GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS
INSTALLATION INSTRUCTIONS
1.
2.
3.
DESCRIPTION: Fog Lamp Kit
APPLICATION: Frontier, Xterra and Pathfinder (2009~)
PART NUMBER: 999F1 BV000 - Frontier (with Steel Bumper) fog lamp kit
999F1 KV000 - Frontier (with Colored Facia) and Xterra fog lamp kit
999F1 XV000 - Pathfinder fog lamp kit
4.
KIT CONTENTS:
Item
Description
A
B
C
D
E
F
G
H
I
J
5.
6.
Combi Switch
Front Fog Lamp Finisher
Fog lamp assembly (RH/LH)
Fog lamp assembly
Fog lamp assembly (RH/LH)
Hex Bolt (Shorter)
Hex Bolt (Longer)
U-Shape Nut
Spring Clip
II Replacement Template
Service Part Number
25560 ET11E
62256/7 EA800
26150/5 EA800
26150 EA000
26150/5 EA500
81-46616-2G
81-46616-5G
12-41 0009U
15-54 0007U
999V2 AW000
Quantity and Application
KV000
XV000
BV000
1
1
1
1
--1
---2
---1
2
2
4
2
---2
2
-2
-1
1
1
A
B
C
D
E
F
G
H
I
J
TOOLS REQUIRED:
● Flat tip screwdriver
● Phillips screwdriver
● 10mm socket
● 10mm wrench
PRE-INSTALLATION CAUTIONS/NOTES:
● Dealer Installation Recommended. Instructions refer to Service Manual.
Page 1 of 7
999F1 XV000II 7/12/11
7.
INSTALLATION PROCEDURE:
NOTE : Steps 1 ~ 4 apply to all applications.
Fig 1
1) Remove 3 screws (A) from lower steering
column cover then remove the upper
cover (B).
Fig 2
2) Remove lighting and turn signal switch.
a) While pressing tabs (A), pull switch
toward driver's door (B).
3) Install kit supplied Lighting and Turn
Signal Switch.
4) Install the steering column upper and lower
covers using the original screws.
5) RH/LH - Remove inner fender.
NOTE: Step 5 not necessary for most
Frontier models.
NOTE: Removing the tire/wheel may allow
better access for inner fender removal.
Fig 3
Pathfinder and Xterra
Page 2 of 7
999F1 XV000II 07/12/2011
Fig 4
6) RH/LH - Remove foglamp covers/inserts.
Frontier
Fig 5
Frontier
Xterra
Fig 6
Pathfinder
Page 3 of 7
999F1 XV000II 07/12/2011
Fig 7
7) RH/LH - Locate and untape the fog lamp
wiring harness connectors.
Frontier
Fig 8
Xterra
Fig 9
Pathfinder
Page 4 of 7
999F1 XV000II 07/12/2011
Fig 10
8) RH/LH - Install fog lamp assemblies.
NOTE :
Frontier only: Short bolt must be used on top
mount.
Frontier (Steel Bumper)
Fig 11
Xterra/Frontier (Colored Bumper)
Fig 12
Pathfinder
Page 5 of 7
999F1 XV000II 07/12/2011
Fig 13
9) RH/LH - Connect harness to fog lamp.
Frontier
Fig 14
Xterra
Fig 15
Pathfinder
Page 6 of 7
999F1 XV000II 07/12/2011
10) RH/LH - Install inner fender.
NOTE: Step not necessary for most Frontier
models.
Fig 16
Pathfinder and Xterra
11) RH/LH - Install trim ring.
Fig 17
NOTE : Frontier only.
Frontier (with Steel Bumper)
12)
8.
Refer to Service Manual for Aiming
Adjustment.
FUNCTIONALITY TEST PROCEDURE:
1) Turn ignition switch ON.
2) Turn headlamp and fog lamp switches ON.
3) Verify headlamps and fog lamps are illuminated.
4) Perform fog-light and head-light aiming check.
5) Turn headlamp switch OFF (leaving fog lamp switch ON).
6) Verify both headlamp and fog lamps turn off.
7) Verify turn signal and high beam functionality.
Page 7 of 7
999F1 XV000II 07/12/2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising