Step 1 – PREPARING TO MOUNT THE CAMERA

Step 1 – PREPARING TO MOUNT THE CAMERA
Quick Start Guide
Quick Start Guide
Step 1 – PREPARING TO MOUNT THE CAMERA
Template
Sheet
1
1. The mounting surface must bear five times the weight of your camera.
4
2. Do not let the cables get caught in improper places or the electric line cover to
be damaged. This may cause a breakdown or fire.
3. For the installation process, remove the dome cover from the camera module
by loosening the three (3) screws on the dome. Use the wrench provided with
the camera.
DWC-MV72I4V / DWC-MV72I28V
4. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
5
Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
2
5. Pass the wires through the mount bracket and make all necessary connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission and
use a power adapter to power the camera.
Power Requirements
Username: admin
Password: admin
DC 12V
PoE IEEE 802.3atPoE+ / PoE Class 2
Power Consumption
WHAT’S IN THE BOX
NETWORK
CONNECTION
LED Off: 1.92W, 160mA
LED On: 2.7W, 230mA (IR models only)
POWER
QSG Manual
1 Set
Mount Bolt &
Nut – 2pcs
1 Set
Manual CD
1 Set
Screw & Plastic
Anchor – 2pcs
1 Set
Template Sheet
for installing by
Bolt & Nut
1 Set
Torx Wrench
1 Set
Step 3 – INSTALLING THE CAMERA
3
6. To use the camera’s water proof wiring:
(1). Install the LAN cable into (a).
(2). (b) will be assembled to (a)
with a 1/4 turn.
(3). Thread (c) tightly to (b).
c
b
a
Reset
Button
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper
camera usage.
Tel: 866-446-3595 / 813-888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Note: To ensure moisture seal, make sure the o-ring is in place between
(a) and (b). In extreme environments use of an outdoor rated sealer
is recommended.
7. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle. The
camera’s maximum tilting angle is 70.
8. Assemble the dome cover over the camera body and detach the protecting film
from the dome bubble.
Resetting the camera: To reset the camera, use the tip of a paper clip or
a pencil and press the reset button. Pressing the button for five (5) seconds
will initiate a camera-wide reset of all the settings, including network settings.
Quick Start Guide
Step 3 – INSTALLING THE CAMERA (CONT.)
Installation using Mount Bolt and Screws:
Camera's Network Settings
Camera's Firmware
Search for
Cameras
Filter Search
Results
Camera Name,
Model, IP Address,
and MAC Address
1. Using the template sheet, make and drill the cabling holes on the wall/ceiling.
View Camera's
Thumbnail View
Camera Uptime
6. To save the changes made to the camera’s settings, input the ID and PW of the
camera for authentication and click ‘Save’.
7. If the camera needs to be rebooted after the settings were changed, press the
‘Reboot’ button. The camera will cycle power and will appear back in the search
results once the reboot is complete.
2. Secure the two long mounting screws to the camera’s base.
3. Pass the wires through the mount bracket and make all necessary connections.
Default ID / PW : admin / admin
4. Mount the camera to the mounting surface by using the 2 mounting nuts.
Rotate the locking discs over the screws until the camera is held tightly from
the mounting surface.
DWC-­‐MF10M28T DWC-­‐MF10M28T DWC-­‐MF21M4TIR DWC-­‐MF21M4TIR Firmware Upgrade
Step 5 – WEB VIEWER
Open Camera's IP
Configuration Screen
Select DHCP if the internet service is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Note: The camera’s maximum tilting angle is 70°
Contact your network administrator for more information.
4. The camera’s default network information is:
Step 4 – DW IP FINDER™
Use the DW IP Finder™ included in the camera’s accessory CD to scan the network
and detect all MEGApix® cameras, set the camera’s network settings, perform
firmware upgrade or access the camera’s web client.
Once the camera’s network settings have been setup properly, you can access the
camera’s web viewer using the DW IP Finder™. To open the camera’s web viewer:
Default TCP/IP information
1. Find the camera using the DW IP Finder™.
•
•
•
•
2. Double-click on the camera’s view in the results table.
IP: 192.168.1.80
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
DNS: 168.126.63.1
3. Press the ‘View Camera Website’. The camera’s web viewer will open up in
your default web browser.
Network Setup
4. Enter the camera’s username and password (default are admin / admin).
1. Run the CD included with the camera and click on the DW IP Finder ™ file.
5. If you are accessing the camera for the first time, install the VLC files in
order to view video from the camera.
2. The software will scan your network for all supported cameras and display the
results in the table. Allow up to 5 seconds for the IP Finder to find the camera on
the network.
3. Select a camera from the list by double-clicking on the camera’s image or
clicking on the ‘Click’ button under the IP Conf. column. The camera’s network
information will appear. If necessary, you can adjust the camera’s network type.
5. To view the camera’s web viewer, click on ‘View Camera Website’.
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
Note: Please see the full product manual for web viewer setup, functions
and camera settings options.
Rev Date: 3/16
Copyright © Digital Watchdog. All rights reserved. Specifications
and pricing are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising