Dimplex Wall Fires Text UK

Dimplex Wall Fires Text UK
(SP4) SP420
(SP5) SP520
(SP9) SP920
AUS/NZ
08/50019/5
Issue 5
Products comply with the European Safety Standard: EN 60335-2-30 and the European Standards for Electromagetic Compatibility (EMC)
EN55014-1 / A2: 2002 and EN55014-2:2003 which cover the essential requirements of EEC directives 73/23 and 89/336
1
SP420
SP520
964
100
min.
100
170
SP920
1200
182
100
650
664
'a'
'a'
300 min.
(600 recommended)
2
1010
168
min.
min.
696
'a'
300 min.
(600 recommended)
300 min.
(600 recommended)
3
A
B
A
B
C
D
E
8
600
5
A
B
C
D
E
SP420
480
240
566
558
1158
SP520
840
280
554
546
1146
SP920
480
240
566
558
1158
4
a
b
5a
Z
A
X
'X'
'X'
B
d
c
Y
6
MAN AUTO
S4
S3
ON
S2
OFF
8
SP420
SP920
SP420 & SP920
SP520
S1
ON
OFF
SP520
S3
S2
S1
7
SP520
SP420
SP920
10
9
SP420
10a
X
A
C
Y
2
1
b
B
a
11
12
b
a
SP520 & SP920
Wall Fires Models: SP420, SP520 & SP920
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
should be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
If the appliance is damaged, check immediately with
the supplier before installation and operation.
Do not use this heater in the immediate surroundings
of a bath, shower or swimming pool.
Do not use outdoors.
Do not cover or obstruct the heater in any way.
Overheating will result if it is accidentally covered.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
The supply cord is recommended to be placed on the
right hand side of the heater. The heater can also be
HARD wired - this is recommended if the heater is
recessed - see ‘Recessed Installation’.
The appliance is not intended for use by young children
or infirm persons unless they have been adequately
supervised by a responsible person to ensure that they
can use the appliance safely.
Young children should be supervised to ensure that they
do not play with the appliance.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or similarly qualified
person in order to avoid a hazard.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Do not switch the appliance on until properly installed. Please
read all the safety warnings and operating instructions.
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
fire to your supplier.
Contents of Carton
•
Heater.
•
Wall fixing bracket.
•
Fixing screws and wall plugs.
•
Remote control and batteries (AAA’s type).
•
Spare bulb.
Do not connect the heater to an electricity supply until it is
installed on a wall correctly - see ‘Installation’.
SP420 & SP920 - When in operation there is a 300 watt heat
output from the fuel effect, and an additional 120 watt output
when the heated glass panel is in operation.
SP520 - When in operation there is a 300 watt heat output
from the fuel effect, and an additional 200 watt output when
the heated glass panel is in operation.
The heater can be used remotely or manually - see ‘Operation’.
General features of remote control are:
•
Activate/Deactivate heated glass panel.
•
The illumination of fuel effect can be increased or
decreased.
Please note: Used in an environment where background
noise is very low, it may be possible to hear the motor which
operates the flame effect. This is normal and should not be
a cause for concern.
Installation
Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is read fully.
The minimum distances must be observed.
For installation of the appliance, care must be taken not to
damage concealed cables.
Please be careful while drilling the holes.
This model is designed to be permanently fixed to a wall at a
minimum height of 300mm. The wall bracket must be fitted
horizontally and the cable routed to the bottom right of the
heater as in Fig. 1.
A height of 600mm from bottom of heater to floor is
recommended for optimum viewing of fuel bed (see Fig. 2 for
recommended fixing dimensions).
For optimum viewing mark the top four screw fixing positions
on wall in accordance with the recommended fixing dimensions
- see Fig. 2. Drill holes with a 6mm drill bit.
Fix the wall bracket using the plugs and screws provided see Fig. 3.
Carefully lift the heater up ensuring that the top rear ledge of
heater engages the wall bracket and is sitting centrally
positioned. - see Fig. 4 (b).
Rotate the bottom fixing bracket down. - see Fig. 4 (c).
Gently bring the heater level with the wall. - see Fig. 4 (d).
Mark the bottom hole position (see Fig. 5), remove the heater
ensuring that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as
in Fig. 4 a, b, c and d) and rotate the bottom fixing bracket
down again and use the screw provided to permanently fix
the heater in place.
The heater should not be connected until the instruction leaflet
is read fully.
Recessed Installation
Please note that this appliance can also be wall-mounted so
that it is recessed. This can be installed in a large fireplace
opening or a purpose built wall. See Table 1 for size of recess
required and hole fixing dimensions and Fig. 5a. This fireplace
insert does NOT require venting.
In order to ensure it’s future safety in use, it is essential
that this fire is securely fixed to the wall.
IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS
APPROPRIATE TO THE WALL MATERIAL TO WHICH THE
FIRE IS BEING FIXED. SOME MODERN INTERNAL
BUILDING MATERIALS ARE VERY LOW DENSITY BLOCK
AND REQUIRE SPECIALIZED FIXING DEVICES TO
PROVIDE A SAFE,SECURE INSTALLATION.
The installation of this fire should be carried out by a competent
person. If in doubt please consult your local builder.
This section provides step by step instructions for selecting a
location and preparing the site to install the fireplace into the
following:
Existing Fireplace
1. Make sure that the fire is located on a flat surface.
2. Seal all draughts and vents to prevent chimney debris
from falling onto the Fireplace Insert. Do not install into an
existing fireplace that is prone to dampness.
3. Remove the fire front panel by following the steps as
outlined in ‘Lamp Replacement’ sections.
4. Locate the 4 fixing holes, position the fire accordingly,
and firmly fix the appliance to the wall using the appropriate
screws - see Fig. 5a.
5. Replace the front panel.
The Standby switch must first be turned ‘ON’ to operate the
heater manually or by remote control.
Note: It takes some time for the receiver to respond to the
transmitter. DO NOT PRESS the buttons more than once within
two seconds for correct operation.
To go to the previous settings press the O button.
Pressing the O button on the remote turns off the light & heat
settings. To resume press the I button until the desired setting
is reached - see Fig. 8.
To increase or decrease the brightness of the flames, use the
dimmer button or the button on the Remote Control. The
heat setting will remain the same.
New Support Structure Construction
To turn off the power the Standby Switch must be turned ‘OFF’.
When planning where to position your purpose built support
structure the following steps must be observed:
Replacing the remote control - SP420 &
SP920
1. Place the fire in the desired location to see how it will
look in the room.
2. Mark the desired location for the new support structure
in the room and store the fire in a safe, dry and dust free
location.
3. Using timber studs to support the fire, devise and
construct a suitable means of supporting the product within
the wall partition and provide electrical power for the fire to
be HARD wired. For recommended sizes of height, width
and depth of opening for recess and hole fixing dimensions
for each model - see Table 1 and Fig. 5a.
4. When the structure is complete, remove the front panel
of the fire by following the steps as outlined in ‘Lamp
Replacement’ sections.
5. Locate the 4 fixing holes, position the fire accordingly,
and firmly fix using the appropriate screws.
6. Replace the front panel.
TABLE 1
Models
A
B
SP420
SP520
871
1160
570
560
SP920
914
565
X
Y
Z
847
1143
646
640
115
146
895
676
150
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
Please consult a qualified electrician for appropriate wiring
requirements.
Manual Operation - SP420 & SP920
The switches are located at the bottom right side of the heater.
The Standby Switch (Switch S1) must be first turned ‘ON’ and
the AUTO/MAN (Switch S2) switch set to ‘MANUAL’ to operate
the manual controls - see Fig. 6.
Note : When the fire is put in Manual mode the first time the
flame effect will come on indicated by the Bottom neon coming
on for 3 seconds - see Fig. 7.
The new remote control must be set up as follows:
Press switch S1 to ON.
Press switch S2 to AUTO (see Fig. 6).
Press switch S3 to O for more than 3 seconds until the LED’s
are on (see Fig. 7).
Press the ‘ I ’ button on the remote control.
Now the heater has learned the serial number from the remote
control and will work with this remote control only (this
procedure is repeatable many times).
Lamp Replacement - SP420
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE REMOVING LAMPS.
Warning - The lamps reach high temperatures during
operation. For this reason, allow the lamps to cool down after
switching off the appliance.
The front panel will need to be removed in order to change
lamps –see Fig. 10.
Warning - The front panel is heavy and easily damaged.
The front panel is fixed with 4 spring loaded pins (see ‘a’ in
Fig. 9) and is supported at the top by the chassis.
To gain access to lamps please apply the following
procedure:
While holding the front panel by its sides with both hands,
carefully pull forwards the panel at the bottom until the pins
detach from the clips - see Fig. 9.
When the bottom holding pins are undone, carefully pull
forwards at the top until the top pins detach and then lift the
front panel up and out (see Fig. 10).
To gain access to the bulbs remove the screws at ‘A’ to remove
the cover bracket ‘X’ - see Fig. 10a.
For access to the bottom bulbs, carefully slide the flexible
rotisserie (see ‘a’ in Fig. 11) to one side ensuring that the
rubber grommet is not lost (see ‘b’ in Fig. 11).
Manual Operation - SP520
Remove the defective lamp by unscrewing it (see Fig. 11).
The switches are located at the bottom right side of the heater
- see Fig. 6.
Replace with a 60W E14 SES Clear Candle bulb, rotating it.
Take care not to over-tighten the lamp.
Remote Operation
Steps for reassembling the heater
The standby switch (S1) must first be turned ‘ON’ (and the
‘AUTO/MAN’ Switch turned to ‘AUTO’ - SP420 & SP920).
Note: It takes some time for the receiver to respond to the
transmitter. DO NOT PRESS the buttons more than once within
two seconds for correct operation.
Manual & Remote Operation
Setting
Operation
Setting
Flame Effect only
Press the ‘ I ’ button (Switch 3)
Top Neon
Flame Effect & Heat On
Press the ‘ I ’ button again (Switch 3)
Bottom Neon
1. Refit the rotisserie making sure that the rubber grommet
is carefully pushed into the slotted hole on the axial bracket.
2. Replace the cover bracket ‘X’ - see Fig. 10a.
3. Replace the front by aligning the slots on the front frame
and making sure that it catches fully on the support
brackets.
Lamp Replacement – SP520 & SP920
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE REMOVING LAMPS.
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
Warning - The lamps reach high temperatures during
operation. For this reason, allow the lamps to cool down after
switching off the appliance.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth. DO NOT use proprietary
glass cleaners.
The front panel will need to be removed in order to change
lamps – see Fig. 12.
Warning - The front panel is heavy and easily damaged.
The front panel is supported at the top by the chassis and
held tight by magnets at the top and bottom.
To gain access to lamps please apply the following
procedure:
While holding the front panel by its sides with both hands,
carefully lift the panel up (1) and then away (2) from the main
body - see Fig. 12.
To gain access to the bulbs remove the screws at ‘A’ to remove
the cover bracket ‘X’ and the screws at ‘B’ to remove the cover
bracket ‘Y’ - see Fig. 10a.
The bottom cover bracket ‘Y’ is also held on by magnets. To
remove this bracket, (1) gently tilt the bottom of the bracket
out and then (2) lift out - see Fig. 10a.
For access to the bottom bulbs, carefully slide the flexible
rotisserie (see ‘a’ in Fig. 11) to one side ensuring that the
rubber grommet is not lost (see ‘b’ in Fig. 11).
Remove the defective lamp by unscrewing it (see Fig. 11).
Replace with a 60W E14 SES Clear Candle bulb, rotating it.
Take care not to over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber grommet
is carefully pushed into the slotted hole on the axial bracket.
2. Replace the cover brackets ‘X’ and ‘Y’ ensuring that the
magnets at the top of cover bracket ‘Y’ catch the fuel effect
bracket ‘C’ to prevent vibration - see Fig. 10a.
3. Replace the front by aligning the slots on the front frame
and making sure that it catches fully on the support brackets.
The magnets on the chassis will hold the front flush to the
main body.
After Sales Service
Should you require after sales service, please get in touch
with the supplier through whom you purchased the appliance.
Please retain your receipt as proof of purchase.
The product complies with the Australian/New Zealand Safety Standards AS/NZ S 335.2.30:1997 and 2002 Part 1 also the European Standard ElectromagneticCompatibility (EMC) EN 55 0141:1993, EN 61000-3-2:1995, EN 61000-3-3:1995, EN 55 014-2:1997 which cover the essential requirements of EEC Directive 89/336/EEC.
Specification subject to change without prior notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising