IQAir GC Series Air Purifier Filter Installation Instructions | Sylvane

IQAir GC Series Air Purifier Filter Installation Instructions | Sylvane
Adapterring_2_A4_GB
29.11.2006
7:22 Uhr
Seite 1
www.sylvane.com 1-800-934-9194
Air Cleaning Perfection
Installation Instructions
for Filter Cartridges of
GC, GCX and Dental Series
Air Purifiers
Table of Contents
Chapter 1
Preparing the Cartridges for Insertion
2
Chapter 2
Opening the IQAir Air Purifier
2
Chapter 3
Inserting Cartridges into “Sawblade”-Type Plate
3
Chapter 4
Inserting Cartridges into “Keyhole”-Type Plate
3
Chapter 5
Closing the IQAir Air Purifier
4
Adapterring_2_A4_GB
29.11.2006
7:22 Uhr
Seite 2
www.sylvane.com 1-800-934-9194
Chapter 1 – Preparing the Cartridges for Insertion
1
2
Pull a post-filter sleeve over each of the cartridges. With new IQAir
systems the sleeves are supplied inside of the IQAir System (refer to
Chapter 2 on how to open the IQAir System).
Chapter 2 – Opening the Air Purifier
1
2
Pull both locking arms outwards evenly until they snap into place
and remain open.
Pull the first locking arm outward to release the arm from its snapin position in the diffuser. Disengage the other arm the same way.
3
4
“Sawblade”-Type
“Keyhole”-Type
Remove the diffuser and the top two (GCX top four) frame elements.
Page 2
You will find either a “Sawblade”-Type or “Keyhole”-Type plate
within the bottom frame element. Follow the appropriate instructions for your plate type.
Adapterring_2_A4_GB
29.11.2006
7:23 Uhr
Seite 3
www.sylvane.com 1-800-934-9194
Chapter 3 – Inserting Cartridges into the “Sawblade”-Type Plate
1
2
“Sawblade”-Type
For the “Sawblade”-Type plate…
4
th
e Top
ca o
rt f
rid
ge
3
…use the cartridge without the grey adapter ring. If the ring is
pre-fitted to the cartridge, turn the ring counter-clockwise…
“Overhead View”
…and lift it off the cartridge. (The grey adapter ring will not be
needed and can be disposed of.)
Turn the cartridge around and insert it into one of the plate slots.
Turn the cartridge clockwise until it is securely locked onto the
plate. Repeat steps 2 – 4 with remaining cartridges. Proceed to
Chapter 5.
Chapter 4 – Inserting Cartridges into the “Keyhole”-Type Plate
1
2
“Keyhole”-type
For the “Keyhole”-Type plate…
…use the cartridge with the grey adapter ring in place.
Page 3
Adapterring_2_A4_GB
29.11.2006
7:23 Uhr
Seite 4
www.sylvane.com 1-800-934-9194
4
th
e Top
ca o
rt f
rid
ge
3
“Overhead View”
Once inserted into the slots, turn the cartridge clockwise until it is
securely locked onto the plate. Repeat steps 2 – 4 with the remaining cartridges, then proceed to Chapter 5.
The cartridge with the grey adapter ring can then be inserted into
the keyhole slots in the plate.
5
6
Note: If you remove the cartridge again, the grey adapter ring will
stay locked on the plate.
Since the grey adapter ring has now become an integrated part of
the plate, no additional adapter rings will be needed for future
replacement of cartridges.
Chapter 5 – Closing the IQAir System
1
2
Refit the housing element with the inserted cartridges onto the
IQAir System…
…replace the remaining housing element(s) and the diffuser. Close
the two locking arms simultaneously until they securely lock into
the diffuser.
IMPORTANT: When used cartridges have been replaced with new cartridges, the appropriate filter life monitor must be reset in the IQAir’s control panel.
Refer to the IQAir user manual for instructions.
Page 4
105 03 00 22 / 1106
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising