHINE ON GRADES EXCEEDING THOSE SPECIFIED IN

SECTION 8.2 OF THIS MANUAL.

USE EXTREME CAUTION WHEN DRIVING IN REVERSE AND AT

ALL TIMES WHEN THE PLATFORM IS ELEVATED.

THE ARROWS ON THE CHASSIS COVERS INDICATE THE

CORRECT DIRECTION OF TRAVEL OF THE MACHINE.

4.1

EMERGENCY CONTROL OPERATION

Emergency Stop Switch

This switch, when in the on (out) position, provides electrical power to the platform controls. In addition, the switch can be used to turn off power (push the switch IN) to the function controls in the event of an emergency.

4.2

PLATFORM CONTROLS

NOTE: The speed of any movement is proportional to the

course of the appropriate lever : the more the lever is pushed (or pulled), the faster is the movement.

Drive Speed Selector

The DRIVE SPEED selector can be positioned either to

3rd gear ( ), 2nd gear ( ) or 1st ( ) position and that speed will be obtained. When the mast is raised, the high speed drive (TORQUE or HIGH position) is cutout and only the low drive speed is attainable.

Traveling (Driving)

See Figure 4-1., Grade and Side Slope

NOTE: Refer to the General Specifications (Section 8) for

Gradeability and Side slope ratings.

All ratings for Gradeability and Side slope are based upon the machine in transport mode with the mast and jib being in the stowed position, fully lowered, and retracted.

With the machine in transport mode, traveling is limited by two factors, gradeability and si de slope.

Gradeability is the percent of grade of the incline the machine can climb. Sideslope, is the angle of the slope the machine can be driven across. Reference section 8 for gradeability and side slope ratings.

When the mast is extended, the machine must not be operated on grades or side slopes that are greater than that specified in Section 8. The tilt alarm will sound and tilt indicator will light to alert the operator when the machine has exceeded the rated slope. All the movements are cut and the reset button must be depressed to return the platform to a more stable position.

NOTE: When the platform is driven in 3 rd

gear on a slope steeper than 5%, the machine switches automatically to 2

nd

gear. The 3

rd

gear will be restored only when the platform is driven on a slope below 5%.

Either of the following actions must be done :

31210044 – JLG Lift –

4 -1

SECTION 4 - MACHINE OPERATION

Figure 4-1. Grade and Side Slope

Forward

1. Position the DRIVE SPEED selector to 1st gear

( ), 2nd gear ( ) or 3rd gear ( ).

2. Depress footswitch.

3. Push the lever forward.

Stopping

Stopping is accomplished by slowly returning the

DRIVE lever to the neutral position. The brakes will apply automatically.

Reverse

Traveling in reverse is accomplished the same way as traveling forward except for pulling the DRIVE lever toward the operator.

Steering

Steering is accomplished by tilting the lever to the right to steer the wheels to the right or to the left to steer the wheels to the left.

TO AVOID TIP OVER, LOWER PLATFORM TO GROUND LEVEL.

THEN DRIVE MACHINE TO A LEVEL SURFACE BEFORE RAISING

MAST.

TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY

CONTROL LEVER CONTROLLING PLATFORM MOVEMENT DOES

NOT RETURN TO THE ’OFF’ OR NEUTRAL POSITION WHEN

RELEASED.

IF THE PLATFORM DOES NOT STOP WHEN A LEVER IS

RELEASED, REMOVE FOOT FROM FOOTSWITCH OR USE

EMERGENCY STOP SWITCH TO STOP THE MACHINE.

Raising And Lowering The Mast

Raising the mast :

1. Depress footswitch.

2. Lift the mast control lever to raise the mast.

Lowering the mast :

1. Depress footswitch.

2. Lower the mast control lever to lower the mast.

4-2

– JLG Lift – 31210044

SECTION 4 - MACHINE OPERATION

Raising And Lowering The Jib

Raising the jib :

1. Depress footswitch.

2. Lift the jib control lever to raise the jib.

Lowering the jib :

1. Depress footswitch.

2. Lower the jib control lever to lower the jib.

Slewing The Turntable

To slew :

1. Depress footswitch.

2. Tilt the turntable slewing control lever to the right to slew the turntable to the right. Tilt the turntable slewing control lever to the left to slew the turntable to the left.

Work Platform Functions Combination

A drive movement cannot be combined with a structure movement.

If a structure and drive movements are actuated together, only the drive movement will be performed.

4.3

MANUAL LOWERING CONTROLS

The manual lowering controls should be used in emergency situations or electrical breakdown. The manual lowering controls provide an auxiliary means of lowering and raising the platform and slewing the turntable in the event of primary power loss.

4.4

ALARMS

Horn

Horn is activated when the corresponding push button located on the Platform Control Console is depressed.

Motion Alarm

The machine is fitted with 2 lights (beacons) that come on as soon as the enable pedal is depressed or a lowering function is controlled.

Tilt Light And Alarm

The alarm is triggered by a tilt sensor located on the right hand side of the chassis under the chassis cover.

This alarm is active once the chassis is 2° off the horizontal. It consists of a light on the platform control console and an alarm. The alarm and light indicate that the work platform is at its maximum out of level limit

(refer Table 8.1) and is nearing an unstable position. All the functions are disabled. The reset button must be used to return the platform to a more stable position.

When the tilt light or alarm is activated, it is recommended to place the machine in the following configuration :

1. Mast lowered.

2. Jib in line with the chassis length.

3. Jib lowered ONLY if it is positioned below the maximum outreach.

DO NOT RAISE MAST OR OPERATE JIB WITH MAST RAISED

WHEN MACHINE IS OUT OF LEVEL.

Slack/Broken Chain Light And Alarm

The slack chain detection system prevents movements if the platform or the jib come to rest on an obstacle while lowering the mast or the jib.

When a slack chain is detected, the sensor actuates an acoustic alarm and a red light is lit on the platform control console. The mast and jib lowering movements are disabled.

Procedure to follow in case this feature is activated :

1. Raise the mast or the jib (generally the reverse movements to the one that caused the alarm to sound).

2. Identify the cause.

3. Perform the movement which will clear the machine and prevent contact with the obstacle.

If the examination of the surroundings does not reveal any possible obstacle, the alarm may have been triggered by the telescopic mast jamming which could be due to :

• A foreign body entering the guiding system.

• A lack of lubrication.

• Incorrect operation.

31210044 – JLG Lift –

4 -3

SECTION 4 - MACHINE OPERATION

IF THE SLACK CHAIN ALARM HAS BEEN TRIGGERED BY MAST

JAMMING, DISCONTINUE OPERATION IMMEDIATELY. DO NOT

USE THE MANUAL LOWERING CONTROLS. PLATFORM

OCCUPANTS MUST BE RESCUED AND THE MACHINE SERVICED

BY A QUALIFIED TECHNICIAN.

4.5

SHUT DOWN AND PARK

To shut down and park the machine, the procedures are as follow :

1. Drive machine to a reasonably well protected area.

2. Ensure mast is lowered and jib stowed.

3. Push in the Emergency Stop at Platform Control

Station.

4. At Ground Control Station, push in the Emergency

Stop, position the ignition key to "O" and remove the key.

5. Depress the circuit breaker push button.

6. If necessary, cover Platform Controls to protect instruction placards, warning decals and operating controls from hostile environment.

7. Charge the batteries if the LEDs on the discharge indicator are orange or red.

4.6

CHARGER

The work platform on-board electronic charger is designed to automatically charge 24 V DC lead-acid rechargeable batteries.

Several types of chargers can be fitted on the machine depending on the capacity of the battery.

The covers of the machine must be open during battery charge.

LEAD-ACID BATTERIES MAY EMIT HIGHLY EXPLOSIVE GASES.

THE EMISSION IS GREATLY INCREASED DURING CHARGING.

NEVER INTRODUCE FLAMES, SPARKS OR OTHER SOURCES OF

IGNITION TO BATTERY AREA. FAILURE TO COMPLY WITH THIS

WARNING COULD RESULT IN DEATH OR INJURY TO

PERSONNEL. ALWAYS CHARGE BATTERIES IN A WELL-

VENTILATED AREA.

DO NOT DISCONNECT BATTERY PLUG WHEN THE CHARGER IS

ON. THE RESULTING ARCING COULD CAUSE BATTERY TO

EXPLODE AND BURNS TO THE OPERATOR.

NOTE: It is not necessary to charge the battery if the

electrolyte specific gravity has not dropped under

1.240 kg/l. Regular charge of a battery when its specific gravity is higher then 1.240 kg/l can greatly reduce the battery life.

NOTE: The charger has an interlock feature which causes

the work platform power circuit to open anytime the charger is plugged into a live AC outlet.

NOTE: If power supply is stopped during the charge cycle,

the charger switches to a waiting mode and restarts automatically as soon as the power returns.

Supply Voltage :

Always ensure the voltage selected corresponds to the network voltage and the socket protection is sufficient to support the charger power.

Incorrect setting of the charger voltage may result in malfunction or breakdown.

The chargers are factory preset based upon the plug type fitted.

4-4

– JLG Lift – 31210044

SECTION 4 - MACHINE OPERATION

EMB-MP HAWKER Charger

a. Charge indicator (green)

b. Final charge indicator (yellow)

c. Battery indicator charge completed (green)

d. Fault indicator (red)

e. Circuit breaker

Charging the battery :

- Plug the charger into the mains (single phase 2 poles + ground).

- Once the charger is connected, all the leds begin to flash for a short period of time, indicating the charger is completing a self-test.

- The leds (c) and (d) will then flash for a short period of time, indicating the charger is in "automatic starting" mode.

- The charging phase starts, the green led (a) flashes slowly (frequency = 1 Hz) during the duration of the charge.

- Once the final charging phase has been reached

(approximately 80%), led (a) still flashes and led (b) lights up fixed.

- At the end of the charging process, both leds (a) and (c) are on fixed.

Equalization charge :

- When the charger is doing an equalization charge :

• both leds (a) and (c) flash slowly.

• Led (b) is lit fixed.

Fault indicator :

- Should the transformer overheat, the red led (d) flashes quickly (Frequency = 5 Hz).

- If the battery does not reach 2.4 V/cell after a 10 hour charge, the charging process stops and the red led (d) lights up.

It is advisable to have either the charger or the battery checked by a technician.

Leds signal :

Signal

Self-test (few seconds)

Automatic starting mode (few seconds)

Initial charge

Final charge

Charge completed or equalization pause

Equalization charge

Default (safety temporisation)

Default (thermal protection on transformer))

a green b yellow c green

BL BL

OFF OFF

BL

BL

BL

BL

ON

BL

ON

*

OFF OFF OFF

ON OFF OFF

* ON OFF

ON

*

*

BL

OFF

*

OFF

ON

BV

d red

BL

BL

OFF = the led is off

ON = the led is lit fixed

BL = the led flashes (T=1 Hz)

BV = the led flashes quickly (T = 5 Hz)

* = the led can be on or off, depending on the state of charge of the battery and on the charger’s operation at that moment.

31210044 – JLG Lift –

4 -5

SECTION 4 - MACHINE OPERATION

ZIVAN High Frequency Electronic Charger

Charging the battery :

- Plug the charger into the mains (single phase 230

VAC 2 poles + ground).

- The charger starts automatically.

Charging phase indicator on the charger :

Red LED : The charger is in the charge initial phase

(phase 1).

Flashing Red LED : The charger is in a constant tension phase (phase 2).

Yellow LED : The battery is

80% charged.

Green LED : The battery is

100% charged.

Alarms :

A flashing LED and an intermittent acoustic alarm indicate a faulty situation. When the alarm is on, the charger no longer delivers any current.

Leds signal :

CONDITION

ALARM

TYPE

RED

GREEN

Batteries presence

Timeout

RED /

YELLOW

RED /

GREEN

YELLOW /

GREEN

RED /

YELLOW /

GREEN

Battery current

Battery voltage

Selection

Thermal safety

DESCRIPTION (Action)

Battery disconnected or not in conformity.

(Verify the connection and the nominal voltage).

Phase 1 and/or Phase 2 have a duration in excess of the maximal allowed.

(Verify the battery capacity).

Loss of output Current control.

(Failure of the control logic).

Loss of output Voltage control.

(Battey disconnected or failure of the control logic).

An unavailable configuration has been selected.

(Verify the selector's position).

Overheating of semiconductors.

(Check for proper operation of the fan).

4-6

– JLG Lift – 31210044

SECTION 4 - MACHINE OPERATION

4.7

EMERGENCY TOWING

Towing is discouraged and must only be performed as a last option.

IMPORTANT

VERIFY THE CAPACITY OF THE EQUIPMENT USED TO TOW THE

MACHINE.

ENSURE THE MACHINE IS ON LEVEL GROUND BEFORE

RELEASING THE BRAKES.

THE MACHINE MUST ALWAYS BE IN STOWED POSITION DURING

TOWING PROCEDURE.

NO PERSONNEL IS ALLOWED ON THE PLATFORM DURING

TOWING PROCEDURE.

To tow, release the brakes and the wheel motors as follow:

1. Fully lower the platform.

2. Remove the pump handle from its support.

3. Before releasing the valve, wait 30 seconds after the end of a drive movement.

4. Pull the lever of the brake release valve (located at the rear side of the chassis) to "BRAKE

UNLOCKED" position ( ).

5. Insert the handle in the hand pump.

6. Activate the hand pump until the movement gets harder.

7. Use a winch to tow the machine (if a winch is not available, use another low speed towing device).

IMPORTANT

WHEN TRANSPORTING THE MACHINE, THE MACHINE MUST BE

STOWED.

Lifting

1. The weight of the machine is stamped on the serial number plate (See § 8.2). If the plate is missing or illegible, call JLG Industries or weigh the individual unit to find out the Gross Vehicle

Weight.

2. Place the machine in the stowed position.

3. Remove all loose items from the machine.

4. Attach lifting device and equipment only to the designated lifting points. (See below).

THERE IS ONE TIE DOWN/EMERGENCY TOW LUG INSTALLED

ON EACH END OF THE CHASSIS OF THE WORK PLATFORM.

8. At the end of the procedure, return the release valve to NORMAL USE ( ). The machine and the brakes are operational.

MACHINE HAS NO TOWING BRAKES. TOWING VEHICLE MUST

BE ABLE TO CONTROL MACHINE AT ALL TIMES, ON-HIGHWAY

TOWING NOT PERMITTED, FAILURE TO FOLLOW INSTRUCTIONS

COULD CAUSE SERIOUS INJURY OR DEATH. MAXIMUM TOWING

GRADE 20%.

USE BOTH RINGS TO LIFT THE MACHINE.

5. Properly adjust the rigging to prevent damage to the machine.

BEFORE TOWING, THE BRAKES AND THE WHEEL MOTORS

MUST BE RELEASED. TOWING IS LIMITED TO EXTREMELY

SHORT DISTANCES AT A MAXIMUM SPEED OF 1 KM/H. SEVERE

DAMAGE TO THE DRIVE SYSTEM MAY RESULT IF TOWING IS

OTHERWISE ACCOMPLISHED.

4.8

LIFTING AND TIE DOWN

31210044 – JLG Lift –

4 -7

SECTION 4 - MACHINE OPERATION

Tie Down

1. Place the machine in the stowed position.

2. Remove all loose items from the machine.

3. Chock wheels in both directions.

4. Secure the chassis using straps or chains of adequate strength and attached to the designated tie down points.

4.9

LOADING AND UNLOADING

Using a fork lift truck

4-8

This page has been intentionally left blank.

Figure 4-2. Position of the forks

VERIFY THE CAPACITY OF THE FORKLIFT TRUCK AND OF ITS

EQUIPMENT. FORK LIFT ONLY AT THE DESIGNATED POINTS. ANY

OTHER POSITION OF THE FORKS WILL CAUSE THE MACHINE TO

TIP OVER. NOBODY MUST BE ON THE PLATFORM OF THE

MACHINE DURING LOADING AND UNLOADING OPERATIONS.

THE WORK PLATFORM MUST BE KEPT AS NEAR TO THE

GROUND AS POSSIBLE DURING FORK LIFT OPERATION.

Using a winch for loading

If the work platform cannot be loaded safely using the work platform controls, use a winch (release brakes prior to the operation).

CHECK THE CAPACITY OF THE EQUIPMENT USED. PLACE THE

MACHINE IN TOWING MODE (SEE § 4.7) FOR THE LOADING AND

UNLOADING PROCEDURES. NOBODY MUST BE IN THE

PLATFORM DURING THIS OPERATION.

– JLG Lift – 31210044

SECTION 5. DECALS

SECTION 5 - DECALS

Small basket

Instructions AU 1434

Loads AU 1435

Large basket

Instructions

Loads

AU 1434

AU 1436

31210044 – JLG Lift –

5-1

SECTION 5 - DECALS

5-2

– JLG Lift – 31210044

SECTION 6 - EMERGENCY PROCEDURES

SECTION 6. EMERGENCY PROCEDURES

6.1 GENERAL

This section explains the steps to be taken in case of an emergency situation while operating.

6.2 INCIDENT NOTIFICATION

JLG Industries, Inc. must be notified immediately of any incident involving a JLG product. Even if no injury or property damage is evident, the factory should be contacted by telephone and provided with all necessary details.

In USA : 877-JLG-SAFE (Toll free)

Outside USA: 717-485-5161

E-mail:[email protected]

Failure to notify the manufacturer of an incident involving a JLG Industries product within 48 hours of s u c h a n o c c u r r e n c e m a y v o i d a n y w a r r a n t y consideration on that particular machine.

6.4 EMERGENCY LOWERING

If primary power is lost, the platform may be lowered manually. Reference section 3 for Manual Lowering

Control procedures.

6.5 EMERGENCY TOWING PROCEDURES

Towing this machine is discouraged. However, provisions for towing the machine in emergency situations have been incorporated. For specific procedures, refer to Section 4.

IMPORTANT

FOLLOWING ANY ACCIDENT, THOROUGHLY INSPECT THE

MACHINE AND TEST ALL FUNCTIONS FIRST FROM THE GROUND

CONTROLS, THEN FROM THE PLATFORM CONTROLS. DO NOT

LIFT ABOVE 3 M UNTIL YOU ARE SURE THAT ALL DAMAGE HAS

BEEN REPAIRED, IF REQUIRED, AND THAT ALL CONTROLS ARE

OPERATING CORRECTLY.

6.3 EMERGENCY OPERATION

Operator Unable to Control Machine

IF THE PLATFORM OPERATOR IS PINNED, TRAPPED

OR UNABLE TO OPERATE OR CONTROL MACHINE:

1. Other personnel should operate the machine from ground controls only as required.

2. Other qualified personnel on the platform may use the platform controls. DO NOT CONTINUE

OPERATION IF CONTROLS DO NOT FUNCTION

PROPERLY.

3. Appropriate equipment can be used to remove platform occupants and stabilize motion of the machine.

Platform or Mast Caught Overhead

If the platform or mast becomes jammed or snagged in overhead structures or equipment, rescue platform occupants prior to freeing the machine.

31210044 – JLG Lift –

6-1

SECTION 6 - EMERGENCY PROCEDURES

This page has been intentionally left blank.

6-2

– JLG Lift – 31210044

SECTION 7 - INSPECTION AND REPAIR LOG

SECTION 7. INSPECTION AND REPAIR LOG

Type of machine :_______________________________________ Machine Serial Number :__________________________________

Table 7-1. Inspection and Repair Log

Date Comments

Name :______________________________________

Signature :____________________________________

31210044 – JLG Lift –

7-1

SECTION 7 - INSPECTION AND REPAIR LOG

This page has been intentionally left blank.

7-2

– JLG Lift – 31210044

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

SECTION 8. GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

8.1 INTRODUCTION

This section of the manual provides additional necessary information to the operator for proper operation and maintenance of this machine.

The maintenance portion of this section is intended as information to assist the machine operator to perform daily maintenance tasks only, and does not replace the more thorough Preventive Maintenance and Inspection

Schedule included in the Service and Maintenance

Manual.

Other Publications Available :

Service and Maintenance Manual French........ MA0278

Service and Maintenance Manual English ....... MA0280

Illustrated Parts Manual ..................................31210086

Hydraulic schematic ...........................................FL0139

Electrical schematic........................................... ELE231

31210044 – JLG Lift –

8-1

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

8.2 OPERATING SPECIFICATIONS

Platform Size

Maximum Work Load

Slewing

Max. Platform Height

Horizontal Reach

(from centerline of machine)

(from rear wheel edge)

(from side wheel edge)

Up and Over Clearance

Max. Hydraulic System Pressure

Maximum Operating Wind Speed

Maximum Horizontal Manual Force

Vibration levels

Acoustic pressure

Table 8-1. Operating Specifications And Dimensions

TOUCAN 861

700 x 900 mm

220 kg (2 persons + 60 kg material)

900 x 1010 mm

200 kg (2 persons + 40 kg material)

180°

6.72 m

Electrical System Voltage

Gross Machine Weight

(Platform Empty)

Overall Length

Overall Height

Overall Width

Maximum Wheel Load

Maximum Travel Grade (Gradeability)

With mast in stowed position and jib below horizontal

Maximum Travel Grade (Side slope)

With mast in stowed position and jib below horizontal

Tilt Sensor Setting

Turning Radius

Inside :

Outside :

2.64 m

1.84 m

2.15 m

2.68 m

5.42 m

23 MPa

45 km/h (12.5 m/s)

400 N

24V

2980 kg

1.99 m

0.99 m

1950 kg

15% (8.5°)

2.96 m

2.15 m

2.46 m

2.99 m

1.02 m

2.40 m

The weighed root mean square acceleration value to which the arms are subjected

(control levers) is inferior to 2,5m/s/s.

The weighed root mean square acceleration value to which the feet are subjected (platform floor) is inferior to 0,5m/s/s/.

The equivalent continuous ’A’ weighed sound pressure level at the work station is <to

70 dB(A).

The measure has been taken by placing the sonometer at 1,60m above the platform floor.

8-2

– JLG Lift – 31210044

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

Fluid Capacities

Main Hydraulic Tank

Table 8-2. Capacities

20.5 l

Electric power unit

Table 8-3. Electric Power Unit Specifications

Main

Power

Unit

Motor

Pump

Maximum 24 MPa

Power

Voltage

Flow Rate

Displacement

3 kW

24 VDC

9.5 l/mn at 15 MPa

5.5 cm³/t

Batteries

Table 8-4. Battery Specifications

Voltage

Amp Hour Rating

Life Cycle Rating

24 Volt

620 Ah (5h rate)

1200 Cycles

31210044 – JLG Lift –

8-3

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

1- Batteries

2- Hydraulic Filters

3- Turntable Lubrication

4- Lifting Chains Lubrication

5- Mast Section Lubrication

Figure 8-1. Operator Maintenance & Lubrication Diagram

6- Wheel Bearing & Steering Knuckles Lubrication

7- Hydraulic Oil Reservoir

8- Tires & Wheels

9- Verification of the Tilt Alarm Setting

8-4

– JLG Lift – 31210044

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

8.3 OPERATOR MAINTENANCE

1. Batteries

• Fill the can with distilled water.

DRAINED WATER MAY HAVE BEEN IN CONTACT WITH ACID AND

MAY HAVE BECOME CORROSIVE. DO NOT ALLOW DRAIN

WATER TO CONTACT THE SKIN OR EYES. IF IT OCCURS, FLUSH

THE CONTACTED AREA WITH WATER AND CONSULT A DOCTOR

IMMEDIATELY. APPROPRIATE EQUIPMENT MUST BE WORN

(GLOVES, GOGGLES, RUBBER APRON) TO PREVENT THE

DRAINED WATER FROM CONTACTING THE SKIN OR ANY PART

OF THE BODY.

BATTERY ELECTROLYTE MUST NOT BE ALLOWED TO CONTACT

THE SKIN OR EYES. IF IT DOES OCCUR, FLUSH THE

CONTACTED AREA WITH WATER AND CONSULT A DOCTOR

IMMEDIATELY. APPROPRIATE EQUIPMENT MUST BE WORN

(GLOVES, GOGGLES, RUBBER APRON) TO PREVENT THE

ELECTROLYTE FROM CONTACTING THE SKIN OR ANY OTHER

PART OF THE BODY DURING ANY SERVICING OPERATION ON

THE BATTERY.

• Depress and hold the push button to activate the battery filling pump until the flow indicator slows down.

DURING MAINTENANCE OR ANY SERVICING OPERATION ON

THE BATTERY, RINGS, WATCHES OR ANY OTHER JEWELLERY

MUST BE REMOVED.

Daily maintenance

Electrolyte level

Verify the electrolyte level after the charge using the floats in the center of each filling cap.

• Check that the level is correct in each battery cell.

Weekly maintenance

Cleaning - Battery maintenance

It is necessary to clean the battery regularly to prevent salt formation and current arcing which could damage the machine.

• Clean and dry the battery top.

• Ensure the connections are clean and tight.

• Keep the metallic containers clean. In case of corrosion, clean, neutralize corrosion and apply anti-acid paint on the affected area.

• Drain the water that can accumulate at the bottom of the container (electrolyte overflow, leak in the centralized filling circuit, battery cleaning...).

To drain the water :

NOTE: Tilt the charger to gain access to the front battery

pack.

Fill the battery cells, if necessary, after the charge using the filling system.

IMPORTANT

USE ONLY DISTILLED OR DEMINERALIZED WATER TO FILL THE

BATTERY CELLS. BATTERY CELLS MUST BE FILLED ONLY

A F T E R T H E C H A R G E ( D U R I N G T H E C H A R G E , T H E

ELECTROLYTE LEVEL INCREASES AND CAN OVERFLOW).

• A draining bulb is supplied with the work platform

NOTE: The water that contacted a battery is classified as

industrial waste, it must be disposed of according to regulations in force.

31210044 – JLG Lift –

8-5

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

Monthly maintenance

Checking voltage and electrolyte specific gravity

NOTE: Voltage and specific gravity measures should not

be performed after battery cells have been filled.

These measures must be done after a complete charge once the charger has been unplugged and the machine has been standing for 15 mn.

• Open the battery cell filling cap.

• Using the hydrometer, take a quantity of electrolyte sufficient so that the float emerges. Ensure the float top does not touch the rubber bulb or that the float does not stick by capillarity to the glass wall.

• Read the value as indicated on the example below :

Various recommendations

Use of a battery in a cold chamber or in a cold climate

Low temperatures decrease battery capacity. The battery must be fully charged when the work platform is operated in a cold chamber or in cold weather condition.

Battery not working continuously or inactive battery

A battery that is not used or used intermittently must be stored charged in a dry area away from freezing temperatures. A charge must be performed once a month.

• Unplug the battery to insulate it electrically.

• Keep the top of the battery clean and dry to prevent self discharge.

IMPORTANT

IF THE BATTERY IS NOT USED CONTINUOUSLY, IT MUST BE

RECHARGED BEFORE USE AND AT LEAST ONCE A MONTH, EVEN

IF THE ELECTROLYTE SPECIFIC GRAVITY MEASURES ARE HIGH.

BEFORE PLACING IN SERVICE A BATTERY WHICH REMAINED

INACTIVE FOR A LONG PERIOD OF TIME, YOU MUST RECHARGE

THE BATTERY AND CHECK THE ELECTROLYTE LEVEL IN THE

CELLS

• Return the electrolyte in the cell and record cell electrolyte specific gravity in the battery service log.

• Repeat operation for each battery cell.

• Contact JLG Industries if important disparities are noticed between the gravity of the different cells and if the values are lower than 1.24.

• Check each cell voltage.

• Contact JLG Industries if important disparities are noticed between the voltage of the different cells.

Annual maintenance

Filling system maintenance

It is necessary to service the centralized filling system at least once a year. Cleaning frequency must be increased in case of premature clogging of the filter or a reduction in water flow.

• Disconnect and clean the filter by reversing the water flow from the normal direction.

• Check the hoses for flexibility. In case of hardening in the connection areas, replace the hose.

• Check every fitting for tightness and leakage.

• Check the cell caps individually. Ensure the perfect mobility of the floats. In case of excessive clogging, replace the cap. In any case, it is recommended to replace the caps every 2 to 3 years.

8-6

– JLG Lift – 31210044

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

Battery troubleshooting

Symptoms

Electrolyte overflow.

Probable causes

Filling done before the charge.

Cells overfilled.

Overcharge.

Filling done before the charge.

Fill battery cells after the charge.

Solutions

Never charge battery if electrolyte specific gravity is above 1,240 kg/l.

Fill battery cells after the charge.

Inequal electrolyte specific gravity or electrolyte specific gravity too low.

Loss of electrolyte due to overflow.

Stratification of the electrolyte.

Electrolyte specific gravity too low.

Perform an equalization charge.

Contact your JLG Distributor/Product Support.

Refer to "electrolyte specific gravity too low".

Low voltage in the cells in open circuit.

Short-circuit.

Problem with the charger.

Clean battery top.

Get the charger checked by a technician.

Battery cells temperature too high (over 113°F

(45°C)).

Bad air circulation during charge.

Cell weak or faulty

Cells shorted.

Battery under charged.

Battery incapable of supporting regular operation.

Open access doors to batteries during charge.

Reduce temperature of the area where the battery is charged (artificial ventilation).

Change battery cell.

Cell faulty.

Faulty cable or connection.

Battery at the end of its service life.

Perform an equalization charge.

Replace faulty cell.

Check wire condition and connection.

Replace the battery.

31210044 – JLG Lift –

8-7

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

Lubrication Specification

A

B

STANDARD

NERVOFLUID VG 32

NERVOFLUID DVG 32

MOBIL DTE 13M

FOOD COMPATIBLE

NERVOL - AGROFLUID DVG 32

MOBIL - DTE FM 32

BIODEGRADABLE

PANOLIN - 3504 HLS

SYNTHESE 32

LOW TEMPERATURE

DOWN -35°C

NERVOL - EQUIVIS XV 32

NERVOL - HYDRALF XV 32

MOBIL DTE 13M

FOOD COMPATIBLE

LOW TEMPERATURE

NERVOL - AGROFLUID

STANDARD

COMPLEX EP2

MOBILUX EP2

LOW TEMPERATURE

DOWN -35°C

NERVOL - CRYOGREASE

MOBILITH SHC 220

2. Hydraulic filters

IMPORTANT

ALWAYS REPLACE BOTH FILTERS AT THE SAME TIME.

Pressure Filter

C

D

STANDARD

MOBILTAC 81

STANDARD

MOBIL DTE 16M

CHAINE FILANTE

LOW TEMPERATURE

DOWN -35°C

HYDRELF XV 32

E

STANDARD

MOBILUX EP2

COMPLEX EP2

• Install a new filter cartridge.

• Install the filter container.

.

Interval - After first 50 hours of operation and every 250 hours thereafter.

• Position the ignition key to "O" position.

• Activate the release valve (located at the rear side of the machine) to release the pressure in the hydraulic circuit

(position the release valve lever to

"release position" ( ).

• Unscrew the filter container.

Return Filter

Interval - After first 50 hours of operation and every 250 hours thereafter.

• Position the ignition key to "O" position.

• Remove the return filter cap and remove the spring.

• Replace the filter cartridge with a new one.

• Check the presence and condition of the

O ring, close the filter cover. Do not forget to install the spring.

IMPORTANT

AFTER INSTALLATION, PERFORM A FEW MOVEMENTS TO

BLEED THE AIR FROM THE HYDRAULIC CIRCUIT, CHECK THE

OIL LEVEL IN THE TANK (PLATFORM IN RETRACTED POSITION).

NOTE: Used oils and cartridges must be disposed of

according to regulations in force.

NOTE: Aside from JLG recommendations, it is not

advisable to mix oils of different brands or types, as they may not contain the same required additives or be of comparable viscosities. If use of hydraulic oil or grease other than recommended in the previous chart, contact JLG Industries for proper recommendations.

HIGH PRESSURE OIL COULD PENETRATE SKIN AND CAUSE

INJURIES OR BURNS.

LOOSEN THE FILTER TANK VERY SLOWLY TO ALLOW THE OIL

PRESSURE TO DROP GRADUALLY.

NOTE: Use a container to collect the oil from the hydraulic

lines or from the filter and prevent it from spilling on the work platform or on the ground.

IMPORTANT

L U B R I C AT I O N I N T E R VA L S A R E B A S E D O N M A C H I N E

OPERATION UNDER NORMAL CONDITIONS. FOR MACHINES

U S E D I N M U L T I - S H I F T O P E R AT I O N S A N D / O R S E V E R E

E N V I R O N M E N T S , L U B R I C A T I O N F R E Q U E N C Y M U S T B E

INCREASED ACCORDINGLY.

8-8

– JLG Lift – 31210044

3. Turntable Lubrication

Bearing Track :

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

5. Mast Section Lubrication

Lube Point - Grease Fitting

Lube - TYPE E

Interval - Every 250 hours of operation.

Grease the bearing track using a grease pump.

Turntable Teeth :

Lube Point(s) - Coat each tooth.

Lube - TYPE C

Interval - Every 1000 hours of operation

• Remove the turntable protection covers.

OPERATION MUST BE PERFORMED ON FLAT AND HORIZONTAL

GROUND, IN AN AREA ALLOWING FULL ROTATION OF THE

STRUCTURE.

• Apply new grease with a brush on the turntable teeth through the reducer’s centering hole. Rotate the structure manually to ensure all the teeth have been greased.

4. Lifting chains lubrication

Lube - TYPE D

Interval - every 125 hours or once every 30 days of operation.

Comments - Lubricant can be applied manually with a brush or by spraying. Apply lubricant :

- Longitudinally : in areas where joints are under small load to facilitate penetration of the lubricant.

- Transversally : between the plates to enable the lubricant to reach the joint and between the internal plates and the rollers.

Lube - TYPE B

Interval - every 125 hours of operation or after each cleaning.

Comments - Clean the inside wall of mast to remove the old grease. Lubricate the mast inside wall using a brush.

6. Wheel Bearing & Steering Knuckle Lubrication

Lube point(s) - 4 Grease Fittings

Lube - TYPE E

Interval - every 125 hours of operation.

Comments - One fitting on each hub and one fitting on each knuckle.

31210044 – JLG Lift –

8-9

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

7. Hydraulic Oil Reservoir h.

i.

j.

Reservoir Filling : f.

g.

k.

l.

Replace the pressure filter cartridge (refer to

"Hydraulic Filters section").

Unscrew the return filter cover and remove the spring.

Remove the filter cartridge.

Fill the tank with new oil to the maximum level.

Install a new filter cartridge, check the presence of the O-ring and close the filter lid.

Perform a few movements to bleed the air from the hydraulic circuit.

Check oil level in the tank through sight gauge on the reservoir and add oil if necessary, with

THE WORK PLATFORM IN RE TRACTED

POSITION, without exceeding maximum level.

Lube point(s) - Return filters

Capacity : 20.5 liters

Lube - TYPE A

Interval - Check oil daily. Change after every 1000 hours of operation or at least every 2 years.

Reservoir Draining :

IMPORTANT

THE FILTERS MUST BE REPLACED WHEN THE OIL IS CHANGED

IN THE MAIN RESERVOIR.

a.

Position the ignition key to "O" position.

b.

Place a container with a minimum capacity of 25 liters under the oil reservoir plug.

c.

Unscrew the drain plug.

NOTE: Do not let the oil spill on the work platform or on the

ground.

d.

Tighten the drain plug once all the oil has been drained.

e.

Used oils must be disposed of according to regulations in force.

8-10

– JLG Lift – 31210044

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

8. Tires And Wheels

Tire wear and damage :

Inspect tires periodically for wear or damage. Tires with worn edges or distorted profiles require replacement.

Tires with significant damage in the tread area or side wall, require immediate evaluation before placing the machine into service.

Wheel installation :

It is extremely important to apply and maintain proper wheel mounting torque.

WHEEL NUTS MUST BE INSTALLED AND MAINTAINED AT THE

PROPER TORQUE TO PREVENT LOOSE WHEELS, BROKEN

STUDS AND POSSIBLE SEPARATION OF WHEEL FROM THE

AXLE. BE SURE THAT THE LUG NUTS ARE SEATED PROPERLY

TO THE WHEEL.

Use a torque wrench to tighten the fasteners. If you do not have a torque wrench, tighten the fasteners with a lug wrench, then immediately have a service garage or dealer tighten the lug nuts to the proper torque. Overtightening will result in breaking the studs or permanently deforming the mounting stud holes in the wheels. The proper procedure for attaching wheels is as follows :

• Start all nuts by hand to prevent cross threading.

DO NOT use a lubricant on threads or nuts.

• Tighten nuts in the following sequence :

9. Verification Of The Tilt Alarm Setting

Interval - Check after every 6 months of operation.

a.

b.

c.

d.

Place machine on a known level surface.

Position the ignition key to "I" position.

Chock both rear wheels.

Place a spirit level (digital display) on the chassis positioned lengthways.

e.

With a jack of appropriate capacity, lift the front of the chassis to tilt level specified in Table 8.1 and ensure that :

• An acoustic alarm sounds when the chassis is tilted at its max value.

• The corresponding LED lights up on the platform controls.

f.

g.

Repeat steps (d) to (e) with the front wheels chocked and lift at the rear.

Place a spirit level (digital display) across the chassis.

h.

With a jack of appropriate capacity, lift the right hand side of the chassis to tilt level specified in

Table 8.1 and ensure that :

• An acoustic alarm sounds when the chassis is tilted at its max value.

i.

• The corresponding LED lights up on the platform controls

j.

Repeat steps (g) and (h) with the left side of the chassis lifted.

Remove the blocks.

Figure 8-2. Wheel Torque Chart

Torque Values (Nm) 150

• Tightening of the nuts should be done in stages.

Following the recommended sequence, tighten nuts as follow :

1st stage

50

Torque Stages (Nm)

2nd stage

100

3rd stage

150

• Wheel nuts should be torqued after first 50 hours or after each wheel removal. Check and torque every 3 months or 150 hours of operation.

IMPORTANT

TIGHTEN THE NUTS USING A TORQUE WRENCH. DO NOT USE

IMPACT WRENCH.

31210044 – JLG Lift –

8-11

SECTION 8 - GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE

This page has been intentionally left blank.

8-12

– JLG Lift – 31210044

Corporate Office

JLG Industries, Inc.

1 JLG Drive

McConnellsburg PA. 17233-9533

USA

Phone: (717) 485-5161

Fax: (717) 485-6417

JLG Worldwide Locations

JLG Industries (Australia)

P.O. Box 5119

11 Bolwarra Road

Port Macquarie

N.S.W. 2444

Australia

Phone: (61) 2 65 811111

Fax: (61) 2 65 810122

JLG Deutschland GmbH

Max Planck Strasse 21

D-27721 Ritterhude/lhlpohl

Germany

Phone: (49) 421 69 350 - 20

Fax: (49) 421 69 350 - 45

JLG Polska

UI. Krolewska

00-060 Warsawa

Poland

Phone: (48) 91 4320 245

Fax: (48) 91 4358 200

JLG Latino Americana Ltda.

Rua Eng. Carlos Stevenson,

80-Suite 71

13092-310 Campinas-SP

Brazil

Phone: (55) 19 3295 0407

Fax: (55) 19 3295 1025

JLG Equipment Services Ltd

Rm 1107 Landmark North

39 Lung Sum Avenue

Sheung Shui N.T.

Hong Kong

Phone: (852) 2639 5783

Fax: (852) 2639 5797

JLG Industries (Scotland)

Wright Business Centre,

1 Lonmay Road

Queenslie

Glasgow G33 4EL

Scotland

Phone: (44) 141 781 6700

Fax: (44) 141 773 1907

JLG Industries (UK) Ltd

Bentley House

Bentley Avenue

Middleton

Greater Manchester

M24 2GP

England

Phone: (44) 161 654 1000

Fax: (44) 161 654 1003

JLG Industries (Italia)

Via Po. 22

20010 Pregnana Milanese - MI

Italy

Phone: (39) 02 9359 5210

Fax: (39) 02 9359 5845

Plataformas Elevadoras

JLG Iberica, S.L.

Trapadella, 2

P.I. Castellbisbal Sur

08755Castellbisbal

Spain

Phone: (34) 93 77 24700

Fax: (34) 93 77 11762

JLG France SAS

Z.I. de baulieu

47400 Fauillet

France

Phone: (33) 553 883 170

Fax: (33) 553 883 179

JLG Europe B.V.

Polaris Avenue 63

2132 HJ Foofddorp

The Netherlands

Phone: (31) 23 565 5665

Fax: (31) 23 557 2493

JLG Sverige AB

Enkopingsvagen 150

Box 704

SE - 176 27 Jarfalla

Sweden

Phone: (46) 8 506 59500

Fax: (46) 8 506 59534

www.jlg.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement

Table of contents